Peerless Industries PRG-1W, PRG-1S, PRG-1 User Manual

Loading...
Peerless Industries PRG-1W, PRG-1S, PRG-1 User Manual

Installation and Assembly Manual:

PRG Precision Gear Projector Mount

Models: PRG-1, PRG-1S, PRG-1W

Features:

ImageLockTM alignment prevents picture sag or drift

Exclusive aluminum track quick release

 

U

 

This product is intended for use with UL

C

US

Listed products and must be installed by a

© L

qualified professional installer.

Maximum UL Load Capacity:

50 lb (22.7 kg)

1 of 13

ISSUED: 08-15-07 SHEET #: 055-9491-6 06-21-10

Visit the Peerless Web Site at www.p erlessmounts.com

For customer care call 1-800-865-2112 or 708-865-8870.

3215 W. North Ave. • Melrose Park, IL 60160 •

(800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum UL Load Capacity. See page 1.

If mounting to wood joist ceilings, make sure that mounting screws are anchored into the center of the joist. Use of an "edge to edge" stud finder is highly recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

This product was designed and intended to be mounted to the following supporting surfaces checked below with the hardware included in this product as specified in the installation sheet. To mount this product to an alternative supporting surface, contact Peerless customer care at 1 800 865-2112.

This product was designed to be installed on the following ceiling construction only;

CEILING CONSTRUCTION

ADDITIONAL HARDWARE REQUIRED

x

Wood Stud

None

x

Wood Joist

None

x

Solid Concrete

None

 

Cinder Block

Contact Customer Service

 

Metal Stud

Do not attach except with Peerless accessory kit for metal studs;

 

 

Contact Customer Service for Peerless accessory kit for metal studs.

 

 

(Not Evaluated by UL)

 

Brick

Contact Customer Service (Not Evaluated by UL)

 

Other or unsure?

Contact Customer Service (Not Evaluated by UL)

Tools Needed for Assembly

stud finder ("edge to edge" stud finder is recommended)

phillips screwdriver

drill

1/4" bit for concrete surface

5/32" bit for wood studs

level

Table of Contents

 

Parts List............................................................................................................................................................................

3

Installation to Extension Columns / Ceiling Plate ..............................................................................................................

4

Installation to Wood Joist Ceilings.....................................................................................................................................

5

Installation to Concrete Ceilings........................................................................................................................................

6

Installation to Threaded Rods............................................................................................................................................

7

Attaching Adapter Plate to Projector..................................................................................................................................

8

Attaching Adapter Plate to Projector Mount.......................................................................................................................

9

Cable Management .........................................................................................................................................................

10

Projector Alignment .........................................................................................................................................................

11

Accessories ...............................................................................................................................................................

12, 13

2 of 13

ISSUED: 08-15-07 SHEET #: 055-9491-6 06-21-10

Visit the Peerless Web Site at www.peerlessmounts.com

For customer care call 1-800-865-2112 or 708-865-8870.

Before you start check the parts list to insure all of the parts shown are included.

Parts List

 

PRG-1

PRG-1S

PRG-1W

 

Description

Qty.

Part #

Part #

Part #

A

projector mount assembly

1

055-1968

055-4968

055-2968

B

4 mm security allen wrench

1

560-9646

560-9646

560-9646

C

#10-32 x 3/8" serrated washer head socket pin screw

2

520-1151

520-2151

520-2151

D

#10-32 x 1/4" socket pin screw

1

520-1196

520-2196

520-2196

E

flat washer

2

540-1078

540-1078

540-1078

F

#14 x 2.5 phillips hex head wood screw

2

5S1-015-C03

5S1-015-C04

5S1-015-C04

G

concrete anchor

2

590-0097

590-0097

590-0097

H

2 mm security allen wrench

1

560-1097

560-1097

560-1097

I

connection block

1

580-1065

580-4065

580-4065

A B

I

C

D

E

F

G

H

NOTE: Actual parts may appear slightly different than illustrated.

3 of 13

ISSUED: 08-15-07 SHEET #: 055-9491-6 06-21-10

Visit the Peerless Web Site at www.peerlessmounts.com

For customer care call 1-800-865-2112 or 708-865-8870.

Installation to Extension Column / Ceiling Plate

1

NOTE: Refer to accompanying instructions with ceiling plates (sold separately) for installing these models to

ceiling.

Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Tighten swivel stop screw against extension column, flush mount tube or reducer using 4 mm security allen wrench (B) as shown in figure 1.2.

NOTE: Swivel stop screw is used to jam against threads of extension column, flush mount tube or reducer to prevent any excess movement of projector mount assembly (A). Do not overtighten screw; overtightening screw will damage threads making it difficult to separate products.

Skip to step 5.

A

1 1/2" EXTENSION COL-

UMN

(SOLD SEPARATELY)

UL LISTED EXT OR AEC

SERIES)

ARROW

INDICATES

FRONT OF

MOUNT

fig. 1.1

CMJ 455

(SOLD SEPARATELY)

SWIVEL STOP

SCREW

fig. 1.2

4 of 13

ISSUED: 08-15-07 SHEET #: 055-9491-6 06-21-10

Visit the Peerless Web Site at www.peerlessmounts.com

For customer care call 1-800-865-2112 or 708-865-8870.

+ 9 hidden pages