SONY DCR-TRV17E Service Manual

DCR-TRV255E/TRV260/TRV265/TRV265E
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO AND RF SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
SERVO AND RF SYSTEM ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
VIDEO SECTION ADJUSTMENTS
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
SERVICE MODE
DATA PROCESS
ADJUSTMENT REMOTE COMMANDER
SERVICE MODE
RMT-830
Ver 1.0 2003. 11
Revision History
Revision History
Link
Link
Before Starting Adjustments
Before Starting Adjustments
CAMERA SECTION ADJUSTMENTS
CAMERA SECTION ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F PAGE DATA
INITIALIZATION OF 8, A, C, D, E, F, 1C, 1F PAGE DATA
CAMERA SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
LCD SYSTEM ADJUSTMENTS
MECHANISM SECTION ADJUSTMENTS
MECHANISM SECTION ADJUSTMENTS
SECTION 6
ADJUSTMENTS
ADJ
ADJUSTMENT REMOTE COMMANDER
ADJUSTMENT REMOTE COMMANDER
HOW TO ENTER RECORD MODE WITHOUT CASSETTE
HOW TO ENTER RECORD MODE WITHOUT CASSETTE
HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE
HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE
TAPE PATH ADJUSTMENT
TAPE PATH ADJUSTMENT
CHECKS AFTER ADJUSTMENTS
CHECKS AFTER ADJUSTMENTS
9-876-292-51
Sony EMCS Co.
2003K0500-1
©2003.11
Published by DI CS Strategy Div
DCR-TRV255E/TRV260/TRV265/TRV265E

TABLE OF CONTENTS

Section Title Page Section Title Page
6. ADJUSTMENTS
1. Before Starting Adjustments ···········································6-1 1-1. Adjusting Items when Replacing
Main Parts and Boards ···················································· 6-2 6-1. Camera Section Adjustments··········································· 6-4 1-1. Preparations before Adjustments (Camera Section)········6-4 1-1-1.List of Service Tools························································6-4 1-1-2.Preparations ·····································································6-5 1-1-3.Precaution········································································6-6
1. Setting the Switch····························································6-6
2. Order of Adjustments ······················································6-6
3. Subjects ··········································································· 6-6 1-2. Initialization of 8, A, C, D, E, F, 1C, 1F Page Data ········6-7 1-2-1.Version Check··································································6-7
1. Discrimination Method by the Model Name of IC4501
(Mechanism Control) ······················································ 6-7
2. Discrimination Method by Adjusting Remote
Commander ·····································································6-7 1-2-2.Initialization of A, D Page Data ······································6-8
1. Initializing the A, D Page Data········································6-8
2. Modification of A, D Page Data ······································6-8
3. A Page Table····································································6-9
4. D Page Table····································································6-9 1-2-3.Initialization of 8, C, 1C Page Data·······························6-10
1. Initializing the 8, C, 1C Page Data ································6-10
2. Modification of 8, C, 1C Page Data ······························6-10
3. 8 Page Table···································································6-10
4. C Page Table ··································································6-11
5. 1C Page Table ································································6-12 1-2-4.Initialization of E, F, 1F Page Data ·······························6-13
1. Initializing the E, F, 1F Page Data·································6-13
2. Modification of E, F, 1F Page Data ·······························6-13
3. E Page Table ··································································6-13
4. F Page Table ··································································6-14
5. 1F Page Table ································································6-14 1-3. Camera System Adjustments·········································6-15
1. HALL Adjustment ·························································6-15
2. Flange Back Adjustment
(Using the Minipattern Box) ·········································6-16
3. Flange Back Adjustment
(Using the Flange Back Adjustment Chart
and Subject More than 500 m Away) ···························· 6-17 3-1. Flange Back Adjustment (1)··········································6-17 3-2. Flange Back Adjustment (2)··········································6-17
4. Flange Back Check························································6-18
5. Optical Axis Adjustment ···············································6-19
6. Picture Frame Setting ····················································6-20
7. Color Reproduction Adjustment····································6-21
8. LV Standard Data Input ·················································6-22
9. Auto White Balance Standard Data Input ·····················6-22 10 Auto W hite Balance Adjustment···································6-23
11. Auto White Balance Check ··········································· 6-24
12. Steadyshot Check ··························································6-25
13. CCD Defect Check ························································6-25 1-4. LCD System Adjustments ·············································6-26
1. LCD Level Adjustment (PD-204 Board) ······················· 6-26
2. LCD V-COM Adjustment (PD-204 Board) ···················6-27
3. LCD White Balance Adjustment (PD-204 Board) ········6-27 6-2. Mechanism Section Adjustments ··································6-28 2-1. Adjustment Remote Commander ··································6-28 2-2. How to Enter Record Mode without Cassette ···············6-28 2-3. How to Enter Playback Mode without Cassette ············ 6-28 2-4. Tape Path Adjustment····················································6-29 2-4-1.Preparations for Adjustment ··········································6-29 2-4-2.Tape Path Adjustment····················································6-30 2-4-3.No.7 Guide (TG7) Adjustment ······································6-31
2-4-4.CUE, REV Waveforms Check·······································6-31 2-5. Checks After Adjustments ·············································6-31 2-5-1.Waveform Build-up Check ············································ 6-31 2-5-2.Tape Path Check ····························································6-31 6-3. Video Section Adjustments ··········································· 6-32 3-1. Preparations before Adjustments···································6-32 3-1-1.Equipment to Required··················································6-32 3-1-2.Precautions on Adjusting···············································6-33 3-1-3.Adjusting Connectors ····················································6-33 3-1-4.Connecting the Equipment ············································6-33 3-1-5.Alignment Tape ·····························································6-34 3-1-6.Input/output Level and Impedance································6-35 3-2. System Control System Adjustments ····························6-36
1. Initialization of 8, A, C, D, E, F, 1C, 1F Page Data ······6-36
2. Node Unique ID No. Input ············································6-36 2-1. Input of Company ID ···················································· 6-36 2-2. Input of Serial No. ·························································6-36 3-3. Servo and RF System Adjustments ······························· 6-38
1. CAP FG/REEL FG Duty Adjustment (VC-344 Board)·····························································6-38
2. Switching Position Adjustment (VC-344 Board)··········6-38
3. SD Error Rate Check (LP) (VC-344 Board) ·················6-39
3-4. Video System Adjustments············································6-40
1. 27 MHz Origin Oscillation Adjustment (VC-344 Board)·····························································6-40
2. S VIDEO OUT Y Level Adjustment (VC-344 Board)·····························································6-40
3. S VIDEO OUT C Level Adjustment (VC-344 Board)·····························································6-41
4. VIDEO OUT Level Check (VC-344 Board)·················6-42
3-5. Audio System Adjustments ···········································6-43
1. Playback Level Check ···················································6-43
6-4. Service Mode·································································6-44 4-1. Adjustment Remote Commander ··································6-44
1. Using the Adjustment Remote Commander··················6-44
2. Precautions Upon Using the Adjustment Remote Commander ····························6-44
4-2. Data Process ··································································6-45 4-3. Service Mode·································································6-46
1. Setting the Test Mode ····················································6-46
2. Emergence Memory Address ········································6-46
2-1. C Page Emergence Memory Address ····························6-46 2-2. EMG Code (Emergency Code) ·····································6-47 2-3. MSW Codes ·································································· 6-48
3. Bit V alue Discrimination ···············································6-49
4. Switch Check (1) ···························································6-49
5. Switch Check (2) ···························································6-49
6. Switch Check (3) ···························································6-50
7. LED, Video Light, IR Light Check ·······························6-50
8. Record of Use Check·····················································6-51
9. Record of Self-diagnosis Check ····································6-52
* The camera optical axis frame is shown on page 6-53.
The camera color reproduction frame is shown on page 6-54.
— 2 —

1. Before Starting Adjustments

(Machine before starting repair)
(Machine after a board is replaced)
PC PC
Save the EVR data to a personal computer.
Download the saved data to a machine.
EVR Data Re-writing Procedure When Replacing Board
The data that is stored in the repair board, is not necessarily correct.
Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Procedure 1
Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced.
DCR-TRV255E/TRV260/TRV265/TRV265E
SECTION 6

ADJUSTMENTS

Procedure 2
Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board.
Remove the EEPROM and install it.
(Former board)
(New board)
Procedure 3
When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the data from the same model of the same destination, and download it.
(Machine to be repaired) (Machine to be repaired)
PC
Download the data.
After the EVR data is saved and downloaded, chec k the respective items of the EVR data. (Refer to page 6-3 for the items to be checked)
Save the data.
(The same model of the same destination)
6-1
DCR-TRV255E/TRV260/TRV265/TRV265E
t
1-1. Adjusting Items when Replacing Main Parts and Boards
• Adjusting items when replacing main parts
When replacing main parts, adjust the items indicated by z in the following table.
Replaced part
Block replacement
Mounted part replacemen
Adjustment Section Adjustment
Initialization of 8, A, C, D, E, F, 1C, 1F page data Initializing of 8, C, 1C page data
Camera HALL adj. z
LCD LCD level adj. z
System control Node uniqe ID No. input Servo, RF CAP FG/REEL FG duty adj. zz
Video 27 MHz origin osillation adj. zz
Mechanism Tape path adj.
Initializing of A, D page data
Initializing of E, F, 1F page data
Flange back adj. zz Optical axis adj. zz Color reproduction adj. zz LV standard data input zz AWB standard data input zz Auto white balance adj. zz Steadyshot check
LCD V-COM adj. zz LCD White balance adj.
Switching position adj. zz SD error rate check (LP)
S VIDEO OUT Y level adj. zz S VIDEO OUT C level adj.
(LCD panel)
(Fluorescent tube)
(Drum assembly) (Note 1)
(Capstan motor)
(CCD imager)
(Timing generator)
(S/H, AGC, A/D CONV.)
Lens device
Video light (Note 2)
LCD block LCD901
LCD block ND901
Mechanism deck (Note 1)
Mechanism deck M901
Mechanism deck M902
CD-471 board IC951
VC-344 board IC1501, X1501
VC-344 board IC1502
zz z
zz z
zz
zzz
(DV signal process, D/A Converter, Lens control)
(Y/C MIX, Buffer)
(EVR)
(LCD driver)
VC-344 board IC3301
VC-344 board IC6501
VC-344 board IC1601
PD-204 board IC6001
Table 6-1-1 (1)
Note 1: When replacing the drum assy or mechanism deck, reset the data of page: 7, address: A7 to A9.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
Note 2: When replacing the video light, reset the data of page: 7, address: CE and CF.
(Refer to “Record of Use Check” of “6-4. SERVICE MODE”)
6-2
DCR-TRV255E/TRV260/TRV265/TRV265E
• Adjusting items when replacing a board or EEPROM
When replacing a board or EEPROM, adjust the items indicated by z in the following table.
Replaced part
Adjustment Section Adjustment
(COMPLETE)
(COMPLETE)
(EEPROM)
RadarWRadarWRadarW
PD-204 board
VC-344 board
VC-344 board IC4502
Supporting
Initialization of 8, A, C, D, E, F, 1C, 1F page data Initializing of 8, C, 1C page data zz
Camera HALL adj. zzz
LCD LCD level adj. zzzz
System control Node uniqe ID No. input Servo, RF CAP FG/REEL FG duty adj. zzz
Video 27 MHz origin osillation adj. zz
Mechanism Tape path adj.
Initializing of A, D page data
Initializing of E, F, 1F page data
Flange back adj. zzz Optical axis adj. zz Color reproduction adj. zz LV standard data input zzz AWB standard data input zzz Auto white balance adj. zzz Steadyshot check
LCD V-COM adj. zzz LCD White balance adj.
Switching position adj. zzz SD error rate check (LP)
S VIDEO OUT Y level adj. zz S VIDEO OUT C level adj.
zz
zz
zzz
zzz
zz
zzz
zz
Table 6-1-1 (2)
6-3
DCR-TRV255E/TRV260/TRV265/TRV265E
6-1. CAMERA SECTION ADJUSTMENTS

1-1. PREPARATIONS BEFORE ADJUSTMENTS (CAMERA SECTION)

1-1-1. List of Service Tools
• Oscilloscope • Color monitor • Vectorscope
• Regulated power supply • Digital voltmeter • Frequency counter
Ref. No.
J-1
J-2
J-3 J-4 J-5 J-6 J-7 J-8
J-9 J-10 J-11
Filter for color temperature correction (C14) ND filter 1.0
ND filter 0.4 ND filter 0.1 Pattern box PTB-450 Color chart for pattern box Adjustment remote commander (RM-95 upgraded). Siemens star chart Clear chart for pattern box CPC jig connector I/F unit for LANC control Mini pattern box Camera table
Name
Parts Code
J-6080-058-A J-6080-808-A
J-6080-806-A J-6080-807-A J-6082-200-A J-6020-250-A J-6082-053-B J-6080-875-A J-6080-621-A J-6082-539-A J-6082-521-A J-6082-353-B J-6082-384-A
Auto white balance adjustment/check White balance adjustment/check
White balance check White balance check White balance check
For checking the flange back
For connecting the adjustment remote commander For connecting the adjustment remote commander For adjusting the flange back For adjusting the flange back
Usage
J-1 J-2
J-6
J-11
J-7 J-8
J-3
J-4 J-5
J-9 J-10
Fig. 6-1-1
6-4
CN1011
A/V OUT jack
16
1
Audio L (white)
Audio R (red)
Video (yellow)
TV monitor
AC IN
AC adaptor
AC adaptor
CPC lid
I/F unit for LANC control (J-6082-521-A)
Conductor side
L serices Info LITHIUM battery (7.2Vdc)
Adjustment remote commander (RM-95)
CPC jig connector (J-6082-539-A)
LANC jack
AC IN
Terminated at 75
Vector scope
Screw (M2)
1-1-2. Preparations
Note: Before perform the adjustment, check that the data of page:
0, address: 10 is “00”. If not, select page: 0, address: 10, and set data “00”.
1) Connect the equipment for adjustments according to Fig. 6-1-
3.
2) Connect the adjustment remote commander to VC-344 board CN1011 via I/F unit for LANC control (J-6082-521-A) and CPC jig connector (J-6082-539-A). (Fig. 6-1-3) To operate the adjustment remote commander, connect the AC power adaptor to the DC IN jack of I/F unit for LANC control, or connect the L series Info-LITHIUM battery to the battery terminal of I/F unit for LANC control.
DCR-TRV255E/TRV260/TRV265/TRV265E
Pattern box
1 m
Front of the lens
Fig. 6-1-2
Fig. 6-1-3
6-5
DCR-TRV255E/TRV260/TRV265/TRV265E
1-1-3. Precaution
1. Setting the Switch
Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette.
1. POWER switch (SS-5100 block) ..........................CAMERA
2. FOCUS (CF-5100 block) ..................................... MANUAL
3. BACK LIGHT (CF-5100 block) .................................... OFF
4. PROGRAM AE (MENU setting) ................................ AUTO
5. NIGHTSHOT PLUS switch (Lens block) ..................... OFF
6. EXPOSURE (CF-5100 block) .................................... AUTO
2. Order of Adjustments
Basically carry out adjustments in the order given.
Color bar chart (Color reproduction adjustment frame)
H
Yellow
Cyan
Green
AB B
Fig. a (VIDEO terminal of A/V jack output waveform)
A=B
White
Magenta
Red
CD
Blue
A
Enlargement
C=D
Difference in level
7. P EFFECT (MENU setting) ........................................... OFF
8. D ZOOM (MENU setting) ............................................. OFF
9. DEMO MODE (MENU setting) .................................... OFF
10. 16 : 9 WIDE (MENU setting) ........................................ OFF
11. DISPLAY (MENU setting) ............................................ LCD
Electronic beam scanning frame
Red
Cyan
White
Green
Yellow
V
Fig. b (monitor TV picture)
Magenta
Blue
CRT picture frame
B
A
Fig. 6-1-4
3. Subjects
1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 6-1-4. (Color reproduction adjustment frame)
2) Clear chart (Color reproduction adjustment frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time)
3) Chart for flange back adjustment
Join together a piece of white A0 size paper (1189mm × 841 mm) and a piece of black paper to make the chart shown in Fig. 6-1-5.
Note: Use a non-reflecting and non-glazing vellum paper. The
size must be A0 or larger and the joint between the white and black paper must not have any undulations.
Adjust the camera zoom and direction to obtain the output wavef orm shown in Fig. a and the monitor TV display shown in Fig. b.
White
841 mm
Black
1189 mm
Fig. 6-1-5
6-6
DCR-TRV255E/TRV260/TRV265/TRV265E
1-2. INITIALIZA TION OF 8, A, C, D , E, F, 1C, 1F
PAGE DATA
Note: If reading/writing data on pages 1C, 1F, set data: 01 to
page: 0, address: 10, and then select pages C, F. By this data setting, the pages 1C, 1F can be selected. After the data reading/writing finished, return the data on page: 0, address: 10 to “00”.
1-2-1. Version Check
Due to the change of IC4501 (mechanism control), there are two types of versions A and B. The EEPROM data are different according to respecti v e v ersions. Also, the IC4501 version can be checked by a discrimination method by the model name or by the adjusting remote commander. Note 1: Changing the version does not make any changes in sche-
matic diagrams and the rest.
Note 2: Make it sure to confirm the version after replacing
IC4501.
1. Discrimination Method by the Model Name of IC4501 (Mechanism Control)
VC-344 BOARD (SIDE A)
2. Discrimination Method by Adjusting Remote Commander
Version check method:
1) Select page: 3, and address: FF.
2) The version of IC4501 can be checked from the displayed data.
Data Version
01 A 02 B
Data change method:
1) Select page: 0, address: 01, and set data: 01.
2) Select page: 1C, and input the data in the following table.
Note: To write in the non-volatile memory (EEPROM), press the
PAUSE button of the adjustment remote commander each time to set the data.
3) Select page: 0, address: 01, and set data: 00.
Version
Address
D0 40 42
AB
IC4501
154 : A 155 : B
Fig. 6-1-6
6-7
DCR-TRV255E/TRV260/TRV265/TRV265E
1-2-2. Initialization of A, D Page Data Note: Check that the data of page: 0, address: 10 is “00”.
1. Initializing the A, D Page Data Note 1: If “Initialization of Pages A, D” is executed, all data on
pages A, D are initialized. (Only an indi vidual page can­not be initialized)
Note 2: If the A, D page data has been initialized, the following
adjustments need to be performed again.
1) Modification of A, D page data
Note 3: NTSC model: DCR-TRV260/TRV265
PAL model: DCR-TRV255E/TRV265E
Adjustment Page A Adjustment Address 10 to FF Adjustment Page D Adjustment Address 10 to 7F
Initializing method:
Order Page Address Data Procedure
10 0101 20 1000
Set the following data.
37 03
47 0028 57 01 28 Press PAUSE button.
67 02
7
00: NTSC model 80: PAL model
Check the data changes to “01”.
Perform “Modification of A, D Page Data”
2. Modification of A, D Page Data
If the A, D page data has been initialized, change the data of the“Fixed data-2” address shown in the following ta ble by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set data: 01.
2) New data for changing are not shown in the tables because they are different in destination. When changing the data, cop y the data built in the same model. Note 1: If copy the data built in the different model, the
camcorder may not operate.
3) When changing the data, press the PAUSE button of the ad­justment remote commander each time when setting new data to write the data in the non-volatile memory.
4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.
Processing after completing modification A, D page data:
Order Page Address Data Procedure
12 0029 22 01 29 Press PAUSE button.
Note 2: If the following symptoms occur after completing of
the“Modification A, D page data”, check that the data of the “Fixed data-2” addresses of A, D page are same as those of the same model of the same destination.
1) The power is shut off so that unit cannot operate.
6-8
DCR-TRV255E/TRV260/TRV265/TRV265E
3. A Page Table Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the A, D Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of A, D Page Data”)
Address
10 to 19 Fixed data-1 (Initialized data)
1A Fixed data-2
1B to 30 Fixed data-1 (Initialized data)
31 32
33 to 49 Fixed data-1 (Initialized data)
4A Fixed data-2
4B to 4E Fixed data-1 (Initialized data)
4F Fixed data-2
50, 51 Fixed data-1 (Initialized data)
52 53
54 to 64 Fixed data-1 (Initialized data)
65 Fixed data-2
66 to 7F Fixed data-1 (Initialized data)
80 81
82 to 8F Fixed data-1 (Initialized data)
90 Fixed data-2
91 to 96 Fixed data-1 (Initialized data)
97
98
99 to DF Fixed data-1 (Initialized data)
E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF
F0 F1 F2 F3
Initial value
NTSC PAL
Remark
Fixed data-2
Fixed data-2
Fixed data-2
A: Fixed data-2 B: Fixed data-1 (Initialized data) (Refer to “1-2-1. Version Check”.)
Fixed data-2
Address
F4 F5 F6 F7 F8
F9 FA FB FC FD
FE, FF Fixed data-1 (Initialized data)
4. D Page Table Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
Address
10 00 00 Test mode
11 Fixed data-1 (Initialized data)
12
13
14 to 21 Fixed data-1 (Initialized data)
22
23
24 Fixed data-2
25
26
27 to 29 Fixed data-1 (Initialized data)
2A 2B
2C to 35 Fixed data-1 (Initialized data)
36
37 Fixed data-2
38
39 Fixed data-1 (Initialized data) 3A Fixed data-2
3B to 55 Fixed data-1 (Initialized data)
56 Fixed data-2
57 Fixed data-1 (Initialized data)
58 Fixed data-2
59 to 6E Fixed data-1 (Initialized data)
6F Fixed data-2
70 to 7F Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Fixed data-2
the A, D Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of A, D Page Data”)
Initial value
NTSC PAL
Fixed data-2
Fixed data-2
Remark
Remark
6-9
DCR-TRV255E/TRV260/TRV265/TRV265E
1-2-3. Initialization of 8, C, 1C Page Data Note: If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages C. By this data set­ting, the pages 1C can be selected. After the data reading/writing finished, return the data on page: 0, address: 10 to “00”.
1. Initializing the 8, C, 1C Page Data Note 1: If “Initialization of Pages 8, C, 1C” is executed, all data
on pages 8, C, 1C are initialized. (Only an individual page cannot be initialized)
Note 2: If the 8, C, 1C page data has been initialized, the follow-
ing adjustments need to be performed again.
1) Modification of 8, C, 1C page data
2) Electronic viewfinder system adjustments
3) LCD system adjustments
4) Node unique ID No. input
5) Servo, RF system adjustments
6) “S VIDEO OUT Y le v el adjustment” and “S VIDEO OUT C level adjustment” of video system adjust­ments.
Adjustment Page 8 Adjustment Address 00 to FF Adjustment Page C Adjustment Address 10 to FF Adjustment Page 1C Adjustment Address 00 to FF
Initializing method:
Order Page Address Data Procedure
10 0101 20 1000 33 8110 43 80 0C Press PAUSE button.
53 80
6
Check the data changes to “1C”.
Perform “Modification of 8, C, 1C Page Data”
2. Modification of 8, C, 1C Page Data
If the 8, C, 1C page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set data: 01.
2) If modification of data on pages 8, C, set data: 00 to page: 0, address: 10, and then select pages 8, C.
3) If modification of data on pages 1C, set data: 01 to page: 0, address: 10, and then select pages C. After the modification of data finished, return the data on page: 0, address: 10 to “00”.
4) New data for changing are not shown in the tables because they are different in destination. When changing the data, cop y the data built in the same model. Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad­justment remote commander each time when setting new data to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.
Processing after completing modification 8, C, 1C page data:
Order Page Address Data Procedure
10 1000 22 0029 32 01 29 Press PAUSE button.
3. 8 Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 1C Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of 8, C, 1C Page Data”)
Address
00 to AB Fixed data-1 (Initialized data)
AC Fixed data-2
AD to C3 Fixed data-1 (Initialized data)
C4 C5 C6 C7
C8 to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Remark
Fixed data-2
6-10
DCR-TRV255E/TRV260/TRV265/TRV265E
4. C Page Table Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 1C Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of 8, C, 1C Page Data”)
Address
10 EE EE 11 00 00 12 00 00 13 00 00
14, 15 Fixed data-1 (Initialized data)
16 E0 E0 17 E0 E0
18 to 24 Fixed data-1 (Initialized data)
25 86 86 S VIDEO OUT Y level adj. 26 90 90 27 60 60
28 to 2E Fixed data-1 (Initialized data)
2F 0E 0E CAP FG/REEL FG duty adj.
30 to 4D Fixed data-1 (Initialized data)
4E Fixed data-2
4F Fixed data-1 (Initialized data) 50 7C 7C 51 8B 8B 52 89 89 LCD V-COM adj. 53 Fixed data-2 54 Fixed data-1 (Initialized data) 55 Fixed data-2 56 6F 6F 57 4B 4B 58 75 75 LCD level adj. (Contrast adj.)
59 to 5B Fixed data-1 (Initialized data)
5C 5D
5E to 65 Fixed data-1 (Initialized data)
66 Fixed data-2
67 to 74 Fixed data-1 (Initialized data)
75 Fixed data-2
76 to AC Fixed data-1 (Initialized data)
AD Fixed data-2
AE to D2 Fixed data-1 (Initialized data)
D3 D4 D5 D6
D7 to DE Fixed data-1 (Initialized data)
DF Fixed data-2 E0 08 08 E1 00 00 E2 46 46
Initial value
NTSC PAL
Remark
Switching position adj.
CAP FG/REEL FG duty adj.
S VIDEO OUT C level adj.
LCD level adj. (VCO adj.)
LCD White balance adj.
Fixed data-2
Fixed data-2
Node unique ID No. input
Address
E3 01 01 E4 02 02 E5 00 00 E6 00 00 E7 00 00
E8 to F3 Fixed data-1 (Initialized data)
F4 00 00 F5 00 00 F6 00 00 F7 00 00 F8 00 00
F9 00 00 FA 00 00 FB 00 00 FC 00 00 FD 00 00 FE 00 00
FF 00 00
Initial value
NTSC PAL
Remark
Node unique ID No. input
Emergency memory
6-11
DCR-TRV255E/TRV260/TRV265/TRV265E
5. 1C Page Table Note 1: If reading/writing data on pages 1C, set data: 01 to page:
0, address: 10, and then select pages C. By this data set­ting, the pages 1C can be selected. After the data reading/writing finished, return the data on page: 0, address: 10 to “00”.
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the 8, C, 1C Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of 8, C, 1C Page Data”)
Address
00 to 08 Fixed data-1 (Initialized data)
0A to B2 Fixed data-1 (Initialized data)
B3 00 00 B4 00 00 B5 00 00 B6 00 00 B7 00 00 B8 80 80 B9 00 00 BA 00 00 BB 00 00 BC 00 00 BD 00 00 BE 00 00 BF 00 00 C0 00 00 C1 00 00 C2 00 00 C3 80 80 C4 00 00 C5 00 00 C6 00 00 C7 00 00 C8 00 00
C9 to CF Fixed data-1 (Initialized data)
D0 Fixed data-2
D1 to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
09 FF FF Test mode
SD error rate check (LP)
Remark
6-12
DCR-TRV255E/TRV260/TRV265/TRV265E
1-2-4. Initialization of E, F, 1F Page Data Note: Check that the data of page: 0, address: 10 is “00”.
1. Initializing the E, F, 1F Page Data Note 1: If “Initialization of Pages E, F, 1F” is executed, all data
on pages E, F , 1F are initialized. (Only an individual page cannot be initialized)
Note 2: If the E, F, 1F page data has been initialized, the follow-
ing adjustments need to be performed again.
1) Modification of E, F, 1F page data
2) “27 MHz Origin Oscillation Adjustment” of video system adjustments
3) Camera system adjustments
Note 3: NTSC model: DCR-TRV260/TRV265
PAL model: DCR-TRV255E/TRV265E
Adjustment Page E Adjustment Address 00 to FF Adjustment Page F Adjustment Address 10 to FF Adjustment Page 1F Adjustment Address 00 to FF
Initializing method:
Order Page Address Data Procedure
10 0101 20 1000 36 0301
Set the following data, and
46 01
56 02
6
press PAUSE button. 2D: NTSC model 2F: PAL model
Check the data changes to “01”.
Perform “Modification of E, F, 1F Page Data”
2. Modification of E, F, 1F Page Data
If the E, F, 1F page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input.
Modifying method:
1) Before changing the data, select page: 0, address: 01, and set data: 01.
2) If modification of data on pages E, F, set data: 00 to page: 0, address: 10, and then select pages E, F.
3) If modification of data on pages 1F, set data: 01 to page: 0, address: 10, and then select pages F . After the modification of data finished, return the data on page: 0, address: 10 to “00”.
4) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the
camcorder may not operate.
5) When changing the data, press the PAUSE button of the ad­justment remote commander each time when setting new data to write the data in the non-volatile memory.
6) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value.
Processing after completing modification E, F, 1F page data:
Order Page Address Data Procedure
10 1000 22 0029 32 01 29 Press PAUSE button.
3. E Page Table
Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the E, F, 1F Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 1F Page Data”)
Address
00 to 0F Fixed data-1 (Initialized data)
10 Fixed data-2
11 to B0 Fixed data-1 (Initialized data)
B1 Fixed data-2
B2 to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Remark
6-13
DCR-TRV255E/TRV260/TRV265/TRV265E
4. F Page Table Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
the E, F, 1F Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 1F Page Data”)
Address
18, 19 Fixed data-1 (Initialized data)
1A 00 00 1B 60 60
1C to 29 Fixed data-1 (Initialized data)
2A 29 1B 2B 00 00 2C 07 07 2D 00 00 2E 17 0E
36 to 39 Fixed data-1 (Initialized data)
3A 00 00 3B F1 EF
3C, 3D Fixed data-1 (Initialized data)
3E 2A 2B
42, 43 Fixed data-1 (Initialized data)
4A 00 00 4B 00 00 4C 00 00 4D 00 00 4E 2B 2B
Initial value
NTSC PAL
10 80 80 27 MHz origin osillation adj. 11 Fixed data-1 (Initialized data) 12 4A 4A 13 56 56 14 11 11 15 20 20 16 02 02 17 E0 E0
2F 00 00 30 0B 0D 31 00 00 32 Fixed data-1 (Initialized data) 33 22 22 Color reproduction adj. 34 Fixed data-1 (Initialized data) 35 27 24 Color reproduction adj.
3F C0 00 40 59 59 41 00 40
44 28 28 45 EC EC 46 35 35 47 8F 8F 48 13 13 49 B8 B8
Hall adj.
LV standard data input
Auto white balance standard data input
Auto white balance adj.
Color reproduction adj.
Auto white balance adj.
Flange back adj.
Remark
Address
4F 19 19 50 00 00 51 32 32 52 04 04 53 00 00 54 00 00
55 to 59 Fixed data-1 (Initialized data)
5A FF FF Optical axis adj.
5B to 8D Fixed data-1 (Initialized data)
8E
8F Fixed data-2 90
91 to 96 Fixed data-1 (Initialized data)
97 Fixed data-2
98, 99 Fixed data-1 (Initialized data)
9A Fixed data-2
9B to A3 Fixed data-1 (Initialized data)
A4 Fixed data-2
A5 to C4 Fixed data-1 (Initialized data)
C5 C6
C7 to FF Fixed data-1 (Initialized data)
5. 1F Page Table Note 1: If reading/writing data on pages 1F, set data: 01 to page:
Note 2: Fixed data-1: Initialized data. (Refer to “1. Initializing
Address
00 to 7B Fixed data-1 (Initialized data)
7C Fixed data-2
7D to FF Fixed data-1 (Initialized data)
Initial value
NTSC PAL
Flange back adj.
Fixed data-2
0, address: 10, and then select pages F. By this data set­ting, the pages 1F can be selected. After the data reading/writing finished, return the data on page: 0, address: 10 to “00”.
the E, F, 1F Page Data”) Fixed data-2: Modified data. (Refer to “2. Modification of E, F, 1F Page Data”)
Initial value
NTSC PAL
Remark
Remark
6-14

1-3. CAMERA SYSTEM ADJUSTMENTS

Before perform the camera system adjustments, check that the specified values of “27 MHz Origin Oscillation Adjustment”, “S VIDEO OUT Y level Adjustment” and “S VIDEO OUT C level Adjustment” of “VIDEO SYSTEM ADJUSTMENT” are satisf ied. Check that the data of page: 0, address: 10, is “00”. If not, select page: 0, address: 10, and set data “00”
DCR-TRV255E/TRV260/TRV265/TRV265E
1. HALL Adjustment
For detecting the position of lens iris, adjust the hall AMP gain and offset.
Mode CAMERA Subject Not required Measurement Point Displayed data of page: 1 (Note 3) Measuring Instrument Adjusting remote commander Adjustment Page F Adjustment Address 12 to 17 Specified value 87 to 8B during IRIS OPEN
Note 1: Check that the data of page: 0, address: 10 is “00”. Note 2: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 3: The right two digits of the page: 1 displayed data of the
adjusting remote commander.
1:00:
Adjusting method:
Order Page Address Data Procedure
10 0101 26 9489 36 9517 46 01 6D Press PAUSE button. (Note 4)
56 02 66 01 00 Press PAUSE button.
Note 4: The adjustment data will be automatically input to page:
F, address: 12 to 17.
RadarWRadarWRadarW
15 to 19 during IRIS CLOSE
XX
Displayed data
Check the data changes to “01”.
Checking method:
Order Page Address Data Procedure
10 0303 26 01 01 Press PAUSE button.
Check that the displayed data
31
46 01 03 Press PAUSE button.
51
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button. 26 9400 36 9500 40 0300 50 0100
(Note 3) during IRIS OPEN satisfied the specified value.
Check that the displayed data (Note 3) during IRIS CLOSE satisfied the specified value.
6-15
DCR-TRV255E/TRV260/TRV265/TRV265E
2. Flange Back Adjustment
RadarWRadarWRadarW
(Using the Minipattern Box)
The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated dur­ing auto focusing/manual focusing.
Mode CAMERA Subject Siemens star chart with ND filter for
minipattern box (Note 1) Measurement Point Check operation on monitor TV Measuring Instrument Adjustment Page F Adjustment Address 44 to 54
Note 1: Dark Siemens star chart. Note 2: Check that the data of page: 0, address: 10 is “00”. Note 3: Check that the data of page: 6, address: 02 is “00”.
If not, turn the power of unit OFF/ON.
Note 4: Perform the adjustment with the camcorder in horizon-
tal state.
Note 5: Perform “HALL Adjustment” before this adjustment.
Switch setting:
1) NIGHTSHOT PLUS........................................................ OFF
2) DISPLAY (Menu setting) ............................................... LCD
Preparations before adjustments:
1) The minipattern box is installed as shown in the following f ig­ure. Note 6: The attachment lenses are not used.
2) Install the minipattern box so that the distance between it and the front of lens of camcorder is less than 3 cm.
3) Make the height of minipattern box and the camera equal.
4) Check the output voltage of the regulated power supply is the specified voltage ± 0.01 Vdc.
5) Check that the center of Siemens star chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively.
Adjusting method:
Order Page Address Data Procedure
10 0101 26 4801 36 01 13 Press PAUSE button. 46 01 27 Press PAUSE button. (Note 7)
56 02
Check the data changes to “01”.
Note 7: The adjustment data will be automatically input to page:
F, address: 44 to 54.
Processing after completing adjustment:
Order Page Address Data Procedure
16 01 00 Press PAUSE button. 26 01 25 Press PAUSE button. 36 01 00 Press PAUSE button. 46 4800 50 0100
6
Perform “Flange Back Check”.
Specified voltage: The specified voltage varies according to the
minipattern box, so adjust the power supply output voltage to the specified voltage written on the sheet which is supplied with the minipattern box.
Below 3 cm
Minipattern box
Camcorder
Camera
table
Output voltage : Specified voltage ±0.01 Vdc
Red (+)
Black (–) Yellow (SENS +) White (SENS –)
Black (GND)
Regulated power supply
Output current : more than 3.5 A
Need not connected
Fig. 6-1-7
6-16
Loading...
+ 39 hidden pages