Samsung LTM405W, SyncMaster 400T, PC40PS Service Manual

LCD-TV

Chassis Model
AL29NO LTM295W
AL40NO LTM405W

Manual

SERVICE

LCD-TV CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

11. Panel Description

CONFIDENTIAL

1-1-1 Warnings

1. For continued safety, do not attempt to modify the
circuit board.

2. Disconnect the AC power and DC Power Jack
before servicing.

1-1-2 Servicing the LCD Monitor

1. When servicing the LCD Monitor disconnect the
AC line cord from the AC outlet.

2. It is essential that service technicians have an
accurate voltage meter available at all times. Check
the calibration of this meter periodically.

1-1-3 Fire and Shock Hazard

Before returning the monitor to the user, perform the
following safety checks:

1. Inspect each lead dress to make certain that the
leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in
the monitor.

2. Inspect all protective devices such as nonmetallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.

3. Leakage Current Hot Check (Figure 1-1):

WARNING:
Do not use an isolation transformer during this test.

Use a leakage current tester or a metering system
that complies with American National Standards
Institute (ANSI C101.1, Leakage Current for

Appliances), and Underwriters Laboratories (UL
Publication UL1410, 59.7).

Figure 1-1. Leakage Current Test Circuit

4. With the unit completely reassembled, plug the AC
line cord directly into a 120V AC outlet. With the
unit’s AC switch first in the ON position and then
OFF, measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including: metal cabinets,
screwheads and control shafts. The current
measured should not exceed 0.5 milliamp. Reverse
the power-plug prongs in the AC outlet and repeat

the test.

1-1-4 Product Safety Notices

Some electrical and mechanical parts have special
safety-related characteristics which are often not
evident from visual inspection. The protection they give
may not be obtained by replacing them with
components rated for higher voltage, wattage, etc. Parts
that have special safety characteristics are identified by

on schematics and parts lists. A substitute
replacement that does not have the same safety
characteristics as the recommended replacement part
might create shock, fire and / or other hazards. Product
safety is under review continuously and new
instructions are issued whenever appropriate.

LTM295W/LTM405W 1-1

CONFIDENTIAL

1 Precautions

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.

1-1 Safety Precautions

DEVICE
UNDER
TEST

TEST ALL

EXPOSED METAL

SURFACES

(READING SHOULD

NOT BE ABOVE 0.5mA)

LEAKAGE
CURRENT

TESTER

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED
(USING AC ADAPTER
PLUG AS REQUIRED)

EARTH

GROUND

!

1-2-1 General Servicing Precautions

1. Always unplug the unit’s AC power cord from the
AC power source and disconnect the DC Power
Jack before attempting to:
(a) remove or reinstall any component or assembly,
(b) disconnect PCB plugs or connectors, (c) connect
a test component in parallel with an electrolytic
capacitor.

2. Some components are raised above the printed
circuit board for safety. An insulation tube or tape
is sometimes used. The internal wiring is
sometimes clamped to prevent contact with
thermally hot components. Reinstall all such
elements to their original position.

3. After servicing, always check that the screws,
components and wiring have been correctly
reinstalled. Make sure that the area around the
serviced part has not been damaged.

1. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known earth
ground. Alternatively, wear a discharging wrist­strap device. To avoid a shock hazard, be sure to
remove the wrist strap before applying power to
the monitor.

2. After removing an ESD-equipped assembly, place it
on a conductive surface such as aluminum foil to
prevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These can
generate electrical charges sufficient to damage
ESDs.

4. Use only a grounded-tip soldering iron to solder or
desolder ESDs.

5. Use only an anti-static solder removal device. Some
solder removal devices not classified as “anti-static”
can generate electrical charges sufficient to damage
ESDs.

4. Check the insulation between the blades of the AC
plug and accessible conductive parts (examples:
metal panels, input terminals and earphone jacks).

5. Insulation Checking Procedure: Disconnect the
power cord from the AC source and turn the power
switch ON. Connect an insulation resistance meter
(500 V) to the blades of the AC plug.

The insulation resistance between each blade of the
AC plug and accessible conductive parts (see
above) should be greater than 1 megohm.

6. Always connect a test instrument’s ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrument’s
ground lead last.

6. Do not remove a replacement ESD from its
protective package until you are ready to install it.
Most replacement ESDs are packaged with leads
that are electrically shorted together by conductive
foam, aluminum foil or other conductive materials.

7. Immediately before removing the protective
material from the leads of a replacement ESD,
touch the protective material to the chassis or
circuit assembly into which the device will be
installed.

Caution: Be sure no power is applied to the

chassis or circuit and observe all
other safety precautions.

8. Minimize body motions when handling
unpackaged replacement ESDs. Motions such as
brushing clothes together, or lifting your foot from
a carpeted floor can generate enough static
electricity to damage an ESD.

1 Precautions

1-2 LTM295W/LTM405W

CONFIDENTIAL

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect
transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions

section of this manual.

Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the

safety precautions, always follow the safety precautions.

CONFIDENTIAL

2 Product Specifications

2-1 Specifications

LCD Panel

TFT-LCD panel, RGB vertical stripe, normally black TFT-LCD panel, RGB vertical stripe, normally black
transmissive, (29 -Inch) viewable, 0.4935 mm pixel pitch

transmissive, (40-Inch) viewable, 0.6735 mm pixel pitch

Scanning Frequency Horizontal : 30 KHz ~ 60 KHz

Vertical : 56 Hz ~ 75 Hz
Display Colors 16,777,216 Million colors
Maximum Resolution Horizontal : 1280 Pixels

Vertical : 768 Pixels
Input Video Signal Analog, 0.7 Vp-p ± 5% positive at 75 Ω,

internally terminated
Input Sync Signal Type : Seperate H/V sync, Composite H/V, Sync-on-Green

Level : TTL level
AC power voltage & Frequency AC 90 ~ 240V 60 Hz/50 Hz ± 3 Hz, DC 28V / 8A
Power Consumption 160W (max) 220W (max)
Dimensions

Unit (W x D x H)

29.9 x 7.7 x 22.4 Inches (759.6 x 195.0 x 568.5 mm)

39.6 x 11.8 x 29.4 Inches (1006.0 x 300.0 x 746.5 mm)

Carton (W x D x H)

37.8 x 7.7 x 22.4 Inches (961.2 x 195.0 x 568.5 mm)

49.1 x 11.8 x 29.4 Inches (1247.6 x 300.0 x 746.5 mm)
Weight (Net / Gross)
Environmental Considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C)

Humidity : 10 % ~ 80 %
Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)

Humidity : 5 % ~ 95 %

TV System

Sound Characteristics •Max Internal speaker Out : Right c 10 W / Leftc 10 W

•Bass control Range : -6 ± -12dB ~ +6 ± 12dB

•TREBLE control Range : -10 ± -12dB ~ +10 ± 12dB

•Output frequency : RFc 80 Hz~15 KHz /A/Vc 80 Hz~20 KHz

•Line out : RFc 80 Hz~15 KHz /A/Vc 80 Hz~20 KHz

•SyncMaster LTM295W/LTM405W comply with SWEDAC (MPRII) recommendations for reduced electromagnetic fields.

•Designs and specifications are subject to change without prior notice.

LTM295W/LTM405W 2-1

Item

Description

LTM295W

LTM405W

18.0 kg (39.682 lbs) 28.0 kg ( 61.715 lbs)

Antena Input 75Ω, Coaxial Cable

Color NTSC-M

Sound BTSC, A2 STEREO, EIAJ

CONFIDENTIAL

2-2 Pin Assignments

Pin No.

30 Pin Signal Cable (DVI Analog)

Pin No.

30 Pin Signal Cable (DVI Analog)

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15

16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

RX2+
RX2­GND
RX1+
RX1­GND
RX0+
RX0­GND
RXC+
RXC­GND
DDC (Clock)
DDC (Data)
GND

GND
Check • D-Sub
GND
DDC_5V
DDC_5V
GND
V/Sync
GND
H/Sync
GND
Blue
GND
Green
GND
Red

CONFIDENTIAL

2 Product Specifications

LTM295W/LTM405W 2-3

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standard
for computer-generated video signals.

48.1

1040

120

64

800

56

72.2
666

6

23

600

37

50.000

Positive
Positive

Separate

37.9

1056

128

88

800

40

60.3
628

4

23

600

1

40.000

Positive
Positive

Separate

35.2

1024

72
128
800

24

56.3
625

2

22

600

1

36.000

–/+
–/+

Separate

SVGA/56 Hz

800 x 600

SVGA/60 Hz

800 x 600

SVGA/72 Hz

800 x 600

MAC/66 Hz

640 x 480

35.0
864

64
96

640

64

66.7
525

3

39

480

3

30.240

Negative
Negative
Separate

44.955
1650

40
70

1280

260

59.94
750

5

20

720

5

74.176

–/+
–/+

Separate

fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Freq.
(MHz)

Polarity
H.Sync

V.Sync
Remark

VGA3/60 Hz

640 x 480

VGA/72 Hz
640 x 480

VGA/75 Hz
640 x 480

VGA/85 Hz
640 x 480

MAC/60 Hz

640 x 480

DTV/

59.94 Hz

1280 x 720

DTV/

59.94 Hz

1920 x 1080

Table 2-1 Timing Chart

33.716
2200

44
44

1920

192

59.94
1125

15

2

1080

5

74.176

–/+
–/+

Separate

31.5
800

96
40

640

8

60.0
525

2

25

480

2

25.175

Negative
Negative
Separate

37.9
832

40
120
640

16

72.8
520

3

20

480

1

31.500

Negative
Negative
Separate

37.5
840

64
120
640

16

75.0
500

3

16

480

1

31.500

Negative
Negative
Separate

43.3
832

56
80

640

56

85.0
509

3

25

480

1

36.000

Negative
Negative
Separate

31.5
800

96
48

640

16

60.0
525

2

33

480

10

25.175

Negative
Negative
Separate

Mode

Timing

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

CONFIDENTIAL

2 Product Specifications

2-4 LTM295W/LTM405W

68.7

1456

128
144

1152

32

75.1
915

3

39

870

3

100.000

Negative
Negative
Separate

67.5

1600

128
256

1152

64

75.0
900

3

32

864

1

108.000

Positive
Positive

Separate

60.2

1328

96

176

1024

32

74.9
804

3

30

768

3

80.000

Negative
Negative
Separate

MAC/74 Hz
1024 x 768

VESA/75 Hz
1152 x 864

MAC/75 Hz

1152 x 870

MAC/60 Hz

1024 x 768

48.8

1312

96

128

1024

64

60.0
813

6

33

768

6

64.000

Negative
Negative
Separate

46.9

1056

80
160
800

16

75.0
625

3

21

600

1

49.500

Positive
Positive

Separate

fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Freq.
(MHz)

Polarity
H.Sync

V.Sync
Remark

MAC/74 Hz

832 x 624

XGA/60 Hz
1024 x 768

XGA/70 Hz
1024 x 768

XGA/75 Hz
1024 x 768

XGA/85 Hz
1024 x 768

SVGA/75 Hz

800 x 600

SVGA/85 Hz

800 x 600

Table 2-2 Timing Chart (continued)

53.7

1048

64
152
800

32

85.1
631

3

27

600

1

56.250

Positive
Positive

Separate

49.7

1152

64
224
832

32

74.6
667

3

39

624

1

57.284

Negative
Negative
Separate

48.4

1344

136
160

1024

24

60.0
806

6

29

768

3

65.000

Negative
Negative
Separate

56.5

1328

136
144

1024

24

70.1
806

6

29

768

3

75.000

Negative
Negative
Separate

60.0

1312

96

176

1024

16

75.0
800

3

28

768

1

78.750

Positive
Positive

Separate

68.7

1376

96

208

1024

48

85.0
808

3

36

768

1

94.500

Positive
Positive

Separate

Mode

Timing

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

CONFIDENTIAL

2 Product Specifications

LTM295W/LTM405W 2-5

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Frequency
(MHz)

Polarity
H.Sync

V.Sync
Remark

SUN/76 Hz

1280 x 1024

SXGA/60 Hz
1280 x 1024

SUN/76 Hz
1152 x 900

71.7

1472

96

208

1152

16

76.0
943

8

33

900

2

105.561

Negative
Negative
Separate

SUN/66 Hz

1152 x 900

61.8

1528

128
208

1152

40

66.0
937

4

31

900

2

94.500

–/+
–/+

Separate

64.0

1688

112
248

1280

48

60.0

1066

3

38

1024

1

108.000

Positive
Positive

Separate

74.4

1680

160
208

1280

32

70.0

1063

3

36

1024

0

125.000

Negative
Negative
Separate

80.0

1688

144
248

1280

16

75.0

1066

3

38

1024

1

135.000

Positive
Positive

Separate

81.1

1664

64

288

1280

32

76.1

1066

8

32

1024

2

135.000

Negative
Negative
Separate

SXGA/75 Hz

1280 x 1024

78.1

1728

192
192

1280

64

72.0

1085

3

55

1024

3

135.000

Negative
Negative
Separate

HP/72 Hz

1280 x 1024

NCD/70 Hz

1280 x 1024

Table 2-3 Timing Chart (continued)

Mode

Timing

CONFIDENTIAL

2 Product Specifications

2-6 LTM295W/LTM405W

QRS

P

O

Video

Sync

Sync

Horizontal

Vertical

CDE

P

O

B

A

Video

Sync

Sync

Separate Sync

C D

A

O

E

B

P

Video

Sync

Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width
C : Back porch D : Active time Q : Back porch R : Active time
E : Front porch S : Front porch

Table 2-4 Timing Chart (continued)

fH (kHz)
A µsec
B µsec
C µsec
D µsec
E µsec
fV (Hz)
O msec
P msec
Q msec
R msec
S msec
Clock

Frequency
(MHz)

Polarity
H.Sync

V.Sync
Remark

UXGA/70Hz
1600 x 1200

UXGA/65Hz
1600 x 1200

81.25
2160

192
304

1600

64
65

1250

3

46

1200

1

175.500

–/+
–/+

Separate

UXGA/60Hz
1600 x 1200

75

2160

192
304

1600

64
60

1250

3

46

1200

1

162.000

–/+
–/+

Separate

87.5

2160

192
304

1600

64
70

1250

3

46

1200

1

189.000

–/+
–/+

Separate

80.038
2124

160
308

1600

56

64.443
1242

3

38

1200

1

170.000

–/+
–/+

Separate

74.52
2592

208
336

1920

128

60

1242

3

38

1200

1

193.156

Negative

Positive

Separate

WUXGA2/60 Hz

1920 x 1200

89.286
2240

256
368

1600

16

66.931
1334

10
44

1200

80

200.000

–/+
–/+

Separate

SUN/66 Hz

1600 x 1200

NCD/64Hz

1600 x 1200

Mode

Timing

CONFIDENTIAL

2 Product Specifications

LTM295W/LTM405W 2-7

Table 2-5 DTV Timing chart

Timing No.
Originator
Mode Name
Resolution (HxV)

1
274M
1080i/60iHz
1920x1080

2
296M

720p/60Hz

1280x720

3
293M
480p/60Hz
720x483

HORIZONTAL
Frequency
Total time
Border (L / R)
Data time
Front porch
Sync. width
Back porch
Sync. polarity

33.750kHz

29.630

µs

0.000

µs

25.859

µs

0.593

µs

0.593

µs

2.586

µs

-

-

45.000kHz

22.222

µs

0.000

µs

17.239

µs

0.943

µs

0.539

µs

3.502

µs

-

31.469kHz

31.778

µs

0.000

µs

26.667

µs

0.593

µs

2.333

µs

2.185

µs

-

VERTICAL
Frequency
Total time
Border (T / B)
Data time
Front porch
Sync. width
Back porch
Sync. polarity

30Hz

33.333ms

0.000ms

0.059ms

0.148ms

0.444ms

-

60Hz

16.667ms

0.000ms

16.000ms

0.111ms

0.111ms

0.444ms

-

60Hz

16.683ms

0.000ms

15.349ms

0.191ms

0.191ms

0.953ms

-

Dot Clock 75MHz 75MHz 27MHz

2-4 DTV Timing Chart

Memo

2 Product Specifications

2-8 LTM295W/LTM405W

CONFIDENTIAL

LTM295W/LTM405W 3-1

CONFIDENTIAL

3 Disassembly and Reassembly

This section of the service manual describes the disassembly and reassembly procedures for the
LTM295W/LTM405W monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling

these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.

2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.

1. Remove 4 screws of the cover rear.

2. Remove the stand from LCD-TV.

3 Disassembly and Reassembly

3-2 LTM295W/LTM405W

CONFIDENTIAL

3. Remove 4 screws of the cover rear.

4. Pull the cover rear.

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

CONFIDENTIAL

LTM295W/LTM405W 4-1

4 Alignments and Adjustments

This section of the service manual explains how to use the DDC JIG to adjust the black, red, green, and blue
levels of the FPD when you replace the AD Board, and how to update the microprocessor when you
change the Panel or Lamp(s).

4-1 General Alignment Instuction

1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation.
Check the basic characteristics such as height, horizontal and vertical sync.

2. Use the specified test equipment or its equivalent.

3. Correct impedance matching is essential.

4. Avoid overload. Excessive signal from a sweep generator might overload the front-end
of the TV. When inserting signal markers,do not allow the marker generator to distort
test result.

5. Connect the TV only to an DC power source with voltage and frequency as specified on
the backcover nameplate.

6. Do not attempt to connect or disconnect any wire while the TV is turned on. Make sure
that the power cord is disconnected before replacing any parts.

7. To protect aganist shock hazard,use an isolation transform.

Memo

4 Alignments and Adjustments

4-2 LTM295W/LTM405W

CONFIDENTIAL

CONFIDENTIAL

LTM295W/LTM405W 5-1

5 Troubleshooting

29”:Does proper DC 28 V appear

at DC jack connected to CN28?

40”:Does proper DC 28 V appear

at DC jack connected to CN29?

Check SMPS PCB and Adapter.

Yes

No

Does proper DC 5 V appear at

Pin 17 of CN201?

Check CN201 and related circuit.

Check IC963, IC906 and IC905.

Yes

No

Does proper DC 3.3 V

appear at Pin 2 of IC953,

IC954, IC956 and IC957?

Check IC953, IC954, IC956 and IC957

.

Yes

No

Does proper DC 2.5 V appear at

Pin 2 of IC961 and IC964?

Check IC961 and IC964.

Yes

No

Does proper DC 5 V appear at

Pin 2 of

IC952, IC955 and IC 958

?

Check IC952, IC955 and IC 958.

Yes

No

5-1 No Power

CONFIDENTIAL

5 Troubleshooting

5-2 LTM295W/LTM405W

5-2 No Video (CVBS, S-Video)

Power indicator is green

Does the signal appear at

Pin 5, 9, 11 and 36 of IC1?

Check IC1.

Yes

No

Does the clock pulse appear at

Pin 6, 13 and Pin 69, 70 of IC302?

Check IC302 and related circuit.

Yes

No

Does the colck pluse

appear at R812, R813 and

H/V Sync pulse of IC801?

Check related circuit of IC801.

Yes

No

Replace LCD Panel.

CONFIDENTIAL

5 Troubleshooting

LTM295W/LTM405W 5-3

5-3 No Picture (PC Signal [Analog])

Check Pin 22 and 24 of CN201.

Check CN201 and related circuit.

Yes

No

Check Pin 66 and 67 of CN203.

Check IC203 and related circuit.

Yes

No

Does the colck pluse

appear at R619, R621 and

H/V Sync pulse of IC603?

Check IC603 and related circuit.

Yes

No

IC901 and IC903 and replace it.

CONFIDENTIAL

5 Troubleshooting

5-4 LTM295W/LTM405W

Does the signal appear at

Pin 47, 48, 50, 51, 53, 54, 56,

57 and 67 of IC503?

Check IC503 and related circuit.

Yes

No

Check Pin 10 and 13 of IC504?

Check IC504 and related circuit Q501.

Yes

No

Does the signal appear at

L502, L503, L504 and L505?

Replace L502, L503, L504 and L505.

Yes

No

29”:Check Speaker and CN2.
40”:Check Speaker and CN2.

5-4 No Sound (RF, PC, Video, Component)

CONFIDENTIAL

5 Troubleshooting

LTM295W/LTM405W 5-5

5-5 No Picture (DTV)

29”:Does the signal appear at

Pin 16, 18 and 20 of CN103?

40”:Does the signal appear at

Pin 16, 18 and 20 of CN3?

Check related circuit and
input signal of connector.

Yes

Yes

No

Dose the signal appear at

Pin 43, 48 and 54 of IC404?

Check IC404 and related circuit.

Yes

No

Dose the signal appear at

Pin 15, 19 and 21 of IC403?

Check IC403 and related circuit.

Yes

No

Check IC801 and related circuit.

Power inductor is green.

Memo

5 Troubleshooting

5-6 LTM295W/LTM405W

CONFIDENTIAL

CONFIDENTIAL

LTM295W/LTM405W 6-1

6 Exploded View and Parts List
6-1 LTM295W

6-2 LTM405W

6 Exploded View & Parts List

6-2 LTM295W/LTM405W

CONFIDENTIAL

Item󰼿No󰼿󰼿󰼿󰼿 Design󰼿LOC 󰼿󰼿품󰼿󰼿󰼿󰼿󰼿명󰼿󰼿 󰼿󰼿󰼿󰼿Spec󰼿󰼿󰼿󰼿󰼿 SERVICE
LTM295WX/XAA
RE-LTM295WX/XAA 󰼿- 1 TORISAN,WX-71N31 󰼿­BN90-00281A 󰼿- ASSY󰼿STAND AL29UO,U.S.A SNA
6003-001310 C/R+STAND SCREW-TAPTITE BH,+,B,M4,L16,ZPC(BLK),SWRCH18A SNA
BN96-00054C STD ASSY󰼿STAND󰼿P APOLLO29,ABS󰼿VO󰼿GR81,DG-703P
BN90-00446A 󰼿- ASSY󰼿COVER󰼿FRONT AL29UO,U.S.A SNA
6003-000009 P/BRKT+C/F SCREW-TAPTITE BH,+,B,M4,L16,ZPC(YEL),SWRCH18 SNA
BN64-00101C C/F BADGE-BRAND AL29NO,AL,T1.5,11.5,65,DG-703P,SAMSUNG SNA
BN96-00056D C/F ASSY󰼿COVER󰼿P-FRONT AL29UO,ABS󰼿VO,FOR󰼿USA
6003-001188 C/F SCREW-TAPTITE BH,+,B,M4,L10,YEL,SWRCH18A SNA
BN59-00290A C/F BOARD-FUNCTION󰼿ASS'Y AL29NO,CT5000-0600,FUNCTION󰼿ASS'Y
BN63-00230A C/F COVER-FRONT APOLLO29,ABS,V0,SILVER,SPRAY SNA
BN64-00061A C/F KNOB-RING APOLLO29,ABS󰼿,HB,CLEAR
BN64-00062A C/F KNOB-FUNCTION APOLLO29,ABS+PC,5V,SILVER
BN64-00101A C/F BADGE-BRAND APOLLO,AL,T1.5,11.5,65,SVM-2012,SAMSUNG SNA
BN67-00055A C/F LENS-LED APOLLO29,ACRYL,CLEAR SNA
BN67-00056A C/F LENS-MIRROR APOLLO29,ACRYL,CLEAR,AL󰼿COATING
BN67-00070A C/F LENS-IR APOLLO29,ACRYL,CLEAR
BN90-00448A 󰼿- ASSY󰼿COVER󰼿REAR AL29UO,U.S.A SNA
6003-001003 C/F+C/R SCREW-TAPTITE BH,+,B,M4,L12,ZPC(BLK),SWRCH18
BN63-00232D C/R COVER-REAR AL29UO,ABS+PC,USA SNA
BN91-00388A 󰼿- ASSY󰼿LCD AL29NO SNA
BN07-00063A CIS LCD TM290WX-71N31,RS24NS,6BIT󰼿FRC,684.0*426.5*45.0,16.7M,40,0.4935*0.4935,0󰾝40,5.0,T
BN91-00518A 󰼿- ASSY󰼿MISC AL29/40UO,U.S.A SNA
BN44-00067C CIS ADAPTOR PSCV22101B,󰼿AMERICA,APPOLLO,100-240V,47-63HZ,28VDC,8ADC,224W,AMERICA,󰼿UL󰼿AREA
BN91-00552A 󰼿- ASSY󰼿CHASSIS AL29UO,U.S.A
BN94-00403A 󰼿- ASSY󰼿PCB󰼿MAIN AL29UO,U.S.A SNA
0202-001044 CIS01 SOLDER-WIRE. S63S-W3.0,S63S,D3,63Sn/37Pb,- SNA
0202-001172 CIS03 SOLDER-WIRE󰼿FLUX RS-107,RS60,D1.2,SN60/PB40,- SNA
0204-001096 CIS04 ETHANOL ISO-PROPYLENE,C2H50H,99.8%,- SNA
0204-001527 CIS05 FLUX DF-201TVS,MIX,0.820,FLUX󰼿13%,󰼿14KG SNA
1001-001037 IC1 IC-RF/VI/AUDIO󰼿S/W TA8851CN,-,DIP,54P,600MIL,SING
2801-003224 X102 CRYSTAL-UNIT 32.768KHz,20ppm,28-AAY,12.5pF,
3711-003846 CN950 CONNECTOR-HEADER BOX,8P,1R,2mm,ANGLE,SN SNA
3711-004123 CN501 CONNECTOR-HEADER BOX,15P,1R,2mm,ANGLE,SN SNA
3711-004261 CN2 CONNECTOR-HEADER BOX,12P,1R,2MM,ANGLE,SN SNA
6001-000677 CIS06 SCREW-MACHINE RH,+,M3,L6,ZPC(YEL),SM20C,- SNA
BN27-00012A L901 COIL󰼿CHOKE 5UH,APPOLO,5UH,10%,0.01OHM󰼿MAX,10A,PEI3210S,1T,40X70X25MM,BK,-10CTO+85C
BN73-00025A CIS07 RUBBER󰼿CUSHION AL29NO,CR,10*15,60,T4,BLACK,3M󰼿#9448 SNA
BN96-00093A CIS08 ASSY󰼿MISC󰼿P-SHIELD/D-SUB AL29NO,SPTE󰼿T0.5 SNA
BN97-00164P CIS09 ASSY󰼿MICOM AL29UO,U.S.A
1102-001108 IC105 IC-EPROM 27C020,256Kx8Bit,PLCC,32P,495MIL,70nS,5V,10%,PLASTIC,0to+70C,100uA,CMOS,TR
BN82-00075U CIS A/S󰼿MICOM AL29UO,U.S.A SNA
BN97-00174A 󰼿- ASSY󰼿SMD PD22EO,EUROPE SNA

Page󰼿1

0202-001162 CIS02 SOLDER-CREAM RMA-20-21L,S63,-,SN63/PB36.6/AG0.4,FLUX9.5% SNA
0401-001056 D1 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D2 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D3 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D401 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D402 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D403 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D404 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D405 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D406 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D501 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D502 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D503 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D504 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D505 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D506 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D507 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D508 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D6 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D7 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D8 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001056 D9 DIODE-SWITCHING MMBD4148SE,75V,200MA,SOT-23,TP
0401-001116 D201 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D202 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D203 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D204 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D205 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D206 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D207 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0401-001116 D208 DIODE-SWITCHING BAV99DW,75V,150MA,SOT-363,TP
0402-000553 ZD901 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD950 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD951 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD952 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD953 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD954 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0402-000553 ZD955 DIODE-RECTIFIER SS24,40V,2.0A,DO-214AA
0403-000579 ZD1 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD2 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD201 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD202 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD203 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD204 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD205 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD206 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD207 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD208 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23

Page󰼿2

0403-000579 ZD209 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD210 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD501 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-000579 ZD505 DIODE-ZENER BZX84C5V1,5.1V,5%,200mW,SOT-23
0403-001052 ZD502 DIODE-ZENER RD8.2MB,8.2V,7.7-8.64V,200mW,S
0403-001052 ZD503 DIODE-ZENER RD8.2MB,8.2V,7.7-8.64V,200mW,S
0403-001052 ZD504 DIODE-ZENER RD8.2MB,8.2V,7.7-8.64V,200mW,S
0403-001052 ZD506 DIODE-ZENER RD8.2MB,8.2V,7.7-8.64V,200mW,S
0403-001052 ZD507 DIODE-ZENER RD8.2MB,8.2V,7.7-8.64V,200mW,S
0404-001055 D902 DIODE-SCHOTTKY -,60V,3000MA,SMC,TP
0404-001055 D903 DIODE-SCHOTTKY -,60V,3000MA,SMC,TP
0404-001084 D901 DIODE-SCHOTTKY BAT54A,30V,200MA,SOT-23,TP
0501-000280 Q1 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q10 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q11 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q13 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q16 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q4 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q5 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q7 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-000280 Q8 TR-SMALL󰼿SIGNAL KSA1182,PNP,150mW,SOT-23,TP,70
0501-002080 Q101 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q12 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q14 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q15 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q2 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q3 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q301 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q501 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q6 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q901 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q906 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q950 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q951 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q952 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q953 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q954 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q955 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0501-002080 Q956 TR-SMALL󰼿SIGNAL 2SC2412K,NPN,200mW,SC-59,TP,120-270
0505-000275 IC905 FET-SILICON SI4435DY,P,-30V,+-8.0A,0.014ohm,2.5W,SO-8
0505-001170 IC963 FET-SILICON SI9933ADY-T1,P,-20V,3.4A,0.06ohm,2W,SO-8
0505-001662 Q904 FET-SILICON FDB5645,N,60V,80A,0.0095OHM,125W,TO-263AB
0505-001662 Q905 FET-SILICON FDB5645,N,60V,80A,0.0095OHM,125W,TO-263AB
0505-001663 Q902 FET-SILICON FQB50N06L,N,60V,52.4,0.021OHM,3.75W,D-PAK
0505-001663 Q903 FET-SILICON FQB50N06L,N,60V,52.4,0.021OHM,3.75W,D-PAK
0801-002267 IC205 IC-CMOS󰼿LOGIC 74LCX14,-,SOIC,14P,150MIL,-,TP,-,-,-,3.6V,-40TO+85C,-,5.5V,-,-,24MA
0801-002267 IC604 IC-CMOS󰼿LOGIC 74LCX14,-,SOIC,14P,150MIL,-,TP,-,-,-,3.6V,-40TO+85C,-,5.5V,-,-,24MA

Page󰼿3

0801-002268 IC110 IC-CMOS󰼿LOGIC 74VHC139,DECODER,SOP,16P,150MI
0801-002394 IC107 IC-CMOS󰼿LOGIC 74LCX32,OR󰼿GATE,SOIC,14P,150MI
0801-002394 IC112 IC-CMOS󰼿LOGIC 74LCX32,OR󰼿GATE,SOIC,14P,150MI
0801-002559 IC104 IC-CMOS󰼿LOGIC 74LVX74,D󰼿FLIP-FLOP,TSSOP,14P,173MIL,DUAL,TP,PLASTIC,-,-,0.36V,-40to+85C,180mW,2
0801-002559 IC405 IC-CMOS󰼿LOGIC 74LVX74,D󰼿FLIP-FLOP,TSSOP,14P,173MIL,DUAL,TP,PLASTIC,-,-,0.36V,-40to+85C,180mW,2
0801-002574 IC106 IC-CMOS󰼿LOGIC 74LVX04,INVERTER,SOP,14P,150MIL,HEX,TP,PLASTIC,-,-,0.36V,-40to+85C,180mW,2.4V,20
0801-002576 IC109 IC-CMOS󰼿LOGIC 74LVX373,LATCH,SOP,20P,300MIL,OCTAL,TP,PLASTIC,3-STATE,-,0.36V,-40to+85C,180mW,2
0903-001202 IC103 IC-MICROCONTROLLER 80251G2,8Bit,PLCC,44P,653MIL,24MHz,TR,CMOS,PLASTIC,5V,1.5W,0to+70C,1KBYTE,-,24Bi SNA
0909-001037 IC111 IC-REAL󰼿TIME󰼿CLOCK M41ST84YMQ6TR,64BIT,SO16,16P,21.21X14.22MM,400KHZ,TP,CMOS,PLASTIC,-,1W,-40TO+85C
1001-001082 IC306 IC-VIDEO󰼿SWITCH BA7657F,-,SOP,24P,300MIL,SINGL
1001-001082 IC403 IC-VIDEO󰼿SWITCH BA7657F,-,SOP,24P,300MIL,SINGL
1001-001146 IC304 IC-ANALOG󰼿SWITCH FST3257,BUS󰼿SWITCH󰼿&󰼿CMOS,SOP,16P,150MIL,QUAD,5.5V,-40to+85C,PLASTIC,-,15ohm,-,­1001-001146 IC406 IC-ANALOG󰼿SWITCH FST3257,BUS󰼿SWITCH󰼿&󰼿CMOS,SOP,16P,150MIL,QUAD,5.5V,-40to+85C,PLASTIC,-,15ohm,-,­1001-001146 IC701 IC-ANALOG󰼿SWITCH FST3257,BUS󰼿SWITCH󰼿&󰼿CMOS,SOP,16P,150MIL,QUAD,5.5V,-40to+85C,PLASTIC,-,15ohm,-,­1001-001190 IC702 IC-ANALOG󰼿SWITCH FST16233MTD,BUS󰼿SWITCH,TSSOP,56P,240MIL,-,5.5V,-40TO+85C,PLASTIC,-,20OHM,8.5NS,7
1002-001292 IC203 IC-A/D󰼿CONVERTER AD9883AKST-110,8BITS,QFP,80P,551MIL,±0.5LSB,TR,CMOS,PLASTIC,3.3V,-25TO+85C,650M
1002-001292 IC404 IC-A/D󰼿CONVERTER AD9883AKST-110,8BITS,QFP,80P,551MIL,±0.5LSB,TR,CMOS,PLASTIC,3.3V,-25TO+85C,650M
1103-000129 IC207 IC-EEPROM 24C02,256x8BIT,SOP,8P,150MIL,1
1103-001223 IC102 IC-EEPROM 24C16,2048x8Bit,SOP,8P,150MIL,10mS,2.7V,-,PLASTIC,0to+70C,4uA,CMOS,TP
1105-001336 IC601 IC-DRAM 4S643232,512Kx32x4Bit,TSOP,86P,400MIL,60nS󰼿,3.3V,10%,PLASTIC,0to+70C,2mA,CMOS,TP
1105-001336 IC602 IC-DRAM 4S643232,512Kx32x4Bit,TSOP,86P,400MIL,60nS󰼿,3.3V,10%,PLASTIC,0to+70C,2mA,CMOS,TP
1105-001336 IC704 IC-DRAM 4S643232,512Kx32x4Bit,TSOP,86P,400MIL,60nS󰼿,3.3V,10%,PLASTIC,0to+70C,2mA,CMOS,TP
1105-001336 IC802 IC-DRAM 4S643232,512Kx32x4Bit,TSOP,86P,400MIL,60nS󰼿,3.3V,10%,PLASTIC,0to+70C,2mA,CMOS,TP
1105-001336 IC803 IC-DRAM 4S643232,512Kx32x4Bit,TSOP,86P,400MIL,60nS󰼿,3.3V,10%,PLASTIC,0to+70C,2mA,CMOS,TP
1201-001495 IC505 IC-AUDIO󰼿AMP 7050,SOP,8P,150MIL,DUAL,26DB,PLASTIC,6V,0.25W,-,40DB,-,-,20NA,­1201-001681 IC504 IC-AUDIO󰼿AMP 1101,SOP,30P,433MIL,-,-,PLASTIC,13.2V,-,0to+70C,-,-,-,-,-,TP
1203-001432 IC904 IC-POSI.FIXED󰼿REG. 78M12,DPAK,3P,-,PLASTIC,11.5/1
1203-001448 IC901 IC-SWITCH󰼿VOL.󰼿REG. 2596,TO-263,5P,-,PLASTIC,4.750
1203-001448 IC951 IC-SWITCH󰼿VOL.󰼿REG. 2596,TO-263,5P,-,PLASTIC,4.750
1203-001448 IC952 IC-SWITCH󰼿VOL.󰼿REG. 2596,TO-263,5P,-,PLASTIC,4.750
1203-001448 IC955 IC-SWITCH󰼿VOL.󰼿REG. 2596,TO-263,5P,-,PLASTIC,4.750
1203-001448 IC958 IC-SWITCH󰼿VOL.󰼿REG. 2596,TO-263,5P,-,PLASTIC,4.750
1203-001465 IC950 IC-POSI.ADJUST󰼿REG. 317,TO-263,3P,-,PLASTIC,1.2/37
1203-001465 IC961 IC-POSI.ADJUST󰼿REG. 317,TO-263,3P,-,PLASTIC,1.2/37
1203-001465 IC964 IC-POSI.ADJUST󰼿REG. 317,TO-263,3P,-,PLASTIC,1.2/37
1203-001488 IC502 IC-POSI.FIXED󰼿REG. 7805,T0-252,3P,-,PLASTIC,4.8/5
1203-001559 IC101 IC-RESET DS1834,SOIC,8P,150MIL,-,1.2/5V
1203-001815 IC959 IC-POSI.FIXED󰼿REG. 78M09,TO-252,3P,-,PLASTIC,8.6/9.4V,1.0W,-40TO+85C,0.5A,-,TP
1203-001815 IC960 IC-POSI.FIXED󰼿REG. 78M09,TO-252,3P,-,PLASTIC,8.6/9.4V,1.0W,-40TO+85C,0.5A,-,TP
1203-001816 IC501 IC-POSI.FIXED󰼿REG. 78M08,TO-252,3P,-,PLASTIC,7.7/8.3V,1.0W,-40TO+85C,0.5A,-,TP
1203-002067 IC201 IC-POSI.FIXED󰼿REG. 3330,SOT-23,6P,65MIL,PLASTIC,3.284/3.316V,-,-40to+125C,200mA,-,TP
1203-002067 IC202 IC-POSI.FIXED󰼿REG. 3330,SOT-23,6P,65MIL,PLASTIC,3.284/3.316V,-,-40to+125C,200mA,-,TP
1203-002067 IC206 IC-POSI.FIXED󰼿REG. 3330,SOT-23,6P,65MIL,PLASTIC,3.284/3.316V,-,-40to+125C,200mA,-,TP
1203-002067 IC401 IC-POSI.FIXED󰼿REG. 3330,SOT-23,6P,65MIL,PLASTIC,3.284/3.316V,-,-40to+125C,200mA,-,TP
1203-002067 IC402 IC-POSI.FIXED󰼿REG. 3330,SOT-23,6P,65MIL,PLASTIC,3.284/3.316V,-,-40to+125C,200mA,-,TP
1203-002191 IC906 IC-DC/DC󰼿CONVERTER LTC1778,SSOP,16P,153MIL,PLASTIC,-,-,125C,-,-,TP
1203-002199 IC962 IC-POSI.FIXED󰼿REG. LM2596,TO-263,5P,340MIL,PALSTIC,-,-,-40TO+125C,-,-,ST

Page󰼿4