Panasonic CQ-VD7003W2, CQ-VD7003W3, CQ-VD7003W4, CQ-VD7003W5 Operating Instructions Manual
1
2
CQ-VD7003W
English
Safety Information
Warning
Observe the following warnings when using
this unit.
❑
The driver should neither watch the display nor
operate the system while driving.
Watching the display or operating the system will distract
the driver from looking ahead of the vehicle and can cause
accidents. Always stop the vehicle in a safe location and
use the parking brake before watching the display or operating the system.
❑
Use the proper power supply.
This product is designed for operation with a negative
grounded 12 V DC battery system. Never operate this
product with other battery systems, especially a 24 V DC
battery system.
❑
Keep batteries and insulation film out of reach of
infants.
Batteries and insulation film can be ingested, so keep them
out of the reach of infants. If an infant ingests a battery or
insulation film, please seek immediate medical attention.
❑
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair
the product yourself. If the product needs to be repaired,
consult your dealer or an authorized Panasonic Service
Center.
❑
Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an
abnormal state (has foreign objects in it, is exposed to
water, is smoking, or smells), turn it off immediately and
consult your dealer.
❑
The remote control unit should not lie about in the
car.
If the remote control unit lies about, it could fall on the
floor while driving, get wedged under the brake pedal, and
lead to a traffic accident.
❑
Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it
replaced with the fuse prescribed for this unit by a qualified
service engineer. Incorrect replacement of the fuse may
lead to smoke, fire, and damage to the product.
Observe the following warnings when
installing.
❑
Disconnect the lead from the negative (–) battery
terminal before installation.
Wiring and installation with the negative (–) battery terminal connected may cause electrical shock and injury due to
a short circuit.
Some cars equipped with the electrical safety system have
specific procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO
THE UNINTENDED ACTIVATION OF THE ELECTRICAL
SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH.
❑
Never use safety-related components for installation, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank,
brake, suspension, steering wheel, pedals, airbag, etc.) for
wiring or fixing the product or its accessories.
❑
Installing the product on the air bag cover or in a
location where it interferes with airbag operation
is prohibited.
❑
Check for piping, gasoline tank, electric wiring,
and other items before installing the product.
If you need to open a hole in the vehicle chassis to attach
or wire the product, first check where the wire harness,
gasoline tank, and electric wiring are located. Then open
the hole from outside if possible.
❑
Never install the product in a location where it interferes with your field of vision.
❑
Never have the power cord branched to supply
other equipment with power.
❑
After installation and wiring, you should check the
normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may
cause fire, electrical shock or a traffic accident.
❑
In the case of installation to an airbag-equipping
car, confirm warnings and cautions of the vehicle
manufacturer before installation.
❑
Make sure the leads do not interfere with driving
or getting in and out of the vehicle.
❑
Insulate all exposed wires to prevent short circuiting.
This pictograph intends to alert you to the presence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in severe injury or
death.
■
Read the operating instructions for the unit and all other
components of your car audio system carefully before using
the system. They contain instructions about how to use the
system in a safe and effective manner. Panasonic assumes
no responsibility for any problems resulting from failure to
observe the instructions given in this manual.
■
This manual uses pictographs to show you how to use the
product safely and to alert you to potential dangers resulting
from improper connections and operations. The meanings of
the pictographs are explained below. It is important that you
fully understand the meanings of the pictographs in order to
use this manual and the system properly.
Warning
This pictograph intends to alert you to the presence of important operating instructions and
installation instructions. Failure to heed the
instructions may result in injury or material damage.
Caution
2
3
CQ-VD7003W
English
Caution
Observe the following cautions when using
this unit.
❑
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and
traffic conditions while driving.
❑
Do not insert or allow your hand or fingers to be
caught in the unit.
To prevent injury, do not get your hand or fingers caught in
moving parts or in the disc slot. Especially watch out for
infants.
❑
This unit is designed for use exclusively in automobiles.
❑
Do not operate the unit for a prolonged period with
the engine turned off.
Operating the audio system for a long period of time with
the engine turned off will drain the battery.
❑
Do not expose the unit to direct sunlight or excessive heat.
Otherwise these will raise the interior temperature of the
unit, and it may lead to smoke, fire, or other damage to the
unit.
❑
Do not use the product where it will be exposed to
water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead
to smoke, fire, or other damage to the unit. Make especially
sure that the unit does not get wet in car washes or on
rainy days.
Observe the following cautions when
installing.
❑
Refer wiring and installation to qualified service
personnel.
Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer.
Panasonic is not liable for any problems resulting from
your own installation of the unit.
❑
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire
the product could cause an accident or fire.
❑
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent
them from getting caught in the vehicle chassis, screws,
and moving parts such as seat rails. Do not scratch, pull,
bend or twist the leads. Do not run them near heat sources
or place heavy objects on them. If leads must be run over
sharp metal edges, protect the leads by winding them with
vinyl tape or similar protection.
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools
to install the product. The use of parts other than those
supplied or designated may result in internal damage to the
unit. Faulty installation may lead to an accident, a malfunction or fire.
❑
Do not block the air vent or the cooling plate of the
unit.
Blocking these parts will cause the interior of the unit to
overheat and will result in fire or other damage.
❑
Do not install the product where it is exposed to
strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If
the installation is not stable, the unit may fall down while
driving and this can lead to an accident or injury.
❑
Installation Angle
The product should be installed in a horizontal position
with the front end up at a convenient angle, but not more
than 30˚.
The user should bear in mind that in some areas there may
be restrictions on how and where this unit must be
installed. Consult your dealer for further details.
❑
Wear gloves for safety. Make sure that wiring is
completed before installation.
❑
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
❑
Do not connect more than one speaker to one set
of speaker leads. (except for connecting to a
tweeter)
Observe the following cautions when handling
the battery for the remote control unit.
●
Use only specified battery (CR2025).
●
Match the polarity of the battery with the (+) and (–) marks
in the battery case.
●
Replace a dead battery as soon as possible.
●
Remove the battery from the remote control unit when not
using it for an extended period of time.
●
Insulate the battery (by placing them in a plastic bag or
covering them with vinyl tape) before disposal or storage.
●
Dispose of the battery according to the local regulations.
●
Do not disassemble, recharge, heat or short the battery. Do
not throw a battery into a fire or water.
In case of battery leakage
●
Thoroughly wipe the battery liquid off the battery case and
insert new battery.
●
If any part of your body or clothing comes into contact
with battery liquid, wash it with plenty of water.
●
If battery liquid comes into contact with your eyes, wash
them with plenty of water and get immediate medical attention.
CAUTION:
• PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR WIRING,
INSTALLATION, AND USE OF THIS UNIT AND THE DEVICES TO BE CONNECTED.
3
4
CQ-VD7003W
English
Safety Information (continued)
Caution
THIS PRODUCT IS A CLASS ILASER PRODUCT.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
This system is designed so that you
cannot see moving pictures while
you are driving.
¡
Park your car in a safe place and pull the side
brake (parking brake) lever before watching the
monitor.
¡
A rear monitor (option) displays moving pictures while driving.
Note:
¡
Be sure to connect the side brake (parking
brake) connection lead. (a Installation
Instructions)
4
5
CQ-VD7003W
English
Notes on Use
Components
Before Reading These Instructions
4. Operating Instructions
<YFM284C564ZA>
Qty.: 1
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
3. Wiping Cloth
<YEFX9991793>
Qty.: 1
2. Remote Control Unit
<EUR7641060>
(includes a battery: CR2025)
Qty.: 1
CAR AV
MUTE
ENT
VOL
SRC
PWR
DVD MENU
RET
RETURN
TOP MENU
ENTER / BAND
1. Main Unit
(LCD monitor/DVD player)
Qty.: 1
ENTER
TILT O/C
ASP
MUTE
SRC MENU
CQ-VD7001U
NAVI
OPEN / CLOSE
ASPECT
PWR
VOL
P·MODE
DISC
TUNE /
TRACK
OPEN / CLOSE
CQ-VD7003W
TILT
TEXT
Note:
¡The number in parenthesis underneath each accessory
part name is the part number for maintenance and
service.
¡Accessories and their parts numbers are subject to
modification without prior notice due to improvements.
7. Installation Hardware (screws,
cords, etc.)
(a Installation Instructions)
6. Installation Instructions
<YFM294C067ZA>
Qty.: 1
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
5. System Upgrade Guidebook
<YFM284C565ZA>
Qty.: 1
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
OO-OOOOO
Liquid Crystal Panel
¡Do not cause impact to the liquid crystal panel.
¡Usage temperature range: 0 °C to 40 °C
When the temperature is very cold or very hot, the
image may not appear clearly or may move slowly.
Also, movement of the image may seem to be out of
synchronization or the image quality is not malfunction or problem.
¡In order to protect the liquid crystal panel, keep it out
of direct sunlight while the unit is not in use.
¡Sudden changes in the temperature inside the car such
as those which occur immediately after the car’s air
conditioner or heater has been turned on may cause
condensation (droplets of water) to form and, as a
result, the panel may not work properly. Do not use
the unit while these symptoms are in evidence but
leave the unit standing for about and hour, and then
resume or start use.
This operating instruction manual is for 4 models CQ-VD7003W2/CQ-VD7003W3/
CQ-VD7003W4 and CQ-VD7003W5.
The following table shows the playable region number for each model.
5 (ALL)CQ-VD7003W5
4 (ALL)CQ-VD7003W4
3 (ALL)CQ-VD7003W3
2 (ALL)CQ-VD7003W2
Playable region numberModel
Differences Among 4 Models
Example:
“Before Disc Playback”
(a page 16)
2 3 4
ALL
5
5
6
CQ-VD7003W
English
Features
■ Simultaneous Multi-Device Connection
(with Expansion Module (hub unit))
You can connect the optional Expansion Module (hub
unit) (CY-EM100N). Connection of the Expansion
Module allows you to simultaneously connect
optional devices mentioned before as well as other
AV devices. For details, refer to the operating instructions for the Expansion Module.
Connectable devices
¡CD/DVD changer (max. 1)
¡iPod
®
(max. 2)
¡Hands-Free Phone System (max. 1)
¡TV tuner (max. 1)
Note:
¡Market conditions regarding optional devices vary
with countries and regions. For further information,
consult your dealer.
■ Integration of the monitor, FM/AM radio,
DVD Video/Video CD player and
CD/MP3/WMA player
■ Built-in AV Input/Output Terminals
For more convenient connection and setup, all terminals are now provided on the unit itself.
■ Built-in Dolby Digital decoder, DTS decoder
You can enjoy a powerful 5.1 channel surround system by connecting optional center speaker, power
amplifier and sub-woofer.
■ Built-in DSP
7 bands graphic equalizer. (apage 32)
■ GUI (Graphic User Interface)
GUI displays various indications with colorful symbols to enhance visibility, enjoyment, and operability.
■ Disc type and input signal auto-detection
The signal auto-detection function of this unit allows
users to be free from selection between PAL and
NTSC before use of your discs or devices. (For out-
put signal,
set . (apage 36)
)
TV TYPE
■ CS Auto (Circle Surround Automotive)
CS Auto allows your car interior to change to a
splendid audio room in a moment. Every speaker can
be fine-tuned. (apage 33)
is a trademark of SRS Labs, Inc.
CS Auto technology is incorporated under license
from SRS Labs, Inc.
Note:
¡
If you enable CS Auto, the following functions are
automatically disabled:
, , ,
(apage 32-37)
.
■ Touch Panel Operation
Simply touch the screen lightly to operate virtually all
functions. Easy-to-use menus and icons let you
“touch and choose” what you want, so you can start
using your system from the very first day. That also
means that while you drive, you can concentrate on
the road.
■ DVD–R, DVD–RW Playback
(apage 16, 48 for details)
■ ID code
4-digit ID code for increased security.
Fill in the ID code memo (a page 46).
CROSS OVER
MULTI-CHDOWN MIXGRAPHIC-EQ
Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully
selected components, and assembled by people who are proud of the reputation their work has built for our company.
We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability
we have built into it, you too will be proud to be a member of our family.
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are
connected.
■ No device is connected to this unit. a Basic operations are covered only by this book.
■ Optional devices are connected to this unit. a Refer to the “System Upgrade Guidebook” in addition.
7
CQ-VD7003W
Contents
¢ Safety Information .......................... 2
¢ Notes on use ................................................... 5
¢ Before Reading These Instructions .............. 5
¢ Components .................................................... 5
¢ Features ........................................................... 6
¢ Contents .......................................................... 7
¢ Preparation...................................... 8
Settings, remote control unit, symbols used in this
manual
¢ Name of Controls and Functions ................ 10
¢ Touch Panel Operation Oveview ................. 12
¢ General .......................................... 14
Power on/power off, display open/close, source
selection, volume, mute, tilt angle, folding down the
display
¢
Before Disc Playback
..................... 16
¢
Disc
Player..................................... 18
¢ Notes on MP3/WMA ...................................... 22
¢ Radio.............................................. 24
¢ AV1/AV2 ......................................... 26
¢ Settings ......................................... 28
Menu operation
User, screen, audio, DVD, input/output, radio
¢ Troubleshooting ........................... 41
¢ Maintenance .................................................. 47
¢ Notes on Discs .............................................. 48
¢ Language Code List...................................... 49
¢ Definition of Terms ....................................... 50
¢ Specifications................................................ 51
English 2
52
кЫТТНЛИ 102
7
8
CQ-VD7003W
English
Preparation
(user settings) ( apage 30)
display unit, clock, ID code, memory clear, other
(screen settings) (apage 32)
dimmer, picture
(audio settings) (apage 32)
sound setup, graphic equalizer, CS Auto, speaker setup,
speaker level, time alignment, source level, cross over
(DVD settings) (apage 36)
language, display, pro logic, down mix, dynamic range
compression, multiple channel
(AV-IN/OUT settings) (apage 37)
source skip
(radio settings) (apage 38)
FM set up, AM set up
Note:
¡
Refer to “Settings” (apage 28) for further information
about operations, settings, and others of the menu
screen.
RADIO
INPUT/OUTPUT
DVD
AUDIO
SCREEN
USER
You may need to set the following depending on the
devices to be connected.
Subwoofer
¡
Execute (speaker set up) and
(speaker level). (apage 34)
Other speakers
¡
Execute (speaker set up). (apage 34)
AV1/AV2 (Camcorder,VCR, etc.)
¡
Adjust (AV1/AV2 input level).
(apage 35)
SOURCE LEVEL
SP SETUP
SP LEVELSP SETUP
Settings
Warning
¡When you connect external devices to AV1-IN/
AV2-IN (AV1/AV2), be sure to connect the side
brake connection lead (aInstallation Instructions).
Please refer to the separate “System Upgrade
Guidebook” for how to operate this unit when optional devices are connected.
2
3
Lithium battery
(CR2025: supplied)
Battery case
Remote Control Unit
Warning
¡Keep batteries away from children to avoid the risk
of accidents. If an infant ingests a battery, please
seek immediate medical attention.
Caution
¡Remove and dispose of an old battery immediately.
¡Do not disassemble, heat or short a battery. Do not
throw a battery into a fire or water.
¡Follow local regulations when disposing of a battery.
¡Improper use of a battery may cause overheating, an
explosion or ignition, resulting in injury or a fire.
Note:
¡Battery Information:
Battery Type: Panasonic lithium battery (CR2025)
Battery Life: Approximately 6 months under normal
use (at room temperature)
Battery Replacement
q Remove the battery holder with the remote control
unit placed on a flat surface.
q Stick your thumbnail into the groove and push the
holder in the direction of the arrow at the same
time.
w Pull it out in the direction of the arrow using a
tough pointed object.
Before Initial Use
Pull the insulation film out from
the backside of the remote control gently.
w Put a battery in the case with (+)-side facing up.
e Put the case back.
Tough pointed object
8
9
CQ-VD7003W
English
Pictographs
You can perform some operations of this unit in one or
more methods with the touch panel or remote control.
This book explains such operations in tabular form as follows. Refer to the following for the pictographs located in
the upper part of each table.
Symbols used in this manual
Disc Marks
The following pictographs are used for the descriptions
of disc operation. (a page 17-21)
: DVD
: VCD (Video CD)
: CD
: CD-R/RWs containing MP3 files
: CD-R/RWs containing WMA files
WMA
WMA
WMA
MP3
MP3
MP3
CDCDCD
VCD
VCD
VCD
DVD
DVD
DVD
Compatible types of disc
The discs compatible with the targeted operation.
Compatible
Discs
Compatible
Discs
Operation on the Touch Panel
You can use the touch panel to perform the targeted
operation. If the operation is not executable with the
touch panel, “––” is displayed.
Operation on the Remote Control Unit
You can use the remote control to perform the targeted
operation. If the operation is not executable with the
remote control, “––” is displayed.
Operation on the Unit
You can use the Unit to perform the targeted operation. If
the operation is not executable with the Unit, “––” is displayed.
9
10
CQ-VD7003W
English
Name of Controls and Functions
ENTER
TILT O/C
ASP
MUTE
SRC MENU
CQ-VD7001U
NAVI
OPEN / CLOSE
ASPECT
PWR
VOL
P·MODE
CLOSE
CQ-VD7003W
TILT
TEXT
ENTER
TILT OPEN
ASP
MUTE
SRC MENU
CQ-VD7003W
NAVI
CLOSE
ASPECT
PWR
VOL
P·MODE
Main Unit
Main Unit
Disc slot Remote control
sensor
w [VOL]
e [MUTE]
r [SRC] (PWR)
(SOURCE/POWER)
(Display Closed)
(Display Raised)
t [MENU]
y [NAVI]
Dimmer Sensor
(
a
page 32)
DIMMER
!0 [TILT]
o [OPEN] (CLOSE)
o [OPEN] (CLOSE)
!0 [TILT]
u [u]
q [ASP] (ASPECT)
(P•MODE (PRIVATE
MODE))
q [ASP] (ASPECT)
(P•MODE)
q
w
[
VOL
]
e
[
MUTE
]
r
t
[
MENU
]
y
u[u
]
i
[
ENTER
]
o
!0
[
TILT
]
¡Adjusts the monitor position.
¡Tilts the monitor forward temporarily.
¡Opens/closes the monitor.
[
OPEN
]
(CLOSE)
¡Selects a band.
¡Shows OSD.
¡Searches for broadcast stations and
memorizes them automatically.
¡Determines an operation or item.
¡Selects or searches for a track, file, sta-
tion.
¡Selects or searches for a channel.
¡Selects (horizontally) or adjusts an opera-
tion or item.
[]] [[]
(TUNE/TRACK)
¡Selects a folder or a disc.
¡Selects (vertically) or adjusts an operation
or item.
[}] [{]
(DISC)
¡Ejects/reloads a disc.
Note:
¡A disc is in the slot when this is illuminat-
ed in blue.
¡Switches navigation mode on and off.
(available in the future)
[
NAVI
]
¡Shows the menu screen.
¡Switches on/off the power.
¡Changes the modes such as sound and
picture.
[SRC]
(PWR)
¡Mutes the sound temporarily.
¡Adjusts the sound volume.
¡Selects the aspect ratio.
¡Activates/inactivates the private mode.
[ASP]
(ASPECT)
(P•MODE)
: This book refers to connections to the Panasonic car navigation system that will come onto the market in the future. Descriptions
regarding the car navigation system are boxed with a dotted line.
i
[ENTER]
[] ][[ ]
(TUNE/TRACK)
[}] [{]
(DISC)
Note:
¡
[ASP], [MENU], [u], [OPEN], [TILT] are available only on the display unit.
10
11
CQ-VD7003W
English
CAR AV
MUTE
ENT
VOL
SRC
PWR
DVD MENU
RET
RETURN
TOP MENU
ENTER / BAND
r
[
MUTE
]
t
[+] [–]
(VOL)
q [SRC] (PWR)
(SOURCE/POWER)
e
[RET]
(RETURN)
u
[]
(TOP MENU/DVD MENU)
w
[■][❚❚][B]
[s] [d]
Aim the remote control at the remote control sensor of the display unit and operate it.
y
[}] [{]
[]] [[]
[
ENT
] (ENTER/BAND)
Remote Control
q
w
[■]
[❚❚]
[B]
e
r
t
y
u
¡Displays the DVD/title menu. (Operations
vary according to the media.)
[ ]
(TOP MENU/
DVD MENU)
¡Selects a band.
¡Shows OSD.
¡Searches for broadcast stations and
memorizes them automatically.
¡Determines an operation or item.
[ENT]
(ENTER/
BAND)
¡Selects (vertically) or adjusts an operation
or item.
[}] [{]
¡Selects or searches for a track, file, sta-
tion.
¡Selects (horizontally) or adjusts an opera-
tion or item.
[]] [[]
¡Adjusts the sound volume.
[+] [–]
(VOL)
¡Mutes the sound temporarily.
[
MUTE
]
¡Returns to the previous display.
¡Inputs the number again.
¡Displays the VCD’s menu.
[RET]
(RETURN)
¡Goes to beginning.
¡Fast forward/fast reverse.
¡Slow playback ([d]).
[s] [d]
¡Playback
¡Pause
¡Stops playback.
¡Switches the power on/off.
¡Changes the modes such as sound and
picture.
[SRC]
(PWR)
Note:
¡
[ENT], [RET],
[■], [❚❚], [B],
[]
are available only on the remote control unit.
11
12
CQ-VD7003W
English
Touch Panel Operation Overview
The State of Operation Screen
❒ Notes on the Touch Panel
Before operation
¡Clean the surface of the touch panel. (a page 47)
Operation
¡Use only your fingers to operate the touch panel.
¡Do not press the panel forcefully.
¡Do not scratch the panel with fingernails or any
hard objects.
¡Do not use a pen or other sharp implements to
operate the touch panel.
¡Do not bump the front panel.
a Failure to observe the above may damage or
break the glass on the surface of the touch
panel.
Prohibition
Input is not possible because the user has
attempted to perform an operation which
is not supported by the disc contents.
Displays the Source Selection Screen.
Source Button Menu Button
Example: DVD mode
Displays the Menu Screen.
Display Button
(a next page)
Volume
indicator
Current
mode
Disc indicator (a page 17)
(Lights when a disc is loaded)
Clock time (a page 30)
Note
:
¡The following picture is partly darkened for explanation.
¡Displaying contents and their positions partly vary with each mode. Refer to the description of each mode for details.
(Content varies with each
source)
Source Selection Screen appears.
Touch desired source button.
Touch to quit.
Note
:
¡The screen above appears when no external
device is connected to AV1, AV2, and the
Expansion Module (CY-EM100N, option).
Source Selection Screen Menu Screen
Menu Screen appears. Select desired setting.
Menu Setting, (a page 28)
Press [SRC] to change to
desired mode.
Press [MENU] to let Menu
Screen appear.
12
13
CQ-VD7003W
English
Radio
(a page 24)
*1To switch Operation Screen ON, touch the center of touch panel or press [ENTER].
*
2
The operation screen is not available in the video mode.
DVD mode
Showing the hidden part of the screen.
Some items have continued parts. You can see the continued parts by pressing or .
Note:
¡
Refer to the description of each mode for how to operate the operation screen.
Switching the Display
Disc Player (DVD/VCD(*1)/
CD/MP3/WMA)
(a page 18)
Touching allows users to switch between screens as follows.
Standard Screen Operation Screen
AV1/AV2 (*
1)
(a page 26)
Source
Standard Screen OSD OFF *
2
Source
Please refer to the separate “System Upgrade Guidebook” for how to operate this unit when optional devices are
connected.
❏ How to Call up Operation Screen
❏ How to Cancel OSD (On Screen Display)
13
14
CQ-VD7003W
English
Operations
General
ENTER
TILT OPEN
ASP
MUTE
SRC MENU
CQ-VD7003W
NAVI
CLOSE
ASPECT
PWR
VOL
P·MODE
TILT OPEN
ENTER
MUTE
SRC
[MUTE]
[OPEN]
(CLOSE)
[SRC] (PWR: power)
[TILT]
[VOL]
Remote Control Sensor
[SRC]
–
–
–
[SRC]
[SRC]
(a page 12)
[SRC]
General Operations
Power
ON :
Source selection
[OPEN]
¡Press once to open. Press again to close.
Display Open/Close
Note:
¡When the display unit is opened or closed, a loud beep sounds three times.
¡If the unit stops halfway, press [OPEN] again to draw it all the way out.
¡Opening/closing the display can be done when the power is off.
–
[SRC]
[SRC]
Power
OFF :
Preparation: Turn your car’s ignition key to the ACC or ON position.
……
Touch/Press and hold for more than 2 seconds
RADIO (AM/FM)
(a page 24)
(a page 18)
(a page 26)
(a System Upgrade
Guidebook)
AV1/AV2
Sources connected to the
Expansion Module (CY-EM100N) *
1
DVD (DVD/VCD (Video CD)/CD/MP3/WMA)
*1 When the Expansion Module (CY-EM100N, option) is connected.
(a System Upgrade Guidebook)
Note:
¡
If there is no external sources connected, AV1/AV2 mode can be set
to skip. (a page 37)
Note:
¡
You cannot turn on the power via the
remote control when is set to
. (
a
, page 31)
ACC SELECTOFF
ACC SELECT
[] ][[ ]
14
15
CQ-VD7003W
English
CAR AV
MUTE
ENT
VOL
SRC
PWR
DVD MENU
RET
RETURN
TOP MENU
ENTER / BAND
MUTE
SRC
MUTE
SRC
VOL
[SRC] (PWR: power)
[MUTE]
[] ] [[]
[+] [–
]
(VOL)
q Press and hold for more than 2 sec-
onds.
w
Press to adjust. Setup is the same as
from MENU. Refer to
for details. (apage 30)
DISPLAY UNIT
Operations
–
or
––
[]] or [[]
–
–
–
q [+]
w [
–]
q Up
w Down
wq
Volume
Note:
¡The sound level for
each source is
stored in memory.
[TILT]
[]] or [[]
To raise the display, press again.
Tilt Angle
Folding Down the
Display
Temporarily
[TILT]
Mutes the sound.
To cancel, press again.
[MUTE] [MUTE]
Mute
Note:
¡
Vertical angle (TILT) is saved in the memory, so when the display unit is drawn out
next, it is automatically set at the angle and in the position adjusted before.
¡After adjusting its angle, also adjust the brightness as well. (a page 32)
¡The car model and installation conditions may impose some restrictions on the
adjustment of the monitor's angle.
Note:
¡Even when the unit power is off, you can fold down the display te
mporarily.
Setting Range: – 82 dB to 0 dB, default:
– 40 dB
Note:
¡ The volume level can be set independently for each source and each
disc format.
Caution
¡Avoid physical shock to the monitor.
¡Do not place any object on the display unit, or subject it to undue force.
¡Do not move the display forcibly.
¡The monitor movable range may be limited by the type of car, the position where
the display is mounted, etc.
Warning
¡Do not touch the unit while the display is moving. Inserting hands, fingers or for-
eign objects into the unit can cause injuries and damage to the unit.
General Operations (continued)
15
16
CQ-VD7003W
English
Before Disc Playback
Discs that can be Played Back
❒ Symbols used on jackets
(Examples of such symbols include)
¡ : Number of subtitle languages
¡ : Number of audio tracks
¡ : Number of angles
The numbers indicate the number of languages,
tracks, angles, etc., recorded on the disc.
Screen size (H:V aspect ratio)
¡ : 4:3 standard size
¡ : Letterbox (a page 36)
¡ 16:9 wide size
: Playback in format on a
standard screen (4:3).
: Playback in (a page 36)
format on a standard screen (4:3).
Note:
¡
The size of the image that is displayed on the screen
depends on the screen mode (“Aspect Ratio”
a
page
39), and on the screen size for the content on the
disc.
❒ Region Management Information
This product is designed and manufactured to
respond to the Region Management Information that
is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to
the Region number of this product, this product does
not play the disc.
PAN & SCAN
PS16:9
LETTERBOX
LB16:9
LB
4:3
3
2
2
The Region number for
this product is “2”
(*1)
,
“3”
(*2)
, “4”
(*3)
, “5”
(*4)
and “ALL”.
*1 CQ-VD7003W2
*
2
CQ-VD7003W3
*
3
CQ-VD7003W4
*
4
CQ-VD7003W5
❒ Disc Type
Example:
TEXT
Recordable
ReWritable
DISC DVD
VCD
(Video CD)
CD CD-R/RW
Mark/logo
Disc Size 12 cm
Video
Format
NTSC/PAL
Audio
Format
LPCM,
MPEG1,
MPEG2,
dts, Dolby
Digital
LPCM,
MPEG1
LPCM
(CD-DA),
dts
LPCM
(CD-DA),
MP3/
WMA
Region
No.
2
(*1)
, 3
(*2)
,
4
(*3)
, 5
(*4)
,
(ALL)
❒ Notes on DVD–Rs/RWs
¡Only video formatted discs are playable. Discs in the
video recording (VR) format are unplayable.
¡Unfinalized discs are unplayable.
¡Some discs are unplayable depending on the disc
itself, device, drive and software that are used for disc
recording.
❒ Discs not supported
The following discs are not played back on this
product.
¡DVD-Audio ¡DVD-ROM ¡DVD-RAM
¡DVD+R ¡DVD+RW
¡SVCD ¡VSD ¡CVD
¡CD-G ¡CD-ROM (except MP3/WMA)
¡CD-RW (except MP3/WMA and CD-DA)
¡CD-R (except MP3/WMA and CD-DA)
¡SACD ¡Photo CD ¡CDV
¡Hybrid SACD (except CD-DA)
¡Divx Video Discs
¡CD-EXTRA (audio-only playback possible)
¡DVDs with a region number other than “2”
(*1)
,
“3”
(*2)
, “4”
(*3)
, “5”
(*4)
or “ALL”
*1 CQ-VD7003W2 *2 CQ-VD7003W3 *3 CQ-VD7003W4
*
4
CQ-VD7003W5
¡Playing back a photo CD disc with this unit could
damage the data that is recorded on the disc.
*1 CQ-VD7003W2 *2 CQ-VD7003W3 *3 CQ-VD7003W4
*
4
CQ-VD7003W5
Note:
¡About CD-Rs/RWs and DVD–Rs/RWs, refer to “Notes on
CD-Rs/RWs and DVD–Rs/RWs”. (a page 48)
¡Some copy-protected music CDs are not playable.
2
(*1)
3
(*2)
4
(*3)
ALL
5
(*4)
Loading...