Teac FT3020, FT3010, FF3010 Hardware Installation Manual
HARDWARE INSTALLATION GUIDE
TAPE
1400
MODEL: FT3020
TABLE
OF
CONTENTS
This Installation Guide
may
be
used for the TAPE1.4GB, TAPE700
COMB0700 units.
PRODUCT WARRANTY
1.
CAUTIONS
2.
TOOLS YOU MAY
3.
KIT DESCRIPTION
4.
,CONNECTIONS, CONTROLS & FUNCTIONS. . . . . . . . . .
5.
BEFORE YOU START . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.
NETWORK OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . .
7.
HARDWARE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . .
8.
CONFIGURING THE FLOPPY DRIVE FOR COMB0700 . .
9.
TAPE LOADING AND EJECTION
10.
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.
RECOMMENDED TAPE MEDIA
......................................
..............................
NEED.
. . . . . . . . . . . . . . . . . . . . . . . . .
................................
.....................
......................
and
.
..
..
..
..
..
..
..
2
2
3
3-4
5
5
6-8
8-9
9
10
11
12.
TECHNICAL
SUPPORT.
. . . . . . . . . . . . . . . . . . . . . . . . . .
..
11
Product Warranty
The user who makes changes or modifies the unit or operating procedures
specified herein without express written
void the warranty .
• Specifications
and
features subject
approval
to
change without notice
by
the manufacturer will
or
obligation.
HARDWARE INSTALLATION GUIDE
HARDWARE INSTALLATION GUIDE
CAUTIONS
1.
The tape drive unit
manner other than specified
2.
NEVER try to open the unit by yourself for inspection or repair. Doing
so may cause damage or
3.
Refer
to
this manual for installation, operation and maintenance proce-
dures.
If
any repairs are required, contact your distributor or dealer from
whom you purchased the unit.
4.
Precautions during placement:
•
When installing the tape drive unit
the LED
on
tape drive unit vertically the LED
above or below the opening for the tape cartridge.
Avoid
placing
heating apparatus;
5.
Do
NOT apply solvents such as thinner, benzene, or alcohol to the
unit, as these may
the drive, wipe off dirt using a soft dust-free cloth.
6.
If
the tape drive unit does not operate normally
properly, contact the representative from whom you purchased the unit
or our
Technical Support number.
or send the unit
packing materials.
7.
Do
NOT
vibrate
is
a precision electronic device.
in
this Installation Guide.
Do
NOT use it
operational failure and will void the warranty.
in
the host computer horizontally,
the front panel will
the
unit
(or
host computer)
place the unit
be
on
the left side. When installing the
on
the front panel can be either
in
direct sunlight or near
in a clean
moisture-free environment.
blemish the surface of the drive. When cleaning
even
after being connected
If
problems arise, and you need to take
to
your place of purchase, please re-use the original
or apply any shocks
to
the drive
(or
the host computer).
in
KIT DESCRIPTION
a
Your tape drive Kit comes complete with:
(1)
Tape
drive unit
(2)
Hardware Installation Guide
(3)
Software Installation Guide
(4)
Registration card
(5)
Arcada backup software program disks for DOS and Windows™
(6)
Tape drive interface data cable
(7)
Mounting screws
(8)
Mounting brackets for mounting
in
a 5 1/4" bay (Included with
TAPE700 Kit and TAPE1.4GB Kit only)
•
Note:
If
all items are not contained
the dealer you purchased
it
from.
in
your
Kit,
please return
it
to
CONTROLS, CONNECTIONS AND FUNCTIONS
TAPE700/
TAPE1.4GB
ON/BUSY indicator LED
Tape cartridge insertion window
"'"
Fig.l
Front View
TOOLS YOU
MAY
NEED
Depending on the design of your computer, you may need the following
tools
to
complete the installation.
o A flat blade screwdriver
o A Phillips screwdriver
o Needle-nosed pliers
-2-
Strap
switch -
Preset
Factory
Please verify
jumpers
are
the
device configuration
set
as
shown
Setting
below.
~~
~~
51
52 53
54 55
Fig.2 Device configuration
The
jumpers
are
preset
at
all
PC
configurations.
any
of
the default settings.
factory for
DO
NOT change
jumpers
Power connector
Rear View Fig.3
-3-
Interface connector
PIN
#1
Loading...