Onkyo TX-NR1010 User Manual

Contents

AV RECEIVER

TX-NR1010

Instruction Manual

Safety Information and Introduction ............2

Table of Contents...........................................6

Connections .................................................13

Turning On & Basic Operations..................23

Advanced Operations ..................................54

Controlling Other Components...................88

Appendix.......................................................97

Internet Radio Guide

Remote Control Codes

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons. The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand,

PORTABLE CART WARNIN

tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

S3125A

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power-supply cord or plug is damaged, B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or water,

Safety Information and Introduction

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus. Don’t put candles or other burning objects on top of this unit.

17. Batteries Always consider the environmental issues and follow local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation. Leave 20 cm (8") of free space at the top and sides and 10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

En-2

Precautions

1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your Onkyo dealer.

3. Care—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power WARNING

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [POWER] button, or with both [POWER] and [ON/STANDBY] buttons: Pressing the [POWER] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [ON/STANDBY] button only: Pressing the [ON/STANDBY] button to select Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure Warning

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a

long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after

prolonged use. This is normal.

• If you do not use this unit for a long time, it may not

work properly the next time you turn it on, so be sure to use it occasionally.

Safety Information and Introduction

For U.S. models

FCC Information for User CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

En-3

Safety Information and Introduction

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003. For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

For British models

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse needs to be replaced, the replacement fuse must approved by ASTA or BSI to BS1362 and have the same ampere rating as that indicated on the plug. Check for the ASTA mark or the BSI mark on the body of the fuse.

If the power cord’s plug is not suitable for your socket outlets, cut it off and fit a suitable plug. Fit a suitable fuse in the plug.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY

declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3.

GROEBENZELL, GERMANY

K. MIYAGI

ONKYO EUROPE ELECTRONICS GmbH

En-4

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (➔ page 21) AM loop antenna (➔ page 21)

(North American models) Two AM loop antennas and two Indoor FM antennas are supplied.

Power cord (➔ page 22) Speaker cable labels (➔ page 14) Speaker setup microphone (➔ page 40) Remote controller (RC-840M) and two batteries (AA/R6) Quick Start Guide

In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

■ Installing the batteries

Safety Information and Introduction

■ Aiming the remote controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference.

Batteries (AA/R6)

Note

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

En-5

Safety Information and Introduction

Important Safety Instructions ......................................2

Precautions ...................................................................3

Supplied Accessories...................................................5

Table of Contents..........................................................6

Features.........................................................................7

Front & Rear Panels......................................................8

Remote Controller.......................................................12

Connections

Connecting the AV Receiver......................................13

Connecting Your Speakers .......................................13

About AV Connections..............................................17

Connecting Components with HDMI .........................18

Connecting Your Components ..................................19

Connecting the Antennas..........................................21

Connecting Onkyo RI Components...........................22

Connecting the Power Cord ......................................22

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................23

Turning On ................................................................23

Turning Off ................................................................23

Initial Setup..................................................................24

Selecting the Language

for the Onscreen Setup Menus...............................24

Audyssey MultEQ XT32: Auto Setup ........................24

Source Connection....................................................25

Remote Mode Setup .................................................25

Network Connection..................................................25

Terminating the Initial Setup .....................................25

Playback ...................................................................... 26

Playing the Connected Component ..........................26

Controlling Contents of USB or Network Devices..... 27

Understanding Icons on the Display ......................... 28

Playing an iPod/iPhone via USB............................... 28

Playing a USB Device............................................... 29

Listening to vTuner Internet Radio............................ 29

Registering Other Internet Radio .............................. 30

Changing the Icon Layout

on the Network Service Screen.............................. 31

Playing Music Files on a Server (DLNA) ..................31

Remote Playback...................................................... 32

Playing Music Files on a Shared Folder ...................33

Listening to AM/FM Radio ........................................34

Playing Audio and Video from Separate Sources..... 38

Using Basic Functions............................................... 39

Using the Automatic Speaker Setup......................... 39

Using the Listening Modes .......................................42

Using the Home Menu .............................................. 50

Using the Sleep Timer ..............................................51

Setting the Display Brightness.................................. 51

Displaying Source Information.................................. 51

Changing the Input Display....................................... 51

Using the Whole House Mode .................................. 52

Selecting Speaker Layout.........................................52

Muting the AV Receiver ............................................ 52

Using Headphones ...................................................52

Using Easy Macros................................................... 53

Advanced Operations

On-screen Setup......................................................... 54

Using the Quick Setup .............................................. 54

Using the Audio Settings of Quick Setup..................55

Using the Setup Menu (HOME) ................................ 58

About the HYBRID STANDBY Indicator ................... 59

Setup Menu Items..................................................... 59

Input/Output Assign ..................................................60

Speaker Setup .......................................................... 63

Audio Adjust.............................................................. 68

Source Setup ............................................................ 72

Listening Mode Preset .............................................. 77

Miscellaneous ........................................................... 78

Hardware Setup........................................................ 79

Remote Controller Setup ..........................................82

Lock Setup................................................................ 82

Safety Information and Introduction

Multi Zone ................................................................... 83

Making Multi Zone Connections ............................... 83

Controlling Multi Zone Components ......................... 85

Using the Remote Controller in

Zone and Multiroom Control Kits ........................... 86

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock .................... 88

Using the Onkyo Dock.............................................. 88

Controlling Your iPod/iPhone ................................... 89

Controlling Other Components................................. 90

Preprogrammed Remote Control Codes .................. 90

Looking up for Remote Control Codes ..................... 90

Entering Remote Control Codes............................... 91

Remapping Colored Buttons .................................... 91

Remote Control Codes

for Onkyo Components Connected via RI ............. 92

Resetting the REMOTE MODE Buttons ................... 92

Resetting the Remote Controller .............................. 92

Controlling Other Components ................................. 92

Learning Commands ................................................ 95

Using Normal Macros ............................................... 96

Appendix

Troubleshooting ......................................................... 97

Firmware Update ......................................................103

Connection Tips and Video Signal Path ................ 107

Using an RIHD-compatible TV, Player,

or Recorder ............................................................ 111

About HDMI............................................................... 113

Network/USB Features............................................. 114

License and Trademark Information ...................... 117

Specifications........................................................... 118

To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT, press

8ON/STANDBY (➔ page 97).

En-6

Safety Information and Introduction

Features

Amplifier

• 140 Watts/Channel @ 8 ohms (FTC)

• 200 Watts/Channel @ 6 ohms (IEC)

• WRAT–Wide Range Amplifier Technology (5 Hz to 100 kHz bandwidth)

• Linear Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High Power Transformer

• 3 Stage Inverted Darlington Amplifier Design

Processing

• THX Ultra2 Plus Certified

• Incorporates Qdeo™ technology for HDMI Video Upscaling (to 4K Compatible)

• HQV

• HDMI (Audio Return Channel, 3D, DeepColor,

• Dolby TrueHD and DTS-HD Master Audio

• Dolby Pro Logic IIz and Audyssey DSX

• DTS Neo:X

• Non-Scaling Configuration

• A-Form Listening Mode Memory

•Direct Mode

• Pure Audio Mode

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

• Digital Processing Crossover Network

• DSD Direct for Super Audio CD

-Vida Video Processing with 1080p Video

upscaling of All Video Sources via HDMI

x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD High Resolution Audio, Dolby TrueHD, Dolby Digital Plus, DSD and Multi-CH PCM)

Connections

• 9 HDMI Inputs (1 on front panel) and 2 Outputs

• Zone 2 HDMI Output

• Onkyo p for System Control

• 6 Digital Inputs (3 Optical/3 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Banana Plug-Compatible Speaker Posts

In Europe, using banana plugs to connect speakers to an audio amplifier is prohibited.

• Powered Zone 2/3

• Bi-Amping Capability for FL/FR with FHL/FHR

• Analog RGB Video Input (D-sub 15) for PC

• 2 Independent Subwoofer Pre Outs

• (North American models) HD Radio Capability

• Internet Radio Connectivity

• Network Capability for Streaming Audio Files

• 2 USB Inputs (Front/Rear) for Memory Devices and

iPod

/iPhone® models

Only the front-panel USB input is compatible with iPod/iPhone.

• MHL-Enabled AUX Front Input

Miscellaneous

• 40 FM/AM Presets

• Dolby Volume

• Audyssey MultEQ problems

• Audyssey Dynamic EQ

• Audyssey Dynamic Volume listening level and dynamic range

• Crossover Adjustment (40/45/50/55/60/70/80/90/100/110/120/130/150/200 Hz)

• A/V Sync Control Function (up to 800 ms)

• Auto Standby Function

• On-Screen Display via HDMI

• Preprogrammed (with onscreen display setup) RI-Compatible Learning Remote with 4 Activities and Mode-Key LEDs

• ISF (Imaging Science Foundation) Video Calibration

• VLSC (Vector Linear Shaping Circuitry) for All Channels

XT32 to correct room acoustic

for loudness correction

to maintain optimal

En-7

Front & Rear Panels

Front Panel

Safety Information and Introduction

ba

(North American models) (European models)

ij l m o p tq sn

k r

d e

u w x yv

En-8

For detailed information, see the pages in parentheses.

a 8ON/STANDBY button (23) b Remote control sensor (5) c Display (10) d MASTER VOLUME control and indicator (26, 51) e HYBRID STANDBY indicator (59) f PURE AUDIO button and indicator (42) g Input selector buttons (26) h Front flap

Gently push on the lower end of the front panel to open the flap.

Safety Information and Introduction

i PHONES jack (52) j ZONE 2, ZONE 3, and OFF buttons (85) k TONE and Tone Level buttons (55) l MONITOR OUT button (60) m DISPLAY button (51) n TUNING q/w (34), PRESET e/r (34), cursor and

enter (middle) buttons

o DIMMER button (North American models) (51) p MEMORY button (34) q TUNING MODE button (34) r LISTENING MODE buttons (42) s WHOLE HOUSE MODE button (52) t SETUP MIC jack (40) u SETUP button (58) v HOME button (50) w RETURN button x USB port (19) y AUX INPUT jacks (18, 19) z RT/PTY/TP button (European models) (37)

En-9

Display

Safety Information and Introduction

dcb fe hga i

lj m n o pqk

For detailed information, see the pages in parentheses.

a Speaker/channel indicators b Z2 (Zone 2) indicator (85) c Z3 (Zone 3) indicator (85) d Listening mode and format indicators (42, 77) e M.Opt indicator (57) f 1, 3 and cursor indicators (28) g NET indicator (29 to 33, 82) h Tuning indicators

HD indicator (North American models) (35) SPS indicator (North American models) (35) RDS indicator (excluding North American models)

(36) AUTO indicator (34) TUNED indicator (34) FM STEREO indicator (34)

i Input indicators (109)

HDMI indicator (80) DIGITAL indicator ANALOG indicator

j Bi AMP indicator k Audyssey indicator (39, 72)

Dynamic EQ indicator (72)

- (Dolby) Vol indicator Dynamic Vol indicator (73)

l Headphone indicator (52) m Message area n MUTING indicator (52) o Volume level p USB indicator (28, 29) q SLEEP indicator (51)

En-10

Rear Panel

(North American models) (European models)

Safety Information and Introduction

p qtsro

a RS232 port

Terminal for control.

b DIGITAL IN COAXIAL and OPTICAL jacks c USB port d ETHERNET port e uREMOTE CONTROL jack f HDMI IN and HDMI output (HDMI OUT MAIN and

HDMI OUT SUB/ZONE 2) jacks

g COMPONENT VIDEO IN and MONITOR OUT

jacks

h IR IN and OUT jacks i ZONE 2 and ZONE 3 12V TRIGGER OUT jacks j ZONE 2 OUT V jack

ih je f mla b c d

k ZONE 2 and ZONE 3 LINE OUT jacks l MAIN/ZONE 2 FM ANTENNA jacks and

MAIN/ZONE 2 AM ANTENNA terminals

m PC IN jack n AC INLET o GND screw p Composite video and analog audio jacks

(BD/DVD IN, CBL/SAT IN, STB/DVR IN, GAME 1 IN, PC IN, TV/CD IN and PHONO IN)

q MONITOR OUT V jack

r PRE OUT jacks

(FRONT L/R, CENTER, SURR L/R, SB/FH/FW L/R, SW1 and SW2)

SB···Surround Back, FH···Front High, FW···Front Wide

s SB/FH/FW*1 EXT AMP jacks t Speaker Terminals

(FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, FRONT HIGH/ZONE 3 L/R and FRONT WIDE/ZONE 2 L/R)

u FM ANTENNA jack and AM ANTENNA terminal

See “Connecting the AV Receiver” for connection (➔ pages 13 to 22).

En-11

Remote Controller

Controlling the AV Receiver

a b

d e

l m

Safety Information and Introduction

To control the AV receiver, press RECEIVER to select Receiver mode. You can also use the remote controller to control Onkyo Blu-ray Disc/DVD player, CD player, and other components. See “Entering Remote Control Codes” for more details (➔ page 91).

For detailed information, see the pages in parentheses.

a 8 RECEIVER button (23)

b ACTIVITIES buttons (53, 96) c REMOTE MODE/INPUT SELECTOR buttons (26) d SP (speaker layout) button (52) e q/w/e/r and ENTER buttons f Q SETUP button (54) g Listening Mode buttons (42) h DIMMER button (51) i DISPLAY button (51) j MUTING button (52) k VOL q/w button (26) l RETURN button m HOME button (50) n SLEEP button (51)

■ Controlling the tuner

To control the AV receiver’s tuner, press TUNER (or RECEIVER).

You can select AM or FM by pressing TUNER repeatedly.

a q/w buttons (34) b D.TUN button (34) c DISPLAY button d CH +/– button (35) e Number buttons (34)

When you want to change the remote controller mode (target component) without changing the current input source, press MODE and within about 8 seconds, press REMOTE MODE. Then, using the same AV receiver’s remote controller, you can control the component corresponding to the button you pressed.

These buttons can also be used when a REMOTE MODE other than Receiver mode is selected.

En-12

Connections

Connecting the AV Receiver

Connecting Your Speakers

Speaker Configuration

The following table indicates the channels you should use depending on the number of speakers that you have. No matter how many speakers you use, 2 powered subwoofers are recommended for a really powerful and solid bass. To get the best from your surround sound system, you need to set the speaker settings automatically (➔ page 39) or manually (➔ page 64).

Number of speakers

Front speakers ✔✔✔✔✔✔✔✔✔✔✔✔✔✔ ✔ Center speaker ✔ ✔✔✔✔✔✔✔✔✔✔✔ ✔ Surround

speakers Surround back

speaker Surround back

speakers Front high

speakers Front wide

speakers

If you’re using only one surround back speaker, connect it to the SURR BACK L terminals.

2 3 4 5 6 7 7 7 8 8 9 9 9 10 11

✔✔✔✔✔✔✔✔✔✔✔✔ ✔

✔✔✔✔

✔✔✔✔✔✔

Connecting the Speaker Cables

■ 7.2-channel playback

The following illustration shows how to connect the speakers to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK L terminals. Select the speakers (surround back, front high, front wide) you want to use for 7.2-channel playback. You can set which speakers you want to use by priority. See “Selecting Speaker Layout” (➔ page 52).

Front high

right Front leftFront right Center

Surround

right

Front wide

right

Surround

back right

■ Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

1/2" to 5/8" (12 to 15 mm)

Front wide

left

Surround

back left

■ Banana Plugs (North American models)

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Front high

left

Surround

left

En-13

■ 9.2-channel playback

By adding an external amplifier to the 7.2-channel configuration, you can enjoy 9.2-channel playback.

Connect your power amplifier’s analog audio input jacks to the AV receiver’s SB/FH/FW

EXT AMP jacks with

audio cables. To use the SB/FH/FW EXT AMP jacks, you must specify their channel with the “Preout to External Amplifier” setting (➔ page 64).

You can set which speakers you want to use by priority. See “Selecting Speaker Layout” (➔ page 52).

SB···Surround Back, FH···Front High, FW···Front Wide

Power amplifier

Surround back right/

Front high right/ Front wide right

Surround back left/

Front high left/ Front wide left

Attaching the Speaker Cable Labels

The speaker terminals are color-coded for identification purpose.

Speaker Color

Front left, Front high left, Front wide left, Zone 2 left, Zone 3 left

Front right, Front high right, Front wide right, Zone 2 right, Zone 3 right

Center Green Surround left Blue Surround right Gray Surround back left Brown Surround back right Tan

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

White

Red

Connections

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between 4 and 16 ohms. If the impedance of any of the connected speakers is 4 ohms or more, but less than 6 ohms, be sure to set the minimum speaker impedance to “4ohms” (➔ page 63). If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires. Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver.

En-14

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

Using Dipole Speakers

TV/screen

Connections

Using Powered Subwoofers

You can use dipole speakers for the surround and surround back speakers. Dipole speakers output the same sound in two directions. Dipole speakers typically have an arrow printed on them to indicate how they should be positioned. The surround dipole speakers (a) should be positioned so that their arrows point toward the TV/screen, while the surround back dipole speakers (b) should be positioned so that their arrows point toward each other, as shown.

LINE INPUT

Powered subwoofer

1/3 of wall

position

LINE INPUT

Corner position

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

You can connect the powered subwoofers with SW1 PRE OUT and SW2 PRE OUT respectively.

The level and distance can be set individually for each output. If you’re using only one subwoofer, connect it to

SW1 PRE OUT.

Tip

• If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

En-15

Connections

Bi-amping the Front Speakers

Important:

• When making the bi-amping connections, be sure to remove the jumper bars that link the speakers’ tweeter (high) and woofer (low) terminals.

• Bi-amping can be used only with speakers that support biamping. Refer to your speaker manual.

Bi-amping provides improved bass and treble performance. When bi-amping is used, the AV receiver is able to drive up to a 5.2 speaker system in the main room. Once you’ve completed the bi-amping connections as

shown and turned on the AV receiver, you must set the speaker setting to enable bi-amping (➔ page 63).

Tweeter (high)

Woofer (low)

Using Speakers Without Crossover Network

Important:

• Speakers without crossover network are speakers with no built-in crossover network.

• With speakers without crossover network, be careful NOT to connect tweeters and woofers the wrong way around, as this may damage your speakers.

• With speakers without crossover network, be careful NOT to set “Speakers Type(Front)” to “Bi-Amp” as this may damage your speakers. Make sure that this setting is set to “Digital Crossover”.

• Confirm that your speakers are without crossover network by referring to your speaker manual.

Connecting speakers without crossover network provide a fine, three-dimensional sound field that extends bass and treble performance to the fullest extent. When speakers without crossover network are used, the AV receiver is able to drive up to a 5.2 speaker system in the main room. You must enable “Digital Crossover” in “Speakers Type(Front)” (➔ page 63) and make the settings of “Digital Processing Crossover Network” (➔ page 67).

Note

• You need to make the setting before connecting the speakers.

Connecting a Power Amplifier

If you want to use a more powerful power amplifier, you can use the AV receiver as a preamp. Connect all speaker outputs to the power amplifier. See the manuals supplied with your amplifier for details.

Power amplifier

SB···Surround Back, FH···Front High, FW···Front Wide

Note

•Specify “None” for any channel that you don’t want to output

(➔ page 64).

• When connecting to the SB/FH/FW EXT AMP jacks, you must set the “Preout to External Amplifier” setting (➔ page 64).

Front right Front left

Tweeter (high)

Woofer (low)

Front right Front left

En-16

About AV Connections

Connecting AV components

HDMI cable

TV, projector, etc.

Blu-ray Disc/

DVD player

Other cables

TV, projector, etc.

Blu-ray Disc/

DVD player

If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

AV receiver

: Video

AV receiver

: Video & Audio

Game console

: Audio

Game console

• Push plugs in all the way to make

Right!

good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power

Wrong!

cords and speaker cables.

AV Cables and Jacks

■ HDMI

HDMI connections can carry digital video and audio.

■ Component video

Component video separates the luminance (Y) and color difference signals (P quality (some TV manufacturers label their component video sockets slightly differently).

■ Analog RGB

This is a conventional analog interface to connect a PC and a display device (also called D-Sub or D-subminiature).

■ Composite video

Composite video is commonly used on TVs, DVDs, and other video equipment.

B, PR), providing the best picture

Green

Blue

Red

Yellow

Connections

■ Optical digital audio

Optical digital connections allow you to enjoy digital sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as coaxial.

■ Coaxial digital audio

Coaxial digital connections allow you to enjoy digital

sound such as PCM

, Dolby Digital or DTS. The audio

quality is the same as optical.

Orange

■ Analog audio (RCA)

Analog audio connections (RCA) carry analog audio.

White

Red

For PCM signals, the supported sampling rates are 32/44.1/48/88.2/96 kHz. With HDMI connections, 176.4 and 192 kHz are also supported.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

En-17

Connecting Components with HDMI

Satellite/cable set-top box, etc.

Connections

Personal computer

Game console

Set top box/digital video recorder, etc.

If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.

When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

TV, projector, etc.

Blu-ray Disc/DVD player

Connect your components to the appropriate jacks. The default input assignments are shown below.

✔: Assignment can be changed (➔ page 61).

Jack Components

IN1 Blu-ray Disc/DVD player ✔ IN2 Satellite/cable set-top box, etc. ✔ IN3 Set top box/digital video recorder, etc. ✔ IN4 Game console ✔ IN5 Game console ✔ IN6 Personal computer ✔ IN7 Other components ✔ IN8 Other components ✔ Front Camcorder, etc. OUT MAIN TV OUT SUB Projector, etc.

Connecting Your Components

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

BA

C

D A E F G IH

Connections

Connect your components to the appropriate jacks. The default input assignments are shown below. See “Connection Tips and Video Signal Path” for more information (➔ page 107).

✔: Assignment can be changed (➔ page 62, 63).

No. Jack/Port Components

*1*2

USB

USB, AUX INPUT

E F

VIDEO AUX INPUT VIDEO Camcorder, etc AUDIO L/R DIGITAL DIGITAL IN COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player ✔ COAXIAL 2 (CBL/SAT) Satellite/cable set-top box,

COAXIAL 3 (STB/DVR) Set top box/digital video

OPTICAL 1 (GAME 1) Game consoles ✔ OPTICAL 2 (TV/CD) TV, CD player ✔ ETHERNET Router MONITOR OUT TV, projector, etc. BD/DVD IN Blu-ray Disc/DVD player CBL/SAT IN Satellite/cable set-top box,

STB/DVR IN Set top box/digital video

GAME 1 IN Game console, RI dock PC IN Personal computer TV/CD IN TV, CD player, cassette

PHONO IN

iPod/iPhone, MP3 player, USB flash drive

iPod/iPhone (video playback)

etc.

recorder, etc

etc.

recorder, etc

tape deck, MD, CD-R, Turntable

Turntable

, RI dock

✔

GND screw

To be continued

En-19

No. Jack/Port Components

COMPONENT VIDEO

MONITOR OUT TV, projector, etc. IN 1 (BD/DVD) Blu-ray Disc/DVD player,

IN 2 (CBL/SAT) Satellite/cable set-top box,

ZONE 2 OUT TV, projector, etc.

H I

Note

PC IN

Do not connect the AV receiver’s USB port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way. Only the front-panel USB input is compatible with iPod/iPhone. When the USB input is selected, you can input video signals from the AUX INPUT VIDEO jack. Video signals input from

AUX INPUT VIDEO will be output from MONITOR OUT V, COMPONENT VIDEO MONITOR OUT, and the HDMI

output jacks. Select which of COMPONENT VIDEO MONITOR OUT and the HDMI output jacks will output the video signal in the “Monitor Out” setting (➔ page 60). Connect a turntable (MM) that has a built-in phono preamp to TV/CD IN, or connect it to PHONO IN with the phono preamp turned off. If your turntable (MM) doesn’t have a phono preamp, connect it to PHONO IN. If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s manual for details. If your turntable has a ground wire, connect it to the AV receiver’s GND screw. With some turntables, connecting the ground wire may produce an audible hum. If this happens, disconnect it. When you connect your personal computer to PC IN and select the PC input selector, the video of the personal computer is output from the HDMI outputs. However, if you have assigned the HDMI inputs to the PC input selector, the AV receiver will output signals received from the HDMI inputs instead of signals from PC IN, based on the priority order of HDMI > component video > PC IN (analog RGB). To have the signals

RI dock

RI dock, etc.

Personal computer

output from PC IN, select “-----” for “PC” in the “HDMI Input” setting (➔ page 61).

• With connection D, you can enjoy Dolby Digital and

✔

DTS. (To listen in Zone 2/3 as well, use D and F.)

• With connection F, you can enjoy analog video from

✔

external components while you are in Zone 2.

• With connection F, you can enjoy audio from external components while you are in Zone 2/3.

• With connection F, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect the main stereo.

Connections

En-20

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

Connections

(North American models)

Push. Insert wire. Release.

Assembling the AM loop antenna

Insert the plug fully into the jack.

Caution

• Be careful not to injure

(European models)

Push. Insert wire. Release.

Assembling the AM loop antenna

yourself when using thumbtacks.

Thumbtacks, etc.

Indoor FM antenna (supplied)AM loop antenna (supplied)

Tip

• If you want to select different radio stations for the main room and Zone 2 respectively, connect the

indoor FM antenna or AM loop antenna to the ZONE 2 FM ANTENNA jack or the ZONE 2 AM

ANTENNA terminal.

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Insert the plug fully into the jack.

Caution

• Be careful not to injure yourself when using thumbtacks.

Thumbtacks, etc.

Indoor FM antenna (supplied)AM loop antenna (supplied)

En-21

Connections

Connecting Onkyo RI Components

Make sure that each Onkyo component is

connected with an analog audio cable (connection

F in the hookup examples) (➔ page 19).

Make the u connection (see the illustration).

If you’re using an RI Dock, or cassette tape deck,

change the Input Display (➔ page 51).

With u (Remote Interactive), you can use the following special functions:

■ Auto Power On

When you start playback on a component connected via u, while the AV receiver is on standby, the AV

receiver will automatically turn on and select that component as the input source.

■ Direct Change

When playback is started on a component connected via u, the AV receiver automatically selects that

component as the input source.

■ System Off

When you turn off the AV receiver, the components turn off automatically.

■ Remote Control

You can use the AV receiver’s remote controller to control your other u-capable Onkyo components,

pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first (➔ page 92).

e.g., cassette tape deck

RI Dock

Note

•Use only u cables for u connections. u cables are supplied with Onkyo components.

• Some components have two u jacks. You can connect either one to the AV receiver. The other jack is for connecting

additional u-capable components.

• Connect only Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all u functions. Refer to the manuals supplied with your Onkyo components.

• While Zone 2/3 is on, the System Off, Auto Power On and Direct Change u functions do not work.

ANALOG

AUDIO OUT

ANALOG

AUDIO OUT

Connecting the Power Cord

Connect the supplied power cord to the AV

receiver’s AC INLET.

To AC wall outlet

Plug the power cord into an AC wall outlet.

Note

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

• Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

• Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

En-22

Turning On & Basic Operations

Turning On/Off the AV Receiver

8ON/STANDBY

8RECEIVER

Turning On

Press 8ON/STANDBY on the front panel.

Press RECEIVER followed by 8RECEIVER on the remote controller.

The AV receiver comes on and its display lights.

Turning Off

Press 8ON/STANDBY on the front panel.

Press RECEIVER followed by 8RECEIVER on the remote controller.

The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip

•The HYBRID STANDBY indicator may light depending on the status of settings (➔ page 59).

• For details on power management settings, see “Auto Standby” (➔ page 81).

■ Smooth Operation in a Few Easy Steps

(Initial Setup)

To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for the very first time. These settings only need to be made once. See “Initial Setup” for details (➔ page 24).

■ If the “Firmware Update Available” window

appears.

When a new version of the firmware is available, the notification window “Firmware Update Available” pops up. This notification only appears when the AV receiver is connected to your home network (➔ page 114). To perform the firmware update, follow the instructions on screen.

Use q/w and ENTER on the AV receiver or remote controller to select one of the options.

` Update Now:

Starts the firmware update. Refer to “Firmware Update” (➔ page 103).

` Remind me Later:

The update notification will pop up again the next time you turn the AV receiver on.

` Never Remind me:

Disables the automatic update notification.

Tip

• The update notification window can be enabled or disabled in

“Update Notice” (➔ page 82).

RECEIVER

En-23

Turning On & Basic Operations

Initial Setup

This section explains the settings that we recommend you to make before using the AV receiver for the very first time. A setup wizard is launched upon first-time use to let you perform those settings.

The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN.

Selecting the Language for the Onscreen Setup Menus

This step determines the language used for the onscreen setup menus. See “Language” in “OSD Setup” (➔ page 79).

Tip

• Pressing HOME will close the setup wizard. To restart the initial setup, select “Initial Setup” in the “Hardware Setup” menu (➔ page 82).

After selecting the language for on-screen setup menus, a welcome screen is displayed.

Initial Setup

Welcome to initial setup. Have you connected all the speakers and devices? Before starting, please connect speakers and sources. Now, would you like to start initial setup?

1st Step : Audyssey MultEQ XT32: Auto Setup 2nd Step : Source Connection 3rd Step : Remote Mode Setup 4th Step : Network Connection

Yes No

Use q/w on the AV receiver or remote controller to

select one of the following options, and then press ENTER.

` Yes:

Continues to “Audyssey MultEQ XT32: Auto Setup”.

` No:

Skips the settings and terminates the initial setup. The setup wizard goes to “Terminating the Initial Setup” (➔ page 25). You can always restart the initial setup by selecting “Initial Setup” in the “Hardware Setup” menu (➔ page 82).

HOME

Exit

Audyssey MultEQ XT32: Auto Setup

This step performs the automatic speaker setup.

Use q/w to select one of the following options, and

then press ENTER.

` Do it Now:

The automatic speaker setup is performed following instructions on screen. Refer to step 2 of “Using the Automatic Speaker Setup” (➔ page 39). When this setting is complete, the setup wizard continues to “Source Connection”.

` Do it Later:

Skips this setting. Press ENTER and continue to “Source Connection”.

En-24

Turning On & Basic Operations

Source Connection

This step checks the connection of source components. With this step, you can enter remote control codes for the

Use q/w to select one of the following options, and

then press ENTER.

` Yes, Continue:

Performs the checkings.

` No, Skip:

Skips this step and continues to “Remote Mode

Setup”.

Select the input selector for which you want to

check the connection and press ENTER.

The picture of the corresponding source should appear on screen with a verification prompt.

When prompted, use q/w to select one of the

following options and then press ENTER.

` Yes:

Confirms that the source is properly displayed.

` No:

Displays an error report. Follow the troubleshooting instructions and recheck the source.

Use q/w to select one of the following options, and

then press ENTER.

` Yes:

Returns to step 2.

` No, Done Checking:

The setup wizard continues to “Remote Mode Setup”.

Remote Mode Setup

components you want to operate.

Use q/w to select one of the following options, and

then press ENTER.

` Yes:

Performs the remote control code input. Refer to step 5 of “Looking up for Remote Control Codes” (➔ page 90).

` No, Skip:

Skips this step and continues to “Network

Connection”.

When you’re finished, select one of the following

options and press ENTER.

` Yes, Done:

The setup wizard continues to “Network Connection”.

` No, not yet:

You can enter other remote control codes.

Network Connection

This step checks your network connection.

Use q/w to select one of the following options, and

then press ENTER.

` Yes:

Performs the checkings.

` No, Skip:

Skips this step and terminates the initial setup.

Follow the instructions on screen to perform the

network checking.

The checking is complete when the message “Successfully connected.” appears at the middle of the screen. Press ENTER to terminate the initial setup.

Tip

• If you have selected “Wireless (Option)”, you need to configure the optional wireless adapter. For further details, see the instruction manual provided with the wireless adapter (UWF-1).

If an error message appears, select one of the

following options and press ENTER.

` Retry:

Performs the checking again.

` No, Do it Later:

Skips this step and terminates the initial setup. The setup wizard goes to “Terminating the Initial Setup”.

Terminating the Initial Setup

This step ends the initial setup process.

Press ENTER.

To restart the initial setup, select “Initial Setup” in the “Hardware Setup” menu (➔ page 82).

En-25

Playback

The on-screen information appears only on a TV that is connected to HDMI outputs. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller, unless otherwise specified.

Playing the Connected Component

■ Operating with the remote controller

INPUT SELECTOR

RECEIVER VOL q/w

Listening mode buttons

Press RECEIVER followed by an INPUT

SELECTOR button.

Start playback on the source component.

Controlling Contents of USB or Network Devices

Press USB or NET first.

c d

e f

l m

n o

p q

TOP MENU

This button displays the top menu for each media or service.

q/w and ENTER

These buttons navigate through the menus.

e/r

This button cycles through pages.

PLAYLIST e/r

In Standard Mode (iPod/iPhone), this button selects playlists.

This button starts playback.

This button selects the beginning of the current song. Pressing this button twice selects the previous song.

This button fast-reverses the current song.

This button pauses playback.

You can toggle between the playback screen and the list screen during playback.

DISPLAY

This button switches between song information during playback. Press this button while the list screen is displayed to return to the playback screen.

ALBUM +/–

In Standard Mode (iPod/iPhone), this button selects albums.

This button displays the menu of Internet radio services.

RETURN

This button returns to the previous menu.

This button selects the next song.

This button fast-forwards the current song.

Turning On & Basic Operations

This button stops playback.

MODE

You can switch between Standard Mode and Extended Mode (iPod/iPhone).

RANDOM

This button performs random playback.

REPEAT

Press this button repeatedly to cycle through the repeat modes.

Tip

• See “Controlling Other Components” about the operation of

other components (➔ page 90).

Note

• The buttons you can use will differ depending on the devices and media used for playback.

En-27

Turning On & Basic Operations

Understanding Icons on the Display

This section describes icons that appear on the AV receiver’s display during media playback.

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Fast Reverse

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Playing an iPod/iPhone via USB

The on-screen information appears only on a TV that is connected to HDMI outputs.

This section explains how to play music/video files on the iPod/iPhone. Compatible iPod/iPhone models Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone

Press USB repeatedly to select the “USB(Front)”

input.

Tip

• The same operation can be done by selecting “USB” in the Home menu.

Connect the USB cable that comes with the

iPod/iPhone to the USB port on the front of the AV receiver.

While reading the contents of your iPod/iPhone, the message “Connecting...” appears on the AV receiver’s display.

The USB indicator lights. It will flash if the AV receiver cannot read the iPod/iPhone.

Tip

• When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

Press MODE repeatedly to switch to Extended

Mode (Music) or Extended Mode (Video).

A list of your iPod/iPhone model’s contents appears.

Tip

• If you want to operate using the iPod/iPhone or the remote

controller, press MODE repeatedly to switch to Standard mode.

• When you disconnect the iPod/iPhone, the AV receiver remembers the current mode. This means that if you disconnect when in Extended Mode (Music), the AV receiver will start in Extended Mode (Music) the next time you connect the iPod/iPhone.

Use q/w to select a folder, and then press ENTER to

open it.

Tip

• You can also use the q/w, enter (middle) and TUNING MODE buttons on the front panel. TUNING MODE allows

you to switch modes.

Use q/w to select a music/video file, and press

ENTER or 1 to start playback.

Note

• While the message “Connecting...” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

• If you connect an iPod or iPhone to the USB port, no sound will be output from the headphones jack.

En-28

Turning On & Basic Operations

Extended Mode (Music) Control

The music content information is displayed (lists are displayed), and you can control the music content while looking at the screen. Top screen list: Playlists, Artists, Albums, Genres, Songs, Composers, Shuffle Songs, Now Playing.

Note

• In this mode, video contents are not displayed, even if they are

input from the AUX INPUT VIDEO jack on the AV receiver’s front panel.

Extended Mode (Video) control

The video content information is displayed (lists are displayed), and you can control the video content while looking at the screen. Top screen list: Movies, Music Videos, TV Shows, Video Podcasts, Rentals.

Note

• To view the video contents of your iPod/iPhone, connect it to the

USB port and AUX INPUT VIDEO jack on the AV receiver’s front panel, using the official Apple Composite AV Cable.

• Depending on your iPod/iPhone model and generation, the displayed items may vary and the support for Extended Mode (Video) is not guaranteed.

Standard Mode Control

Playing a USB Device

The on-screen information appears only on a TV that is connected to HDMI outputs.

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players). See also:

• “Network/USB Features” (➔ page 114).

Press USB repeatedly to select the “USB(Front)” or

“USB(Rear)” input. Plug your USB device into the AV receiver’s USB

port.

The USB indicator lights. It will flash if the AV receiver cannot read the USB device.

Press ENTER.

A list of the device’s contents appears. To open a folder, use q/w to select it, and then press ENTER.

Use q/w to select a music file, and press ENTER or

1 to start playback.

Note

• While the message “Connecting...” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the USB port.

Listening to vTuner Internet Radio

You need to connect the AV receiver to your home network (➔ page 114). The on-screen information appears only on a TV that is connected to HDMI outputs.

The vTuner Internet Radio Service is a portal site featuring radio stations from all over the world.

You can search for stations by categories such as genre or location. The AV receiver is preinstalled with this service.

Press NET.

The network service screen appears, and the NET indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

Tip

• The same operation can be done by selecting “Network Service” in the Home menu.

Use q/w/e/r to select “vTuner Internet Radio”

and then press ENTER.

Use q/w to select a program and then press

ENTER.

Playback starts.

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller.

En-29

My Music

0 : 11 Great Artist My Favorite

Tip

• You can find stations similar to the one being played.

During playback, press MENU on the remote controller, select “Stations like this” and press ENTER.

Turning On & Basic Operations

■ Adding vTuner Internet Radio Stations to

Favorites

There are two ways you can register specific Internet radio stations (programs) from the vTuner Internet Radio.

Adding to My Favorites

The selected program will be added to “My Favorites” on the network service screen, which appears when pressing NET on the remote controller.

1. Press MENU with the station selected or while a

station is playing.

2. Use q/w to select “Add to My Favorites”, and press

ENTER.

3. Use q/w/e/r to select “OK”, and press ENTER.

Tip

• You can rename the stations saved in “My Favorites”.

Adding to vTuner Internet Radio’s Favorites

Select “vTuner Internet Radio” and press ENTER to display the “Favorites” folder that appears on the same screen as “Stations By Genre”, “Stations By Location”, etc. This is where your favorite Internet radio bookmarks will be stored.

To register your favorite stations using a personal computer, you need to connect your PC to the same network as the AV receiver. Enter the ID# (MAC address) of your unit on http://onkyo.vtuner.com/. You can then register your favorite radio programs. The ID# is shown at the bottom of the “vTuner Internet Radio” top menu, and the AV receiver’s MAC address is shown on “Network” of the Setup menu (➔ page 81).

Registering Other Internet Radio

You need to connect the AV receiver to your home network (➔ page 114). The on-screen information appears only on a TV that is connected to HDMI outputs.

Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the Internet radio station, you may not be able to listen to some stations.

To listen to other Internet radio stations, you must register your station in “My Favorites” of the network service screen, as described below.

Note

• Services available may vary depending on the region. See the separate instructions for more information.

Select “Network” on the Setup menu to verify your

IP address (➔ page 81).

Take a note of the IP address.

On your computer, start your web browser.

Enter the AV receiver’s IP address in the browser’s

Internet address (URL) field.

If you are using Internet Explorer the URL by selecting “Open...” on the “File” menu.

Information on the AV receiver is then shown on your Internet browser (Web Setup).

Click on the “My Favorites” tab, and enter the

Internet radio station’s name and URL.

, you can also enter

Click “Save” to save the Internet radio station.

The Internet radio station is then added to “My Favorites”. To play the registered station, press NET,

and then select “My Favorites” on the network service screen. A list of registered Internet radio stations appears. Select the one that you saved and press ENTER.

Tip

• If you want to add a new station directly from “My Favorites”,

select an empty slot in the list and press MENU. Then, select “Create New Station” and press ENTER. Pressing ENTER again will display the keyboard screen. Use that keyboard to enter the station’s name and URL respectively, and then press ENTER.

• If you want to delete a station saved in “My Favorites”, press

MENU with the station selected or while the station is playing. Then, use q/w to select “Delete from My Favorites” and press

ENTER. You can also delete stations from the Web Setup.

• If you want to rename a station, select the desired station and

press MENU. Then, use q/w to select “Rename this station” and press ENTER.

• You can save up to 40 Internet radio stations.

En-30

+ 134 hidden pages