Samsung PS-42P2S User Manual
PLASMA DISPLAY
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ENG
REMOTE CONTROL
ON-SCREEN MENUS
PICTURE IN PICTURE
2
ENG
Safety Instructions
◆ Do not place the PDP on an unstable cart, stand, tripod, bracket, table, or floor where it can fall.
◆ Do not expose the PDP to extreme temperature conditions or to extreme humidity conditions.
◆ Do not expose the PDP to direct sunlight and other sources of heat.
◆ Do not expose the PDP to any liquids.
◆ Never put objects of any kind into the television, and do not place a water-containing vessel on the
PDP.
◆ During a storm conditions (especially when there is lightning) unplug the PDP from the mains
socket and aerial.
◆ Do not step on or twist the power cord.
◆ Do not overload wall outlets or extension cords as this can result in a risk of fire or electric shock.
◆ Please use a soft and dry cloth (not containing volatile matter) when you clean the PDP.
◆ If the PDP is broken, do not try to repair it yourself. Contact qualified service personnel.
◆ If the remote control is not used for a long period of time, remove the batteries and store it in a
cool, dry place.
◆ Do not drop the remote control.
User Instructions
◆ Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the
plasma monitor panel for more than 2 hours as it can cause screen image retention. This image
retention is also known as “screen burn”. To avoid such image retention, reduce the degree of
brightness and contrast of this screen when displaying a still image.
◆ Cell Defect
The plasma display panel consistes of fine cells. Although the panels are produced with more than
99.9 percent active cells, there may be some cells that do not produce light or remain lit.
◆ Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place
over 2000m in height and do not install and operate there.
◆ Warranty
- Warranty does not cover any damage caused by image retention.
- Burn-in is not covered by the warranty.
3
ENG
Caution
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
The lightning flash and arrow head
within the triangle is a warning sign
alerting you of “dangerous voltage”
inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
☛
The main voltage is indicated on the
rear of the PDP and the frequency is
50 or 60Hz.
WARNING: TO PREVENT DAMAGE WHICH MAY
RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Checking Parts
Owner’s Instructions
Remote Control/
AAA Batteries
Ferrite Cores
Power Cord AV Cables (RCA) S-VIDEO Cable
4
ENG
Contents (continued)
◆ FOREWORD
■ Safety Instructions .................................................................................................... 2
■ User Instructions....................................................................................................... 2
■ Caution ..................................................................................................................... 3
■ Checking Parts ......................................................................................................... 3
◆ CONNECTING AND PREPARING YOUR DISPLAY
■ Your New Plasma Display Panel .............................................................................. 6
■ Remote Control Buttons ........................................................................................... 8
■ Inserting the Batteries in the Remote Control........................................................... 9
■ Installing the Display on the Wall Attachment Panel ................................................ 9
■ Separating the Display from the Wall Attachment Panel .......................................... 12
■ Before Connecting the Display to External Equipment............................................. 12
■ Connecting Speakers ............................................................................................... 13
■ Connecting a VCR or Cable Box .............................................................................. 14
■ Connecting a DVD Player or Set-top Box................................................................. 15
■ Switching On and Off................................................................................................ 16
■ Viewing the Menus and Displays.............................................................................. 16
◆ USING YOUR DISPLAY
■ Using the Various Setup Menus ............................................................................... 17
-
Color System / Digital NR / Auto Power ON / Panel Lock / Language
■ Using Automatic Picture Settings ............................................................................. 18
■ Customizing the Picture............................................................................................ 18
■ Changing the Picture Format.................................................................................... 19
■ Freezing the Current Picture..................................................................................... 19
■ Adjusting the Volume................................................................................................ 20
■ Using Automatic Sound Settings .............................................................................. 21
■ Customizing the Sound............................................................................................. 21
■ Setting the Current Time........................................................................................... 22
■ Switching On and Off Automatically ......................................................................... 22
■ Setting the Sleep Timer ............................................................................................ 23
■ Viewing the Picture in Picture (PIP).......................................................................... 24
■ Displaying Informations ............................................................................................ 25
■ Viewing Pictures From External Sources ................................................................. 26
5
ENG
Contents
◆ CONNECTING AND OPERATING A PC
■ Connecting a PC....................................................................................................... 27
■ Setting up Your Display Plug and Play ..................................................................... 28
■ Preset Signals........................................................................................................... 28
■ Setting up Your PC Software.................................................................................... 29
■ PC Input Mode.......................................................................................................... 30
■ Controlling the Screen Color..................................................................................... 31
■ Adjusting the Screen Quality .................................................................................... 31
■ Changing the Screen Position .................................................................................. 32
■ Initializing the Frequency, Phase, and Position ........................................................ 32
■ Changing the Screen Size ........................................................................................ 33
■ Enjoying the PIP Feature in PC mode ...................................................................... 33
◆ RECOMMENDATIONS FOR USE
■ Care and Maintenance ............................................................................................. 34
■ Troubleshooting: Before Contacting Service Personnel ........................................... 34
■ Wiring the Mains Power Supply Plug (UK Only)....................................................... 35
6
ENG
Your New Plasma Display Panel
POWER
Press to turn the
PDP on and off.
SPEAKER SPEAKER
Remote Control Signal Receiver
Aim the remote control towards this spot on
the PDP.
SOURCE
External input selection.
MENU
Menu display.
-
VOLUME +
Volume adjustment.
▼ SELECT ▲
Control the cursor in the Menu.
MUTE
Temporary sound switch-off.
Front Panel
7
ENG
Your New Plasma Display Panel
Rear Panel
a) External Speaker Outputs (8Ω)
Connect external speakers.
b) S-VIDEO Input
Connect a S-Video signal from an S-VHS VCRs
or DVD players.
c) VIDEO Input
Connect a video signal from external sources
like VCRs or DVD players.
d) PC Input
Connect a PC signal from an PC.
e) Component1 (480i/576i)
Connect a video signal from DVD players
(480i/576i).
f) Component2 (480p/576p/720p/1080i)
Connect a video signal from external sources
like Set-top box or DVD players (480p/576p/
720p/1080i).
g) Audio Inputs
Connect a audio signal from external sources
like VCRs, DVD players, Set-top box or PC.
8
ENG
Remote Control Buttons
AUTOMATIC SWITCH-OFF
VCR/DVD FUNCTIONS;
(STOP/REWIND/PLAY/PAUSE/
FAST-FORWARD)
POWER ON/OFF
NUMERIC BUTTONS
TEMPORARY SOUND SWITCH OFF
VOLUME DECREASE
DISPLAYING INFORMATIONS
SOUND EFFECT SELECTION
PICTURE EFFECT SELECTION
STILL THE MAIN PICTURE
PICTURE SIZE SELECTION
VOLUME INCREASE
CONTROL THE CURSOR IN THE MENU
MENU DISPLAY
MAKE THE REMOTE CONTROL WORKS
FOR MONITOR, VCR, CABLE,
DVD PLAYER
EXTERNAL INPUT SELECTION
➢ It is possible that the work of the transmitter is dull or not operated normally
if the light of the Bulb is on around the PDP.
PIP FUNCTIONS;
PIP ON/SWAP/LOCATE/
SIZE SETTING/STILL/SCAN/
CHANNEL SELECTION(P
▼/▲)/
MULTI DISPLAY/
INPUT SOURCE SELECTION (SOURCE)
CHANGE CONFIRMATION
SELECT TO THE PC MODE DIRECTLY
➢
Some remote control buttons do not operate with the PDP.
Power
9
ENG
continued...
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the PDP
◆ Find that the remote control is no longer operating
correctly
1 Remove the cover on the rear of the remote control by pressing
the symbol downwards and then pulling firmly to remove it.
2 Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking
care to respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3 Replace the cover by aligning it with the base of the remote
control and pressing it back into place.
➢
Do not mix battery types, i.e. alkaline and manganese.
Inserting the Batteries in the Remote Control
Installing the Display on the Wall Attachment Panel
◆
Do not install the PDP on any place other than vertical walls.
◆
To protect the performance of the PDP and prevent troubles, avoid the
followings:
-
Do not install next to smoke and fire detectors.
-
Do not install in an area subjected to vibration or high voltage.
-
Do not install in the wall.
-
Do not install near or around any heating apparatus.
◆
Use only recommended parts and components.
Installation Notes
➢
Wall attachment panel is sold separately. Check with your dealer.
10
ENG
Installing the Display on the Wall Attachment Panel
➢
Wall attachment panel is sold separately. Check with your dealer
1 Check for the stability of the wall where the PDP is to be installed. If the wall is not enough strong to
support the PDP, strengthen the wall before installation.
2 Fix the wall attachment panel on the
wall using bolts as shown in the figure:
Fixing bolts must protrude from the
wall appox. 1.5 cm.
3 Using the wall attachment panel, you may adjust the angle of the display from 0 to 20 degrees. The
angle can be set in 5 stages with 5 degrees of distance each using the angle control holes on the sides
of the panel.
When the angle has
been set to 5 degrees.
When the angle has
been set to 15 degrees.
When the panel hasn't
been tilted.
5 degrees of tilt
10 degrees of tilt
15 degrees of tilt
No tilt
20 degrees of tilt
Angle control holes
11
Installing the Display on the Wall Attachment Panel
ENG
4 Remove four large screws from the rear side of the display.
Insert the bolts, dish-type washers, and insulation rubber
into the four screw-holes as shown in the figure:
5 Put the insulation rubber point
protruding from the rear top of the
display in the groove on the top of the
wall attachment panel. Lift up the
display a little bit so that the
insulation rubber point at the bottom
of the rear side of the display is put to
the groove at the bottom of the wall
attachment panel. (Do not lift the
display with any pressure. The
insulation rubber at the top may be
taken off.)
Bolt
Insulation rubber
´
Œ
Loading...