Omnicell AnesthesiaTT Service Guide

0 (0)

OmniTT/AnesthesiaTT

Installation and Service

Guide

67-2024 Rev D

This guide is CONFIDENTIAL and designed only for Omnicell Technical personnel and/or designated

representatives.

This guide and accompanying software and/or hardware described in it are protected under copyright laws and may

not be copied, wholly or in part, without the express written consent of Omnicell, Inc. The same proprietary and

Omnicell, Inc.

1201 Charleston Road

Mountain View, CA 94043

(650) 251-6100

www.omnicell.com

Omnicell and the Omnicell design mark, OmniBuyer, OmniCenter, OmniRx, OmniSupplier, SafetyMed, SafetyPak,

SafetyStock, and Sure-Med are registered trademarks. Anesthesia TT, Anesthesia Workstation, Anywhere RN,

Executive Advisor, Flexbin, Medication Surveillance, OmniDispenser, OmniLinkRx, OmniScanner, OmniTrack,

Omni TT, Open Touch, OptiFlex, OptiFlex MobileTrack, Point-to-Point Medication Safety, SecureVault, See & Touch,

SinglePointe, TempCheck, Touch & Go, VSuite, and WorkflowRx are trademarks of Omnicell, Inc. in the United States

and internationally. All other trademarks and trade names are the property of their respective owners

iii

Table of Contents

Electronics Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Remove the LCD Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Remove the LCD Bezel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Remove the LCD Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Remove the Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2

Remove the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Remove the Printer PC Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Remove the Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Remove the Elastomer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Replace the Elastomer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Replace the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

Remove the Electronics Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

Remove the PowerCom2 tray from the OmniRx/TT. . . . . . . . . . . . . . . . . . . . . . . 1-11

Install the PowerCom3 CT PC Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

Replace the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12

Frames and Wireways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Remove the Wireways. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Remove and Replace the Manual Override Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Remove the Manual Override Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

Replace the manual override cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6

Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Tools List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Matrix Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Configuring Bins in Unlit Matrix Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2

Configuring Bins in lit Matrix Drawers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Labelling Matrix Drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3

Installing a Drawer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4

Removing a Drawer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

Appendix A: Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IN-1

iv Table of Contents

Feedback Form. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FB-1

1-1

Electronics Tray

Introduction

This section will give detailed instructions on the proper way to replace specific parts within the

CT PC Sled, also known as the electronics tray. To complete any of these procedures, first ensure

that the sled has been unplugged from any power outlet.

Tools List

The following tools are required to install the Electronics Tray:



T8 Torx Driver



T10 Torx Driver



T15 Torx Driver



9/64” Allen wrench

Removal Procedure

LCD Screen

1. Perform a graceful shutdown of the electronics tray.

2. Remove the four outer screws that secure the LCD bezel to the cabinet.

Use a Torx T10 screwdriver.

Figure 1-1. Remove the Four Outer Screws

3. Remove the front bezel.

1-2 Electronics Tray

Removal Procedure

LCD Assembly

1. Tilt the LCD assembly forward and disconnect the cables from the back of the LCD assembly.

a. Disconnect the inverter to power cable.

b. Disconnect the flat panel cable.

2. Set the lid back down.

3. Remove the four inner screws at the back of the console lid.

Figure 1-2. Remove the Four Inner Screws

4. Remove the LCD assembly from the LCD housing.

Speaker

1. Perform a graceful shutdown of the electronics tray.

2. Open the console top.

3. Remove the speaker from the motherboard.

Figure 1-3. Disconnect the speaker From the motherboard

Note: Hold onto the front of the LCD screen while removing the screws so that the assembly does not fall.

Electronics Tray 1-3

Removal Procedure

4. Remove the two screws that hold the speaker in place.

Use a Torx T10 screwdriver.

Figure 1-4. Remove the two screws that secure the speaker

5. Disconnect the speaker from the console top.

Printer

1. Perform a graceful shutdown of the electronics tray.

2. Open the printer cover by pushing the black release mechanism toward the rear of the

machine and lifting the cover.

Figure 1-5. Open the Printer Cover

1-4 Electronics Tray

Removal Procedure

3. Remove the paper from the printer. Push the platen lever to the left to set it to the disengage

position.

Figure 1-6. Turn the Platen Lever to the Left and Remove the Paper

4. Remove the four screws (two on each side) that secure the printer assembly to the cover.

Figure 1-7. Remove the Screws Securing the Printer Assembly

5. Remove the printer assembly.

Electronics Tray 1-5

Removal Procedure

6. Remove the four screws that secure the lower assembly to the frame.

Figure 1-8. Remove the Screws that Secure the Lower Assembly

7. Disconnect the printer ribbon cable and the printer data cables from the printer PC board.

Figure 1-9. Remove the Printer Ribbon Cable and the Printer Data Cable

1-6 Electronics Tray

Removal Procedure

8. Remove the printer.

Figure 1-10. Remove the Printer

Printer PC Card

1. Remove the four screws that secure the PC card to the frame.

Figure 1-11. Remove the Screws that Secure the Printer PC Card

2. Lift the card off the frame slightly, then remove the printer ribbon cable.

Electronics Tray 1-7

Removal Procedure

Keyboard

1. Remove the 14 nuts that secure the keyboard cover to the tray.

Figure 1-12. Remove the nuts that secure the keyboard cover to the tray

2. Remove the keyboard cover.

Figure 1-13. Remove the keyboard cover

3. Remove the keyboard from the tray.

1-8 Electronics Tray

Replacement Procedure

Elastomer

1. Hold the keypad with the elastomer facing up and gently pull the elastomer up and off the

keyboard.

Figure 1-14. Pull the elastomer up and off the keyboard

Replacement Procedure

Elastomer

1. Gently place the new elastomer onto the keyboard and push the rubber tabs through the holes

on the keyboard.

2. Keeping the keypad upright, reach underneath the keyboard and gently pull the tabs until the

elastomer rests snugly on the keyboard.

3. Remove any bubble or ripples in the elastomer and then place the new keypad and elastomer

back into place on the tray.

Keyboard

1. Replace the keyboard cover.

2. Replace the screws that secure the keyboard cover to the tray.

Note: To prevent ripples in the elastomer, pull the tabs through going left to right, right to left, bottom to top

or top to bottom. Do not pull the tabs through in a random order or in a circular pattern.

Electronics Tray 1-9

Electronics Tray

1. Disconnect the LAN cable and the AUX cables from the rear of the TT cabinet.

Figure 1-15. Location and labels for LAN and AUX cable connections on CT PC Tray

2. Access the electronics tray.

+ 28 hidden pages