TP-Link TL-SF1005LP User Manual
LED Explanation
© 2020 TP-Link 7106508683 REV2.0.0
Installation Guide
5-Port 10/100Mbps Desktop PoE/PoE+ Switch
Switch Explanation
Priority (Port 1–2)
O: All the ports transmit data in the same priority.
On: Port 1 and 2 transmit data in a higher priority than other ports. When
congestion occurs, packets which are transmitted by the ports with higher
priority occupy the whole bandwidth.
Power
On: Power on
Power
O: Power o
Link/Act and PoE Status
On: Link present but no
activity
Flashing: Transmitting/
receiving data
O: No link
On: Providing PoE power
Flashing: Current-overload/
Short-circuit
O: Not providing PoE power
Extend (Port 1–4)
O: Port 1–4 run at 10/100 Mbps and support PoE power supply up to 100 m
away.
On: Port 1–4 run at 10 Mbps and support PoE power supply up to 250 m away.
PoE MAX
TL-SF1005LP
On: 34 W≤Total power supply < 41 W
PoE Max
Flashing: Total power supply ≥ 41 W
O: Total power supply < 34 W
TL-SF1005P
On: 60 W≤Total power supply < 67 W
Flashing: Total power supply ≥ 67 W
O: Total power supply < 60 W
Note: For simplicity, we will take TL-SF1005P for example throughout the Guide.
Connection
PoE Ports (1-4)
PoE Devices
DC Power Adapter
Ethernet Ports (1-5)
Router
LAN Port
WAN Port
AC Power Cord
Internet
IP Camera AP IP Phone
Note: 1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. TL-SF1005LP can supply up to 15.4 W for each PoE port and 41 W for all PoE
ports.
3. TL-SF1005P can supply up to 30 W for each PoE port and 67 W for all PoE ports.
Frequently Asked Questions (FAQ)
Specications
Q1. Why is the Power LED not lit?
The Power LED should be lit when the power system is working normally. If the
Power LED is not lit, please try the following:
A1: Make sure the AC power cord is connected to the switch with power source
properly.
A2: Make sure the voltage of the power supply meets the requirements of the
input voltage of the switch.
A3: Make sure the power source is ON.
Q2. Why is the Link/Act LED not lit while a device is
connected to the corresponding port?
Please try the following:
A1: Make sure that the cable connectors are rmly plugged into the switch and
the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Q3. Why are PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the
maximum, the PoE port with a smaller port number has higher priority. The
system will cut o power to the ports with larger port numbers to ensure
supplying to other ports.
Take TL-SF1005P as an example. If port 1, 2 and 4 are consuming 15.4 W
respectively, and an additional PoE device with 21 W is inserted to port 3, the
system will cut o the power of port 4 to compensate for the overload.
General Specications
Standard
Protocol
Interface
Network Media (Cable)
Switching Capacity
MAC Address Table
Transfer Method
MAC Address Learning
Power Supply
Wall Mountable
Distance Between
Mounting Holes
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE 802.3af,
IEEE802.1p
IEEE 802.3at (Only for TL-SF1005P)
CSMA/CD
5 10/100 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-Port 4
Total Power Supply:
41 W (for TL-SF1005LP)/67 W (for TL-SF1005P)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
1 Gbps
2K
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input:
100-240 VAC, 50/60 Hz
Output:
53.5 VDC /0.81 A (for TL-SF1005LP)
53.5 VDC /1.31 A (for TL-SF1005P)
Ye s
39 mm
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome
to email techwriter@tp-link.com.cn.
PoE Disclaimer
The speed of the ports in extend mode will downgrade to 10 Mbps. The actual transmission
distance may vary due to power consumption of PoE-powered devices or the cable quality and
type.
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not
guaranteed and will vary as a result of client limitations and environmental factors
.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Environmental and Physical Specications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Use only power supplies which are provided by manufacturer and in the origin packing of
this product. If you have any questions, please don’t hesitate to contact us.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Loading...