Samsung SYNCMASTER 940NPLUS, SYNCMASTER 940N PLUS BLACK, SYNCMASTER 740N PLUS, SYNCMASTER 740N PLUS BLACK Manual

0 (0)

Install driver Install programs

SyncMaster 740NPlus / 940NPlus

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to

the equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Ground to prevent an electric shock

Power

When not used for an extended period of time, set your computer to DPMS.

If using a screen saver, set it to active screen mode.

The images here are for reference only, and are not applicable in all cases (or countries).

Do not use a damaged or loose plug.

z This may cause electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose.

z A bad connection may cause fire.

Do not excessively bend the plug and wire nor place heavy objects upon

them, which could cause damage.

This may cause electric shock or fire.

Do not connect too many extension cords or plugs to one outlet.

z This may cause fire.

Do not disconnect the power cord while using the monitor.

surge may be caused by the separation and may damage the monitor.

Do not use the power cord when the connector or plug is dusty.

If the connector or plug of the power cord is dusty, clean it with a dry

cloth.

Using the power cord with a dusty plug or connector may cause electric

shock or fire.

Installation

Be sure to contact an authorized Service Center, when installing your monitor in

a location with heavy dust, high or low temperatures, high humidity, and exposed

to chemical substances and where it operates for 24 hours such as at airports,

train stations etc.

Failure to do so may cause serious damage to your monitor.

Place your monitor in a location with low humidity and a minimum of

dust.

Failure to do so may cause electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or the person carrying it.

Install the monitor base in a showcase or shelf so that the end of the

base does not protrude from the showcase or shelf.

Dropping the product may cause damage to the product or the person

carrying it.

Do not place the product on an unstable or small surface area.

Place the product on an even and stable surface, as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

z Take care, as someone, specifically children may trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes

away from the product.

z Otherwise, this may cause fire.A melted coating may cause electric

shock or fire.

Keep any heating devices away from the power cable.

A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a

bookshelf, closet, etc.

Any increase in the internal temperature may cause fire.

Put down the monitor carefully.

Failing to do so may damage the monitor.

Do not place the monitor face down.

This may damage the TFT-LCD surface.The installation of the bracket

must be done by a qualified professional.

Installing a wall bracket must be done by a qualified professional.

Installing the bracket by unqualified personnel may result in injury.

Always use the mounting device specified in the owner's manual.

When installing the product, make sure to keep it away from the wall

(more than 10 cm/4 inches) for ventilation purposes.

Poor ventilation may cause an increase in the internal temperature of the

product, resulting in a shortened component life and degraded

performance.

Keep the plastic packaging (bag) out of children's reach.

z The plastic packaging (bag) may cause suffocation if children play with

it.

Clean

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with

a slightly moistened, soft fabric.

Do not spray water or detergent directly onto the monitor.

z This may cause damage, electric shock or fire.

Use the recommended detergent with a smooth cloth.

If the connector between the plug and the pin is dusty or dirty, clean it

properly using a dry cloth.

A dirty connector may cause electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

z Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using

a soft, dry cloth.

z Do not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact the SAMSUNG customer care center or Customer Center for

interior cleaning once a year.

Keep the product's interior clean. Dust which has accumulated in the

interior over an extended period of time may cause a malfunction or fire.

Others

Do not remove the cover (or back).

This may cause electric shock or fire.

Refer to a qualified servicing company.

If your monitor does not operate normally - in particular, if there is any

unusual sound or smell coming from the monitor - unplug it immediately

and contact an authorized dealer or the Service Center.

This may cause electric shock or fire.

Keep the product away from places exposed to oil, smoke or moisture;

do not install inside a vehicle.

z This may cause a malfunction, electric shock or fire.

In particular, avoid operating the monitor near water or outdoors where

the monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off

and unplug the power cord. Then contact the Service Center .

z The monitor may malfunction, causing electric shock or fire.

Disconnect the plug from the outlet during storms or lightning or if it is

not used for a long period of time.

z Failure to do so may cause electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal

cable.

This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not move the monitor right or left by pulling only the wire or the

signal cable.

This may cause a breakdown, electric shock or fire due to damage to

the cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects

on the monitor.

This may cause a malfunction, electric shock or fire.

If a foreign substance enters the monitor, unplug the power cord and

contact the Service Center.

Keep the product away from combustible chemical sprays or

inflammable substances.

This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or

inflammable objects such as paper or matches into the vent, headphone

port or AV ports or etc.

z This may cause electric shock or fire. If an alien substances or water

enters the product, turn the product off, unplug the power connector

from the wall outlet and contact the Service Center.

When viewing a fixed screen for an extended period of time, residual

image or blurriness may appear.

z Change the mode to energy saving mode or set a screensaver to a

changing picture when away from the monitor for an extended period of

time.

Adjust the resolution and frequency to the level appropriate for the

model.

An inappropriate resolution may cause undesirable picture quality.

17,19 inch (43, 48 cm) - 1280 X 1024

Viewing the monitor continuously at a too close angle may result in

damage to your eyesight.

To ease eye strain, take at least a five-minute break after every hour of

using the monitor

Do not install the product on an unstable, uneven surface or a location

prone to vibrations.

Dropping the product may cause damage to the product or the person

carrying it. Using the product in a location prone to vibrations may

shorten the lifetime of the product or may cause the product to catch fire.

When moving the monitor, turn off and unplug the power cord.

Make sure that all cables, including the antenna cable and cables

connected to other devices, are disconnected before moving the

monitor.

Failure to disconnect cables may damage it and cause fire or electric

shock.

Place the product out of children's reach, as they could damage by

hanging onto it.

z A falling product may cause injury to the person or even fatality.

When not using the product for an extended period of time, keep the

product unplugged.

Otherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, causing electric shock or fire.

Do not place your children's favorite toys or any other objects of interest

on the product.

Children may try to climb on the product to retrieve an object. The

product could fall, causing injury or even fatality.

When lifting up or moving the monitor, do not lift the monitor upside

down while holding only the stand.

z This may cause your monitor to fall, and become damaged or cause

personal injury.

Good Postures When Using the Monitor

Try to maintain a good posture when using the monitor.

Keep your back straight.

Keep a distance of about 45 ~ 50 cm between your eyes and

the monitor screen. Look at the screen from slightly above it,

and have the monitor directly in front of you.

z Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor

height so that the top of the monitor is slightly below eye level.

Adjust the monitor angle so that there is no reflected light on

the screen.Try to maintain your arms perpendicular to your

armpits.

Keep your arms level with the back of your hands.

Keep the angle of the elbow perpendicular.

Keep the angle of the knees at more than 90 degree. Do not let

your feet fall up from the floor. Adjust the arm position so that it

is below the heart.

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local deale

to bu

tional items.

Unpacking

Without stand

Monito

With stand

Monitor & Sim

le stand Bottom

MagicRotation program can not be provided as Simple

Stand does not support Pivot function.

Monitor & Pivot stand

Monitor & Slidin

Stand

Monitor & Lowest HAS Stand

Manual

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software

icRotation software

Cable

D-sub Cable Power Cord

Front

MENU button [ ]

Opens the OSD menu. Also use to exit the OSD menu or return to

the previous menu.

MagicBright™

[]

MagicBright™ is a new feature providing optimum viewing

environment depending on the contents of the image you are

watching. Currently seven different modes are available: Custom,

Text, Internet, Game, Sport and Movie, Dynamic Contrast. Each

mode has its own pre-configured brightness value. You can easily

select one of seven settings by simply pressing MagicBright™

control button.

1) Custom

Although the values are carefully chosen by our engineers, the

pre-configured values may not be comfortable for your eyes

depending on your taste.

If this is the case, adjust the brightness and contrast by using

the OSD menu.

2) Text

For documentations or work involving a lo t of text .

3) Internet

For working with a mixture of images such as texts and

graphics.

4) Game

For watching motion pictures such as a game.

5) Sport

For watching motion pictures such as a sport.

6) Movie

For watching motion pictures such as a DVD or Video CD.

7) Dynamic Contrast

Dynamic Contrast is to automatically detect distribution of

inputted visual signal and adjust to create optimum contrast.

>>Click here to see an animation clip

Brightness

button

[]

When OSD is not on the screen, push the button to adjust brightness.

Adjust buttons [

Adjust items in the menu.

]

Enter button [ ]

Activates a highlighted menu item.

AUTO button

Use this button for auto adjustment.

Power button [ ]/

Power indicator

Use this button for turn the monitor on and off. /

This light glows blue during normal operation, and blinking blue once

as the monitor saves your adjustments.

See PowerSaver described in the manual for further information regarding power saving

functions. For energy conservation, turn your monitor OFF when it is not needed, or when

leaving it unattended for long periods.

Rear

Simple stand Pivot stand / Sliding Stand / Lowest HAS Stand

(The configuration at the back of the monitor may vary from product to product.)

POWER port

Connect the power cord for your monitor to the power port on the back

of the monitor.

RGB IN port

Connect the signal cable to the 15-pin, D-sub port on the back of your

monitor.

POWER on/off Switch

(

tion

)

Use this button for turn the monitor on and off.

Kensington Lock

The Kensington lock is a device used to physically fix the system to

something when using it in a public place. (The locking device has to

be purchased separately.) For using a locking device, contact the

place of purchase.

See Connecting the Monitor for further information regarding cable connections.

Connecting the Monitor

Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor into a nearby outlet.

Use appropriate connection for your computer.

Using the D-sub (Analog) connector on the video card.

Connect the signal cable to the 15-pin, D-sub port on the back of your monitor.

[ RGB IN ]

Connected to a Macintosh.

Connect the monitor to the Macintosh computer using the D-sub connection cable.

If the monitor and the computer are connected, you can turn them on and use them.

Using the Stand

Monitor Assembl

Monitor and Bottom

Pivot Stand / Slidin

Stand

Stand Stopper

Attaching a Base

This monitor accepts a 75 mm x 75 mm VESA-compliant mounting interface pad.

Simple stand

Pivot stand

Sliding Stand

Lowest HAS Stand

Monitor

Mounting interface pad (Sold separately)

1. Turn off your monitor and unplug its power cord.

2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the

screen.

3. Remove four screws and then remove the stand from the LCD monitor.

4. Align the mounting interface pad with the holes in the rear cover mounting Pad and secure it

with four screws that came with the arm-type base, wall mount hanger or other base.

Installing the Monitor Driver (Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating

system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown

below.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)

http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

1. Insert CD into the CD-ROM drive.

2. Click

"Windows"

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. If you can see following message window, then click the

"Continue Anyway"

button.

Then click

"OK"

button. (Microsoft

Windows

XP Operating System)

5. Monitor driver installation is completed.

This monitor driver is under certifying MS logo,and this installation don't

damage your system.The certified driver will be posted on Samsung

Monitor homepage

http://www.samsung.com/.

Installing the Monitor Driver (Manual)

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating

system to another. Follow the directions appropriate for the operating system you

have.

Prepare a blank disk and download the driver program file at the Internet web site shown

below.

Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)

http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

Microsoft

Windows Vista™ Operating System

1. Insert your Manual CD into your CD-ROM drive.

Click (Start) and "

Control Panel

". Then, double-click on "

Appearance and

Personalization

3. Click "

Personalization

" and then "

Display Settings

4. Click "

Advanced Settings…

5. Click "

Properties

" in the "

Monitor

" tab. If the "

Properties

" button is deactivated, it

means the configuration for your monitor is completed. The monitor can be used as is.

If the message “

Windows needs…

” is displayed, as shown in the figure below,

click "

Continue

This monitor driver is under certifying MS logo, and this installation doesn't

damage your system.

The certified driver will be posted on Samsung Monitor homepage

http://www.samsung.com/

Click "

Update Driver…

" in the "

Driver

" tab.

+ 40 hidden pages