Seismic Restraint
Installation Guide
60-0022 Rev E
For 1-, 2-, 3-cell cabinets
This guide is CONFIDENTIAL and designed only for Omnicell Technical personnel and/or designated
representatives.
This guide and accompanying software and/or hardware described in it are protected under copyright laws and may
not be copied, wholly or in part, without the express written consent of Omnicell, Inc. The same proprietary and
copyright notices must be attached to any permitted copies as were attached to the original documents.
Omnicell, Inc.
1201 Charleston Road
Mountain View, CA 94043
(650) 251-6100
www.omnicell.com
Omnicell and the Omnicell design mark, OmniBuyer, OmniCenter, OmniRx, OmniSupplier, SafetyMed, SafetyPak,
SafetyStock, and Sure-Med are registered trademarks. Anesthesia TT, Anesthesia Workstation, Anywhere RN,
Executive Advisor, Flexbin, Medication Surveillance, OmniDispenser, OmniLinkRx, OmniScanner, OmniTrack,
Omni TT, Open Touch, OptiFlex, OptiFlex MobileTrack, Point-to-Point Medication Safety, SecureVault, See & Touch,
SinglePointe, TempCheck, Touch & Go, VSuite, and WorkflowRx are trademarks of Omnicell, Inc. in the United States
and internationally. All other trademarks and trade names are the property of their respective owners.
Copyright 1999-2010 Omnicell, Inc. All rights reserved.
Seismic Restraint Installation Guide/60-0022 Rev E © 2010 Omnicell, Inc.
Table of Contents
Seismic Restraint Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
The Seismic Restraint Kit for the Omnicell Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Anchors and Anchor Bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Installing Seismic Restraint Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Positioning the Brackets and Drilling the Holes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Installing the Brackets/Anchors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Fitting the Omnicell Cabinet onto the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Fax Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FB-1
iii
© 2010 Omnicell, Inc. Seismic Restraint Installation Guide/60-0022 Rev E
Seismic Restraint Installation Guide
Seismic Restraint Kit
This document provides a step by step interpretation of the technical specifications for installing
Seismic Restraint brackets on a 1-, 2-, and 3-cell cabinet.
The Omnicell Seismic Restraint kit contains the following parts.
Qty Description P/N
1 Kit, Seismic Restraint, Omnicell cabinet 2007 14-1124
1 Left Seismic Restraint Bracket 53-2021
1 Right Seismic Restraint Bracket 53-2022
2 Seismic Restraint Cap Bracket 53-2023
4 ½ - 13 x 2¼ Hex Bolt, Grade 8 94-6220
4 ½ SAE Flat Washer 94-6178
1 LABEL, CABINET, SEISMIC, CAPACITY 65-2033
1-1
Table 1-1.
Anchors/Anchor Bolts
It is the responsibility of the facility to acquire the specific anchor type required for each
installation.
Seismic Restraint Brackets
This document is divided into four sections that explain the processes that make up the overall
installation of Seismic Restraint Brackets:
Positioning the Brackets and Drilling the Holes
Mounting the Brackets
Fitting the Omnicell cabinet onto the Brackets
Note: The steps are sequential and should be performed in order.
Bracket Positioning
1. Locate the exact space the Omnicell cabinet will occupy permanently – take into account the
amount of space needed to house the Omnicell cabinet plus additional space to be able to
reach the switch at the rear of the PC Box.
2. Remove the two rear leveling feet from the Omnicell cabinet.
© 2010 Omnicell, Inc. Seismic Restraint Installation Guide/60-0022 Rev E
1-2 Seismic Restraint Installation Guide
Seismic Restraint Brackets
Caution: This procedure requires the Omnicell cabinet to be tilted and two people are needed to
ensure that no injuries occur, and that the Omnicell cabinet is not damaged.
a. Tilt the cabinet toward the front of the unit, one person pushing from the back and the
second stabilizing the unit.
b. Slide a riser block (at least four inches high) between the frame and the floor at the back of
the unit as shown in Figure 1-1.
Figure 1-1. Prop the cabinet with a block
c. While one person stabilizes the unit in the front, the second person unscrews the leveling
the feet as shown in Figure 1-2.
Figure 1-2. Unscrew the leveling feet
3. Remove the block and place the seismic brackets in their approximate locations.
The cabinet will need to be away from the wall an additional ½ inch during this step so that the
Note:
anchoring pins do not engage the frame.
Seismic Restraint Installation Guide/60-0022 Rev E © 2010 Omnicell, Inc.
Seismic Restraint Installation Guide 1-3
Seismic Restraint Brackets
4. Mark the position of the brackets on the floor as shown in Figure 1-3.
Figure 1-3. Mark the position of the brackets on the floor
5. Have a contractor drill eight holes in the exact locations marked.
It is the responsibility of the structural engineer of record to authorize any permanent changes (i.e., drill
Note:
holes) to the floor of the facility. Omnicell employees should never perform any procedures that involve
permanently modifying the facility’s structure.
Brackets/Anchors Installation
Note: If it is necessary to hammer the anchors, take care not to damage the threads.
1. Expand the anchor by tightening nut to the specified manufacturer’s specification.
Figure 1-4. Install the anchor/bracket
2. Move the cabinet onto the brackets.
3. Once positioned, ensure each bracket is away from the side of the cabinet by approximately 1/
16 inch.
Note: The casters may come in contact with the mounting bolts, making the cabinet difficult to move.
4. Transfer the locations of the dowel pins on the brackets to the cabinet and mount the caps with
½ inch bolts.
© 2010 Omnicell, Inc. Seismic Restraint Installation Guide/60-0022 Rev E
1-4 Seismic Restraint Installation Guide
Seismic Restraint Brackets
5. Using a hammer, mark the location of the pins on the cabinet as shown in Figure 5.
Figure 1-5. Mark the pin locations
6. Remove the cabinet from the brackets.
7. Using a hammer, center-punch the cabinet at the locations of the dowels to make drilling
easier, then drill four ½ inch diameter mounting holes (two in the front and two in that rear) in
the cabinet as shown in Figure 6 and Figure 7.
Figure 1-6. Center-punch the dowel locations (front)
Figure 1-7. Center-punch the dowel locations (rear)
Cabinet Fitting
1. Move the Omnicell cabinet onto the brackets and seat against the back surface of the brackets.
Seismic Restraint Installation Guide/60-0022 Rev E © 2010 Omnicell, Inc.
Seismic Restraint Installation Guide 1-5
Seismic Restraint Brackets
Ensure that the mounting pins on the back of both brackets align. If there are problems with alignment
Note:
loosen the mounting bolts and re-position the brackets.
2. Mount the caps onto the front of the cabinet with the ½ - 13 x 2¼ hex bolt.
Note: A ½ SAE flat washer may be needed to make the cap parallel with the front surface of the cabinet.
3. Attach cap while aligning the mounting pins on the cap, with the mounting holes on the front
of the cabinet.
Note: If there are problems with alignment, loosen the anchoring bolts and reposition the brackets.
4. Apply the contents capacity label in a visible location on the front or side of the cabinet.
© 2010 Omnicell, Inc. Seismic Restraint Installation Guide/60-0022 Rev E
1-6 Seismic Restraint Installation Guide
Seismic Restraint Brackets
Fax Order Form
TO: Omnicell.com
FAX : (650) 251-6266
Please complete the following information and fax to the number above:
Please send me _____ copies of drawing No. 62-0002, sheets 1 through 3.
DATE: ____________________________________
FROM: ____________________________________
ORGANIZATION: ____________________________________
ADDRESS: ____________________________________
____________________________________
CITY: ____________________________________
STATE, ZIP: ____________________________________
TEL #: ____________________________________
EMAIL: ____________________________________
FED EX Account #: ____________________________________
Type of FedEx Service
e.g. 2nd Day, Standard
Overnight, etc.: ____________________________________
If a Federal Express account number is not provided, the drawing will be sent via regular mail.
Note:
Seismic Restraint Installation Guide/60-0022 Rev E © 2010 Omnicell, Inc.
Documentation Feedback
This document is designed to provide relevant technical information to those responsible for the
implementation, service, and support of Omnicell products. The Documentation team needs your
input, so we can continue to improve our publications.
Sending Comments to the Technical Documentation Team
Did this document meet your needs? If so, please let us know what we’re doing right. If not, please
provide specific feedback. E-mail or fax your feedback as follows:
E-mail: Documentation Requests e-mail group at documentationrequests@omnicell.com (specify the
document title or PN).
Fax: Send this page, along with your feedback, to (650) 251-6266, attention: Documentation.
This document is designed to provide relevant technical information to Omnicell personnel
responsible for the implementation, service, and support of Omnicell Automation Systems.
Feedback Form
Name: E-mail:
Dept./Title: Phone:
Feed back:
© 2010 Omnicell, Inc. Seismic Restraint Installation Guide/60-0022 Rev E
Loading...