|
Panasonic |
|
Video Cassette Recorder |
OmnivlBtr» MI5 |
Operating Instructions |
|
Models No. PV-V4611 |
Connections and Initial Setup Procedures are on pages 8 to 11.
As an EN€f*5Y STAR^ P^fXiUk’ MatsasMa Efedre Corponoonof
Amehcahas thatfhw p-oajd / - j_naif^ or pfO(/ud moM meetstfta €N£fVSY
STAÌÌ^ guóiabneslor energy etheteecy ___________________
Ptease read these mstructons carefully before attefnpl/og to connect operate or ad|ust this product Please save this manual
Spanish QuKk Use Guide is indudeO. (Guia para rapida oor^suita en esilino) està irKluida ) LSOTOMTA
E BSEI
FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING IN STRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT
INSTALLATION
POWER SOURCE CAUTION
Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.
2POLARIZED OR GROUNDING PLUG
As a safety feature, this Video product comes with either a polarized power cord plug (one blade is wider than the other), or a three-wire grounding type plug.
POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot fully insert the plug, try reversing it. If it still will not fit, have an electrician instail the proper wall outlet. Do not defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet, ft necessary, have an electrician install the proper outlet. Do not defeat the safety feature by tampering with the plug.
3POWERCORD
Make sure power cords are routed so that they are not likely to have anything rest on them, roll over them, or be in the way of walking traffic. If an extension cord is used, make sure It also has either a polarized or grounded plug and that the cords can be securely connected. Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified service technician. Overloaded outlets and extension cords are fire hazards and should be avoided.
4DONOTBLOCKVENTILATONHOLES Ventilation openings In the cabinet release heat generated during operation. If they are blocked, neat build-up inside the unit can cause failures that may result in a fire hazard or heat damage to cassettes. For protection, follow these rules:
a.Never cover ventilation slots or the unit while in use, or operate the unit when placed on a bed, sofa, rug, or other soft surface.
b.Avoid built-in installation, such as a book case or rack, unless proper ventilation is provided.
5AVOID EXTREMELY HOT LOCATIONS OR SUDDENTEMPERATURECHANGES
Do not place the unit over or near any kind of heater or regulator, in direct sunlight, inside a closed vehicle, etc,. Do not move the unit suddenly between areas of extreme temperature variation. If the unit is suddenly moved from a cold place to a warm place, moisture may condense in the unit and on the tape.
6TOAVOIDPERSONALINJURY
•Do not place unsecured equipment on a sloping surface.
•Do rx)t place this unit on any support that is not firm, level, and adequately strong. The unit could fall causing serious Injury to a child or adult
агк1 damage to the unit.
•An appliance and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
•Carefully follow all operating instructions and use the manufacturer's recommended accessories when operating this unit or connecting it to any other equipment.
OUTDOOR ANTENNA INSTALLATION |
1 |
SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the equiprrient, be sure the antenna or cable system is grounded so as to provide some protection against tauift up static cHarges
and voltage surges. Section 810 of the National Electrical
Code, ANSl/NFPA 70 (in Canada, part 1 of the Canadian Electrical Code) provides infonnation
with respect to proper grounding of the mast and supporting
structure, groundirra of the lead-in iwiie
to an antenna disrfiarge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode.
KEEP AMTENNACLEAR OFHIGH VOLTAGE POWER UNESORORCUnS An outside antenna ^stem should be located well away from
power lines, electric light or power dioiits and where it wilt never come Into contact wttn these power sources if it should happen to fall. When installing an outside antenna, extreme care should be taken to avoid touching power lines, drcuits or other pov^r sources as this could Be fatal. Because of the hazards Involved,
antenna installation should be left to a professional. : USING THE VIDEO UNIT
f the unit has been in stor^e or moved to a new location, refer first to the INSTALLATION section of these safeguards,
1KEEPTHIS VIDEO UNIT AWAY FROM WATER OR MOISTURE OF ANY KIND.
2IFEOUIPMENTISEXPOSEDTORAIN, MOISTURE,OR STRONG IMPACT, unplug the unit and have It inspected by a qualified service technician before use.
3DURINGANELECTRICALSTORM
During a lightning storm, whether indoors or outdoors, or before leaving the unit unused for extended periods of time, disconnect air equipment from the power source as well as the antenna and cable system.
4WHENTHEUNITIS PLUGGED IN
*Never expose the unit to rain or water. DO NOT OPERATE if liquid has been spilled into the unit. Immediately unplug the unit, and have it inspected by a service technician. Fire and shock hazards can result from electrical shorts caused by liquid contact inside.
*Never drop or push any object through openings in the unit. Some internal parts carry hazardous voltages and contact can cause electric shock or fire hazard.
*Avoid placing the unit directly above or below your TV set as this may cause electrical interference. Keep all magnets away from electronic equipment.
5USING ACCESSORIES
Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.
6CLEANINGTHEUNIT
Unplug the unit. Then, use a dean, diy, chemically untreated cloth to gently remove dust or debris, DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into the unit and cause electrical shock. Any substance such as wax, adh^ive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect intetnal parts.
: |
SERVICE |
Z1 |
1DONOTSERVICETHISPRODUCTYOURSELF
If, after carefully following the detailed operating instruc tions, this Video product does not operate properly, do not attempt to open or remove covers, or make any adjust ments not described in the manual. Unplug the unit and contact a qualified service technician.
2IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by the manufacturer, or those having the same safety charactenstics as the original parts. The use of unauthorizeci substitutes may result in lire, electric shock, or other hazards.
3HAVETHESERVICETECHNICIAN PERFORM ASAFETYCHECK After any service or repairs to the unit, request the service technician to conduct a through safety check as described
in the manufacture’s service literature to insure that the video unit is in safe operating condition.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement: Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive.
Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
A |
|
|
|
A |
|
CAUTION |
|
||
|
|
|
|
|
|
RISK OF ELECTRIC SHOCK |
|
||
|
|
DO NOT OPEN |
|
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
Note to CABLE system installer:
This reminder is provided to call the CABLE system installer’s attention to Article 820-40 of the NEC in USA (and to the Canadian Electrical Code in Canada) that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
FCC Warning: Any unauthorized changes or modifications to this equipment would void the user’s authority to operate.
on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below.
The serial number is on the tag located on the back of your VCR.
•Date of Purchase _______________________
Dealer Purchased From Dealer Address________
Dealer Phone No.______
Model No. ___________
Serial No. ____________
□Remote Control
LSSQ0286
To order accessories, call toll free 1-800-332-5368.
Break off the tab to prevent recording.
Record Tab
Screw driver
Only use tapes with the IVH^ mark in this unit.
1) Open cover.
2) Insert batteries as marked.
3) Close cover.
•Do not mix old and new batteries.
•Do not mix alkaline with manganese batteries.
Tape Speed |
|
Type of Video Cassette |
||
|
|
|
|
|
Setting |
|
T60 |
T120 |
T160 |
SP |
|
1 Hour |
2 Hours |
2 Hours |
|
40 Minutes |
|||
(Standard Play) |
|
|||
|
|
|
|
|
|
|
|
|
|
LP |
|
2 Hours |
4 Hours |
5 Hours |
(Long Play) |
|
20 Minutes |
||
|
|
|
||
|
|
|
|
|
SLP |
|
3 Hours |
6 Hours |
8 Hours |
(SuperLongPlay) |
|
|||
|
|
|
|
|
For assistance, please call : 1-800-211-PANA{7262) or send e-mail to : consumerproducts@panasonic.com
Table of Contents |
|
Important Safeguards and Precautions...................................... |
2,3 |
Accessories...................................................................................... |
4 |
Loading the Batteries..................................................................... |
4 |
Prevent Accidental Tape Erasure................................................... |
4 |
Record/Playback Time..................................................................... |
4 |
Location of Controls..................................................................... |
6,7 |
Initial Setup for ANT^Cable-VCR-TV Connection...................... |
8,9 |
Initial Setup for DSS/Cable Box-VCR-TV Connection |
... 10,11 |
Reset Language, Channels, Clock, VCR’s Output Channel .... 12,13 |
|
Playback a Tape............................................................................. |
14 |
Record On a Tape.......................................................................... |
15 |
Timer Recording ....................................................................... |
16,17 |
Timer Recording Using VCR Plus+®System........................... |
18,19 |
Multi-Brand Control Feature............................. |
. 20,21 |
Advanced Connections (Cable/DSS)............... |
..... 22 |
MTS Broadcast/ VMS Hi-Fi Stereo System |
..... 23 |
Tape Operation (Search System)..................... |
24-26 |
Special VCR Features........................................ |
. 26,27 |
Copying Your Tapes (Dubbing)........................ |
..... 28 |
VCR & Cassette Information................... |
................29 |
On-Screen Displays (OSD)...................... |
................30 |
Before Requesting Service..................... |
............... 31 |
Service Center List.................................. |
................32 |
Warranty.................................................... |
................33 |
Spanish (Español) Quick Use Guide. |
...........34,35 |
Index.......................................................... |
Back Cover |
EJECT |
LiGHT |
|
POWER |
TV mode |
|
VCR mode |
DSS/CABLE mode |
|
VCR/TV — |
INPUT |
|
PLAY |
FAST FORWARD/SEARCH |
|
SELECT UP |
SET |
|
REWIND/SEARCH |
PROGRAM/ VCR+ |
|
|
||
SET |
STOP |
|
ACTION -------------- |
SELECT DOWN |
|
|
||
NUMBER KEYS |
ADD/DELETE |
|
TAPE POSITION |
||
COUNTER RESET |
||
DISPLAY |
||
|
||
PAUSE/SLOW |
SEARCH/ ENTER |
|
CM/ZERO |
SPEED |
|
RECORD |
||
SAP/ Hi-Fi |
||
|
||
VOLUME UP/DOWN |
CHANNEL UP/ DOWN |
|
TRACKING/ V-LOCK |
||
|
||
Light Tower Universal Remote Control |
|
Light button: When LIGHT is pressed, available buttons in the selected nnode light up and the selected mode button {TV/VCR or DSS CABLE) flashes for 5 seconds. If no button is pressed, light goes out in 5 seconds to conserve batteries. Also, by holding down a button, you can confirm the selected mode {mode button will flash) in the dark.
EJECT button: Press to eject tape from VCR. If EJECT is pressed during record,
VCR will not respond.
Cassette Compartment VCR/TV selector PLAY
POWER |
|
|
|
|
FAST |
Video |
|
FORWARD/ |
|
SEARCH |
|
Input |
|
|
Connector |
|
\ REWIND/ |
|
|
|
Audio Input |
Remote |
SEARCH |
Connector |
CHANNEL UP/ DOWN Sensor |
RECORD STOP/EJECT |
(UR) |
TRACKING/ V-LOCK |
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to ; consumerproducts@panasdnic.com
|
Timer Indicator |
|
|
|
Lights when the VCR is set for a Timer |
||
Power Indicator |
Recording, or when One Touch Recording |
||
(OTR) is used. Flashes when a Timer |
|||
Lights when power |
|||
Recording is set, but a tape has not been |
|||
is on. |
|||
inserted into the VCR and when a power |
|||
|
|||
|
interruption occurs during Timer Programming. |
||
|
|
VCR Indicator |
|
|
|
Lights when the |
|
|
|
VCR/TV selector is |
|
|
|
set to VCR. |
|
Clock/ Status/ Channel/ Speed Display |
|
||
Displays the current time. Briefly displays VCR |
|
||
status when a function button is pressed. Briefly |
Hi-Fi Indicator |
||
displays the channel number, or “LI” or “L2” |
Lights when Hi-Fi audio is |
||
when a channel or line input is selected. Briefly |
|||
monitored in Playback |
displays the recording speed when SPEED is |
Mode. |
|||
pressed. |
||||
|
||||
|
|
|
||
|
Rear View of the VCR |
|
|
|
AC Power Plug |
|
InitialSetupforAisn/Cable-VCR-TVConnection
How to Connect
|
Connect the Cable from Antenna/Cable to the IN FROM ANT. |
(D terminal on VCR. |
|
2 |
Connect the OUT TO TV terminal on the rear of VCR to the ANT. |
IN terminal on TV using the RF Cabie (included accessory). |
How to do Initial Setup
1 |
Press VCR* for VCR mode. Turn |
the TV on and set it to channel 3. |
2 Turn VCR on.
When VCR is turned on the first time, SELECT LANGUAGE screen appears.
3Press CHA to select English, or
Press CHV to select Spanish, or
Press VCR/TV key to seiect French. When one of above keys is pressed, SELECT CONNECTiON screen is dispiayed in the selected language.
|
|
n^R I CLOCK I CHANNEL |
|||
|
|
|
CABLE/DSS BOX^VCR^TV |
||
|
|
|
VCR»-CABLE/(JSS BOX»TV |
||
|
|
|
SELECT:* r |
||
If screen does not appear, check |
|
|
EXIT : ACT I ON |
||
Press A ▼ to select connection |
|||||
connection between VCR and TV |
|||||
and, if TV is tuned to channel 3, try |
and press ► to set. |
||||
switching it to channel 4. |
4CHANNEL7CLOCK AUTO SET |
||||
When you want to change the output |
screen appears. |
||||
channel of VCR, please refer to VCR’s |
|
|
|
|
|
Output Channel on page 13. |
|
rvCR I CLOCK I CHANNETI |
|||
If wrong language is set, do “Reset All |
|
||||
|
|
WEL/CUKK AUTO SET |
|
||
VCR Mennory Functions” steps on |
|
|
|
||
|
|
AND IF YOU USE A CABLE |
|||
page 9. |
|
|
|||
|
|
|
CONNECT ANTENNA CAGLE |
||
r WARNING-------------------------------------------------------------------- |
|
BOX, TUNE IT TO YOUR |
|||
|
LOCAL PBS CH THEN. . , |
||||
|
|
|
|||
When using "Nut type" RF coaxial cables, tighten with fingers |
|
PLEASE PRESS CH UP KEY |
only. Overtightening may damage terminals.
8 |
For assistance, please call ; 1-800-211-PANA{7262) or send e-mail to : consumerproducts@panasonic.com |
|
'Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
5 Press CHA Key to start Channel/Clock Auto Set operation. Settings are performed automatically. If the setup is completed, the following screen is displayed.
VCH r&LOCKI &HANNEL
[171372001 SUM 2:20PU
DST:ON SETTJNG : CH 10
If “Auto Clock Set is Incomplete" screen appears, set the clock using MANUAL CLOCK SET procedure shown below.
Pvcn I CLOCK I CHANNEL
ALTTO CLOCK SET IS
INCOMPLETE
POWER
VCR
VCR/TV
SELECT/ SET
A :PLAY T :STOP
◄;REW
► :FF
ACTION
CH A/V
Manual Clock Set
If Auto Clock Set was incomplete, manually set the clock as follows.
1 Press ACTION Key on the Remote to display CLOCK Menu screen.
rv'cn I CLOCKl CHANNEn
SELECT MONTH
SELECT:* T SET:
LeXIT : ACT I ON
2 Press A T to select the month and ► to set. In the same manner, select and set the date, year, time, and DST (daylight saving time).
rvCH I CLOCK I CHANNETj
11/11/2001 SUN 12:00PM
OST:ON
SET COMPLETED
SET ►
START : ACT I ON
3 Press ACTION Key twice to start CLOCK and exit.
Reset All VCR Memory Functions
Use when moving VCR to new location, or if a mistake was made in the Initial Setup section.
•Make sure a tape is not inserted in the VCR.
Press and hold both
PLAY and CHANNEL
A on the VCR for more than 5 seconds.
• The power shuts off.
Do “Initial Setup” on page 8.
InitiaiSetupforDSS/CableBox-VCR-TVConnection
How to Connect
Connect the OUT Jack on your cable box to the IN FROM ® ANT. terminal on the VCR with an RF cable.
2 Connect the OUT TO TV terminal on the rear of VCR to the ANT.
IN terminal on TV using the RF Cable (included accessory).
How to do Initial Setup
1 |
Press VCR* for VCR mode. Turn |
the TV on and set it to channel 3. |
When VCR is turned on the first time, SELECT LANGUAGE screen appears.
SEL£CT LANGUAGE
IPRESS CH A : ENGLISH
OPRIMIR CH » : ESPAÑOL
APP. VCFVTV ; FRANÇAIS
TO CHANGE VCR' S OLFTPUT
PRESS ACTION KEY.
3 Press CHA to select English, or
Press CHV to select Spanish, or
Press VCR/TV key to select French. When one of above keys is pressed, SELECT CONNECTION screen is displayed in the selected language.
I VCR rO-OCK fCHAN NEL
SELECT CONNECTION
VCR TV
'Alili
VCRK CABLE/DSS BOXKTV
If screen does not appear, check connection between VCR and TV and, if TV is tuned to channel 3, try switching it to channel 4.
When you want to change the output channel of VCR, please refer to VCR’s Output Channel on page 13.
If wrong language is set, do “Reset All VCR Memory Functions’* steps on page 9.
4Press A ▼ to select “CABLE/DSS BOXP-VCRP-TV” connection and press ► to set.
ryc^ rCLC^fCHANNEL
SELECT CONNECTION
CABLE/DSS BOXAVCRATV
CABLE/PSS BOX OUTPUT CH
r WARNING--------------------------------------------------------------------
When using "Nut type” RF coaxial cables, tighten with fingers only. Overtightening may damage terminals.
10 |
For assistance, please call : 1*800'211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com |
|
‘Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Confirm the output channel of your cable |
|
|||
box or DSS receiver. Press CH A ▼ Keys |
|
|||
5to select the same channel as the cable |
|
|||
box or DSS receiver output channel. |
|
|||
Press ► to enter. |
|
|||
|
VCR I CLOCK I CHANNEL I |
POWER |
||
|
|
|||
|
CH.i\!JNEUCLOCKAUTOSET |
|
VCR |
|
|
CONNECT Am'ENNA CABLE |
|||
|
AND IF YOU USE A CABLE |
|||
|
BOX. TUNE IT TO YOUR |
VCR/TV |
||
|
LOCAL PBS CH THEW,.. |
|||
|
|
|||
|
PLEASE PRESS CH UP KEY |
SELECT/ |
||
|
|
|
SET |
|
|
|
|
A:PLAY |
|
Turn on your cable box and set it to |
▼ :STOP |
|||
your Public Broadcasting Station |
►:FF |
|||
(PBS) channel in your time zone. |
ACTION |
|||
If you use DSS receiver, it must be |
||||
|
||||
turned off. |
|
|||
Press CH A Key to start Channel/Clock |
CH A/T |
|||
Auto Set operation. The Channel/Clock |
|
|||
6Setting is performed automatically. |
|
|||
If the setup is completed, the following |
|
|||
screen appears. |
|
|||
f~7cR r CLOCK 1 CHANNEL |
|
|||
|
5/137M01 SUN 2:20PH| |
|
||
|
D5T:ON |
|
||
|
CH 10 |
|
||
|
AUTO CLOCK SET |
|
||
|
COMPtETEO |
|
||
If “Auto Clock Set is Incomplete" |
|
|||
screen appears, set the clock using |
|
|||
MANUAL CLOCK SET procedures |
|
|||
shown on page 9. |
|
|||
|
VCR [TLOCtTI CHÀKÌNEL |
|
11
1 |
»VCR I f-L.OCK I CHANNEin |
|
REPEAT PLAY |
;OFF |
|
REMOTE WARNING :0N |
|
|
AGTO SHUT-OFF :ON |
|
|
IDfOMAAANGUE; ENGLISH |
VCR'S OUTPUTCH :3
SELECT ; A ▼ A ►
EXIT ; ACT I ON
to display menu.
2 |
■ Language |
Press AT to select |
|
1)language item. |
VCR 1 ncLOCtn CHANNEL
REPEAT PLAY :0FF
REMOTE WARNING :ON
VCR’ S OUTPUT CH :3
SELECT:A T SET:»
EXIT ; ACTION_____________
■Channels
1) Press ^ ► to select CHANNEL.
Г“/CR fCLOCK I» CHANNEL "AriTENNA A : CABLE
AUTO SET
WEAK SIGNAL DISPLAY : OFF CABLEOSS BOX SET UP VCR Plus* CH SET UP
SELECT
EXIT [ACTION
2) Press ► repeatedly.
VCR i "CLOCKI CHANNEL
REPEAT PLAY OFF
REMOTE WARNING '.ON
AUTO SHUTOFF
VCR’S OUTPUT CH
SELECT:» |
▼ |
SET:» |
EXIT :ACTtON |
|
|
For English
PVCR
REPETICION [INAIкСТ] ^VISO(CONT.RËMOTO) [ACT
IAN AL DE SALIDA :3
ELEGIR : ж ▼ FIJAR : ►
SALIR [ACTION
For Spanish
“MAG NETOn HORLTI "CANALI
REPRISE LECTURE
HESSAGE O' ERREUR
CA SORTIE [ 3
SEL. [A ▼ REGLER:»
.QUIITER-ЗАСЛОН____
For French
3) Press ACTION to exit.
2)Press AT to select “ANTENNA," then
press ► to set your antenna system
(TV or CABLE).
AUTO SET
WEAK SIGNAL DISPLAY : OFF
CABLE/DSS BOX SET UP
VCR P*us+ CH SET UP
SELECT [A T SET:
EXIT [ACTION___________
3)Press AT to select
"AUTO SET,” then press ►.
•If you use a cable box, set it to the PBS channel in your time zone.
I VCR I CLOCK I CHANNEL |
CONNECT ANTENNA CABLE
AND IF YOU USE A CABLE
BOX, TUNE IT TO YOUR
LOCAL PBS CH THEN, . .
PLEASE PRESS CH UP KEY
(This screen appears only when auto clock is set.)
4) Press CH A.
•After Channel Auto Set is finished, Clock Auto Set will be performed.
■ Clock
1 ) Press ◄ ► to select CLOCK.
rVCR |
CHANNEL |
'"AUTO CLOCK SET |
|
MANUAL |
|
TIME ZONE ADJUST : 0 |
|
SELECT : A ¥ A ►
EXIT [ACTION
2)Press AT to select MANUAL and press ►.
(For Auto Clock Set, select “AUTO CLOCK SET,” then press CH A.)
["rfCR [~CL66KÌ TAUTÎTCLOCK SET
TIME ZONE ADJUST : 0
SELECT:» ¥ SET:»
EXIT [ACTION_______________
("TIME ZONE ADJUST appears only when auto clock is set.)
I VCR I CLOCK I CHA^EiTI
11/11/2001 SUN;I2HPK
SELECT HOUR |
|
|
|
SELECT:» |
¥ |
SET[< |
» |
EXIT : ACTION |
|
|
|
3)Press AT and ◄ ► to select and set the date, time, and DST (Daylight Saving Time).
4)Press ACTION twice to start the clock and exit this mode.
12 |
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com |
|