TOSHIBA 2555 DB
General Information
Also Covers
2855 DB
2852 DB
2552 DB
Safety Instructions
X-RAY RADIATION PRECAUTION
1.The E.H.T. must be checked every time the receiver is serviced to ensure that the C.R.T. does not emit X-ray radiation as result of excessive E.H.T. voltage. The nominal E.H.T. for this receiver is 26.5 kV at zero beam current (minimum brightness) operating at 240V a.c. The maximum E.H.T. voltage permissible in any operating circumstances must not exceed 29.0 kV. When checking the E.H.T., use the ‘High Voltage Check’ procedure in this manual using an accurate E.H.T. voltmeter.
2.The only source of X-RAY radiation in this receiver is the C.R.T. To prevent X-ray radiation, the replacement C.R.T. must be identical to the original fitted as specified in the Parts List.
3.Some components used in this receiver have safety related characteristics preventing the C.R.T. from emitting X-ray radiation. For continued safety, replacement component should only be made after referring the Product Safety Notice below.
SAFETY PRECAUTION
1.This receiver has a nominal working E.H.T. voltage of 24.5 kV. Extreme caution should be exercised when working on the receiver with the back removed. Do not attempt to service this receiver if you are not conversant with the precautions and procedures for working on high voltage equipment. When handling or working on the C.R.T., always discharge the anode to the receiver chassis before removing the anode cap. The C.R.T., if broken, will violently expel glass fragments. Use shatter
proof goggles and take extreme care while handling. Do not hold the C.R.T. by the neck as this is a very dangerous practice.
2.It is essential that to maintain the safety of the customer all cable forms be replaced exactly as supplied from factory.
3.A small part of the chassis used in this receiver is, when operating, at approximately half mains potential at all times. It is therefore essential in the interest of safety that when serving or connecting any test equipment the receiver should be supplied via a suitable isolating transformer of adequate rating.
4.Replace blown fuses within the receiver with the fuse specified in the parts list.
5.When replacing wires or components to terminals or tags, wind the leads around the terminal before soldering. When replacing safety components identified by the international hazard symbols on the circuit diagram and parts list, it must be a Toshiba approved type and must be mounted as the original.
6.Keep wires away from high temperature components.
PRODUCT SAFETY NOTICE
Many electrical and mechanical components in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the X-ray radiation protection afforded by them cannot necessarily be obtained by using replacements rated at higher voltages or wattage, etc. Components which have these special safety characteristics in this manual and its supplements are identified by the interna-
Recommended Safety Parts
Item |
Part No. |
Description |
C440 |
24082581 |
PF, 7000pF, ± 3%, 1500V |
C463 |
24212222 |
CD, 2200pF, ± 10% |
C801 |
24082318 |
PF, 0.1 F, ± 20%, AC250V |
C802 |
24094656 |
CD, 2200pF, ± 20%, AC400V |
C803 |
24094656 |
CD, 2200pF, ± 20%, AC400V |
C804 |
24082318 |
PF, 0.1pF, ± 20%, AC250V |
R327 |
24339479 |
MF, 4.7 ohm, 2W |
R448 |
24338338 |
ME, 0.33 ohm, 1W |
R801 |
24004914 |
Metal-Glazed Resistor, 5.6M ohm, 1/2W |
R878 |
24531560 |
FR, 56 ohm, 1/2W |
R884 |
24531120 |
FR, 12 ohm, 1/2W |
3890 |
24019340 |
PTC Thermistor, 18 ohm, 290V |
3920 |
24000907 |
FR, 3.9 ohm, 1W |
RD01 |
24000211 |
FR, 15 ohm, 1/2W |
RV25 |
24019261 |
FR, 47 ohm, ± 2%, 1/4W |
L462 |
------------- |
DY, Supplied with V901 |
L901 |
23200275 |
Coil, Degaussing, TSB-2329BR (2555DB/2552DB) |
L901 |
23200276 |
Coil, Degaussing, TSB-2330BR (2855DB/2852DB) |
T401 |
23224336 |
Transformer, Horiz. Drive, TLN1083 |
T461 |
23236454 |
Transformer, Flyback, TFB41 17AR |
T801 |
23211670 |
Line, Filter, TRF3164G |
T803 |
23217214 |
Transformer, Converter, TPW3283AR |
Q404 |
A6872801 |
Transistor, 2SD2253(FA) |
Q826 |
A8643108 |
Photo Coupler, TLP621(GR-LF |
Q827 |
A6907751 |
IC, S1854 |
F801 |
23144507 |
Fuse, 3.15A |
F803 |
23144874 |
Fuse, 0.8A |
P801 |
23372012 |
Power Cord |
V901A |
23902891 |
Socket, CRT, lop |
V901 |
23312462 |
Picture Tube, A59EAK71X01 (2555DB/2552DB) |
V901 |
23312463 |
Picture Tube, A66EAK71X01 (2855DB/2852DB) |
1
tional hazard symbols on the schematic diagram and parts list. Before replacing any of these components read the parts list in this manual carefully. Substitute replacement components which do not have the same safety characteristics as specified in the parts list may create X- ray radiation
Service Adjustments
GENERAL INFORMATION
All adjustments are thoroughly checked and corrected when the receiver leaves the factory. Therefore the receiver should operate normally and produce proper colour and B/W pictures upon installation. However, several minor adjustments may be required depending on the particular location in which the receiver is operated.
This receiver is shipped completely in cardboard carton. Carefully draw out the receiver from the carton and remove all packing materials. Plug the power cord into a convenient 240 volts 50 Hz AC two pin power outlet. Turn the receiver ON. Check and adjust all the customer controls such as BRIGHTNESS, CONTRAST and COLOUR Controls to obtain natural colour or B/ W picture.
AUTOMATIC DEGAUSSING
A degaussing coil is mounted around the picture tube so that external degaussing after moving the receiver is normally unnecessary, providing the receiver is properly degaussed upon installation. The degaussing coil operates for about 1 second after the power to the receiver is switched ON. If the set is moved or faced in a different direction, the power switch must be switched off at least 30 minutes in order that the automatic degaussing circuit operates properly. Should the chassis or parts of the cabinet become magnetized to cause poor colour purity, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube, the sides and front of the receiver and slowly withdraw the coil to a distance of about 2 m before disconnecting it from AC source. If colour shading still persists, perform the COLOUR PURITY ADJUSTMENT and CONVERGENCE ADJUSTMENTS procedures.
HIGH VOLTAGE CHECK
CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis.
1.Connect an accurate high voltage meter to the second anode of the picture tube.
2.Turn on the receiver. Set the BRIGHTNESS and CONTRAST Controls to minimum (zero beam current).
3.High voltage will be measured below 29.0 kV.
HORIZONTAL CENTRE ADJUSTMENT
1.Receive the UK PHILIPS pattern.
2.Set the contrast and colour to centre, and the brightness to centre.
3.Adjust H. CENTER USER Control (R452) so the pattern centre can be located at the screen centre.
FOCUS ADJUSTMENT
Adjust FOCUS Control on FLYBACK TRANS. (T461) for well defined scanning lines in the centre area on the screen.
SIF FM DET (LG04) ADJUSTMENT (NICAM BOARD)
1.Connect SIF generator through 0.01 pF capacitor to pin D1 of PD01 on NICAM Board.
2.Connect the oscilloscope to pin 9 of ICD03.
3.Set up the SIF generator as described. Sound carrier frequency: 6.0 MHz Modulation frequency :1000 Hz Frequency
deviation : ± 15 kHz
Signal level :100 dBp (50 ohm load)
4.Adjust LG04 for the maximum response of 1000 Hz det-out on scope.
PAL MATRIX ADJUSTMENT
1.Tune in the colour programme of the Philips pattern.
2.Set the COLOUR Control to obtain the proper colour.
3.If the PAL MATRIX adjustment is incorrect, the Venetian Blind would appear in the colour bars area. This case needs the adjustment.
4.At the first, adjust DL PHASE ADJ. Coil (L551) to minimize the Venetian Blind.
5.Next adjust 1H-DL ADJ. VR (R551) to minimize the Blind.
6.If the Venetian Blind still remains, adjust 1 H- DL PHASE ADJ. Coil (L551) to minimize the Blind again.
7.Repeat the item 5 and 6 procedures, adjust the R551 and L551 until the Blind does not appear.
CRT GREY SCALE ADJUSTMENT
1.Tune in an active channel.
2.Set the SERVICE SW. (S202) in the “H. LINE” position.
3.Turn the SCREEN Control (on T461) fully counterclockwise.
4.By rotating the RED, GREEN and BLUE CUT OFF Controls (R557, R558, R559) to the mid position.
5.Set the GREEN and BLUE DRIVE Controls (R252, R253) to the center.
6.Rotate the SCREEN Control gradually clockwise until the first line appears slightly on the screen. Set the SCREEN Control to this position.
7.Adjust the CUT OFF Controls to obtain the slightly lighted horizontal lines in the same levels of three colours (RED, GREEN and BLUE). The lines may look like white if the CUT OFF Controls are adjusted properly.
8.Set the SERVICE SW. (S202) in the “RECEIVE” position.
9.Set the CONTRAST and COLOUR Controls to minimum, and BRIGHTNESS Control to the maximum.
10.Adjust the BLUE and GREEN DRIVE Controls (R252/R253) to obtain proper whitebalanced picture in high light areas.
11.Set the BRIGHTNESS and CONTRAST Controls to obtain dark grey raster. Then check the white balance in low brightness. If the white balance is not proper, retouch the CUT OFF Controls and DRIVE Controls to obtain a good white balance in both low and high light areas.
SUB-BRIGHTNESS ADJUSTMENT
1.Tune in a colour programme.
2.Set the CONTRAST Control to the minimum and the BRIGHTNESS Control to the centre.
3.Set the COLOUR Control to the centre.
4.Set the SUB-BRIGHT. Control (R255) to the centre and leave the receiver for five minutes in this state.
5.Watching the picture well, adjust the SUBBRIGHT. Control in the position where the picture does not show evidence of blooming in high bright area and not appear too dark in low bright portion.
6.Check the proper picture variation by rotating the CONTRAST and BRIGHTNESS Controls to both extremes.
7.If the picture does not appear dark with the CONTRAST and BRIGHTNESS Controls turned to the minimum, or not appear bright with the controls turned to the maximum, adjust the SUB-BRIGHT. Control again for the acceptable picture.
Service Mode General
Instructions
1. ENTERING TO SERVICE MODE
1) Press button once on Remote Control.
2) Press button again to keep pressing.
3) Keep pressing the button, press MENU button on TV set.
RCUT |
S |
32H |
|
(Service mode dIsplay)
2. SELECTING THE ADJUSTING ITEMS
Every pressing of CHANNEL ▲ button changes the adjustment items in the following order.
(▼ button for reverse order.)
3. ADJUSTING THE DATA
Pressing of VOLUME ▲ or ▼ button will change the value of data in the range from 00 to FF. The variable range depends on the adjusting item.
4. NORMAL OPERATION ON THE SERVICE MODE
Press MENU button on TV.
5. EXIT FROM SERVICE MODE
Press POWER button on the remote control to turn off the TV once.
See next page for Adjustment Procedure and Rom Data List.
SUB DATA ADDITIONAL DESCRIPTION
Symbol |
Description |
HIT |
V amplitude adjustment. |
LIN |
V linearity correction 1. |
|
Linearity balance |
|
between top and bottom |
|
screen. |
VSC |
V linearity correction 2. |
|
Linearity balance |
|
between top/bottom and |
|
center. |
VPC |
V picture position |
|
adjustment |
VCP |
Setting of amount of V |
|
amplitude correction |
|
against variation of |
|
screen brightness. |
WID |
H amplitude adjustment. |
DPC |
H pin-cushion distortion |
|
correction. |
CNR |
H pin-cushion distortion |
|
correction at four |
|
corners. |
KEY |
Pedestal distortion |
|
correction. |
HCP |
Setting of amount of H |
|
amplitude correction |
|
against variation of |
|
screen brightness. |
VMC |
V linearity correction. |
|
Linearity balance at 1/4, |
|
3/4 areas from top. |
Service Mode / Safety Parts / Safety Instructions / Service Adjustments / Adjustment Procedure / Block Diagram
Signal Processing (2555 & 2855) ... Cont’d / Signal Processing (2552 & 2852) ... Cont’d
Power Audio Deflection (2555 & 2855) ... Cont’d / Power Audio Deflection (2552 & 2852) ... Cont’d
TOSHIBA 2555 DB |
2 |
Adjustment Procedure
Adjustment parts or |
Input point/ |
Adjustment signal |
Adjustment conditions and procedures |
Bus control item |
Output point |
|
|
|
|
|
|
Horizontal amplitude |
Visual check of picture |
WG Philips pattern |
1. Conditions: After V. HEIGHT, VERT POSITION |
adjustment (WID) |
(Bus control) |
|
and H. CENT have been adjusted, set |
Pin distortion |
|
Do not use the Philips |
the controllers as follows: |
compensation amount |
|
pattern of |
Contrast: MAX |
adjustment (DPC) |
|
FRANCESECAM. |
Brightness: Center |
Keystone distortion |
|
|
Color: Center |
compensation amount |
|
|
2. Adjustment procedure |
adjustment (KEY) |
|
|
a. Adjust the horizontal amplitude by the sub |
|
|
|
address WID. Adjust so that the left and right |
|
|
|
white flags of Philips pattern disappear at the |
|
|
|
very limits. |
|
|
|
b. Make the left and right vertical bars straight |
|
|
|
by the sub address DPC. |
|
|
|
c. Compensate the key distortion by the sub |
|
|
|
address KEY. |
|
|
|
d. Again, adjust the sub address WID. |
|
|
|
|
|
|
WG Philips pattern |
1. Conditions:Contrast: Max |
HEIGHT (HIT) |
Visual check of picture |
|
Brightness: Center |
VERT. POSITION |
(Bus control) |
Do not use the Philips |
Color: Center |
|
|
pattern of |
2. Adjustment procedure |
|
|
FRANCESECAM. |
a. By the bus address VPS, adjust V. position so |
|
|
|
that the circle of Philips pattern comes to the |
|
|
|
vertical center. |
|
|
|
b. Adjust HIT so that the upper and lower flags of |
|
|
|
Philips pattern disappear at the very limits. |
|
|
|
|
ROM DATA LIST FOR IIC BUS CONTROL |
|
|
|
(Reference Value) |
|||
|
|
|
|
|
|
|
|
Symbol |
Comment |
|
Data |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2555DB |
2855DB |
|
2552DB |
|
2852DB |
|
|
|
|
|
|
|
|
M00 |
MODE 0 |
51 |
51 |
|
51 |
|
51 |
M01 |
MODE 1 |
33 |
33 |
|
33 |
|
33 |
M01 |
MODE 1 USE ALPS TUNER |
01 |
01 |
|
01 |
|
01 |
M02 |
MODE 2 |
03 |
03 |
|
02 |
|
02 |
M03 |
MODE 3 |
17 |
17 |
|
49 |
|
49 |
HIT |
HEIGHT |
*30 |
*30 |
|
*30 |
|
*30 |
LIN |
V. LINEARITY |
32 |
32 |
|
32 |
|
32 |
VSC |
V. S-CORRECTION |
32 |
32 |
|
32 |
|
32 |
VPS |
V. POSITION |
*07 |
*07 |
|
*07 |
|
*07 |
VCP |
V. COMPENSATION |
30 |
30 |
|
30 |
|
30 |
WID |
H.WIDTH |
*22 |
*26 |
|
*22 |
|
*26 |
DPC |
DPC |
*26 |
*24 |
|
*26 |
|
*24 |
CNR |
DPC CORNER |
P44V32 |
32 |
|
P44V32 |
|
32 |
KEY |
KEYSTONE |
*09 |
*09 |
|
*09 |
|
*09 |
HCP |
H. COMPENSATION |
10 |
10 |
|
10 |
|
10 |
VMC |
V. M-CORRECTION |
52 |
41 |
|
52 |
|
41 |
SHI |
16:9 SUB HEIGHT |
00 |
00 |
|
00 |
|
00 |
SLI |
16:9 SUB V. LINEARITY |
32 |
32 |
|
32 |
|
32 |
SVS |
16:9 SUB V.S-CORRECTION |
17 |
17 |
|
17 |
|
17 |
SDP |
16:9 SUB DPC |
P18V21 |
P17V21 |
|
P18V21 |
|
P17V21 |
SCN |
16:9 SUB CORNER |
30 |
30 |
|
30 |
|
30 |
WCT |
WOOFER FC SET |
12 |
08 |
|
12 |
|
12 |
BAC |
BASS CENTER |
40 |
34 |
|
50 |
|
50 |
TRC |
TREBLE CENTER |
48 |
52 |
|
44 |
|
44 |
BAX |
BASS MAX |
79 |
79 |
|
79 |
|
79 |
WON |
BAZOOKA AUTO |
05 |
30 |
|
06 |
|
06 |
WOF |
BAZOOKA OFF |
20 |
47 |
|
25 |
|
25 |
BAE |
BASS UP |
01 |
03 |
|
01 |
|
01 |
TRE |
TREBLE UP |
12 |
17 |
|
10 |
|
10 |
VOE |
VOL UP |
02 |
02 |
|
00 |
|
00 |
WFL |
WOOFER LEVEL |
100 |
100 |
|
100 |
|
100 |
EMX |
NICAM OFF LEVEL (PHIL) |
252 |
252 |
|
252 |
|
252 |
EMN |
NICAM ON LEVEL (PHIL) |
100 |
100 |
|
100 |
|
100 |
FMA |
FM INPUT ATT (PHIL) |
00 |
00 |
|
00 |
|
00 |
STS |
STEREO SEPARATION |
— |
— |
— |
|
— |
|
|
|
|
|
|
|
|
|
* Mark items should be adjusted.
Block Diagram
Service Mode / Safety Parts / Safety Instructions / Service Adjustments / Adjustment Procedure / Block Diagram
Signal Processing (2555 & 2855) ... Cont’d / Signal Processing (2552 & 2852) ... Cont’d
Power Audio Deflection (2555 & 2855) ... Cont’d / Power Audio Deflection (2552 & 2852) ... Cont’d
TOSHIBA 2555 DB |
3 |
Signal Processing
(2555 & 2855)
Diagram
Service Mode / Safety Parts / Safety Instructions / Service Adjustments / Adjustment Procedure / Block Diagram
Signal Processing (2555 & 2855) ... Cont’d / Signal Processing (2552 & 2852) ... Cont’d
Power Audio Deflection (2555 & 2855) ... Cont’d / Power Audio Deflection (2552 & 2852) ... Cont’d