Onkyo TX-NR1007, PR-SC5507, TXNR3007 User Manual

Firmware Update for the TX-NR1007/3007/5007

We are pleased to offer this firmware update for the best possible performance of your AV
Receiver.

The firmware update may fail if an external HDMI control signal is input during the update
procedure. Please be sure to turn off the HDMI control function (RIHD) on your A/V receiver
before starting the update.

How to turn off RIHD:

In the Main menu select "7. Hardware Setup", then "7-4. HDMI".
Set "HDMI Control" to OFF.

· Please read the update instructions carefully before beginning.

· The firmware update should take 30 to 40 minutes. Once the update begins, don't turn off the

power supply to the A/V receiver until it is time to restart it.

· Depending on the conditions of the network, a firmware update via a network may take more

than one hour or even fail to finish. If the update is not completed within two hours, turn off
the power supply by pushing the ON/STANDBY button and then try updating again from
the beginning.

· Updating the firmware and adjusting the settings will be done automatically, but may take

some time to complete. Please follow the procedures as instructed when you update. Note
that the update may fail, or cause problems for your A/V receiver, if you do any of the
following:

• Pull out the A/V receiver’s power cord;

• Interrupt the power supply to the A/V receiver (e.g. if the breaker is tripped or if there is an

electrical outage);

• Insert or remove the LAN cable from a device in your network when updating over a

network;

• Insert or remove a USB memory device from the A/V receiver when updating via USB;

• Operate components connected to the A/V receiver via HDMI, such as a TV or a recording

device.

If your A/V receiver is damaged for any of the reasons above, an Onkyo service center will
repair the unit for a fee.

Firmware Update for the TX-NR1007/3007/5007

A firmware update is now available through the Network connection on the TX-NR1007/3007
and 5007 as well as though the USB connection on the TX-NR3007/5007.

The 10/16/09 update addresses:

1. Improved Internet Radio operability

2. Improved picture quality for iPod/iPhone through UP-A1

The 11/19/09 update addresses (TX-NR3007 and 5007 only):

1. Improved display of Chinese menus

The 12/22/09 update will:

1. Improves the functionality of auto speaker setup in Bi-amp mode and when a passive

subwoofer is connected

2. Improves the operation stability just after power-on (Depending on the timing, no sound

comes out.)

3. Improves on screen display menus

The 2/24/10 update will:

1. Enhance S/N during 24bit/96kHz content playback from USB memory/DLNA server

2. Reduce speaker relay switching sound

The latest update includes all prior updates.
We hope you enjoy the improved functionality this update provides to your AV Receiver.

Firmware Update for the TX-NR1007/3007/5007

There are the following methods to update the firmware: via network and via USB storage.
Please choose either one that suits your condition. Before you start, carefully read the update
procedure.

To update the firmware, it will take 15 to 25 minutes for TX-NR1007 and 30 to 40 minutes for
TX-NR3007/5007.

Update via network

You need a wired Internet connection to update the firmware.
For the update procedure, please refer to “Updating the Firmware via Network” on page 2.

Update via USB storage (TX-NR3007 and 5007 only)

Please prepare a USB storage device such as a USB flash memory stick. You need at least 32
MB of available space to update the firmware.
For the update procedure, please refer to “Updating the Firmware via USB” on page 4.

Precautions on the USB storage device:

· The storage media in the USB card reader may not work.

· If the storage device has been partitioned, each section will be treated as an independent

device.

· If the USB mass storage device contains a lot of data, the AV receiver/controller may

take a while to read it.

· Operation with all USB mass storage devices including the ability to power them is not

guaranteed.

· Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a

USB mass storage device when that device is used

· with the AV receiver/controller. We recommend that you back up your important music

files beforehand.

· If you connect a USB hard disk drive to the USB port, we recommend that you use its

AC adapter to power it.

· USB hubs and USB devices with hub functions are not supported. Do not connect your

USB mass storage device via a USB hub.

· USB memory devices with security functions are not supported.