OPERATING GUIDE V2
QUICK-START OPERATION |
1 |
FBX-1020PLUS OPERATING INSTRUCTIONS |
6 |
|
DECLARATION OF CONFORMITY |
2 |
WHERE THE FBX FITS IN YOUR SOUND SYSTEM |
6 |
|
ABOUT THE FBX-1020PLUS |
3 |
A NOTE ABOUT GRAPHIC EQUALIZERS |
6 |
|
UNDERSTANDING FIXED & DYNAMIC FILTERS |
6 |
|||
FREQUENCY RESPONSE |
3 |
|||
CLIPGUARD™ ADAPTIVE CLIP LEVEL CONTROL |
6 |
|||
WORLD'S BEST FEEDBACK CONTROLLER |
3 |
|||
CLIPGUARDTM TURBO MODE GUIDE |
6 |
|||
WHO NEEDS FBX? |
3 |
|||
FBX SETUP FOR SINGLE INSERT POINT |
7 |
|||
WHY THE FBX? |
3 |
|||
FBX SETUP FOR INSERT SEND & RETURN |
7 |
|||
DIRECT HIT ON FEEDBACK! |
3 |
|||
HOW TO OPERATE THE FBX-1020PLUS |
7 |
|||
ACTIVE/BYPASS SWITCH |
4 |
|||
HOW TO USE THE FBX-1020PLUS FEATURES |
8 |
|||
SIGNAL LEVEL |
4 |
|||
USING THE LOCK FIXED FEATURE |
8 |
|||
DUAL-FUNCTION RESET |
4 |
|||
SELECTING FILTER WIDTH |
8 |
|||
SET TOTAL NUMBER OF FILTERS |
4 |
|||
IMPORTANT OPERATING CONSIDERATIONS |
8 |
|||
SET FIXED |
4 |
|||
MEMORY |
8 |
|||
A/C POWER INPUT |
4 |
|||
BYPASS MODE |
8 |
|||
AUDIO INPUTS & OUTPUTS |
4 |
|||
RESETTING THE FILTERS |
8 |
|||
FBX-1020PLUS CONTROLS |
4 |
|||
TURBO MODE SETUP |
8 |
|||
LOCK FIXED FILTERS |
4 |
|||
DEFEATING TURBO MODE |
8 |
|||
FIFTH OCTAVE |
4 |
|||
MOBILE VS. STATIONARY MICROPHONES |
8 |
|||
FILTER STAGE ACTIVITY |
4 |
|||
FREQUENTLYASKED QUESTIONS |
9 |
|||
POWER SWITCH |
4 |
|||
INDEX |
9 |
|||
FUSE |
4 |
|||
|
|
|||
APPLICATION DIAGRAMS |
5 |
FBX-1020PLUS ENGINEERING SPECIFICATIONS |
10 |
|
FBX SETUP FOR MONITORS |
5 |
CAUTIONS & WARNINGS |
11 |
|
FBX SETUP FOR ENTIRE MIX |
5 |
LIMITED WARRANTY |
12 |
|
|
|
|
|
QUICK-START OPERATION
For best results, read all operating instructions before using the FBX-1020Plus. If you're already familiar with the FBX or just want a basic overview of FBX operation, this simple quick-start procedure is for you. More detailed instructions are on page 7 inside this operating guide.
1.Place the FBX between the output of your mixer and the input of your power amp.
2.With the master volume down, put the FBX-1020Plus in active mode (red BYPASS LED off), then slowly raise the mixer master volume to the point of feedback.
3.Keep raising the master volume until all of your fixed filters and one dynamic filter are set, then lower the volume slightly. (Factory default is nine fixed and three dynamic filters.) The rest of the filters continually catch and update new feedback frequencies throughout the program. You're ready to go.
READ THE ENTIRE OPERATING GUIDE FOR COMPLETE INSTRUCTIONS.
CONGRATULATIONS! You now have the state-of-the-art in feedback control. Your Sabine FBX-1020Plus Feedback Exterminator® — a single channel, 20-bit digital filtering device — gives you automatic real-time feedback control and increases the clarity and volume of your system.
The FBX-1020Plus incorporates the latest in digital signal processing technology. It automatically senses feedback in a sound system and determines its pitch. It then places one of 12 Constant Q micro-filters on the resonating frequency and eliminates the feedback in typically less than one second.
|
Special features of the FBX-1020Plus: |
||
|
• |
An improved algorithm that allows the FBX-1020Plus to better distinguish the difference between feedback and music |
|
|
• |
Improved 20-bit digital resolution, providing superior dynamic range and signal-to-noise ratio |
|
Inc. |
• |
12 feedback filters, giving the unit more feedback elimination power for the toughest venues. |
|
• |
ClipGuard™ adaptive clip level control, with TURBO setup mode, increases the effective dynamic range by more than 10dB |
||
Sabine, |
|||
|
and makes setup faster and easier. |
||
|
|
||
2001 |
• |
Two stage reset function allows you to reset just dynamic filters or all filters. |
|
• |
StandardFBXfeaturessuchas lockablefixedfiltersand switchable1/10-and1/5-octaveConstantQfiltersarealsoincluded |
||
© |
|||
|
and now have convenient front panel switches. |
||
|
|
||
DECLARATION OF CONFORMITY
Application of Council Directive: 73/23/EEC and 89/336/EEC
Standard to which conformity is declared:
EN 60065:1993
EN 50082-1:1992
EN 55022 Class B
Manufacturer’s Name: |
Sabine, Inc. |
Manufacturer’s Address: |
13301 Highway 441 |
|
Alachua, FL 32615-8544 USA |
Type of Equipment: |
Equalizer |
Model No.: |
FBX-1020Plus |
Serial No.: |
|
Year of Manufacture: |
1997 and on |
I, the undersigned, herby declare that the equipment specified above conforms to the above Directive and Standard.
Place: |
Alachua, Florida, USA |
Signature: |
|
Date: |
October 4, 2000 |
Full Name: Doran Oster, Sabine President |
|
|
|
|
|
2
ABOUT THE FBX-1020Plus
Feedback |
FBX filter |
Frequency |
|
Direct Hit on Feedback!
The FBX targets feedback without taking a big chunk out of your sound. Tests prove that a single 1/3-octave EQ slider pulled down 12 dB removes almost half the power going to the speakers over a two-octave range. And, as this illustration shows, you can't place a graphic EQ filter precisely on the ringing frequency. When you pull down multiple sliders in a normal setup (below), you end up with giant holes in your music. On the other hand, FBX micro-filters are 10 times narrower - you get back up to 90% of the power you lose with a graphic EQ! That means more gain before feedback and no loss in sound quality.
FREQUENCY RESPONSE: FBX 1/10-Octave Filter Vs.
1/3-Octave Graphic EQ Filter (12 dB depth; Log Scale).
Frequency Response
Full Set-Up FBX Vs. 1/3 Octave Graphic Equalizer. Test procedure: A PA system was set up using a microphone, mixer, FBX, power amp and two speakers. The system's gain was raised until the FBX removed nine feedback points. Next, the FBX was replaced with a 1/3 octave graphic EQ. The EQ was adjusted while the system gain was raised to the same level achieved with the FBX. The frequency response curves of each device were then plotted.
World's Best Feedback Controller
Before the invention of the FBX, the most common device for controlling feedback was the 31-band graphic EQ. However, the FBX has three distinct advantages. The most obvious is the FBX functions automatically, even during the program. Another is the FBX micro-filters are precisely placed while EQ filters are fixed. The difference: FBX filters do not have to be as deep, so there is more system gain. The most important advantage is that FBX micro-filters are ten times narrower than 31-band EQ filters. FBX micro-filters return up to 90 percent of the power removed by EQ filters.
Over the years, engineers stopped using 12-band EQs in favor of the narrower-filter 31-band EQ for controlling feedback. The FBX represents the next step. An EQ would need more than 10,000 sliders to be equivalent to your FBX. With the FBX-1020Plus, your monitors will finally sound loud enough, everyone in the audience will understand each word, and the mains will sound natural and transparent.
Who Needs FBX?
Virtually every sound system will be improved with the FBX. Small bands that do not have sound technicians can now increase their monitor volumes so they can hear themselves clearly and with full fidelity, without worrying if the program is going to be ruined by feedback.
Auditoriums and churches of all sizes will enjoy reliable feedback control. Hotels and conference centers around the world can offer meeting rooms with sound systems that won’t howl during programs. The FBX-1020Plus can be installed in theaters, schools, sports arenas, courtrooms — anywhere multiple microphones are used. It can also be used for teleconferencing, intercoms or interactive remote classrooms.
Why the FBX?
The simple beauty of the FBX is its ability to quickly and effectively eliminate feedback with narrower filters than ever before possible. The FBX delivers superior sound quality automatically.
3
3
FBX-1020PLUS CONTROLS
FBX-1020Plus Front Panel
Active/Bypass Switch
Bypass mode takes the unit out of the signal path so that it will have no effect on the program. In active mode, the unit controls feedback automatically. The red BYPASS LED lights when the unit is in bypass mode.
Signal Level
The LED ladder indicates the signal strength relative to the FBX's input clip level. The red CLIP LED indicates clipping; it also indicates the unit is in TURBO mode.
Dual-Function Reset
To reset only the dynamic filters, press and hold the reset button. All LEDs will flash 3 times and then the LEDs that indicate current dynamic filter placement will shut off (fixed filter LEDs will remain on). To reset ALL filters, continue holding the reset button for 4 more flashes (for a total of 7 flashes), until all filter LEDs are off.
Set Total Number of Filters
To set the total number of filters, depress the button for 4 seconds and then release. The LEDs will begin to light in sequence. When the LED corresponding to the desired number of filters lights, press the button to register your selection.
Lock Fixed Filters
When the LOCK FIXED button is pressed, its LED will light to indicate that the FBX is in LOCK FIXED mode. LOCK FIXED mode can be activated at any time after system setup and will stay on until the button is pressed again and the LED turns off. Engaging the LOCK FIXED button also takes the FBX-1020Plus out of ClipGuard's TURBO setup mode.
Fifth Octave
Press the button at any time to select wider filters for any new filters to be set. It is possible to have both 1/5 and 1/10 octave Constant Q filters active in one channel simultaneously.
Filter Stage Activity
When one of the unit’s 12 filters is activated, the corresponding LED lights. A blinking LED indicates the filter that was most recently activated.
Power Switch
The ON/OFF switch is a two-position push button switch. The power indicator LED will light when the FBX is operational.
Set Fixed
To set fixed filters, hold down the button for 4 seconds and then release. The LEDs will begin to light in sequence. When the LED corresponding to the desired number of fixed filters lights, press the button to register your selection. (Factory default is nine fixed and three dynamic filters.)
FBX-1020Plus Back Panel
A/C Power Input
The FBX-1020Plus is factory configured to operate at either 115 VAC or 230 VAC. Using the wrong input voltage may cause permanent damage to the unit and will void the warranty.
Audio Inputs & Outputs
1/4" TRS and XLR balanced and unbalanced.
Fuse
This equipment is fitted with an IEC power inlet incorporating a built-in fuse holder. To change the fuse in this socket:
1.Disconnect the power cord from the unit.
2.Pull out the fuse holder and remove the old fuse.
3.Install the new fuse into the holder. Replace only with 5x20mm, 0.315A, 250V F (fast acting) fuse.
4.Refit the fuse cover.
4
Loading...