Installation and Assembly:
Desktop Mount for Shar p 32", 37" and 42" HT3 Models
Models: HL442-HT3, HL442-HT3-S
Maximum Load Capacity:
75 lb (34 kg)
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call
Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
1 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
ISSUED: 02-06-08 SHEET #: 090-9141-1
Before you begin, make sure all parts shown are included with your product.
Parts List
HL442-HT3 HL442-HT3-S
Description qty part # part #
A
race box 1 201-1550 201-1550
B
adapter plate 1 201-1548 201-1548
C
#10 x 3/4" phillips wood screw 4 500-9006 500-9006
D
.156" ID x.16" spacer 1 540-9455 540-9455
E
M5 x 6 mm phillips screw 2 520-9504 520-9504
F
4 mm security allen wrench 1 560-9646 560-9646
G
M5 x 6 mm socket pin serrated washer head screw 1 510-1114 510-1114
H
.257" ID X .5" OD X .5" HT spacer 5 540-1058 540-1058
J
M6 x 30 mm phillips screw 5 510-9109 510-9109
K
M6 x 20 mm socket pin screw 4 N/A 520-9554
L
M6 x 65 mm penta-pin screw 4 N/A 520-1338
M
M5 x 1" penta-pin driver 1 N/A 520-9249
N
flat washer 4 N/A 540-9440
O
split washer 4 N/A 540-9402
Parts may appear slightly different than illustrated.
A
B
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
GH KLM NOJ
2 of 5
C
F
D
E
ISSUED: 02-06-08 SHEET #: 090-9141-1
Rotate the swivel base so large holes in race plate align with mounting holes in swivel base as shown in figure 1.1.
1
Place race plate on mounting surface in the desired location.
Note: See detail 1 for overlap distance of LCD stand from front edge of race box. Dimensions indicated in detail 1
should be the minimum distance from front edge of mounting surface.
Be certain locking tab is facing back then attach swivel base to mounting surface using four wood screws (C) as
shown in figure 1.2.
Note: If swivel restriction is desired, use spacer (D) and screw (C) in hole closest to locking tab, then refer to swivel
restriction option, step 1-1. If swivel restriction is not required, skip to step 2.
fig 1.1
REFER TO THE MINIMUM DISTANCE IN DETAIL 1 BEFORE
DETERMINING LOCATION TO SECURE MOUNT.
ALIGN MOUNTING HOLE
WITH LOCKING TAB
C
fig 1.2
MOUNTING
SURFACE
SPACER (D) IS USED IF
SWIVEL RESTRICTION IS
D
DESIRED
LOCKING TAB
FACES BACK
MOUNTING HOLE IN
SWIVEL BASE
LARGER HOLES IN
RACE PLATE
A
LOCKING TAB FACES BACK
C
MOUNTING
SURFACE
A
DETAIL 1 (Overlap of LCD stand from front edge of race box)
2-1/4"
7/8"
LCD STAND FOR LC-32HT3U
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
LCD STAND FOR LC-37HT3U
3 of 5
LCD STAND FOR LC-42HT3U
ISSUED: 02-06-08 SHEET #: 090-9141-1
1-7/8"
Swivel restriction option
1-1
Race box (A) can be restricted to 10, 30, 60, or 90 degrees of swivel. To restrict swivel, be certain wood screw with
spacer is aligned with locking tab and facing back. Insert two M5 x 6 mm screws (E) into holes on left and right
side for desired degree of swivel restriction.
A
EXAMPLE: INSTALLED
IN HOLES FOR 30°
E
SWIVEL RESTRICTION
90°
60°
30°
10°
KEEP SCREW WITH SPACER ALIGNED
WITH LOCKING TAB FACING BACK.
Chose the correct mounting hole pattern shown in figure 2.1 for mounting adapter plate (B) to LCD stand. Position
2
adapter plate (B) with hook flanges facing bottom and locking tab facing back. Attach adapter plate (B) to LCD
stand using the appropriate number of M6 x 30 mm phillips screws (J) and spacers (H) as shown in figure 2.2.
Note: Remove rubber pads on LCD stand that prevent a flush fit of adapter plate to LCD stand.
fig 2.1
A. LC-32HT3U,
LC-37HT3U
fig 2.2
BACK OF
LCD STAND
A
LCD STAND MAY APPEAR
DIFFERENT THAN
ILLUSTRATED
REMOVE
RUBBER PADS
B
B. LC-42HT3U
H
LOCKING
TAB FACES
BACK
B
B
HOOK
FLANGES
FACE
BOTTOM
J
4 of 5
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
ISSUED: 02-06-08 SHEET #: 090-9141-1
Guide flanges of race box (A) into hook flanges of adapter plate (B).
3
Align holes on locking tabs and secure using M5 x 6 mm socket pin screw (G).
ALIGN HOLES
ON LOCKING
TABS
HOOK
FLANGES
B
FLANGES
G
LOCKING
TABS
A
MOUNTING SURFACE NOT
SHOWN FOR CLARITY
Slide screen onto LCD stand until screen mounting holes and LCD stand mounting holes align as shown in
4
figure 5.1. Attach screen to LCD stand using fasteners that come with your screen.
Security option: Attach screen to LCD stand using four M6 x 20 mm socket pin screws (K), used for the 32" and
37" screens or M6 x 65 mm penta-pin™ screws (L), used for the 42" screen with four split washers (O) and four flat
washers (N) as shown in figure 5.2. Tighten with 4 mm security allen wrench (F) or penta-pin™ driver (M).
fig 5.1
Screen may appear
slightly different
than illustrated
fig 5.2
N
O
K or L
LCD
STAND
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-729-0307 or 708-865-8870.
MOUNTING SURFACE NOT
SHOWN FOR CLARITY
5 of 5
All other brand and product names are trademarks or registered trademarks of their respective owners.
ISSUED: 02-06-08 SHEET #: 090-9141-1
© 2007, Peerless Industries, Inc. All rights reserved.
Loading...