Panasonic AG-HVX200 User Manual

Operating Instructions

Memory Card Camera-Recorder

Before use

of parts

Model No.

P AG-

Before operating this product, please read the instructions carefully and save this manual for future use.

F1205S3046-H Printed in Japan

ENGLISH

VQT0S52-3

Reference Menu Displays Editing Playback Shooting Preparation Description

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER TO SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

• TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

•

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS. USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT.

CAUTION:

TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES O N LY.

CAUTION:

THE AC RECEPTACLE (MAINS SOCKET OUTLET) SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE POWER CORD PLUG FROM THE AC RECEPTACLE.

CAUTION:

Danger of explosion or fire if battery is mistreated.

For Battery Pack

• Replace only with same or specified type.

• Do not disassemble or dispose of in fire.

•

Do not store in temperatures over 60°C (140°F).

• Use specified charger.

For Battery of Remote Controller

• Replace battery with part No. CR2025 only.

• Do not recharge the battery.

• Do not disassemble or dispose of in fire.

•

Do not store in temperatures over 60°C (140°F).

Camera-Recorder

The rating plate is on the underside of the viewfinder.

AC Adapter

The rating plate is on the underside of the AC Adapter. Disconnect the AC mains plug from the AC mains socket when not in use.

CAUTION:

In order to maintain adequate ventilation, do not install or place this unit in a bookcase, built-in cabinet or any other confined space. To prevent risk of electric shock or fire hazard due to overheating, ensure that curtains and any other materials do not obstruct the ventilation.

indicates safety information.

IMPORTANT

“Unauthorized recording of copyrighted television programs, video tapes and other materials may infringe the right of copyright owners and be contrary to copyright laws.”

FCC NOTICE (USA)

Declaration of Conformity

Model Number: AG-HVX200P Trade Name: PANASONIC Responsible Party: Panasonic Corporation of North America One Panasonic Way, Secaucus, NJ

Support contact: Panasonic Broadcast & Television Systems Company 1-800-524-1448 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To assure continued compliance, follow the attached installation instructions and do not make any unauthorized modifications.

07094

CAUTION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The user may find the booklet “Something About Interference” available from FCC local regional offices helpful.

FCC Warning:

To assure continued FCC emission limit compliance, the user must use only shielded interface cables when connecting to host computer or peripheral devices. Also, any unauthorized changes or modifications to this equipment could void the user’s authority to operate this device.

NOTIFICATION (Canada)

This class B digital apparatus complies with Canadian ICES-003. Cet appareil numéique de la classe B est conforme à la norme NMB-003 du Canada.

indicates safety information.

A lithium ion/polymer battery that is recyclable powers the product you have purchased. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Software information for this product

1. Customer advisory: This product includes software licensed under the GNU General Public License (GPL) and GNU Lesser General Public License (LGPL); customers have the right to download, modify, and redistribute source code for this software.

Descriptions of the GPL and LGPL are stored on the installation CD included with this camera-recorder. See the folder named \LDOC. (The description is the original (written in English).) To download the

relevant source code, visit https://eww.pavc.panasonic.co.jp/pro-av/

Please note that we cannot answer any questions you may have about the content, etc. of any source

code you may obtain from the above Web site.

2. This product includes software licensed under the MIT License. A description of the MIT is stored on the installation CD included with this camera-recorder. See the folder named \LDOC. (The description is the original (written in English).)

• LEICA is a trademark of Leica Microsystems IRGmbH.

• DICOMAR is a trademark of Leica Camera AG.

• SD logo is a trademark.

All other explanations, company names, and product names are the registered trademarks of the respective companies.

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Before use

Software information for this product ..........4

IMPORTANT SAFETY INSTRUCTIONS .........5

Outline of operations .....................................8

Read this first! ..............................................10

Accessories .................................................. 11

About this manual ........................................ 11

Description of parts

Description of parts ..................................... 12

Right side and rear side .................................. 12

Left side ...........................................................13

Terminals and mounting parts .........................14

Remote control ................................................ 15

Preparation

The battery .................................................... 16

Charging .......................................................... 16

Installing and removing

the power supply ..................................17

Installing and removing the battery ................. 17

Connecting and disconnecting the power cord

... 17

Adjusting the hand strap ............................. 18

Attaching the shoulder strap ....................... 18

Detaching and attaching the lens hood .....18

The remote control .......................................19

Insert the battery ............................................. 19

Remote control setup ......................................19

Turn on/off the camera .................................20

Tally lamp ......................................................20

Viewfinder .....................................................21

Using the viewfinder ........................................ 21

Using the LCD ................................................. 22

Emphasizing outlines ...................................... 22

Adjusting the screen display ............................ 23

Setting the calendar ..................................... 24

Shooting

Basic shooting operations (P2 card) ..........25

Preparing to shoot using a P2 card ................. 25

Shooting in auto mode .................................... 25

Checking photos taken (REC CHECK) ...........26

P2 card access lamps .....................................26

Protecting against a possible erasure .............26

Formatting P2 cards ........................................ 27

Recording times .............................................. 27

Remove the P2 card ........................................ 28

Basic shooting operations

(Cassette tape) ...................................... 29

Preparing to shoot using a tape ...................... 29

Shooting in auto mode .................................... 29

Checking scenes taken (REC CHECK) ........... 30

Remove the cassette tape ............................... 30

Cassette tapes ................................................ 31

Using SD memory cards .............................. 32

Installing and removing the SD memory card . 32

Formatting SD memory card ...........................32

Cautions in using SD memory cards ............... 32

Using the zoom function .............................. 33

Variable frame rates (VFR) ........................... 34

Native recording ..............................................35

Standard recording .......................................... 35

Using variable frame rates (VFR) .................... 36

Shooting in 1080i/480i progressive mode .. 37

Shooting in manual mode ............................ 38

Switching to manual mode .............................38

Manual focusing .............................................38

Using focus assist ............................................ 38

Iris adjustments ...............................................39

Adjusting the gain ............................................ 39

Light intensity adjustments .............................. 39

Adjusting the white balance ............................. 40

Shooting techniques for different targets .. 42

Low-angle shooting .........................................42

Self-portrait shooting ......................................42

Zebra pattern .................................................. 43

Marker ............................................................. 43

Checking and displaying shooting status ........44

Changing the image size ................................. 44

Optical Image Stabilizer .................................. 45

Adding effects to images ................................. 45

Using the USER buttons ................................. 45

Backlight compensation ................................... 45

Color bars ........................................................ 45

Adjusting the volume while shooting ...............46

Backup recording ............................................ 46

Pre-recording (PRE REC) ...............................47

Interval recording (INTERVAL REC) ................ 47

One-shot recording (ONE-SHOT REC) ........... 47

Loop recording (LOOP REC) .......................... 48

2-slot continuous recording .............................48

Shot mark function .......................................... 48

Text memo recording ....................................... 48

Finding specific scenes(image search) ...........49

Index recording ................................................ 49

Adjusting the shutter speed ........................ 50

Synchro scan ................................................... 51

Switching Audio Input .................................. 52

Using the built-in microphone .......................... 52

Using another microphone

and audio equipment ................................... 52

Adjusting the recording level ...........................53

Using scene files .......................................... 54

Changing scene file settings ........................... 54

Saving scene files and other settings

on SD memory cards ............................ 56

Clip metadata ................................................ 57

Using the Counter ........................................58

Counter display (P2 card / Tape) .....................58

Memory stop mode (Tape) .............................. 58

1394TC preset mode ...................................... 58

Charging the built-in battery/

Setting the time data ............................ 59

Recharging the built-in battery ........................ 59

Setting the time code ....................................... 59

Specifying the time code (TC PRESET) .......... 59

Setting user information .................................. 60

Playback

Basic playback operations (P2 card) .......... 62

Basic playback operations (Tape) ............... 63

Thumbnail screen ......................................... 64

Basic thumbnail screen operations ................. 64

Adding shot marks to clips .............................. 66

Clearing the thumbnail screen ......................... 66

Direct shooting functions ................................. 66

Thumbnail operations .................................. 67

Selecting the thumbnail display method

(THUMBNAIL) ............................................. 67

Deleting clips and formatting cards

(OPERATION) ............................................. 69

Checking the clip or card information

(PROPERTY) ..............................................70

Uploading the metadata (META DATA) ............ 72

Useful playback functions ........................... 73

Variable speed search (P2 card / Tape) ........... 73

Slow playback (P2 card / Tape) .......................73

Fast forward/rewind playback (P2 card) ..........73

Fast forward/rewind playback (Tape) ...............73

Frame-by-frame playback (P2 card / Tape) ...... 74

Clip skip (P2 card) ........................................... 74

End search (Tape) ........................................... 74

Index search (Tape) ......................................... 75

Adjusting the volume (P2 card / Tape) ............. 75

Viewing images on a television

(P2 card / Tape) ...........................................75

Checking the date and time (P2 card / Tape) .. 75

Editing

Connecting external units ...........................76

Headphones .................................................... 76

External microphone ....................................... 76

Computer (non-linear editing/file transfer) ....... 77

Hard disk drive (data copying) ......................... 77

Digital video equipment (Dubbing) ..................78

Video deck (Dubbing) ...................................... 79

TV/Monitor (playback/dubbing) ........................ 79

Audio dubbing .............................................. 80

Nonlinear editing with P2 card

(PC mode) .............................................. 82

Copying from P2 cards to the hard disk drive

(1394 HOST mode) ................................ 84

Warnings ......................................................... 85

Dubbing ......................................................... 86

Dubbing the contents of P2 cards onto a tape

(dubbing mode) ........................................... 86

Digital input/output (P2 card/Tape) .................. 87

Analog output (P2 card/Tape) .......................... 88

Analog input (Tape) .........................................89

Displays

Screen displays ............................................ 90

Regular displays .............................................. 90

Warnings ......................................................... 93

Setting the DISPLAY items .............................. 95

Menus

Using the setup menus ................................ 96

Using the menus ............................................ 96

Initializing the menu settings ..........................97

Setup menu structure ..................................98

Camera mode menu ........................................ 98

MCR/VCR (playback and external input)

mode menu .................................................99

Dubbing mode menu ....................................... 99

Setup menu list ........................................... 100

SCENE FILE screen ...................................... 100

CAMERA SETUP screen ..............................102

SW MODE screen ......................................... 103

AUTO SW screen ..........................................105

RECORDING SETUP screen ........................ 106

PLAYBACK FUNCTIONS screen .................. 109

DUBBING SETUP screen .............................111

AV IN/OUT SETUP screen ............................ 111

DISPLAY SETUP screen ............................... 112

CARD FUNCTIONS screen .......................... 114

OTHER FUNCTIONS screen ........................ 114

OPTION MENU ............................................. 118

Reference

Before calling for service ........................... 119

Operating precautions ............................... 123

Updating the driver in the camera ............125

Condensation .............................................. 125

System resetting ......................................... 126

Cleaning ...................................................... 126

Video Heads ................................................ 127

Storage Precautions ................................... 128

Recording format ........................................ 129

Appendix ..................................................... 130

Specifications ............................................. 131

Before use

Outline of operations

This unit is compatible with P2 (Professional Plug-in) cards or DV cassette tapes. The P2 card has a large capacity with a high transfer rate, and allows you sophisticated movie-making on this handy camera, including HD (High Definition) recording and smooth editing/dubbing.

Flow of shooting, playing and saving

The setting values such as the user file are saved to and read from the SD memory card.

P2 mode shooting and playback

(Pages 25 and 73)

P2 card

You can use the following features:

• HD (High Definition) recording

• Multi format recording

• Variable frame rates Slow & quick motion recording

• Maximum 4 channel uncompressed digital audio recording

• DV recording (480i)

Dubbing mode (Page 86)

Dubbing mode is a function for down-converting contents recorded in HD (1080i, 720P) on the P2 card to an DV format (480i) and recording it to tape. You can record onto DV tape contents that have a slow & quick motion effect. This is useful when backing up images and checking images on AV equipment.

Cassette tape shooting and

playback (Pages 29 and 73)

DV cassette tape

• DV recording (480i)

• Dubbing mode recording from a P2 card is possible.

• You cannot simultaneously shoot on both the P2 card and the DV cassette tape.

• High-definition (HD) recording to a DV tape is not possible.

Saving and editing on external devices

P2 card

USB2.0 (Windows) IEEE1394 (Macintosh)

PC mode (Page 82)

The data (file) is transferred for nonlinear editing on your computer or other unit.

Computer

1394 host mode (Page 84)

The unit directly controls the external hard disk drive, and transfers the data (file) to it.

External hard disk

Before use

DV cassette tape

AV cable

Component video cable

IEEE1394 (SBP-2∗)

IEEE1394 (Windows/Macintosh)

Video equipment

/Television

Computer

Memory card recorder

The contents can be transferred as a data stream (digital dubbing).

∗

Serial Bus Protocol-2

Read this first!

Always take some trial shots before actual shooting.

• When shooting important events (such as weddings), always take some trial shots and check that the sound and images have been recorded properly before actual shooting.

Be sure to check and set the calendar and time zone.

• These settings affect the control and playback sequence of the recorded contents. Before making a recording, set and check the calendar and time zone. (Page 24)

Panasonic makes no guarantees for your recordings.

• Please understand that Panasonic makes no guarantees for your recordings in cases where images and/ or sound were not recorded as you intended due to problems with the camera-recorder or cassette.

Respect copyrights

• Copyright laws forbid the use of video and audio material you have recorded for any purpose other than your own personal enjoyment. Remember that restrictions apply to the shooting of certain material even if it is intended for private use.

Caution regarding laser beams

• The CCD may be damaged if it is subjected to light from a laser beam.

When using the camera-recorder in locations where laser irradiation equipment is used, be careful not to

allow the laser beam to shine directly on the lens.

Notes when connecting a DV (IEEE1394) cable

• Windows:

Before connecting, turn off the main unit power, and check the shape and orientation of the terminal.

• Macintosh:

After turning on the power of the Apple Macintosh computer, check the shape and orientation of the

terminal, and then connect the cable.

(Pages 77, 78)

Media that can be used in this unit

The following media can be used in this unit. For details, refer to the respective pages.

• P2 card (Page 27)

• Digital video cassette tape (Page 29)

• SD memory card (Page 32)

Mounting the camera-recorder on a tripod

The tripod mounting hole is 5.5 mm deep. Do not force the tripod screw beyond this depth. You can damage the camera-recorder if you use any screw other than 1/4-20UNC.

For other usage notes, see page 123.

Attach the tripod to the tripod hole.

Accessories

∗

Battery

AC Adapter AC power supply cord

/DC cord

Wireless remote control and button battery (CR2025)

Before use

Microphone holderEye cup

Shoulder belt Component

video cable

Documents and CD

A lens hood cap (page 18) and INPUT 1/2 terminal (page 14) cover are attached to the camera-recorder.

∗1 For part numbers for the battery, see “OPTIONAL UNITS”. (Page 133) ∗2 When using 1394 cable (sold separately), install a ferrite core on the end nearest the PC. (Page 78)

6-mm screws (2) 12-mm screws (2)

PIN-BNC conversion plugs (3)

Microphone holder adapter

Ferrite core

∗

About this manual

Note concerning illustrations in these instructions

• Illustrations (camera-recorder, menu screens, etc.) in these operating instructions differ slightly from the actual camera-recorder.

References

• References are shown as (Page 10).

Icons

Explanations specific to the media used are identified by the icons below.

: Explanations for P2 card usage only.

TAP E

: Explanations for tape usage only.

Description of parts

Right side and rear side

357

13 14

1 POWER switch (Page 20)

2 START/STOP button (Pages 25 and 29)

3 OPEN/EJECT switch (Page 29)

4 REC CHECK button (Pages 25 and 30)

5 HANDLE ZOOM switch (Page 33)

6 Zoom button (Page 33)

7 Handle zoom button (Page 33)

8 Handle START/STOP button

(Pages 25 and 29)

9 Pin hole (for zoom ring) (Page 13)

10 Built-in stereo microphone (Page 52)

11 Tally lamp (Front) (Page 20)

12 Remote control sensor (Front)

13 Cassette holder (Pages 29 and 30)

14 Cassette cover (Pages 29 and 30)

15 White balance sensor (Page 40)

16 INPUT 1/2 (audio input) switch (Page 52)

17 Lens hood screw (Page 18)

18 P2 card access lamp (x 2) (Page 26)

19 Viewfinder (Page 21)

20 P2 card slot (x 2) (Page 25)

21 SCENE FILE dial (Page 54)

22 Mode button (Page 25 and 29)

23 Mode lamp (Page 25 and 29)

10 12

22 24 26 28 31

21 23 25 27 29

24 Remote control sensor (Rear)

25 Tally lamp (Rear) (Page 20)

26 MEDIA (P2/TAPE) switch

(Pages 25 and 29)

27 EVF DTL button (Page 22)

28 Power terminal (Page 17)

29 AUDIO control (Page 53)

30 DC INPUT terminal (7.9 V)

31 Battery release button (Page 17)

2 1

3015 17

Left side

AWB

ZOOM

SERVO

MANUAL

324

10 12 14 16

13 15

1 Focus ring (Page 38)

2 Zoom ring (Page 33)

If you don’t need the zoom ring pin, fit it into the provided pin hole (Page 12) so that you don’t lose it.

3 FOCUS ASSIST button (Page 38)

4 Built-in speaker (Page 75)

5 ZOOM switch (Page 33)

6 AWB button (Page 40)

7 FOCUS switch (Page 38)

8 PUSH AUTO button (Page 38)

9 IRIS dial (Page 39)

10 ND FILTER switch (Page 39)

11 IRIS button (Page 39)

12 GAIN switch (Page 39)

13 WHITE BAL switch (Page 40)

14 DISP/MODE CHK button (Page 44)

15 USER button (Page 45)

16 AUTO/MANUAL switch (Pages 25 and 29)

17 LCD monitor (Page 22)

18 Diopter adjustment dial (Page 21)

19 AUDIO DUB/THUMBNAIL button

(Pages 66 and 80)

20 MENU button (Page 96)

REC

AUDIO MON/VAR

SHUTTER

INT(R)

INPUT 2ONOFF

AUDIO

END SEARCH

SET

PAGE/

SPEED SEL

INPUT 1 INPUT 2

MIC POWER +48V

ZEBRA OIS

OFF

AUDIO DUB/ THUMBNAIL

20 21

25 26 27

BARS

RESET

CH 1 SELECT CH 2 SELECT

INT(L) INPUT 1 INPUT 2

COUNTER RESET/TC SET

28 29 30 31 32

21 PAGE/AUDIO MON/VAR button

(Pages 46 and 73)

22 REC button (Page 87)

23 END SEARCH button (Page 74)

24 Operation button (Page 96)

25 BARS button (Page 45)

26 CH1, CH2 SELECT switch (Page 52)

27 SHUTTER, SPEED SEL+/- button (Page 50)

28 RESET button (Page 126)

29 COUNTER - RESET/TC SET button (Page 58)

30 ZEBRA button (Page 43)

31 OIS button (Page 45)

32 INPUT1, 2 switch (MIC POWER +48 V)

(Page 52)

of parts

Description

Description of parts (continued)

Terminals and mounting parts

USB 2.0

1394

CAM REMOTE

ZOOM SS

FOCUS IRIS

1 Light shoe

2 Microphone shoe (Page 76)

3 USB terminal (Mini-B) (Pages 77 and 82)

4 Headphone jack (3.5 mm stereo mini jack)

(Page 76)

5 1394 terminal (Page 77)

6 SD memory card slot (Pages 32 and 56)

7 CAM REMOTE jack

∗

FOCUS/IRIS (3.5 mm mini jack)

You can connect a remote control unit to control the FOCUS and IRIS (aperture).

ZOOM S/S (2.5 mm super mini jack)

You can connect a remote control unit to control zoom and start/stop of recording.

8 Tripod hole (Page 10)

9 AUDIO IN/OUT CH1/CH2 terminal (Page 79)

10 VIDEO IN/OUT terminal (Page 79)

11 INPUT 1/2 terminal (XLR, 3 pin)

(Pages 52 and 80)

12 S-VIDEO IN/OUT terminal (Page 79)

13 COMPONENT OUT terminal (Page 79)

CH1

IN/

AUDIO

OUT

CH2

IN/

OUT

VIDEO

S-VIDEO

IN/OUT

COMPONENT

OUT

∗ Do not connect any equipment except the remote

controller to the remote control jack. Connecting any equipment other than the remote control may cause the image brightness to change and/or the images to appear out of focus.

Remote control

The following buttons are for functions that cannot be executed on the camera-recorder.

• PHOTO SHOT

• MULTI/P-IN-P

• STORE

• PB. ZOOM

OSD

COUNTER

MU L TI /

P-IN-P

STILL A D V

INDEX

SELECT

S T OR E

OFF/ON

P . B .DIGI T A L

• TITLE

• SELECT

• OFF/ON

P H O T O

SH O T

STILL A D V

S T A R T /

V O L +

ITEM

D A TE /

TIME

RESET TITLE

REC A.DUB

PL A Y /REW FF/

P A US E

S T O P INDEX

V AR .

S T O P

ZOOM

P B .

ZOOM

SET

1 DATE/TIME button (Page 75)

2 OSD button (Page 75)

3 COUNTER button (Page 58)

Same function as the COUNTER button on the main unit.

4 COUNTER RESET button (Page 58)

Same function as the COUNTER RESET button on the main unit.

5 A.DUB button (Page 80)

Same function as the AUDIO DUB button on the main unit.

6 REC button (Page 87)

Used during VCR mode

7 PLAY button (

/REW button ( ) (Page 62)

9 PAUSE button (

) (Page 62)

Like the operation buttons of the camera, MENU operations are performed using SET button.

10 STILL ADV button (

11 INDEX buttons (

12 STOP button (

13 FF/

button ( ) (Page 62)

, ) (Page 73)

, ) (Page 75)

) (Page 62)

Buttons for shooting and volume control

14 START/STOP button

Same function as the START/STOP button on the main unit.

15 ZOOM/VOL buttons (Pages 33 and 75)

of parts

Description

16 VAR. SEARCH button (Page 73)

17 MENU button

Functions the same as the MENU button on the camera.

[

], [ ], [ ], [ ] buttons

Function the same as the

, , , buttons

on the camera.

The battery

Charging

Before using the battery, fully charge it with the AC adapter. Keep a spare battery with you.

1 Align the battery with the “ ” marking on

the AC adapter, place it flat, and slide it in the direction shown below.

• You cannot charge the battery if the DC cord is connected to the DC OUT connector, so disconnect it first.

2 Plug the AC cord into the power outlet.

• The POWER lamp and CHARGE lamp on the AC adapter light, and charging begins.

• If the CHARGE lamp does not light when attached, detach the battery and then attach it again.

POWER

CHARGE

3 When the battery is charged, the CHARGE

lamp on the AC adapter goes out.

4 Slide the battery and remove it.

Recording time of included battery

Recharging time Continuous recording time

Approx. 330 min. Approx. 140 min.

• The times given above are approximate for when scenes are shot in the DVCPRO HD mode on a P2 card while using the viewfinder.

• The times apply when the ambient operating temperature is 68°F (20°C) and humidity is 60%.

Charging may take longer at other temperatures

and humidity levels.

• Keep metal objects (such as necklaces and hairpins) away from the battery. Shortcircuiting may occur across the terminals, causing the battery to heat up, and you may seriously burn yourself if you touch the battery in this state.

• The battery becomes hot while it is being used or charged. The camera-recorder itself also becomes hot during use.

• The recordable time reduces if you repeatedly start and stop recording.

• Discharge the battery before storing it. When storing it for an extended time, charge it at least once a year, use up its charge in the camerarecorder, and then store it again.

• If the battery is extremely hot or cold, the CHARGE lamp will blink several times before charging starts.

• If the CHARGE lamp continues to blink even when the battery temperature is normal, there may be something wrong with the battery or AC adapter. Contact your dealer.

• The battery takes longer to charge when it is warm.

• The AC adapter can interfere with radio reception so keep radios at least 1 meter away from it.

• The AC adapter may make some noise when you are using it, but this is normal.

• You cannot charge the battery when supplying power to the camera-recorder from the AC adapter.

• Operation of battery pack CGR-D16 (1600mAh) (sold separately) is not guaranteed.

Installing and removing the power supply

Installing and removing the battery

Installation

Insert the battery until it clicks into place.

Removal

1 Set the POWER switch to OFF, and check

2 Remove the battery while pressing the

Connecting and disconnecting the power cord

Installation

1 Connect the DC cord to the AC adapter.

Removal

1 Set the POWER switch to OFF, and check

2 Plug the AC power supply cord into the

power outlet.

2 Remove the DC cord’s battery connector

3 Insert the DC cord’s battery connector until

it clicks into place.

3 Disconnect the AC power supply cord from

that the mode lamp is off.

battery release button.

• Support the battery with your hand to ensure that it will not fall.

Battery release

Mode lamp

that the mode lamp is off.

while pressing the battery release button.

the power outlet.

button

Preparation

DC cord’s battery connector

• You cannot charge the battery when supplying power to the camera-recorder from the AC adapter.

CAUTION:

• This unit can be operated at a voltage in the range of 100-240V AC. An AC plug adapter may be required for voltages other than 120 V AC. If a conversion plug is required, consult with your dealer as to which one is to be purchased.

• Disconnect the AC power supply cord from the power outlet when the unit is not going to be used.

Adjusting the hand strap

Adjust the hand strap to suit your hand.

1 Open the cover and adjust the length. 2 Close the cover.

• Make sure the cover is fully closed.

Attaching the shoulder strap

Attach the shoulder strap and use it as a precaution against dropping the camera.

20 mm or more

Detaching and attaching the lens hood

Detaching the lens hood

• Loosen the screw and turn the lens hood counterclockwise to detach it.

Attaching the lens hood

• Turn the lens hood clockwise and fix in position with the screw.

• Be sure to attach the lens hood cap to protect the lens when not in use.

Screw

The remote control

Insert the battery

1 Push the catch in the direction shown by

arrow (1) to remove the holder.

2 Insert the battery with the “+” marked side

facing up.

3 Return the holder to its original position.

• When the battery (CR2025) has run out, replace it with a new one. (The battery lasts about one year, depending on the frequency of use.)

If the remote control unit fails to work even when

it is operated near the camera-recorder’s remote control sensor, the battery has run out.

• Keep the battery out of the reach of children.

Remote control setup

When using two camera-recorders simultaneously, set this camera-recorder and the remote control to either [VCR1] or [VCR2] so the remote control does not operate the wrong camera-recorder by mistake.

Setting

• Wireless remote control

Press the STOP (

at the same time to set the remote control unit for use with VCR1.

Alternatively, press the STOP (

(

) buttons at the same time to set the remote

control unit for use with VCR2.

When the battery in the remote control unit is

replaced, the remote control unit is set for use with VCR1.

• Camera

In the setup menus, OTHER FUNCTIONS

screen, REMOTE, set to VCR1 or VCR2. (Page

114)

If different settings are used for the camerarecorder and remote control unit, “REMOTE” lights in red on the viewfinder and LCD monitor.

VCR2 VCR1

) and STILL ADV ( ) buttons

) and STILL ADV

START/

DATE/

PHOTO

STOP

TIME

SHOT

OSD

COUNTER

RESET TITLE

REC A.DUB

PLAY/REW FF/

PAUS E

STILL ADV

STOP INDEX

VAR.

ZOOM

VOL +

PB.

ZOOM

SET

ITEM

MULTI/ P-IN-P

STILL ADV

INDEX

SELECT

STORE

OFF/ON

P.B.DIGITAL

Preparation

Turn on/off the camera

While pressing the lock release, move the POWER switch to ON or OFF.

Turn on the camera:

The mode lamp (CAMERA) lights red (CAMERA mode) and the camera is now in the shooting standby mode.

Turn off the camera:

The red mode lamp goes out.

• Power saving mode

The camera-recorder performs as follows when

you pause or leave it in standby mode for about 5 minutes, and do not perform any specified

operations. ON: The camera recorder turns off automatically. OFF: Do not switch OFF the camera. In the TAPE

mode, however, put the cylinder head alone in a stopped (standby) status.

See the setup menus, OTHER FUNCTIONS

screen, POWER SAVE (page 117) for details.

• When the operation mode buttons flash in

sequence starting with the top one and the power

then goes off, it means that there is no charge left

in the battery. Recharge the battery.

Mode button

MCR VCR

Mode lamp

CAMERA

OFF

DUBPC

Lock release

Tally lamp

The tally lamp can be made to light up during shooting by selecting “ON” as the REC LAMP set-ting in the OTHER FUNCTIONS screen. (Page

115) When the camera-recorder is in any of the following states, the tally lamp blinks.

• When an operation initiated by the remote control

unit has been received (8 blinks/sec.)

• When shooting starts in the TAPE mode (8 blinks/

sec.)

• When the end of the tape is reached (4 blinks/

sec.)

• When trouble occurs regarding tape running

systems (4 blinks/sec.)

• When the remaining battery capacity runs out (4

blinks/sec.)

• When the available recording space on the P2

card or tape or the battery power is low (1 blink/

sec.)

• When removing the P2 card during access (4

blinks/sec.)

• When there is no recording space left on the P2

card (4 blinks/sec.)

Tally lamp

Viewfinder

This camera has two viewfinders; one is a miniature LCD in the viewfinder and the other is a retractable 3.5-inch LCD. Use the viewfinder that best suits the application and shooting conditions.

• The brightness and hue may differ between the images appearing on the viewfinder and LCD monitor and those displayed on a TV monitor.

To see how the final images will appear, check

them on a TV monitor.

Fitting the eye cup

Attach the eye cup by aligning the projections on the eye cup holder and eye cup and fitting them together.

• Turning the eye cup after attaching it may cause the eye cup holder to come off. If the eyecup holder does come off, see “Cleaning the Viewfinder” (page 126) for details on how to refit it.

Using the viewfinder

1 Set the POWER switch to ON and check that

images appear in the viewfinder.

• Keep the LCD monitor closed.

2 Adjust the viewfinder’s angle so that the

screen is positioned where it is easiest to see.

• You can move the view finder out to about 90° perpendicular to the camera.

3 Adjust the diopter adjustment lever so

that you can see the characters on the viewfinder screen clearly.

Viewfinder diopter dial

Eye piece

Eye cup holder

Eye cup

Preparation

Projection

Do not point the eye piece at the sun.

Doing so may damage the parts inside.

Viewfinder (continued)

Using the LCD

1 Set the POWER switch to ON. 2 Press the OPEN button in the direction

shown by arrow (1) to open the LCD.

It can open out to 120 degrees. Do not try

to open it further as this will damage the camera.

3 Position the LCD monitor where it is easiest

to see.

• The monitor can be rotated 180° toward the lens and 90° toward you.

• Do not apply unnecessary force to the open LCD. This can damage the camera.

Emphasizing outlines

Emphasizing the outlines of the images you see in the viewfinder or on the LCD makes it easier to focus. Emphasizing the outlines does not effect the images you shoot.

1 In CAMERA mode, press EVF DTL.

• “EVF DTL ON” appears on the screen for about 2 seconds.

EVF DTL button

Press EVF DTL again to return to the original display. “EVF DTL OFF” appears on the screen for about 2 seconds.

• Ensure the LCD is fully closed.

• Both the LCD and viewfinder come on when you have rotated the LCD to face in the same direction as the lens for self-portrait shooting.

Adjusting the screen display

1 Set the POWER switch to ON. (Page 20) 2 Press the MENU button.

SET

Operation button

• For menu operation (Page 96)

• You can also use the menu buttons on the remote control. (Page 15)

3 Viewfinder adjustments

Set YES under EVF SET on the setting menu DISPLAY SETUP screen.

LCD monitor adjustments

Set YES under LCD SET on the setting menu DISPLAY SETUP screen.

4 Select the item to be set using the or

operation button.

5 Adjust the selected item using the or

operation button.

6 Press MENU three times to exit the menus.

Preparation

• You can return the settings for EVF SET and LCD SET to the factory settings by selecting the item and pressing COUNTER RESET (if it is possible to change the item at that time).

• The viewfinder remains on when you open the LCD if you have set the EVF MODE in the DISPLAY SETUP screen to ON.

• The viewfinder display can be in color or black and white. (See the setup menus, DISPLAY SETUP screen, EVF COLOR.) The resolution is the same for both of them.

Setting the calendar

The CLOCK SET value is recorded in the contents (clip), and affects the sequence of playback of the thumbnails. Before carrying out recording, be sure to check and set CLOCK SET and TIME ZONE. This shows you how to adjust the calendar to 5:20 PM on December 25, 2005.

1 Set the POWER switch to ON. (Page 20) 2 Press the MENU button. 3 In the setup menus, OTHER FUNCTIONS

screen, TIME ZONE, set the time difference from Greenwich mean time using the

operation button. (Page 116)

(Example of MENU in the TAPE mode)

SET

Operation button

• For menu operation (Page 96)

• You can also use the menu buttons on the remote control. (Page 15)

Press the operation button to move the

setting item to MONTH.

7 Press the or operation button to set

MONTH to DEC.

8 Set DAY, HOUR, and MIN using the method

shown in steps 4 and 5.

• This is a 24-hour clock.

4 In the setup menus, OTHER FUNCTIONS

screen, CLOCK SET, select YES.

5 Press the or operation button to set

YEAR to 2005.

Choose a year between 2000 and 2030.

9 Press MENU three times to exit the menus.

• The clock can vary in accuracy so check that the time is correct before shooting.

• When using the camera overseas, do not set the CLOCK option to the current time, but instead enter the time difference from Greenwich mean time according to TIME ZONE.

Basic shooting operations (P2 card)

Preparing to shoot using a P2 card

1 Switch the MEDIA switch to “P2”. 2 Set the POWER switch to ON. (Page 20) 3 Lift up the viewfinder and open the card slot

cover.

4 Insert the P2 card securely in the card slot.

• There are two card slots.

• Be absolutely sure to close the card slot covers to keep the dust out.

P2 TAPE

Lock release

Shooting in auto mode

1 Turn the POWER switch to ON. (Page 20)

• Check that the mode lamp (CAMERA) is lighted red. If not, press the mode button.

2 Switch the AUTO/MANUAL switch to AUTO

to select auto mode.

• “A” appears on the viewfinder and LCD screens.

• The focus, gain, iris and white balance are adjusted automatically.

3 Press the START/STOP button (Red) on the

POWER switch to start shooting.

• Press again to return to the camera to the shooting standby mode.

• Use the handle START/STOP button to make it easier to shoot from low angles.

LCD side

AUTO MANUAL

Handle START/STOP button

Shooting

Do not operate the MEDIA switch when the power is switched ON. If you attempt to operate the MEDIA switch, the message “TURN POWER OFF” will be displayed. In this case, switch OFF the power, and then switch it ON again.

Mode button

CAMERA

MCR VCR

Mode lamp

REC CHECK button

DUBPC

Lock release

Basic shooting operations (P2 card) (continued)

Checking photos taken (REC CHECK)

In the shooting pause mode, press the REC CHECK button.

A few seconds of the last thing you shot play.

• Note that this REC CHECK portion will also be recorded to any equipment you have set up to make backup recordings.

• Only the POWER and START/STOP buttons are operable during REC CHECK.

• The REC CHECK function does not work when PC, MCR or DUB has been selected as the operation mode.

The HD recording(720P/60P) settings are already made in the default mode. (To view the current settings, see page 44.)

P2 card access lamps

CAMERA mode (MCR) Lights green: Data can be saved onto the cards or

loaded from them.

Blinks green (slow): No available space on card,

card is write-protected

Lights orange: Slot that is the object of recording Blinks orange : Data is now being accessed. Blinks orange (fast): A card is now being

recognized.

Both lamps blink orange: Ejection of card during

access

Off: Cards have not been inserted or formatted.

Insertion of incompatible card.

P2 card access lamp

Protecting against a possible erasure

Switch the write-protect switch of the P2 card to [PROTECT].

Write-protect switch

PROTECT

PC mode (USB DEVICE) Blinks orange: Data is now being accessed. Off: A status other than access underway.

PC mode (1394 DEVICE) Blinks orange: Connected Off: Not connected

PC mode (1394 HOST) Lights green: Access standby. Blinks orange: Data is now being accessed. Off: Cards have not been inserted or formatted.

Insertion of incompatible card.

Formatting P2 cards

1 Press the mode button and set it to MCR

mode (the MCR/VCR lamp lights).

• Thumbnails are displayed.

2 Press the MENU button.

SET

Operation button

MENU button

Mode button

CAMERA

MCR VCR

DUBPC

Mode lamp

3 On the menu, select OPERATION and then

FORMAT. (Page 69)

• A screen such as the one shown below appears. Select the number of the slot into which you inserted the P2 card to be formatted. Select EXIT to cancel the formatting.

• When you press the MENU button, the menu display disappears.

4 Select YES on the confirmation screen.

• The selected P2 card is formatted.

Recording times

Card model Capacity

AJ-P2C004HG 4 GB approx. 16 min. approx. 8 min. approx. 4 min. approx. 10 min. approx. 8 min.

AJ-P2C008HG 8 GB approx. 32 min. approx. 16 min. approx. 8 min. approx. 20 min. approx. 16 min.

• The AJ-P2C002SG (2 GB) card cannot be used.

• The displayed available space includes the management area, and so the space available for recording is smaller than this.

• Concerning the division of clips recorded on P2 cards

When using a P2 card of at least 8 GB in this camera, if the continuous recording time for a single

session exceeds the time shown in the following table, recording will be automatically resumed as a different clip. When performing a thumbnail operation (display, delete, restore, copy, etc.) on clips using P2 cards, you can operate them as a single clip. When you are using non-linear editing software and a PC, for example, the clips are displayed individually.

Recording Format Recording times

DVPRO HD

DVPRO50 approx. 10 min.

DVPRO/DV approx. 20 min.

• When using any other types of cards, the driver installed in the camera-recorder may need to be updated. (Page 125)

• For the latest information not available in the Operating Instructions, visit the P2 Support Desk at the following Web sites.

https://eww.pavc.panasonic.co.jp/pro-av/

∗

DVCPRO

2-channel

audio

approx. 5 min.

DVCPRO50

4-channel

audio

*1 The 720P/30PN and 720P/24PN formats are not

DVCPRO HD

included in the DVCPRO HD recording format.

DVCPRO HD

∗

720P/24PN

DVCPRO HD

720P/30PN

Shooting

Basic shooting operations (P2 card) (continued)

Remove the P2 card

1 Lift up the viewfinder and open the card slot

cover.

• Check that the P2 card access lamp is not blinking orange.

2 Press the card eject button once, and when

the button has popped back up, press it again.

3 Remove the P2 card.

Card eject button

• Do not eject the P2 card or turn the power off under the following circumstances, since doing so may cause a malfunction in the card:

1) While the orange P2 card access lamp is

blinking after the card is inserted (and until it stops blinking).

2) While the access lamp is blinking during a

recording.

• If a P2 card is ejected during formatting or while its data is being accessed, “TURN POWER OFF” appears in the viewfinder, and a warning is indicated by an alarm or tally lamp. If this happens, turn the power off and back on again.

When a card is ejected during formatting:

Format the card again.

When a card is ejected while its data is being

accessed:

The data on the card will not be destroyed, but

the clips may be thrown out of order. Check the clips and repair them. (For details on repairing clips, see page 69.)

• During playback, a P2 card inserted into the empty slot will not be recognized and the P2 card access lamp will not light. When playback is completed, the P2 card recognition will begin.

• You can use ACCESS LED on the OTHER FUNCTIONS screen to set the P2 card access lamps so that they will always be off. In this case, either turn off the power or wait until enough time has passed after inserting the cards or stopping operation before ejecting the cards.

• If a P2 card is ejected while thumbnails are displayed, the thumbnail screen is released.

Basic shooting operations (Cassette tape)

TAPE

Preparing to shoot using a tape

1 Switch the MEDIA switch to “TAPE”. 2 Set the POWER switch to ON. (Page 20) 3 Slide the OPEN/EJECT switch in the

direction shown by the arrow to open the cassette cover.

• The cassette holder opens automatically.

• The cassette holder will not open if the camera is not supplied with power (AC adapter or a battery).

4 Insert the cassette tape. 5 Press PUSH to close the cassette holder.

• Close the cassette cover only after the cassette holder is completely in position.

Lock release

Shooting in auto mode

1 Turn the POWER switch to ON. (Page 20)

• Check that the mode lamp (CAMERA) is lighted red. If not, press the mode button.

2 Switch the AUTO/MANUAL switch to AUTO

to select auto mode.

• “A” appears on the viewfinder and LCD screens.

• The focus, gain, iris and white balance are adjusted automatically.

3 Press the START/STOP button (Red) on the

POWER switch to start shooting.

• Press again to return to the camera to the shooting standby mode.

• Use the handle START/STOP button to make it easier to shoot from low angles.

LCD side

AUTO MANUAL

Handle START/STOP button

Shooting

P2 TAPE

Mode button

CAMERA

MCR VCR

Mode lamp

REC CHECK button

DUBPC

Lock release

Basic shooting operations (Cassette tape) (continued)

Checking scenes taken (REC CHECK)

In the shooting pause mode, press the REC CHECK button.

A few seconds of the last thing you shot play, and then the camera returns to the shooting pause mode.

• The REC CHECK function cannot be used unless the recording is at least one second long.

• When recording backup images by connecting the equipments using a 1394 cable, the images will not appear during REC CHECK.

• The REC CHECK function does not work when VCR or DUB has been selected as the operation mode.

TAPE

Remove the cassette tape

1 Slide the OPEN/EJECT switch in the

direction shown by the arrow to open the cassette cover.

• The cassette holder opens automatically.

• The cassette holder will not open if the camera is not supplied with power (AC adapter or battery).

• A tape cannot be ejected in P2 mode or during recording in TAPE mode.

2 Remove the cassette. 3 Press PUSH to close the cassette holder.

• Close the cassette cover only after the cassette holder is completely in position.

PUSH

+ 104 hidden pages

Panasonic AG-HVX200 User Manual

Software information for this product

IMPORTANT SAFETY INSTRUCTIONS

Contents

Outline of operations

Read this first!

Accessories

About this manual

Description of parts

Right side and rear side

Left side

Terminals and mounting parts

Remote control

The battery

Charging

Installing and removing the power supply

Installing and removing the battery

Connecting and disconnecting the power cord

Adjusting the hand strap

Attaching the shoulder strap

Detaching and attaching the lens hood

The remote control

Insert the battery

Remote control setup

Turn on/off the camera

Tally lamp

Viewfinder

Using the viewfinder

Using the LCD

Emphasizing outlines

Adjusting the screen display

Setting the calendar

Basic shooting operations (P2 card)

Preparing to shoot using a P2 card

Shooting in auto mode

Checking photos taken (REC CHECK)

P2 card access lamps

Protecting against a possible erasure

Formatting P2 cards

Recording times

Remove the P2 card

Basic shooting operations (Cassette tape)

Preparing to shoot using a tape

Shooting in auto mode

Checking scenes taken (REC CHECK)

Remove the cassette tape