Peerless Industries HDS200 User Manual
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200
HDS200-2
HDS200-3
HDS200-4
®
READY
ISSUED: 07-24-12 SHEET #: 180-9023-1
Contents
Safety Precautions ...........................................................................................................................................4
Proper Care and Safety ....................................................................................................................................4
Unit Care Recommendations ..........................................................................................................................4
Introduction .......................................................................................................................................................5
Features .........................................................................................................................................................5
Package Contents ..........................................................................................................................................5
Product Specifi cations.....................................................................................................................................6
Video Format Supported ................................................................................................................................7
Audio Format Supported ................................................................................................................................7
Wireless Connection ......................................................................................................................................7
WiFi Channel Frequencies .............................................................................................................................7
Transmitter .....................................................................................................................................................8
Receiver .......................................................................................................................................................12
Remote Control ............................................................................................................................................16
Installation and Operation .............................................................................................................................19
Selecting Input and Output Port ..................................................................................................................23
Peer-to-Peer and Multicast LAN (wired) Mode Installation ..........................................................................23
Peer-to-Peer Direct LAN Connection ...........................................................................................................23
LAN Connection Through Router (LAN One-to-One) ...................................................................................24
Confi guring for LAN Through Router (LAN One-to-One) .............................................................................24
Indicator Lights Decoded ..............................................................................................................................25
IR Flasher .....................................................................................................................................................26
IR Extender ..................................................................................................................................................26
Product Modes .............................................................................................................................................26
Peer-To-Peer Modes ....................................................................................................................................26
Multicast Modes ...........................................................................................................................................27
LAN - Wired Connection Mode .....................................................................................................................27
FAQs ................................................................................................................................................................28
Appendix .........................................................................................................................................................30
Warranty ..........................................................................................................................................................34
Contact Information .......................................................................................................................................35
3 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
Safety Precautions
Keep the product out of reach of
children.
If there is any unusual sound, smoke
or odor coming from the product,
immediately unplug the product and
call Peerless-AV Customer Care at
1-800-865-2112.
Do not attempt to open the outer case
of the Transmitter or Receiver. Doing
so will void the product warranty.
Do not insert foreign objects into the
unit.
Make sure to plug the AC power
adapters fi rmly into wall outlets.
Keep the product away from external
heat sources such as heaters or
stoves.
Keep the battery of remote control out
of reach of children.
Keep the remote control away from
humidity and/or liquids.
Do not place the unit on an unstable
surface or in a poorly ventilated area.
Do not use the unit near any fl ammable
substances or combustible sprays.
If any part of the AC power adapter
looks damaged, do not use the product
and immediately call Peerless-AV
Customer Care at 1-800-865-2112.
Proper Care and Safety
Please read this manual before using the product.
Unit Care Recommendations
• Unit can be placed vertically (preferred) or horizontally.
• To clean, use a soft, dry cloth only. Do not use water or other cleaning products as they
may cause electrical failure or damage the surface of the product.
4 of 36
Keep the product unplugged if unused
for an extended period of time.
ISSUED: 07-24-12 SHEET #: 180-9023-1
Introduction
eps
HD Flow Pro Wireless Multimedia Kit provides Full HD 1080p signal transfer, including 3D signal*, without the
hassle of running cables. Create brilliant HD quality multimedia for signage, presentations, or entertainment in
any location,completely un-tethered to your source device!
By simply connecting the Transmitter to a multimedia device such as a computer, set-top box, or Blu-ray™
player and connecting the Receiver to a display device, instant real-time high defi nition digital audio and video
can be placed into in any commercial or residential setting. HD Flow Pro Wireless Multimedia Kit transmits
through walls and fl oors to allow the components to be neatly tucked away in an AV rack or media cabinet,
and is the ideal solution for quick and easy installation where running cable is cost prohibitive or simply not an
option.
* Works with passive 3D signals
Features
• Low latency: ≤ 30ms.
• Supports both digital (HDMI) and analog (Component, Composite) video/audio.
• Supports Wireless or Wired connection - IEEE 802.11n 5 GHz WiFi, LAN connection.
• Two internal antennas (supporting MIMO).
• HDCP v1.1 compliant.
• Supports both DTV & VESA standards: DTV: 1920x1080i60/p60, 1280x720p60, 720x480i60/p60,
VESA : WSXGA+(1680x1050), SXGA(1280x1024), WXGA(1280x800), XGA(1024x768),
SVGA(800x600), VGA(640x480).
• Supports passive 3D content.
• Plug and play setup requires no software programming.
Package Contents
Ensure that the following items are present in the package. If any items are missing or damaged, please call
Peerless-AV Customer Care at 1-800-865-2112 (available 7:00am - 7:00pm CST Monday - Friday).
Transmitter Remote ControlReceiver
Battery Manual
Component
Adapter
AC Adapter (2)IR-Extender
®
READY
Quick Start Guide
PRO WIRELESS MULTIMEDIA KIT
Model No. HDS200 (-2, -3, -4)
2
Minutes
What’s in the Box
1 x Transmitter
1 x IR Extender
1 x Receiver
1 x Component Adaptor
2 x Stand
2 x Power Adapter
1 x Remote Control
1 x Quick Start Guide
1 x IR Flasher
1 x Users Manual
Power/Source
Selection Button
Step 8 Select the output that connects the Receiver to the display using
Installation and Setup
the Power/Source Selection Button or the provided remote control.
The output indicator light will become solid and the HD Flow logo will
Tip The IR window
appear on the display device.
may be easier to
locate with a direct
light shining on
sections of the
front panel of the
component device.
A small flashlight
works well.
Power/Source
Step 1 Connect the Transmitter to the source devices
Step 2 Connect the provided IR Flasher to the IR-OUT port on the Transmitter.
Selection Button
™
Disc player, set top box, gaming console, etc.).
(Blu-ray
Find the location of the IR window on your component device and adhere the
IR Flasher eye directly over the IR window on your component device.
NOTE: One IR Flasher eye is to be used for one component device.
Step 10 Select the desired source or device input on the Transmitter
using the Power/Source Selection Button on the remote control.
Troubleshooting Tips
Transmitter and/or Receiver Indicator Lights are all Blinking:
Tip RepeatSteps
t The HD Flow Pro units are establishing a connection. It can take
3-11 to
up to two minutes for the HD Flow Pro units to establish a complete
more t
connection. If after two minutes have passed and the units have not
Receiv
(HDS20
established a connection, unplug the power cable, wait 30 seconds
HDS20
and reconnect the power supply to the units.
HDS20
Transmitter or Receiver Power Indicator Light is OFF:
Step 3
Step 4 I rovided IR Extender in to
t Check and verify the power supply connection.
to the Receiver.
the IR-IN port on the Receiver and adhering the other end of the IR Extender
to a vertical surface near the output device. Ensure that the IR Extender is in
Transmitter Input Indicator Light Blinks:
a line of sight to the remote control that controls your source devices.
t Make sure that your source device is turned ON and the cable
NOTE: For Multicast models, receivers two, three and four do not come with an IR Extender. Additional IR Extenders
(HDS-IRE) can be purchased separately; visit peerless-av.com for more information.
is properly connected.
t Verify that the Transmitter is set to the appropriate input port.
t Check the resolution from your source device. This may need to
be changed to a resolution supported by the HD Flow Pro Wireless
Multimedia Kit. Reference the Resolution Chart in the HD Flow
Manual for compatibility. Reference your source devices’ manual
for instruction on changing the output resolution.
Receiver Power Indicator Light Blinks:
t Verify that the HD Flow Pro Transmitter and Receiver are within
the recommended range of 131 feet. Physical obstructions such as
walls, floors and ceilings between the Transmitter and Receiver may
decrease the strength of the connection signal and reduce the overall
transmission range.
Step 6 Turn on your display device (TV, monitor, projector, etc.).
S
1. Plug in the power adapter for the Transmitter and the Receiver to nearby
If a connection has been established and the HD Flow logo can be seen
available power outlets.
on the display device, but content is not playing:
2. Plug in the power adapter end to the Transmitter and then to the Receiver.
t Make sure that the input/output cables are properly connected.
3. The units will automatically turn-on. The average power-on/sync time
t Verify that the Transmitter is set to the appropriate input port.
is approximately two minutes.
© 2012 Peerless Industries, Inc. Peerless-AV™ is a trademark of Peerless Industries, Inc. All rights reserved.
HD Flow™ is a trademark of I Do It, LTD. Other parties’ marks are the property of their respective owners. hdflow.com
Step 7 While turning on the display device the HD Flow Pro Wireless Multimedia units will be going through the startup process. This process may
take up to two minutes to complete. The Power/Link indicator lights on the Transmitter and the Receiver will be flashing at first. Flashing indicates
that the units are establishing a secure connection. Wait until the connection is successfully established, indicated by the Power/Link indicator
light becoming solid.
Step 9 Turn on the desired source device that is connected to
the Transmitter.
Step 11 Play the source device content and enjoy up to Full HD 1080p
wireless entertainment experience.
t Check the media source resolution. The display device must be able
to support the resolution of the media source that is being streamed.
Utilizing the INFO button will allow you to see the resolution data that
the dis
resolution of 720p but the source device is outputting 1080p content,
the content needs to be down-scaled to the maximum resolution of the
display device, in this case 720p.
Receiver Output Indicator Light Blinks:
t Make sure that your display device, source device and the HD Flow Pro units
are all turned ON and the Receiver is properly connected to the output device.
t Verify that the Receiver is set to the appropriate output port.
t Check the resolution setting of your source device. This may need to be
changed to a resolution supported by the HD Flow Pro unit. Reference
the Resolution Chart in the HD Flow Pro Manual for compatibility.
Reference your source devices’ manual for instruction on changing
the output resolution.
If the above troubleshooting tips do not resolve the issues for a unicast setup,
please reference the Factory Reset Section of the HD Flow Pro Manual. For a
multicast system configuration, please contact Peerless-AV Customer Care at
800-856-2112 for further instruction.
Stand (2)
User Manual and Installation Guide
Pro Wireless Multimedia Kit
Models:
HDS200
HDS200-2
HDS200-3
®
READY
HDS200-4
ISSUED: 06-12-12 SHEET #: 180-9023-1
IR-Flasher
play device supports. If the display device supports the highest
Warning Do not place the HD Flow
Pro units near other devices that
emit excessive amounts of heat.
Increased temperatures may
cause the HD Flow Pro Transmitter
or Receiver unit to malfunction
or stop working.
Quick Start Guide for HD Flow Pro Wireless Multimedia Kit - LIT-0906
Quick Start Guide
5 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
Product Specifi cations
Video Input (Transmitter)
Video Output (Receiver)
Encoding
Wireless Connection
Wired Connection
LAN
USB
Audio Input
Audio Output
Video Resolution
Streaming Latency
Frequency
LAN Connection
Range
Broadcast
Security
Antenna Type
IR Flasher
IR Extender
Color
Power
HDS200 Models
2 x HDMI up to 1080p (60Hz)
1 x Composite
1 x YPbPr Component
1 x HDMI up to 1080p (60Hz)
1 x Composite
1 x YPbPr Component
H.264 Baseline Profile with Level 4.2
HDCP compliant
Supporting IEEE 802.11n: OFDM
RJ-45 LAN Port
Direct Connection (LAN Cable)
1 x LAN Port (Transmitter and Receiver)
10/100 Base
1 x USB Type A Female (Receiver)
1 x 3.5mm Audio Jack, 1 Stereo RCA Audio Jack (Transmitter)
1 x 3.5mm Audio Jack, 1 Stereo RCA Audio Jack (Receiver)
480i/p, 720p, 1080i/p (24/30/60fps)
< 30ms
5.15 - 5.25GHz
10/100 Base
131ft (40m) maxium
1 Transmitter up to 4 Receivers*
802.1x, 802.11i, WPA2, WPA and WEP 64/128 TKIP AES
2 x Internal Antenna (Transmitter and Receiver)
MIMO Interface
3 IR Flashers
IR-Extender
Black
Voltage: 12VDC
Amps: 2A
Consumption: 12V 2A
*Requires additional Receiver units
6 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
Video Format Supported
• Digital Video
º HDMI - Up to 1080p @ 24Hz, 25Hz, 30Hz, 50Hz, 60Hz
• Analog Video
º Composite – 480i @ 60Hz, 70Hz, 85Hz
º Component – 1080i @ 50Hz, 60Hz, 720p @ 50Hz, 60Hz
º VGA – Up to 1920x1080 @ 50Hz, 60Hz
Audio Format Supported
• Analog
• Digital
• Receiver outputs stereo audio
Wireless Connection
• Peer-to-Peer Mode
• Multicast Wireless Mode
WiFi Channel Frequencies
• Channel 1: 5.19GHz (WiFi Ch 38)
• Channel 2: 5.23GHz (WiFi Ch 46)
Note: WiFi Channels are only active when using Wireless Peer-to-Peer or Multicast modes. The Transmitter
and Receiver have the ability to operate on two WiFi Channels. The default channel is Channel 1, if there is
interference issues on Channel 1 a change to Channel 2 will eliminate most of these issues.
7 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
Transmitter
1
2
3
4
Transmitter Front
8 of 36
5
6
7
ISSUED: 07-24-12 SHEET #: 180-9023-1
Transmitter Front
1. Power/Link Indicator Light
• Blinking indicator light - System booting or establishing link between the Transmitter and the Receiver.
• Quick blinking indicator light - Software upgrading or wireless/LAN mode switching.
• Solid indicator light - Link between the Transmitter and Receiver has been established and is ready for
signal transmission.
2. HDMI 1
• The HDMI 1 indicator light will be illuminated when the HDMI 1 port is selected for video input.
• If there is no signal, and/or the cable is not connected, the indicator light will blink.
3. HDMI 2
• The HDMI 2 indicator light will be illuminated when the HDMI2 port is selected for video input.
• If there is no signal, and/or the cable is not connected, the indicator light will blink.
4. PC
• The PC indicator light will be illuminated when the PC In port is selected for video input.
• If there is no signal, and/or the cable is not connected, the indicator light will blink.
5. AV
• The AV indicator light will be illuminated when the AV In port (Composite) is selected for the video input.
• If there is no signal, and/or the cable is not connected, the indicator light will blink.
6. IR Window
• IR receiving window enables remote control of components.
7. Power/Source Selection Button
• Press and hold for 3 seconds to turn on the unit.
• When powered on:
º Press to select the video input source. Each press of the button will cycle through the available
video input "HDMI1→ HDMI2→ PC→ AV →HDMI1" in sequence.
º Press and hold for 8 seconds to turn the unit off.
9 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
2
1
3
4
5
6
Transmitter Back
10 of 36
7
8
ISSUED: 07-24-12 SHEET #: 180-9023-1
Transmitter Back
1. HDMI 1 IN
• HDMI1 input port
2. HDMI 2 IN
• HDMI2 input port
3. AV-IN
• Composite input port
4. IR-OUT
• Connects IR Flasher to the Transmitter for remote control of external devices which are connected to the
Transmitter (i.e. Blu-Ray player, DVD, STB, etc).
5. PC AUDIO-IN *
• Stereo audio input port
6. PC-IN (VGA)**
• Supports component input with included Component Adaptor
7. LAN
• LAN connection is used for the following:
º Direct connection to LAN cable for LAN installations.
º Direct connection to PC for system confi guration settings.
8. DC
• DC power input
* For the audio part of a component media source, use the PC Audio input port with a 3.5mm to RCA cable
(not included).
** If using the PC Video input port for component (YPbPr) media source, use the included component to VGA
adapter.
11 of 36
ISSUED: 07-24-12 SHEET #: 180-9023-1
Loading...