Ricoh Sp 213Nw, sp 213FNw Setup Manual
SP 213Nw/SP 213SNw/SP 213SFNw
Setup Guide
Read this manual carefully before you use this machine and keep it handy for future reference.
For safe and correct use, be sure to read Safety Information before using the machine. This
manual briefly describes the procedure for installing this machine. For more details about other
information, see User Guide in the CD-ROM
.
Manuals in English are on the supplied CD-ROM
follows:
DAC345
DCT073
. To read a manual on the CD-ROM , do as
CXP074
DCT092
1
1. Setting Up the Machine
Place to Install
SP 213SNw/SP 213SFNw
10 cm
(4.0”)
45 cm
(17.8”)
SP 213Nw
10 cm
(4.0”)
45 cm
(17.8”)
40 cm
(15.8”)
20 cm
(7.9”)
20 cm
(7.9”)
DCT074
40 cm
(15.8”)
20 cm
(7.9”)
10 cm
(4.0”)
CTT017
Unpacking
DCT048
DCT027
Power Source
110 V, 60 Hz, 8A•
DCT071
2
DCT024
DCT028
DCT094
CTT049
DCT026
3
Loading Paper
tray 1
CTT074
DCT063
DCT032
CTT148
DCT049
CTT300
CTT029
CTT073
4
Bypass tray
DCT029
DCT013
Using the Fax Function
SP 213SFNw Only
Connection
1
2
CTT214
1. Port For External Telephone
2. Port For LINE
DCT093
Selecting the Telephone Line
Type
Press the [ ] key.
DCT014
DHA103
Press the [ ] or [ ] key s to selec t [Ad -
min. Tools], and then press the [ ]
key.
Press the [ ] or [ ] keys to select
[Dial/Push Phone], and then press the
[ ] key.
Press the [ ] or [ ] keys to select
the telephone line type appropriate
for your telephone ser vice, and then
press the [ ] key.
5
Press the [ ] key to return to
the initial screen.
Selecting the Telephone Network Connection Type
Press the [ ] key.
Press the [ ] or [ ] key s to selec t [Ad -
min. Tools], and then press the [
key.
Press the [ ] or [ ] keys to select
[PSTN / PBX], and then press the [ ]
key.
Press the [ ] or [ ] keys to select
[PSTN] or [PBX], and then press the
[ ] key.
Press the [ ] key to return to
the initial screen.
Setting the Outside Line Access Number
If you have selected PBX, use the following
procedure.
Press the [ ] key.
Press the [ ] or [ ] keys to select
[Admin. Tools], and then press the
[ ] key.
Press the [ ] or [ ] keys to select
[PBX Access Number], and then press
the [
Enter the outside line access number
using the number keys, and then
press the [ ] key.
Press the [ ] key to return to
the initial screen.
] key.
Basic Operation for Sending a
Fax
Press the [ ] key.
]
DHA107
Place the original on the exposure
glass or in the ADF.
Enter the fax number using the
number keys.
Press the [ ] key.
DHA105
Depending on the machine’s settings,
you may be prompted to enter the fax
number again if you manually entered the
destination fax number. In this case, reenter the fax number within 60 seconds,
press [OK ], and then press the [ ] key.
If the fax numbers do not match, go back
to step 3.
If you have more originals to scan,
press [Yes] within 60 seconds, place
the next original on the exposure
glass, and then press [OK]. Repeat this step until all originals are
scanned.
When all ori ginals have been scanned,
press [No] to star t sending the fax.
6
2. Installing the Software
Checking the available connection
•
USB
To install the software over a USB connection, a USB cable and the supplied CD-ROM
are required.
•
Ethernet
•
To install the software over a network connection, a network cable and the supplied
CD-ROM are required.
•
To automatically obtain the IP address, a router with a built-in DHCP server is required.
•
Ethernet and wireless LAN settings cannot be enabled at the same time.
•
Wi-Fi
•
To connect to the network via wireless LAN, see Wi-Fi Settings Guide.
•
To automatically obtain the IP address, a router with a built-in DHCP server is required.
•
Ethernet and wireless LAN settings cannot be enabled at the same time.
•
If WPS cannot be used with SP 213Nw, first connect the machine and computer via a
USB cable, install Smart Organizing Monitor only, and then configure the Wi-Fi settings.
Next, connect the machine to the network, and then install the printer driver only.
7
Loading...