Installation and Assembly:
A
Desktop Swivel Mount
Model: HLG442-SB2848-SH, HLG442-SB2848-SH-Q10
Mounting to Desktop Surface
Mounting using Bolt Down Method
NOTE: Read entire instruction sheet before you start installation and assembly.
Parts List
Description Qty Part # Qty Part #
swivel plate assembly 1 090-1977 10 090-1977
B 10-32 x 3/8 flat head screw 4 560-2743 40 560-2743
C 1/4-20 x 1 3/4" elevator bolt 2 560-1764 20 560-1764
D 1/4-20 slope nut 3 530-0035 23 530-0035
E plastic cap 2
F M5 x 6 mm phillips type-F screw 2 520-9504 20 520-9504
G 4 mm allen wrench 1 560-9646 3 560-9646
H #8 split lock washer 2 540-2044 20 540-2044
I M4 flat washer 2 540-2081 20 540-2081
J M4 x 16 mm socket pin serrated washer head screw 2 510-1087 20 510-1087
M4 x 12 mm socket pin screw 2 520-1079 20 520-1079
K
Before you start make sure all parts listed are included with your product.
HLG442-SB2848-SH HLG442-SB2848-SH-Q10
590-1294
590-1294
20
A
B C
D E
H I
F G
J
1 of 4
K
ISSUED: 09-08-10 SHEET #:125-9142-4 09-15-11
Mounting using Bolt Down Method
Choose swivel range below and identify swivel
1
range holes of swivel plate assembly (A).
SWIVEL RANGE HOLE
A
FRONT
Insert two M5 x 6 mm phillips type-F screws (F) into
swivel range holes of swivel plate assembly (A) as
shown below.
F
90° 30°30°
60°
Use swivel plate assembly (A) as a template to mark location of holes, point 1 and point 2, approximately 6.5" apart
2
on table. Drill two holes using a 1/4'' drill bit.
Place two 1/4-20 x 1 3/4" elevator bolts (C) into slots of swivel plate assembly (A).
FRONT
60°
90°
SHOWN WITH 90° OF SWIVEL
AS AN EXAMPLE
C
POINT 1 POINT 2
6.5"
(165 mm)
A
TABLE TOP
2 of 4
A
ISSUED: 09-08-10 SHEET #:125-9142-4 09-15-11
Secure swivel plate assembly (A) to bottom of display base using four at head screws (B) in
3
32" or 42" orientation.
NOTE: Make sure that screws in display base align with slots and holes in swivel plate assembly (A)
as shown below.
DISPLAY
B
BASE SCREWS
32" Display Base Attachment Location
(note orientation of plate to base)
FRONT
FRONT
BOTTOM OF DISPLAY BASE
A
42" Display Base Attachment Location
(note orientation of plate to base)
Hand tighten slope nut (D) through 1/4-20 x 1 3/4" elevator bolt (C) until snug against bottom of desktop surface.
4
Thread another slope nut (D) upside-down, about two turns from rst slope nut (D). Insert an open box wrench
between both slope nuts (D) and tighten. NOTE: Avoid jamming both slope nuts (D) together, doing so may make
it difcult to remove slope nut used for tightening rst slope nut (D) as shown in g 4.1. After slope nut is secure
remove bottom slope nut and add plastic cap (E) as shown in gure 4.2. Repeat with remaining
1/4-20 x 1 3/4" elevator bolt (C).
C
BOTTOM OF DESKTOP
D
Detail 1
C
3 of 4
TIGHTENING
SLOPE NUT
E
FIG 4.1 FIG 4.2
NOTE: Do not overtighten slope nut (D)
plate may distort
ISSUED: 09-08-10 SHEET #:125-9142-4 09-15-11
Installation of Security Screws for Base to Display Attachment
32" Display Base
5
Attach display to base using two M4 x 16 mm socket pin serrated washer head screws (J) into top holes as shown
below. Tighten with 4 mm security allen wrench (L).
Use screws supplied with display for remaining holes.
42" Display Base
Attach display to base using two M4 x 12 mm socket pin screws (K), two #8 split lock washers (H), and two
M4 at washers (I) into bottom holes as shown below. Tighten with 4 mm security allen wrench (G).
Use screws supplied with display for remaining holes.
32" Display Base Attachment Location
(note orientation of screws)
DISPLAY
K
J
DISPLAY BASE
42" Display Base Attachment Location
(note orientation of screws)
DISPLAY
I
H
DISPLAY BASE
NOTE: Display and base may appear
different than illustrated
4 of 4
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 09-08-10 SHEET #:125-9142-4 09-15-11
© 2011, Peerless Industries, Inc. All rights reserved.
Loading...