Olympus CV-180 User manual

Download

INSTRUCTIONS

EVIS EXERA II VIDEO SYSTEM CENTER

OLYMPUS CV-180

USA: CAUTION: Federal law restricts this device to sale by or on the order of a physician.

Contents

Labels and Symbols ..................................................................... 1

Important Information — Please Read Before Use.................... 2

Intended use ............................................................................................ 2

Instruction manual .................................................................................... 2

User qualifications .................................................................................... 4

Instrument compatibility ........................................................................... 4

Repair and modification ............................................................................ 5

Signal words ............................................................................................. 5

Dangers, warnings and cautions............................................................... 6

Cardiac applications.................................................................................. 10

Summary of Equipment Functions ............................................. 11

Chapter 1 Checking the Package Contents............................ 13

Chapter 2 Nomenclature and Functions................................. 14

2.1 Front panel...................................................................................... 14

2.2 Rear panel ...................................................................................... 18

2.3 Keyboard......................................................................................... 21

2.4 Side panels ..................................................................................... 26

2.5 Videoscope cable EXERA II (MAJ-1430)........................................ 26

2.6 Set-up of screen options ................................................................. 27

2.7 Monitor ............................................................................................ 28

2.8 Pointer............................................................................................. 32

Chapter 3 Inspection ................................................................ 33

3.1 Inspection of the power supply ....................................................... 34

3.2 Inspection of the examination light.................................................. 35

3.3 Inspection of the automatic brightness control function .................. 36

3.4 Inspection of the monitor display .................................................... 37

3.5 Inspection of the freeze function ..................................................... 38

3.6 Inspection of the release function ................................................... 38

3.7 Inspection of the PinP (picture in picture) function.......................... 38

3.8 Inspection of the orientation function .............................................. 38

3.9 Inspection of the special light observation function......................... 39

3.10 Inspection of the scope switches and foot switches ....................... 39

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Contents

3.11 Power OFF...................................................................................... 39

Chapter 4 Operation.................................................................. 41

4.1 Operation flow ................................................................................. 44

4.2 Connection of an endoscope .......................................................... 46

4.3 Turning the video system center ON............................................... 50

4.4 Recall of user preset data ............................................................... 51

4.5 White balance adjustment............................................................... 52

4.6 Patient data ..................................................................................... 57

4.7 Observation of the endoscopic image............................................. 59

4.8 Recording of the observation image ............................................... 59

4.9 Termination of the operation ........................................................... 60

Chapter 5 Functions.................................................................. 62

5.1 Front panel ...................................................................................... 62

Image source buttons............................................................................ 62

PinP (picture in picture) display ............................................................. 64

Image enhancement mode (ENH.)........................................................ 67

Iris mode................................................................................................ 69

White balance........................................................................................ 70

Brightness adjustment (Exposure) ........................................................ 71

STOP button and PC card indicator ...................................................... 75

PC card slot and eject button ................................................................ 76

RESET button ....................................................................................... 80

5.2 Keyboard......................................................................................... 81

Domepoint ............................................................................................. 81

Clearing characters from the screen (“F1”) ........................................... 82

System setup (“Shift” + “F1”)................................................................. 84

Scope information (“F2”) ....................................................................... 84

User preset (“Shift” + “F2”) .................................................................... 85

Cursor (“F3”).......................................................................................... 85

Patient data (“Shift” + F3)...................................................................... 86

Freeze mode (“F4”) ............................................................................... 86

Browse (“Shift” + “F4”)........................................................................... 87

Stopwatch (“F5”).................................................................................... 88

Automatic gain control (AGC) (“F6”)...................................................... 89

Contrast mode (“Shift” + “F6”) ............................................................... 90

Image zooming (“F7”)............................................................................ 91

Color bar (“Shift” + “F7”)........................................................................ 93

Image size (“F8”) ................................................................................... 94

Printer lock (“Shift” + “F8”)..................................................................... 95

Image enhancement (“F9”).................................................................... 96

White balance adjustment (“Shift” + “F9”) ............................................. 97

Color tone adjustment (“COLOR”)......................................................... 98

Freeze (“FREEZE”) ............................................................................... 99

Release (“RELEASE”)........................................................................... 101

Arrow pointer (“Shift” + arrow keys and domepoint).............................. 102

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Contents

Color mode (“Shift” + “Alt” + “1”, “2”, “3”, “4”)........................................ 104

Ending examination (“EXAM END”)...................................................... 105

5.3 Image recording and playback (PC card) ....................................... 106

Storage level of the PC card................................................................. 106

Recording the frozen image on a PC card............................................ 108

PC card menu....................................................................................... 110

Basic operation of the PC card menu................................................... 111

Formatting of the PC card..................................................................... 114

Playback images from the PC card ...................................................... 115

Deleting images from a PC card........................................................... 117

Deleting folder from PC card ................................................................ 118

Annotation of images............................................................................ 119

Playback image annotation................................................................... 122

Playback the images using the personal computer .............................. 124

Image files and folders.......................................................................... 125

5.4 Image recording and playback (other than PC card) ...................... 127

Image filing system ............................................................................... 127

Videocassette recorder (VCR).............................................................. 129

5.5 Printing images ............................................................................... 131

Video printer ......................................................................................... 131

5.6 Pre-entry of patient data ................................................................. 136

Basic operation in the patient menu ..................................................... 136

Entering new patient data..................................................................... 137

Displaying patient data ......................................................................... 140

Editing previously entered patient data................................................. 141

Deleting previously entered patient data .............................................. 142

Clearing all patient data previously entered.......................................... 143

Recording patient data into PC card..................................................... 144

Loading patient data from PC card....................................................... 146

5.7 Scope information ........................................................................... 148

Displaying and entering scope information ........................................... 149

5.8 Special light observation ................................................................. 151

NBI (narrow band imaging)................................................................... 151

Chapter 6 Fuse replacement.................................................... 153

Chapter 7 Care, Storage and Disposal.................................... 155

7.1 Care ................................................................................................ 155

7.2 Storage ........................................................................................... 156

7.3 Disposal .......................................................................................... 156

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

iii

Contents

Chapter 8 Installation and Connection.................................... 157

8.1 Installation work flow ....................................................................... 158

8.2 Installation of the equipment ........................................................... 159

8.3 Fitting of accessories ...................................................................... 162

8.4 Light source .................................................................................... 164

8.5 Monitor ............................................................................................ 170

8.6 Keyboard......................................................................................... 178

8.7 Videocassette recorder (VCR) ........................................................ 179

8.8 Video printer.................................................................................... 181

8.9 OLYMPUS flushing pump (OFP) .................................................... 183

8.10 Foot switch ...................................................................................... 184

8.11 Ultrasound center............................................................................ 185

8.12 Connection to the AC mains power supply ..................................... 189

Chapter 9 Function setup......................................................... 193

9.1 Turning power ON........................................................................... 193

9.2 System setup .................................................................................. 194

Basic operation of the system setup ..................................................... 194

System .................................................................................................. 197

Printer.................................................................................................... 201

Image filing system................................................................................ 205

Monitor .................................................................................................. 207

Videocassette recorder ......................................................................... 210

Saving the system setup ....................................................................... 212

Summary of settings.............................................................................. 213

9.3 User preset ..................................................................................... 215

Basic operation of the user preset......................................................... 215

Remote switch and foot switch (EXERA and VISERA)......................... 218

Release function.................................................................................... 222

Recording format for PC card................................................................ 223

Freeze function...................................................................................... 224

Image enhancement (normal observation)............................................ 225

Color mode............................................................................................ 227

Image size ............................................................................................. 228

Iris.......................................................................................................... 231

Iris speed............................................................................................... 234

Auto gain control (AGC) ........................................................................ 236

Contrast................................................................................................. 237

Exposure area ....................................................................................... 238

Electronic shutter................................................................................... 239

Patient data display ............................................................................... 240

Scope nickname.................................................................................... 241

Release index time................................................................................ 242

Indication of the special light observation.............................................. 243

Monitor orientation function ................................................................... 244

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Contents

PinP (picture in picture) function........................................................... 245

Special light observation....................................................................... 249

Image enhancement (NBI observation)................................................ 249

Saving the user preset.......................................................................... 250

Resetting the user preset data to the factory defaults .......................... 251

Deleting user preset data...................................................................... 252

Summary of settings............................................................................. 254

Chapter 10 Troubleshooting ...................................................... 257

10.1 Troubleshooting guide .................................................................... 257

10.2 Returning the video system center for repair .................................. 266

Appendix ....................................................................................... 267

System chart ............................................................................................ 267

Transportation, storage, and operation environment ................................ 274

Specifications ........................................................................................... 274

EMC information ....................................................................................... 280

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Contents

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Labels and Symbols

Safety-related labels and symbols are attached on the locations shown below. If

labels or symbols are missing or illegible, contact OLYMPUS.

Caution that only the exclusive cable can be connected.

Labels and Symbols

CSA/UL marking

Fuse rating

FUSES T5AL250V

Potential equalization terminal

Electric rating

The product name, rated voltage and frequency are shown.

EVIS EXERA II

VIDEO SYSTEM CENTER

MODEL OLYMPUS CV-180 INPUT 100-240V 50/60Hz 150VA

Serial number plate

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Manufacturer name

Important Information — Please Read Before Use

Intended use

This video system center has been designed to be used with OLYMPUS camera

heads, endoscopes, light sources, monitors, endo-therapy accessories and

other ancillary equipment for endoscopic diagnosis, treatment and video observation. Do not use this video system center for any purpose other than its

intended use.

Instruction manual

This instruction manual contains essential information on using this video

system center safely and effectively. Before use, thoroughly review this manual

and the manuals of all equipment which will be used during the procedure and use the equipment as instructed.

Keep this and all related instruction manuals in a safe, accessible location. If you

have any questions or comments about any information in this manual, please contact Olympus.

 Terms used in this manual

Light source:

The light source provides light and electrical signals to the endoscope. It also provides electrical signals to the video system center.

Video printer:

The video printer is a device that prints the frozen video image.

Wall mains outlet:

The wall mains outlet is a wall AC mains power outlet socket having the

exclusive terminal for grounding.

Isolation transformer:

The isolation transformer is a safety device that is used to isolate non-

insulated equipment with potentially high leakage currents to decrease the possibility of electric shock.

Image sensor (CCD):

Image sensor (CCD) is a device that converts light into electrical signals.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

Automatic brightness control:

The automatic brightness control automatically adjusts the intensity of the

light emitted from the light source so that the endoscopic image will be

maintained at constant brightness even if the distance between the distal end of the endoscope's insertion tube and the subject changes.

Color adjustment:

Color adjustment adjusts the color balance on the video monitor.

Iris:

The iris function is used to electrically measure the brightness of an

endoscopic image to obtain a control signal for the purpose of automatic

light adjustment.

Freeze:

The freeze function creates a stationary view of the moving image.

Release:

The release function is used to capture and record an endoscopic image.

Edge enhancement:

Edge enhancement is an image processing technique that electronically

sharpens the edges of an image.

Structure enhancement:

Structure enhancement is an image processing technique that electronically emphasizes the detailed patterns and edges of an image to

increase sharpness.

PinP (Picture in picture):

PinP function displays both the image of the endoscopic live image and

the image of an external device on the monitor simultaneously.

PC card:

A digital medium for storage of images, etc.

Wash out:

Wash out is the inability to see details in the endoscopic image due to excessive brightness.

HDTV:

High Definition Television. This is a format for high resolution video

transmission featuring higher definition than the standard SDTV format.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

SDTV:

Standard Definition Television. It is the format used in standard video

systems.

Special light observation:

This is a observation using filtered light.

NBI (narrow band imaging):

This is one of the special light observations using the narrow band

observation light.

User qualifications

If there is an official standard on user qualifications to perform endoscopy and

endoscopic treatment that is defined by the medical administration or other

official institutions, such as academic societies on endoscopy, follow that

standard. If there is no official qualification standard, the operator of this instrument must be a physician approved by the medical safety manager of the

hospital or person in charge of the department (department of internal medicine,

etc.).

The physician should be capable of safely performing the planned endoscopy

and endoscopic treatment following guidelines set by the academic societies on endoscopy, etc., and considering the difficulty of endoscopy and endoscopic

treatment. This manual does not explain or discuss endoscopic procedures.

Instrument compatibility

Refer to the “System chart” in the Appendix to confirm that this video system

center is compatible with the ancillary equipment being used. Using incompatible equipment can result in patient injury or equipment damage and makes it

impossible to obtain the expected functionality.

This instrument complies with the EMC standard for medical electrical equipment; edition 2 (IEC 60601-1-2: 2001). However, when connecting to an

instrument that complies with the EMC standard for medical electrical

equipment; edition 1 (IEC 60601-1-2: 1993), the whole system complies with edition 1.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Repair and modification

This video system center does not contain any user-serviceable parts. Do not

disassemble, modify or attempt to repair it; patient or operator injury, equipment

damage and/or the impossibility to obtain the expected functionality can result. Some problems that appear to be malfunctions may be correctable by referring

to Chapter 10, “Troubleshooting”. If the problem cannot be resolved using the

information in Chapter 10, contact Olympus. This instrument is to be repaired by Olympus technicians only.

Signal words

The following signal words are used throughout this manual:

Important Information — Please Read Before Use

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also

be used to alert against unsafe practices or potential

equipment damage.

Indicates additional helpful information.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

Dangers, warnings and cautions

Follow the dangers and cautions given below when handling this video system

center. This information is to be supplemented by the dangers and cautions

given in each chapter.

• Strictly observe the following precautions. Failure to do so

may place the patient and medical personnel in danger of

electric shock.

− When this video system center is used to examine a

patient, do not allow metal parts of the endoscope or its accessories to touch metal parts of other system

components. Such contact may cause unintended current

flow to the patient.

− Keep fluids away from all electrical equipment. If fluids are

spilled on or into the unit, stop operation of the video

system center immediately and contact Olympus.

− Do not prepare, inspect or use this video system center

with wet hands.

• Never install and operate the video system center in

locations where:

− the concentration of oxygen is high;

− oxidizing agents (such as nitrous oxide (N

in the atmosphere;

− flammable gases are present in the atmosphere;

− flammable liquids are near.

Otherwise, explosion or fire may result because this video

system center is not explosion-proof.

O)) are present

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

• In case of instrument failure or malfunction, always keep another video system center in the room ready for use.

• Never insert anything into the ventilation grills of the video

system center. It can cause an electric shock and/or fire.

• Although the illumination light emitted from the endoscope's

distal end is required for endoscopic observation and treatment, it may also cause alteration of living tissues such

as protein denaturation of liver tissue and perforation of the

intestines by inappropriate use.

Observe the following warnings on the illumination.

− Always set the minimum required brightness. The

brightness of the image on a video monitor may differ

from the actual brightness at the distal end of an

endoscope. Especially in combination with endoscopes using an electrical shutter function, pay attention to the

brightness level setting of the light source. When this

instrument is used with a light source compatible with automatic brightness control function, be sure to use this

function. The automatic brightness control function can

keep the illumination light properly. Refer to the instruction manual of the light source for details.

− Do not continue observation in the proximity to tissue or

keep the distal end of the endoscope in contact with living tissue for a long time. It may cause patient burns.

− When discontinuing the use of the endoscope, be sure to

turn the light source OFF so that the endoscope does not irradiate unnecessary light.

• This product may interfere with other medical electronic

equipment used in combination with it. Before use, refer to

the Appendix to confirm the compatibility of this instrument with all equipment to be used.

• Do not use this product in any place where it may be subject

to strong electromagnetic radiation (for example, in the

vicinity of a microwave therapeutic device, MRI, wireless set, short-wave therapeutic device, cellular/portable phone, etc.).

This may impair the performance of the product.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

• If the endoscopic image dims during use, blood, mucus or

• For reasons described below, do not rely on the NBI imaging

debris may adhere to the light guide on the distal end of the endoscope. Carefully withdraw the endoscope from the

patient and remove the blood or mucus in order to obtain

optimum illumination and to ensure the safety of the examination. If you continue to use the endoscope in such a

condition, the distal end temperature may rise and cause

mucosal burns. It may also cause patient and/or operator injury.

modality alone for primary detection of lesions or to make a

decision regarding any potential diagnostic or therapeutic intervention.

− It has not been demonstrated to increase the yield or

sensitivity of finding any specific mucosal lesion including

colonic polyps or Barrett’s esophagus.

− It has not been demonstrated to aid in differentiating establishing the presence or absence of dysplasia or

neoplastic changes within mucosa or mucosal lesions.

• To display observation images, connect the output terminal

of the video system center directly to the monitor. Do not make the connection via any ancillary equipment. Images

may disappear during observation depending on the

condition of ancillary equipment.

• Do not use a pointed or hard object to press the buttons on

the front panel and/or keyboard. This may damage the

buttons.

• Do not touch the electrical contacts inside the video system center's connectors.

• Do not apply excessive force to this video system center

and/or other instruments connected. Otherwise, damage

and/or malfunction can occur.

• Do not connect or disconnect the endoscope connector while this video system center is turned ON. Connecting or

disconnecting the endoscope while this video system center

is ON may destroy the CCD. Turn the video system center OFF before connecting or disconnecting the endoscope.

• Clean and vacuum dust the ventilation grills using a vacuum

cleaner, when necessary. Otherwise, the video system

center may break down and gets damaged from overheating.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Important Information — Please Read Before Use

• Be sure that this instrument is not used adjacent to or

stacked with other equipment (other than the components of

this instrument or system) to avoid electromagnetic

interference.

• Electromagnetic interference may occur to this instrument

when it is placed near equipment marked with the following

symbol or other portable and mobile RF communications

equipment such as cellular phones. If radio interference occurs, mitigation measures may be necessary, such as

reorienting or relocating this instrument or shielding the

location.

As defined by the international safety standard (IEC 60601-

1), medical electrical equipment is classified into the following types: TYPE CF applied part (the instrument can

safely be applied to any part of the body, including the heart),

and TYPE B/BF applied part (the instrument can safely be applied to any organ except the heart). The part of the body

that an endoscope or electrosurgical accessory can safely be

applied to depends on the classification of the equipment to which the instruments are connected. Before beginning the

procedure, check the current leakage classification type of

each instrument to be used for the procedure. Classification types are clearly specified in the instruments' instruction

manuals.

Symbol Classification

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

TYPE CF applied part

TYPE BF applied part

TYPE B applied part

Important Information — Please Read Before Use

Cardiac applications

• Use only the devices listed in the “System chart” in the

• For cardiac applications, never support the endoscope with a

• The use of medical devices not specifically designed for

Appendix for endoscopic observation or treatment of the

heart or areas near the heart. Other combinations of equipment may cause ventricular fibrillation or seriously

affect the cardiac function of the patient.

metal surgical arm which is not electrically isolated from the

ground. If not isolated, the endoscope will be connected to the ground through the surgical arm and bed, and will

conduct unexpected leakage current which may seriously

affect the cardiac function of the patient.

cardiac applications may cause ventricular fibrillation or

seriously affect the cardiac function of the patient. As

specified by the international standard IEC 60601-1, any applied part used for observation or treatment of the heart or

areas near the heart must meet “TYPE CF applied part”

requirements for low electrical leakage current. When using endoscopes for endoscopic cardiac applications, the applied

part requirements include all devices directly connected to

the endoscope, such as the light guide cable, camera head and telescope holder. Each of these devices must

individually meet the “TYPE CF applied part” requirements

for leakage current limits if they are to be used for cardiac applications.

The OLYMPUS light guide cables and camera heads listed in

the “System chart” in the Appendix (TYPE CF applied part)

which are suitable for cardiac applications bear a mark.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Summary of Equipment Functions

This instrument is a system controller of the endoscopic image observation

system that displays, records and prints the endoscopic images. Some of the functions of this instrument described below are enabled only when the required

equipment are connected to this instrument. For more details, refer to the

instruction manuals for this instrument and the other instruments connected.

Displaying the endoscopic images on the monitor

• The endoscopic live image and the other images of, for example, the ultrasonic endoscope connected to this instrument can be displayed on

the monitor.

• The endoscopic image and other external images can be displayed on

the same monitor at the same time (PinP function).

→ “PinP (picture in picture) display” on page 64

• Either a standard-definition (SDTV) monitor or high-definition (HDTV) monitor can be used.

Special light observation

Endoscopic observation using filtered light is available.

→ Section 5.8, “Special light observation” on page 151

Adjusting the endoscopic images

Images can be adjusted to enable clear and convenient observation.

• Adjustment of the image color

→ “Color tone adjustment (“COLOR”)” on page 98

• Adjustment of the image brightness

→ “Brightness adjustment (Exposure)” on page 71

• Changing the iris mode → “Iris mode” on page 69

• Changing the contrast mode

→ “Contrast mode (“Shift” + “F6”)” on page 90

• Enhancement of edge lines and patterns of the images

→ “Image enhancement mode (ENH.)” on page 67

• Changing the image size → “Image size (“F8”)” on page 94

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Summary of Equipment Functions

Entering patient data

Customizing the operations

Up to 20 remote switch settings and other functions such as iris mode, image

enhancement, etc., can be stored. → Section 9.3, “User preset” on page 215

• Enlargement of the images → “Image zooming (“F7”)” on page 91

• The patient data such as name, sex, etc. can be entered and displayed

on the monitor with the endoscopic live image.

→ Section 4.6, “Patient data” on page 57 and Section 5.6, “Pre-entry of patient data” on page 136.)

• Up to 40 sets of patients data can be stored on the PC card. These

patient data can be copied to the other CV-180.

→ “Recording patient data into PC card” on page 144

Recording images

• The endoscopic image can be recorded on the PC card.

→ Section 5.3, “Image recording and playback (PC card)” on page 106

• The endoscopic image can be recorded on the image-recording device

connected to this instrument, and the recorded images can be played back.

→ Section 5.4, “Image recording and playback (other than PC card)” on

page 127

• The endoscopic image can be printed from the printer connected to this instrument.

→ Section 5.5, “Printing images” on page 131

Operation of ancillary equipment

• Video casette recorder

→ “Videocassette recorder (VCR)” on page 129

• Video printer → Section 5.5, “Printing images” on page 131

• Image filing system

→ “Image filing system” on page 127

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 1 Checking the Package Contents

Chapter 1 Checking the Package

Contents

Match all items in the package with the components shown below. Inspect each item for damage. If the instrument is damaged, a component is missing or you

have any questions, do not use the instrument; immediately contact Olympus.

Video system center (CV-180)

Power cord

White cap (MH-155)

White cap set (MAJ-941)

Videoscope cable EXERA II (MAJ-1430)

White cap holder (MAJ-960)

Keyboard (MAJ-1428)

HDTV/SDTV monitor cable (MAJ-1462)

Foot holder (MAJ-1433, 4 pcs.)

Water container (MAJ-901)

Spare fuse (MAJ-1432, 2 pcs.)

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Scope cable holder (MAJ-1466)

Instruction manual

Cable color sheet

Keyboard cover (MAJ-1557)

Chapter 2 Nomenclature and Functions

2.1 Front panel

12. Exposure level (EXPOSURE) indicator

11. Exposure adjustment

4. Locking lever

(EXPOSURE) buttons

10. NBI indicator

3. Video connector socket

2. Power indicator

1. Power switch

22. RESET button

9. HDTV indicator

8. White balance (Wh/B OK) indicator

7. White balance (Wh/B) button

6. Picture in picture (PinP) button

5. Image source buttons

21. Image enhancement mode indicators

20. Image enhancement mode (ENH.) button

19. Iris mode indicators

18. Iris mode (IRIS) button

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

17. STOP button

16. PC card status indicator

15. Eject button

14. PC card slot

13. PinP composite terminal

Chapter 2 Nomenclature and Functions

1. Power switch

Press to turn the video system center ON or OFF.

2. Power indicator

Lights up when the video system center is ON.

3. Video connector socket

The video plug of the videoscope cable, videoscope or camera head are

connected to this socket.

4. Locking lever

Press down to disconnect the video plug of the videoscope cable,

videoscope or camera head.

5. Image source buttons

Press these buttons to select the image sources to be displayed on the

monitor. Press and hold the buttons to change (except “SCOPE”).

→ “Image source buttons” on page 62

Button The image on the monitor

SCOPE The endoscopic live image

DV/VCR The image of the videocassette recorder, etc.

PC The image of the image filing system

PRINTER The image of the video printer

6. Picture in picture (PinP) button

Press to display an image of the connected ancillary equipment and the

endoscopic live image together on the monitor.

• Setting of the PinP function → “PinP (picture in picture) function” on page 245

• Operation of the PinP function

→ “PinP (picture in picture) display” on page 64

7. White balance (Wh/B) button

Press to perform the white balance adjustment. → Section 4.5, “White balance adjustment” on page 52

8. White balance (Wh/B OK) indicator

The indicator lights up when the white balance adjustment is completed.

9. HDTV indicator

Lights up green when the instrument is turned ON, and turns white when the

HDTV compatible endoscope is connected to this instrument.

10. NBI indicator

Lights up green when the NBI compatible endoscope is connected to this

instrument, and turns white during NBI observation. This indicator works only when the light source CLV-180 is used.

→ “NBI (narrow band imaging)” on page 151

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

11. Exposure adjustment (EXPOSURE) buttons

Press to adjust the brightness of the observation light. When CLV-180 is

used, this button is interlocked with the “BRIGHTNESS” on CLV-180.

→ “Brightness adjustment (Exposure)” on page 71

12. Exposure level (EXPOSURE) indicator

Indicates the brightness level of the observation light.

→ “Brightness adjustment (Exposure)” on page 71

13. PinP composite terminal

The ultrasound center (EUS), endoscope position detecting unit (UPD) etc.

can be connected to this connector to input the images to be displayed together with the endoscopic observation image. The PinP function can also

be used with the PinP Y/C terminal on the rear panel. However, the PinP

composite terminal takes priority over the PinP Y/C terminal.

14. PC card slot

Insert the PC card adapter (optional) in this slot. The xD picture card can be

used as the storage media.

→ “PC card slot and eject button” on page 76

15. Eject button

Press to remove the PC card from the PC card slot.

→ “PC card slot and eject button” on page 76

16. PC card status indicator

This indicator lights up green when the PC card is inserted into the PC card

slot, and blinks orange while accessing the PC card. → “PC card slot and eject button” on page 76

17. STOP button

Press to stop accessing the PC card. Be sure to press this button before removing the PC card from the PC card slot.

→ “PC card slot and eject button” on page 76

18. Iris mode (IRIS) button

Press to switch the iris mode (brightness adjustment method) of the

endoscopic image. Either “AUTO” or “PEAK” mode can be selected.

• Presetting

→ “Iris” on page 231

• Switching operation →“Iris mode” on page 69

19. Iris mode indicators

Indicates the iris mode being selected.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

20. Image enhancement mode (ENH.) button

“Image enhancement” refers to facilitate observation of edges and patterns

of the endoscopic image by electronic treatment. Press this button to

change the modes of the enhancement methods.

•Presetting

→ “Image enhancement (normal observation)” on page 225

or “Image enhancement (NBI observation)” on page 249

•Operation

→ “Image enhancement mode (ENH.)” on page 67

21. Image enhancement mode indicators

One of these indicators light up and indicates the image enhancement mode

being selected. The indicator goes off when the image enhancement is not

used.

22. RESET button

Press and hold the switch to return the settings changed during operation to

the default settings.

→ “RESET button” on page 80

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

2.2 Rear panel

8. PC remote terminal

7. PC IN terminal

6. PC OUT terminal

5. Printer remote terminal

4. Printer OUT terminal

3. Printer IN terminal

2. Y/C OUT terminal

1. Keyboard terminal

9. Remote terminal

10. Option terminal

11. Foot switch terminal

12. VCR remote terminal

13. Fuse box

14. AC power inlet

24. Potential equalization terminal

23. Monitor OUT terminal

22. Composite OUT terminal

21. Monitor remote terminal

20. PC OUT2 terminal

15. Light control terminal

16. Light source terminal

17. PinP Y/C terminal

18. HD/SD SDI OUT terminal

19. Digital OUT terminal

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

1. Keyboard terminal

Connect the keyboard.

2. Y/C OUT terminal

Outputs a Y/C video signals.

3. Printer IN terminal

Connect the video printer. Inputs the analog video signal from the video

printer.

4. Printer OUT terminal

Connect the video printer. Outputs the analog video signal to the video

printer.

5. Printer remote terminal

Connect the video printer. Establishes communication with the video printer.

6. PC OUT terminal

Connect the image filing system. Outputs the analog video signal to the image filing system.

7. PC IN terminal

Connect the image filing system. Inputs the analog video signal from the

image filing system.

8. PC remote terminal

Connect the image filing system. Establishes communication with the image

filing system.

9. Remote terminal

Outputs the signal synchronizing the release and VCR (Rec/Pause)

operation.

10. Option terminal

Reserved for future system expansion.

11. Foot switch terminal

Connect the foot switch.

12. VCR remote terminal

Connect an Olympus-recommended VCR. Outputs the analog video signal and the remote signals to the VCR.

13. Fuse box

Stores the fuses that protect the instrument from electrical surges.

14. AC power inlet

Connect the provided power cord to supply the AC power via this inlet.

15. Light control terminal

Connect a light source that supports the analog interface.

16. Light source terminal

Connect a light source CLV-180 that supports the digital interface.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

17. PinP Y/C terminal

The ultrasound center (EUS), endoscope position detecting unit (UPD) etc.

can be connected to this connector to input the image to be displayed

together with the endoscopic observation image. The PinP function can also be used with the PinP composite terminal on the front panel. However, the

PinP composite terminal takes priority over the PinP Y/C terminal.

18. HD/SD SDI OUT terminal

Connect a monitor compatible with the serial digital interface (SDI). Outputs

the SDI signal.

19. Digital OUT terminal

Connect an Olympus-recommended digital video recorder to output and

input the digital video signal to the digital video recorder, using IEEE1394

cable.

20. PC OUT2 terminal

Connect the image filing system. Outputs an SDI signal to the image filing

system.

21. Monitor remote terminal

Connect the monitor. Outputs the monitor control signal to the monitor.

22. Composite OUT terminal

Outputs the composite video signal.

23. Monitor OUT terminal

Connect the monitor. Outputs analog video signals to the monitor. HDTV

signal is output when the HDTV compatible endoscope is connected. This connector can output a 180° rotated image (see “Monitor orientation

function” on page 244).

24. Potential equalization terminal

This terminal is connected to a potential equalization terminal of the other

equipment connected to this instrument. The electric potential of their

equipment are made equal.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

2.3 Keyboard

Chapter 2 Nomenclature and Functions

20. PRINT QTY. key

19. PRINT key

18. DEL IMAGE key

17. CAPTURE key

16. #PER PAGE key

4. F4 key

3. F3 key

2. F2 key

1. F1 key

8. F8 key

7. F7 key

6. F6 key

5. F5 key

24. EXAM END key

23. RELEASE key

22. FREEZE key

21. COLOR key

12. F12 key

11. F11 ke y

10. F10 key

9. F9 key

26. Domepoint

25. Click key

15. Pause key

14. Scroll lock key

13. Print screen key

27. Arrow keys

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

1. F1 key

Press to clear or re-display the patient data on the monitor step by step. → “Clearing characters from the screen (“F1”)” on page 82

Press together with the “Shift” key to display the system setup menu to set

the basic functions of this instrument. → “System setup (“Shift” + “F1”)” on page 84

2. F2 key

Press to display the scope information window when using an endoscope with the endoscope information memory function. While the window is still

open, press this key again to display the scope information menu that shows

the information about the connected endoscope. → “Scope information (“F2”)” on page 84

Press together with the “Shift” key to display the user preset menu to set

and call up the observation condition of the endoscopic image. → See “User preset (“Shift” + “F2”)” on page 85

3. F3 key

Press to switch the display of the cursor on screen ON and OFF.

→ “Cursor (“F3”)” on page 85 Press together with the “Shift” key to display the patient data menu to enter

or call up the patient data onto the monitor.

→ “Patient data (“Shift” + F3)” on page 86

4. F4 key

Press to change the freeze mode.

→ “Freeze mode (“F4”)” on page 86 Press together with the “Shift” key to display the PC card menu to store or

call up the image data or the patient data from the PC card.

→ “Browse (“Shift” + “F4”)” on page 87

5. F5 key

Press to change the clock on the monitor to a stopwatch, and to start time

counting. → “Stopwatch (“F5”)” on page 88

6. F6 key

Press to switch the auto gain control (AGC) function ON and OFF. → “Automatic gain control (AGC) (“F6”)” on page 89

Press together with the “Shift” key to switch between the three steps of the

observation image contrast. → “Contrast mode (“Shift” + “F6”)” on page 90

7. F7 key

Press to change the zoom ratio of the observation image in three steps (x1; x1.2; x1.5).

→ “Image zooming (“F7”)” on page 91

Press together with the “Shift” key to display the color bar for checking the color of the monitor.

→ “Color bar (“Shift” + “F7”)” on page 93

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

8. F8 key

Press to change the image area size on the monitor.

→ “Image size (“F8”)” on page 94

Press together with the “Shift” key to disable the functions of the following 5 keys for video printer operation: #PER Page, CAPTURE, DEL IMAGE,

PRINT, PRINT QTY.

→ “Printer lock (“Shift” + “F8”)” on page 95

9. F9 key

Press to switch the image enhancement mode.

→ “Image enhancement (“F9”)” on page 96 Press together with the “Shift” key to perform the white balance adjustment.

→ “White balance adjustment (“Shift” + “F9”)” on page 97

10. F10 key

Press to stop ( ) the VCR.

→ “Videocassette recorder (VCR)” on page 129

11. F11 key

Press to pause ( ) the VCR. Press the Scroll ( ) key to resume play.

→ “Videocassette recorder (VCR)” on page 129

12. F12 key

Press to start ( ) VCR recording.

→ “Videocassette recorder (VCR)” on page 129

13. Print screen key

Press to fast-rewind ( ) the VCR.

→ “Videocassette recorder (VCR)” on page 129

14. Scroll lock key

Press to playback ( ) the VCR.

→ “Videocassette recorder (VCR)” on page 129

15. Pause key

Press to fast-forward ( ) the VCR.

→ “Videocassette recorder (VCR)” on page 129

16. #PER PAGE key

Press to set the number of images per video print sheet. The indicator

corresponding to the number lights up. An arbitrary number “N” on the

keyboard depends on the printer. → Section 5.5, “Printing images” on page 131

17. CAPTURE key

Press to capture the image in the video printer. → Section 5.5, “Printing images” on page 131

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

18. DEL IMAGE key

Press to set the printer cursor back on the print sheet by one. Press together

with the “Shift” key to delete a captured image at the position of the cursor.

→ Section 5.5, “Printing images” on page 131

19. PRINT key

Press to print the images captured in the video printer.

→ Section 5.5, “Printing images” on page 131

20. PRINT QTY. key

Press to specify the number of video print sheets to print simultaneously.

The indicator corresponding to the number lights up. An arbitrary number “N” on the keyboard can be specified in the system setup menu.

→ Section 5.5, “Printing images” on page 131

21. COLOR key

Press to select R (Red), B (Blue) or C (Chroma) to adjust the color of the

endoscopic image. The lamp corresponding to the selected tone above the

key lights up. Adjust the selected color tone using the “right” or “left” arrow

keys. The indicator on the right side of the “COLOR” key shows the adjustment status.

→ “Color tone adjustment (“COLOR”)” on page 98

22. FREEZE key

Press to freeze the live endoscopic image. Press the key again to return to

the live image.

→ “Freeze (“FREEZE”)” on page 99

23. RELEASE key

Press to record the image into the video printer, image filing system and PC

card. The recording devices to operate should be set in advance. → “Release (“RELEASE”)” on page 101

24. EXAM END key

Press to execute the examination end processing. → “Ending examination (“EXAM END”)” on page 105

25. Click key

Press this key to enter an item after selecting the item using the domepoint. → “Domepoint” on page 81

26. Domepoint

Moves the arrow pointer. Selects an item in the menu or puts a marking in the endoscopic image.

→ “Domepoint” on page 81

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

27. Arrow keys

Moves the cursor.

Press one of these keys together with the “Shift” key to display the arrow

pointer on the endoscopic image. → “Arrow pointer (“Shift” + arrow keys and domepoint)” on page 102

28. Other keyboard keys

•Esc

Cancels the selection or returns to the previous screen.

•Tab Goes to the next input area, or returns to the previous input area.

• Enter

Fixes entry and goes to the next text box or screen.

• Shift, Alt

Executes functions together with other keys.

• Back space

Clears the character left of the cursor.

•Delete Clears the character right of the cursor.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

2.4 Side panels

Ventilation grills

Front side

Rear side

2.5 Videoscope cable EXERA II (MAJ-1430)

“UP” mark

Connect to the video system center “UP” side up.

Video plug Scope side connector

Connect to the video connector socket of the video system center.

Connect to the scope connector of the endoscope.

Ventilation grills

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

2.6 Set-up of screen options

The software of this instrument has the following functions.

• The screen of the endoscopic live image and the images of the external instruments connected to this instrument

This is the basic screen of the instrument. This instrument starts the

endoscopic live image when it is turned ON.

→ Section 3.4, “Inspection of the monitor display” on page 37

• System setup screen

This screen is used for setting the basic functions to operate this instrument and the other instruments connected to it correctly.

→ Section 9.2, “System setup” on page 194

• User preset screen

Up to 20 user presets are available to save individual user settings. The

factory default settings are set before shipment.

→ Section 9.3, “User preset” on page 215

Chapter 2 Nomenclature and Functions

• Patient data screen

Patient name, sex, age, etc. can be entered for up to 40 patients in advance. Existing patient data can be accessed and displayed on the monitor together

with the endoscopic image, and can be stored on the PC card.

→ Section 5.6, “Pre-entry of patient data” on page 136

• PC card menu screen

This screen is used to browse endoscopic images on the PC card. → “PC card menu” on page 110

• Scope information screen

This screen is used to display and/or enter endoscope information such as

the type of endoscope, etc.

→ Section 5.7, “Scope information” on page 148

• Color bar screen

This screen is used to check the display color. → “Color bar (“Shift” + “F7”)” on page 93

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

2.7 Monitor

Endoscopic image display

1. Patient data

2. System clock

3. Image recording device display

4. Image information

5. Flushing pump

6. PC card capacity

7. Index image

8. Attending physician

9. Comments

10. Special light observation display

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:

John Smith Cardiac end of the stomach

NBI

11. Endoscopic image

12. Arrow pointer

R V

13. Orientation

14. Scope nickname

1. Patient data

Patient data such as name sex, etc. can be entered and displayed in this

area. → Section 4.6, “Patient data” on page 57

2. System clock

Date and time are displayed. The date format can be set. → “Date and time” on page 197

The clock has the stopwatch function.

→ “Stopwatch (“F5”)” on page 88

3. Image recording device display

The status of the image recording devices that record and print the image

are displayed only when the recording devices are activated.

Indication Device Details

CVP Video printer page 131

D.F Digital filing system page 127

VCR Videocassette recorder page 129

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

4. Image information

Displays image information on the monitor. The indications are displayed

only when these function are operated.

Indication Meaning Details

Ct Contrast page 90

Eh Enhancement mode page 67

Z Zoom ratio page 91

5. Flushing pump

Displayed only when the Olympus flushing pump (OFP) is processing.

6. PC card capacity

Indicates the remaining memory level of the PC card when the PC card is

inserted in the PC card slot. → “Storage level of the PC card” on page 106

7. Index image

Displays the reference image of the image taken by “RELEASE”.

→ “Release index time” on page 242

8. Attending physician

The physician’s name can be entered and displayed together with the

patient data.

9. Comments

Comments can be entered and displayed together with the patient data.

10. Special light observation display

Indicates the name of the special observation function during the

observation.

→ Section 5.8, “Special light observation” on page 151

11. Endoscopic image

The live endoscopic image is displayed in this area. The size and shape of

the image depends on the type of endoscope used. → “Image size” on page 228

12. Arrow pointer

The arrow pointer is used for pointing out a part of the endoscopic image and for entering data in the menus.

• Displaying

→ “Arrow pointer (“Shift” + arrow keys and domepoint)” on

page 102

•Operation → “Domepoint” on page 81

13. Orientation

“R” mark appears when a 180° reverse image is displayed.

→ “Monitor orientation function” on page 244

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

14. Scope nickname

The scope nickname is displayed when an endoscope with a scope

nickname function is connected.

→ “Scope nickname” on page 241

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Data input menu

Function button

Saves data, terminates the menu, etc.

Menu name

Text box

For entering and displaying data.

Highlight

Indicates in blue that the function button is selected.

Cursor

Used for entering data.

Chapter 2 Nomenclature and Functions

CLV CLV-S CLE

List box

Opens the pull down menu and selects the setting values.

Pull down menu

Click “ ” to show the setting values in the pull down menu.

Scroll bar

Shows all setting values not being displayed in the list box.

Arrow pointer

Moves the cursor, selects the function buttons, displays the pull down menus.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 2 Nomenclature and Functions

2.8 Pointer

Highlight, cursor and arrow pointer are available as pointing devices for the

endoscopic image and menus on the monitor.

Pointer Function Screen Displaying and operation

Highlight Indicates the button

selected.

• System setup menu

• User preset menu

• Patient data menu

• Scope information menu

• PC card information

Always displayed.

Movable by pressing the arrow, “Tab”,

or “Shift” + “Tab” keys.

Cursor Indicates the position to

enter data.

Arrow pointer Moves the cursor and

focus or points out a

specific portion of the

image.

• System setup menu

• User preset menu

• Patient data menu

• Scope information menu

• PC card information

• Endoscopic image

screen

• System setup menu

• User preset menu

• Patient data menu

• Scope information menu

• PC card menu Always displayed on image screen

• Endoscopic image

screen

Always displayed.

Movable by pressing the arrow,

“Home”, or “End” keys.

Always displayed.

Movable by the domepoint.

(unless full image screen selected).

Press “Shift” and any arrow key in the

full image screen to display/remove the

arrow pointer.

Press “Shift” and any arrow key.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

• Review Chapter 8, “Installation and Connection” thoroughly,

and prepare the instruments properly before inspection. If the equipment is not properly prepared before each use,

equipment damage, patient and operator injury and/or fire

can occur.

• Before each procedure, inspect the video system center as

instructed below. Inspect other equipment to be used with this video system center as instructed in their respective

instruction manuals. Should any irregularity be observed, do

not use the video system center and see Chapter 10, “Troubleshooting”. If the irregularity is still observed after

consulting Chapter 10, contact Olympus. Damage or

irregularity may compromise patient or user safety and may result in more severe equipment damage.

Chapter 3 Inspection

Prepare the video system center and other ancillary equipment before each particular case. Refer to the respective instruction manual for each piece of

equipment.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

3.1 Inspection of the power supply

1. Confirm that the videoscope cable, camera head and/or endoscope is

connected to the videoscope cable socket of the instrument.

For the connection of the endoscope or scope cable, refer to

Section 4.2, “Connection of an endoscope” on page 46.

2. Press the power switch of the instrument (see Figure 3.1). The indicator

lamp above the power switch lights up.

Power indicator

Power switch

Video connector socket

Figure 3.1

 If the power fails to come ON

When the power fails to come ON, turn the video system center OFF. Then

check the video system center referring to Chapter 10, “Troubleshooting”. If the

power still fails to come ON, contact Olympus.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

3.2 Inspection of the examination light

Do not stare directly into the light beam. This may result in

eye injury.

Turn ON the light source and confirm that examination light is emitted from the

distal end of the endoscope (see Figure 3.2). For operation of the light source,

refer to its instruction manual.

Endoscope’s distal end

Examination light

Chapter 3 Inspection

Figure 3.2

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

3.3 Inspection of the automatic brightness control function

1. Confirm that this instrument is connected to the light source using the light

source cable or light control cable (see Section 8.4, “Light source” on

page 164).

2. According to the directions given in the light source's instruction manual,

confirm that the light source's brightness control is set to “AUTO” and that

the brightness level is in the center of the adjustable range.

3. Move the distal end of the endoscope between 1 and 3 cm from your palm.

Confirm that the brightness of the image on the monitor remains constant.

Confirm that the light emitted from the distal end of the endoscope changes in your palm.

4. Hold the distal end of the endoscope 3 cm from your palm. Use a piece of

gauze, etc. to prevent the endoscope's distal end and your palm from being

exposed to extraneous light. View the image on the monitor.

5. Confirm that the brightness of the image on the monitor changes when the

light source's brightness level is changed.

• In combination with some endoscope models, the space between the distal end of the endoscope and your palm in

which the automatic brightness control function is available

will be smaller than 1 - 3 cm. Please refer to the instruction manual of the endoscope used.

• Depending on the light source connected, the exposure level

indicator on the video system center goes off. Control the

brightness on the light source referring to “Brightness adjustment (Exposure)” on page 71.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

3.4 Inspection of the monitor display

Be sure to perform white balance adjustment before

inspecting the color on the monitor display. See Section 4.5,

“White balance adjustment” on page 52.

1. Turn the instrument ON. Then the endoscopic image appears on the screen

(see Figure 3.3).

ID:

Name: Sex: Age: D.O.B. 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

Chapter 3 Inspection

Physician: Comment:

Figure 3.3

2. Confirm that the endoscopic image is normal by observing any object such

as the palm of your hand.

3. Confirm that the date and time are correct.

4. Confirm that the “CVP” counter and “D.F” counter are displayed on the

screen when the video printer and digital filing system are connected.

5. Confirm that enough space is available on the PC card to store endoscopic

images.

• The display layout is variable according to the connected

endoscope and user preset.

• For setting the date or time, refer to “Date and time” on

page 197.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

3.5 Inspection of the freeze function

Do not use this instrument when the live image cannot be

observed. Otherwise, patient injury may occur.

1. Press the “FREEZE” key on the keyboard, and confirm that the live

endoscopic image freezes and a short beep is heard.

2. Press the “FREEZE” key again and confirm that the frozen image returns to

the live image.

3. Confirm the function of the scope switches and/or foot switches, when the

freeze function is assigned to these switches.

3.6 Inspection of the release function

1. Press the “RELEASE” key on the keyboard.

2. Confirm that the live image freezes for a short time and a beep is heard.

3. Confirm that the selected recording device is activated.

4. Confirm that the counter for the recording devices, which are displayed on

the monitor, increments by one.

5. Confirm the function of the scope switches and/or foot switches, when the

release function is assigned to these switches.

3.7 Inspection of the PinP (picture in picture) function

According to the “PinP (picture in picture) display” on page 64, confirm that the PinP indication can be performed correctly.

3.8 Inspection of the orientation function

If the orientation function is activated, confirm that the indication on the monitor

is an endoscopic image rotated by 180° (refer to “Monitor orientation function” on

page 244).

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

3.9 Inspection of the special light observation function

According to Section 5.8, “Special light observation” on page 151, confirm that the image of the special light observation can be displayed correctly.

3.10 Inspection of the scope switches and foot switches

If any function is assigned to the scope's remote switches and/or foot switches, confirm the proper function of these switches.

3.11 Power OFF

Press the power switch of the instrument (see Figure 3.1) to turn the instrument OFF. The indicator above the switch goes off.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 3 Inspection

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

This chapter explains the work flow of endoscopic observation using the video

system center. For information on how to use the functions that are not explained in this chapter, refer to the reference pages.

The operator of the video system center must be a physician or medical personnel under the supervision of a physician and must have received sufficient

training in clinical endoscopic techniques. This manual, therefore, does not

explain or discuss clinical endoscopic procedures. It only describes basic operation and precautions related to the operation of the video system center.

• Be sure to wear protective equipment such as eye wear, face

mask, moisture-resistant clothing and chemical-resistant

gloves that fit properly and are long enough so that your skin is not exposed. Otherwise, dangerous chemicals and/or

potentially infectious material such as blood and/or mucus of

the patient may cause an infection.

Chapter 4 Operation

• Should any irregularity is observed, do not use the video system center. Damage or irregularity may compromise

patient or user safety and may result in more severe

equipment damage.

• Anytime you observe an abnormality in a video system center function, stop the examination immediately and take

action according to the following procedures. Using a

defective video system center may cause patient and/or operator injury.

− If the endoscopic image disappears or if the image

freezes and cannot be restored, press the “RESET”

button or temporarily turn the video system center OFF and wait for about 10 seconds. Then turn it back ON

again.

For ancillary equipment used in conjunction with the video system center, also turn the power OFF and then ON

again as directed in their respective instruction manuals. If

this fails to correct the problem, immediately stop using the equipment and turn the video system center and light

source OFF. Then, gently withdraw the endoscope from

the patient as described in the endoscope's instruction manual.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

− If any other abnormality occurs or is suspected, immediately stop using the equipment, turn OFF all

equipment, and gently withdraw the endoscope from the

patient as described in the endoscope's instruction manual. Then refer to the instructions in Chapter 10,

“Troubleshooting”. If the problems cannot be resolved by

the remedial action described in Chapter 10, do not use the equipment and contact Olympus.

• Combination with other equipment

− Do not use the video system center in locations exposed

to direct strong electromagnetic radiations (for example,

microwave treatment device, short wave treatment device, MRI or radio equipment). Electromagnetic

radiation can interfere with the monitor display.

− Use only Olympus high-frequency electrosurgical

equipment with this unit. Non-Olympus equipment can cause interference on the monitor display or a loss of the

endoscopic image.

− Before using high-frequency electrosurgical equipment, be sure to install and connect the equipment according to

it’s instruction manual and make sure that the noise does

not affect the observation and surgical procedures. If high-frequency electrosurgical equipment is used without

such confirmation, patient injury may result.

• To activate the auto brightness control function of the light

source, the video system center should be turned ON. If it is not turned ON, the auto brightness control function is not

activated and the light intensity is set to maximum. In this

case, the endoscope distal end would become hot and could cause burns to the operator and physician (if a light source

model other than CLV-180 is used).

• When using spray-type medical agents such as lubricant,

anesthetic, or alcohol, use them away from the video system center so that the medical agents do not contact the video

system center. Medical agents might enter the video system

center through the ventilation grills and may cause equipment damage.

• Do not use a humidifier near the video system center as dew

condensation possibly might occur and it may cause

equipment failure.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

• High-frequency electrosurgical equipment can cause slight interference on the monitor display.

• Sometimes horizontal line noise appears when a slim

endoscope is used. To reduce the horizontal line noise,

select “Edge enhancement” for the enhancement setting.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

4.1 Operation flow

Please see the operation work flow in Figure 4.1 below. Follow each step of the

work flow for using the video system center.

1. Connect the endoscope to the video system center and the light source.

→ Section 4.2, “Connection of an endoscope” on page 46

2. Inspect the instruments before use.

→ Chapter 3, “Inspection” on page 33

3. Turns the instrument ON.

→ Section 4.3, “Turning the video system center ON” on page 50

4. Select a user name.

→ Section 4.4, “Recall of user preset data” on page 51

This operation can be skipped when using the user name of the last examination.

5. Adjust the white balance.

→ Section 4.5, “White balance adjustment” on page 52

When you are planning to use the NBI observation, perform the white balance adjustment for NBI

after performing the white balance for normal-light observation.

6. Enter the patient data.

→ Section 4.6, “Patient data” on page 57

It is possible to enter the patient data before the examination (see “Entering new patient data” on

page 137).

continued on next page

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

7. Perform examination.

→ Chapter 5, “Functions” on page 62

Changes iris mode,

Image enhancement,

Freezes image,

Zooms image,

Recording and printing of the images,

NBI observations, etc.

8. Terminate the examination.

→ Section 4.9, “Termination of the operation” on page 60

Press “EXAM END” key after the examination. Then turn the CV-180 and other instruments OFF.

Chapter 4 Operation

9. Disconnect the endoscope from the video system center and the light source.

→ Section 4.9, “Termination of the operation” on page 60

10. Inspect the instruments after use.

→ Chapter 7, “Care, Storage and Disposal” on page 155

For details on endoscope and light source, see the respective instruction manuals.

11. Reprocess and store the instrument and ancillary equipment as appropriate after use.

→ Chapter 7, “Care, Storage and Disposal” on page 155

For details on endoscope and light source, see the respective instruction manuals.

Figure 4.1

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

4.2 Connection of an endoscope

Connect the endoscope to the video system center and the light source. The

connection may require special cables. Refer to the instruction manuals of

ancillary equipment for details on the cables to be used.

• Make sure that the video plug and its electrical contacts are

completely dry before connecting the plug to the video

system center (see Figure 4.2). Wet equipment could cause the image to flicker or disappear.

“UP” mark

Figure 4.2

Video plug

Electrical contacts

• Do not apply excessive force to the camera cable of the

camera head by bending, stretching or crushing it. Also do not pull a bundle of camera cables, as this may cause

internal wire disconnection.

• Do not connect or disconnect the endoscope connector while this video system center is turned ON. Connecting or

disconnecting the endoscope while this video system center

is ON may destroy the CCD. Turn the video system center OFF before connecting or disconnecting the endoscope.

• Connect the video plug all the way into the socket. The

improper connection may increase image noise or may

cause disappearance of the endoscopic image during operation

• Be sure to refer to the instruction manuals of the ancillary

equipment including the endoscope and camera cable.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

VISERA series videoscope

Ensure that this instrument and all connected devices are turned OFF.

2. Connect the endoscope connector of the videoscope to the light source,

referring to the instruction manual for the light source.

3. Push the video plug into the video connector socket of the instrument all the

way until it clicks, holding this instrument with a hand so that it will not move.

Confirm that the “UP” mark points upwards (see Figure 4.3).

Chapter 4 Operation

“UP” mark

Video plug

Figure 4.3

Video connector socket

EVIS series videoscope and ultrasonic videoscope

Ensure that this instrument and all connected devices are turned OFF.

2. Connect the endoscope connector of the fiberscope to the light source

referring to the instruction manual for the light source.

3. Push the video plug of the scope cable EXERA II into the video connector

socket of the instrument all the way until it clicks, holding this instrument

with a hand so that it will not move. Confirm that the “UP” mark points

upwards (see Figure 4.3).

4. Connect the scope side connector of the scope cable EXERA II to the

endoscope, referring to the instruction manual of the endoscope.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

Fiberscope and camera head

Rigidscope and camera head

Ensure that this instrument and all connected devices are turned OFF.

2. Connect the endoscope connector of the fiberscope to the light source,

referring to the instruction manual for the light source.

3. Push the video plug of the camera head into the video connector socket of

the instrument all the way until it clicks, holding this instrument with a hand

so that it will not move. Confirm that the “UP” mark points upwards (see

Figure 4.3).

4. Connect the video adapter and camera head to the eyepiece section of the

fiberscope, referring to the instruction manuals for the video adapter and

camera head.

Ensure that this instrument and all connected devices are turned OFF.

2. Connect the light guide cable to the light source, referring to the instruction

manual for the light source.

3. Push the video plug of the camera head into the video connector socket of

the instrument all the way until it clicks, holding this instrument with a hand

so that it will not move. Confirm that the “UP” mark points upwards (see

Figure 4.3).

4. Attach the light guide cable, video adapter and camera head to the

rigidscope, referring to the instruction manuals for the light guide cable,

video adapter and camera head.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Summary of connection

This diagram gives an overview of all connections. For further details of the

connection, refer to the instruction manuals of the ancillary equipment being used.

CV-180

Chapter 4 Operation

Light source

VISERA series

Videoscope cable EXERA II

Video adapter

Camera head

Video adapters, camera heads, etc.

EVIS series and ultrasonic videoscope

Fiberscopes

Light guide cable

The numbers show the order of connection.

Figure 4.4

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Rigidscope

Chapter 4 Operation

4.3 Turning the video system center ON

1. Turn the ancillary equipment ON.

2. Turn the instrument ON by pressing the power switch (see Figure 4.5). The

indicator above the power switch lights up.

Power indicator

Power switch

Figure 4.5

3. The endoscopic image appears on the monitor (see Figure 4.6).

ID:

Name: Sex: Age: D.O.B. 12/12/2005 12:12:12

Physician: Comment:

Figure 4.6

For the procedure of turning the ancillary equipment ON,

refer to each instrument's instruction manual.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

4.4 Recall of user preset data

The operating conditions for each user (operator) can be recalled from the “User

preset” menu (see Section 9.3, “User preset” on page 215).

Confirm that the required user preset data is selected before

starting the observation. If different user preset data is used,

unintended operations may occur.

1. Press the “Shift” and “F2” keys together. The “User preset” menu appears

on the monitor (see Figure 4.7).

Chapter 4 Operation

Shift

Figure 4.7

Figure 4.8

2. Click the desired user name in the user name dialog box. The selected user

name is highlighted.

3. Check if the correct user name is selected, then click “Select”. The

endoscopic image appears on the monitor and the user preset data is loaded to the video system center.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

The user preset data used in the last operation before turning the video system center OFF comes up initially after turning

the instrument ON.

4.5 White balance adjustment

This adjustment procedure is used to display the correct image color on the

monitor. There are two white balance adjustments for the normal observation and the NBI observation. Be sure to always adjust the white balance in the

following cases:

• Before observation.

• After exchange of the light source.

• When any abnormality can be seen on the color of the image even if white balance adjustment has been completed.

• When adjusting the white balance of the endoscope to be

used in the sterilized zone, do not use the white cap (MH-

155) as described in this part, but use a white object such as

a piece of gauze without bringing it in contact with the

endoscope. Contact of the endoscope with a non-sterilized object may result in cross-contamination.

• Make sure that the endoscope and white cap (MH-155) are

clean before adjusting the white balance. Otherwise, cross-

contamination may result.

• Always control the color tone and/or enhancement of the image appropriately before observation. Setting an

inappropriate color tone or enhancement condition may

result in overlooking or wrong diagnosis.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

• Do not turn the video system center OFF or disconnect the

videoscope while the white balance button is being pressed

or the “Wh/B OK” indicator is blinking. Otherwise, the data

stored on the memory chip of the endoscope may be destroyed.

• When adjusting the white balance, always turn the light

source ON and take care not to expose the distal end of the

endoscope to external light. Otherwise, it may cause an incorrect white balance adjustment.

• Always use the white cap when setting the white balance for

the videoscope used in a non sterilized zone.

• Set the brightness level of the light source to “3” or the center

of the adjustment range before adjusting the white balance.

• When the color tone is not proper, white color cannot be

displayed properly on the monitor even if the white balance is set. Adjust the color tone to the center of the adjustable

range.

For normal light observation

Confirm the lighting status of the “Wh/B OK” (Wh/B = White balance)

indicator on the front panel (see Figure 4.9 and Table 4.1).

Wh/B OK indicator

Wh/B button

Figure 4.9

“Wh/B OK” indicator Status of white balance adjustment

OFF Before adjustment or if adjustment failed.

ON Completed.

Table 4.1

2. Proceed as follows according to the use of the endoscope.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

 When using an endoscope for the non-sterilized zone

1. Insert the endoscope's distal end into the white cap and hold the white cap

and endoscope stable to avoid wash-out of the monitor image (see Figure

4.10).

White cap

Direct view

Figure 4.10

Side view

2. Maintaining the stable condition in step 1., press the “Wh/B” button until a

short beep is generated. The result of the adjustment will be displayed on

the monitor for a few seconds (see Table 4.2).

Result Message

Completed successfully “White balance complete!”

“Check NBI white balance.”

(When using NBI compatible endoscope.)

Failed “White balance incomplete! Perform again!”

Table 4.2

3. Confirm that the “Wh/B OK” indicator is ON (see Table 4.1). If it is OFF, go

back to step 1. again.

When performing white balance adjustment keep an appropriate distance between distal end and white cap.

Otherwise, the white balance might not be adjusted properly.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

 When using an endoscope for the sterilized zone

1. Hold the endoscope stable to avoid wash-out of the monitor image, and

enlarge the image to the full monitor, monitoring a white object such as a

piece of gauze in such a way that it does not contact the endoscope.

2. Maintaining the stable condition in step 1., press the “Wh/B” button until a

short beep is generated. The result of white balance adjustment will be

displayed on the monitor for a few seconds (see Table 4.3).

Result Message

Completed successfully “White balance complete!”

“Check NBI white balance.”

(When using NBI compatible endoscope.)

Failed “White balance incomplete! Perform again!”

Table 4.3

3. Confirm that the “Wh/B OK” indicator is ON (see Table 4.1). If it is OFF, go

back to step 1. again.

For NBI observation

When connecting an NBI compatible endoscope, perform the white balance

adjustment for NBI observation after the white balance adjustment for normal

light observation has been performed.

1. Adjust the white balance for normal light observation according to “For

normal light observation” on page 53.

2. Switch to the NBI mode by operating the mode button of the light source.

Refer to the instruction manual of the light source.

3. Confirm that “NBI” appears on the monitor, and that the “NBI” indicator on

the front panel of the video system center turns from green to white.

4. Hold the endoscope as shown in step 1. of “When using an endoscope for

the non-sterilized zone” on page 54 or step 1. of “When using an endoscope

for the sterilized zone” on page 55 according to the use of it.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

5. Maintaining the stable condition in step 4., press the “Wh/B” button until a

short beep is generated. The result of the adjustment will be displayed on

the monitor for a few seconds (see Table 4.4).

Result Message

Completed successfully “NBI White Balance Complete!”

Failed “NBI White Balance Incomplete!”

Table 4.4

6. If the adjustment failed, perform the operation of steps 4. and 5. again.

7. Switch to the normal mode by operating the mode button of the light source.

Refer to the instruction manual of the light source.

8. Confirm that “NBI” disappears on the monitor, and that the “NBI” indicator on

the front panel of the video system center turns from green to white.

• The white balance adjustment can also be initiated by

pressing the “Shift” and “F9” keys on the keyboard together

instead of the “Wh/B” button.

• When the white balance adjustment cannot be completed, check if the color tone and/or brightness are correct and the

white cap is clean.

• Once the white balance adjustment is completed, the “Wh/B

OK” indicator keeps on lighting until the video system center is turned OFF.

• The white balance adjustment can also be initiated from the

endoscope's remote switches and/or foot switches.

For how to set up the remote switches and foot switches, see “Remote switch and foot switch (EXERA and VISERA)” on

page 218

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

4.6 Patient data

Before the observation, enter the patient data into the endoscopic image.

There are two methods to enter the patient data:

• Patient data can be entered immediately before the examination.

• A list of several patient data can be entered in advance.

This section explains how to enter patient data immediately before the examination. To enter a list of several patient data in advance, see Section 5.6,

“Pre-entry of patient data” on page 136.

Chapter 4 Operation

• Before entering patient data, press the “EXAM END” key to

clear the previous patient data. Otherwise, different patient data can be mixed on one print sheet and/or normal

functioning of the digital filing system cannot be guaranteed.

• When recording the images, be sure to record the images

together with the patient data. Otherwise distinction between different observations may become difficult.

• Be sure to enter the patient ID when entering patient data.

Also be sure to enter a different patient ID for each patient.

Otherwise, the image data for some patients may mix in the same image folder.

1. Press the “F1” key to change the monitor display full-patient-data display.

2. Press the “EXAM END” key to clear the previous patient data.

ID:

Name:

Cursor

Sex: Age: D.O.B. 12/12/2005 12:12:12

Physician: Comment:

Figure 4.11

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

3. Enter data.

Data data input condition Entry example

ID No. Up to 15 characters ABC123

Name Up to 20 characters Mike Johnson

Sex 1 character M

Age Up to 3 characters. Automatically calculated after entering D.O.B. 51

D.O.B. 8 characters. Enter the numbers according to the format (see

03031954

page 197).

Physician Up to 20 characters John Smith

Comment Up to 37 characters Cardiac end of the stomach

Table 4.5

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12

John Smith Cardiac end of the stomach

An example of displaying

Figure 4.12

4. When modifying data, press the arrow key to move the cursor to the input

position and edit the data.

5. When deleting all patient data displayed on the monitor, press the “EXAM

END” key on the keyboard (see Figure 4.13).

EXAM END

Figure 4.13

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

4.7 Observation of the endoscopic image

Observe the endoscopic image using the various functions provided with the

video system center. For details of the functions, see Chapter 5, “Functions”.

4.8 Recording of the observation image

Table 4.6 shows the devices that can record and/or print endoscopic images.

These devices can be controlled by the keyboard, scope switches, etc. For the operation of these devices, see Chapter 5, “Functions”.

Recording device Details

PC card Section 5.3, “Image recording and playback (PC card)” on

page 106

Digital file system “Image filing system” on page 127

Chapter 4 Operation

Videocassette recorder “Videocassette recorder (VCR)” on page 129

Video printer Section 5.5, “Printing images” on page 131

Table 4.6

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

4.9 Termination of the operation

Do not disconnect the video connector before turning the

video system center OFF. Otherwise, the endoscope or

camera head may be damaged.

1. Press the “EXAM END” key (see Figure 4.14) to execute the following

process;

• clearing patient data on the monitor;

• completing printing of un-printed images;

• closing the digital file system.

EXAM END

Scope side connector

Scope cable holder

Videoscope cable

Figure 4.14

2. Turn the instrument and ancillary equipment OFF.

3. When an EVIS series endoscope is used:

Disconnect the scope side connector of the videoscope cable, and place it on the scope cable holder (A in Figure 4.15). For disconnecting the video

plug, see B in Figure 4.15.

Video plug

A) When the scope side connector is not connected.

Figure 4.15

B) When both connectors are not connected.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 4 Operation

In B in Figure 4.15, insert the video plug to the scope cable holder in the direction of the arrow.

4. When a VISERA series endoscope or camera head is used:

Disconnect the video plug of the videoscope cable from the instrument,

holding the instrument with a hand so that it will not move and push the locking lever down (see Figure 4.16).

Video connector socket

Locking lever

Video plug

Figure 4.16

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

This chapter explains the functions of the buttons and keys on the video system

center. See the “System setup” menu and “User preset” menu in Chapter 9, “Function setup” for presetting.

5.1 Front panel

Image source buttons

Used to select the image source displayed on the monitor. The buttons other than the “SCOPE” button has to be pressed for more than 1 second to activate.

1. The Image source buttons select the images to be displayed on the monitor

(see Figure 5.1). The indicator above the active button lights up.

2. Confirm that the desired image appears on the monitor.

Image source buttons

Figure 5.1

Button Images on the monitor

SCOPE Endoscope’s live image Scope connector -

DV/VCR VCR, video recorder - VCR REMOTE or

PC Digital filing system - PC IN

Terminal and image sources

Front panel Rear panel

DIGITAL OUT

PRINTER Video printer - PRINTER IN

Table 5.1

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

When performing endoscopic observation, select the “SCOPE” image source.Images may disappear during

observation depending on the condition of ancillary

equipment.

When pressing an image source button to which no device is connected, the lamp above the button blinks and goes off

and the previous image appears on the monitor.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

PinP (picture in picture) display

The image of an external device connected to the following connectors can be

displayed on the monitor together with the endoscopic live image.

• PinP composite terminal on the front panel

(prior to the PinP Y/C terminal on the rear panel.)

• PinP Y/C terminal on the rear panel

The PinP function has two modes, “ON/OFF mode” and “Mode Change mode”.

The two modes display images in different ways. Presetting of PinP in the “User preset” menu is needed. See “PinP (picture in picture) function” on page 245.

1. Confirm that the external device is connected to either the PinP composite

terminal on the front panel or the PinP Y/C terminal on the rear panel (see

Figure 5.2).

SCOPE button

Figure 5.2

PinP button

Front panel

Rear panel

PinP composite terminal

PinP Y/C terminal

2. Press the “SCOPE” button to display the endoscopic live image.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

3. Press the “PinP” button. The sub image appears on the monitor (see Figure

5.3).

Main image

Sub image

PinP display

Figure 5.3

4. Press the “PinP” button to change the display. The transitions of the displays

are different according to the settings in “User preset” menu (see Figure 5.4

and Figure 5.5) (refer to “PinP (picture in picture) function” on page 245 for

the setting method).

PinP button

Endoscopic image

Screen transition in the “ON/OFF mode”

Note) The initial screen when pressing the PinP button depends on the user settings preset.

Endoscopic image

External image

PinP button

Either (see Note)

Endoscopic image

PinP button

Figure 5.4

External image

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

PinP button

Endoscopic image

External image

Screen transition in the “Mode change mode”

PinP button

External image

Figure 5.5

• All patient data disappears in the PinP display. Press the “F1”

key to display the data.

• The index image does not appear in the PinP display (see “Release index time” on page 242).

• It takes a few seconds before the PinP display appears

depending on the devices connected.

External image

Endoscopic image

PinP buttonPinP button

• The PinP function is also controlled from the scope switches

and/or foot switches. For how to set up the scope switches and foot switches. See “Remote switch and foot switch

(EXERA and VISERA)” on page 218.

• The output signal is just SDTV in PinP display.

• Before activating the PinP function make sure that an

endoscope is connected to this instrument. If no endoscope is connected it might not be possible to use the PinP function

and image recording of an external device may not work.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Image enhancement mode (ENH.)

The image enhancement function electrically increases the sharpness of the

endoscopic live image. Three enhancement modes and normal modes are available. The type and level of image enhancement should be set in advance.

See “Image enhancement (normal observation)” on page 225 and “Image

enhancement (NBI observation)” on page 249.

1. Press the “ENH.” button to change the enhancement mode (see Figure 5.6).

The indicator above the button lights up and the selected mode is displayed

on the monitor for a few seconds.

ENH. button

Enhancement mode

ID:

Name: Sex: Age: D.O.B. 12/12/2005 12:12:12

Ct: N Eh: A8 Z: x1.5

Chapter 5 Functions

Enhancement OFF

Enhance：A8

Physician: Comment:

Figure 5.6

2. To switch OFF the image enhancement at any mode, press and hold the

“ENH.” button. The indicator above the button goes OFF.

ENH. button

Mode 1

ENH. button

Mode 2

Press and hold ENH. button

Enhancement ON

ENH. button

Mode 3

Figure 5.7

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

• Mesh-like noise may be observed in the image when the image enhancement function is ON during use of a

fiberscope or hybrid endoscope. In this case, use the

recommended camera head, or switch the image enhancement OFF.

− OTV-S7H-1N, OTV-S7H-1D, OTV-S7H-1NA

• The image enhancement mode used in the last operation

before turning the video system center OFF comes up when

the instrument is turned ON.

• The image enhancement function can also be controlled from

the scope switches and/or foot switches. For how to set up the scope switches and foot switches, see “Remote switch

and foot switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Iris mode

Chapter 5 Functions

This operation selects the method to measure the brightness of the object of the

observation. Two iris modes, peak mode and auto mode, are available. For details on the iris mode, see “Iris” on page 231.

1. Press the “IRIS” button on the front panel to switch between auto mode and

peak mode alternately. The indicator above the iris mode button lights up.

IRIS button

Figure 5.8

• The iris mode used in the last operation before the video

system center is turned OFF comes up when the instrument

is turned ON.

• The iris mode can also be controlled from the scope switches

and/or foot switches. For how to set up the scope switches and foot switches, see “Remote switch and foot switch

(EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

White balance

The “Wh/B” button performs the white balance adjustment to reproduce colors in

their original tones. The “Wh/B OK” indicator indicates if the white balance adjustment is completed or not. For details of the operation, see Section 4.5,

“White balance adjustment” on page 52.

Wh/B OK indicator

Wh/B button

Figure 5.9

• The white balance adjustment can also be activated by pressing the “Shift” and “F9” keys on the keyboard.

• The white balance adjustment can also be controlled from

the scope switches and/or foot switches. For how to set up

the scope switches and foot switches, see “Remote switch and foot switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Brightness adjustment (Exposure)

The brightness of the live images can be adjusted. The lamp brightness is

automatically adjusted to keep the brightness of the image constant when the light source is set to “AUTO”. The lamp brightness is manually adjusted to keep

the lamp brightness constant at the setting value when the light source is set to

“MAN.”. The function differs depending on the following conditions:

• The light source and its settings.

• The setting of the electric shutter function

(refer to “Electronic shutter” on page 239)

Chapter 5 Functions

Light

source

CLV-180 AUTO Independent of

Other

than

above

Light

source

mode

MAN. Automatically

AUTO ON • Set the light intensity of the light

MAN. ON Do not use this setting (see page 74).

Endoscope’s

electronic

shutter

ON/OFF of the

electronic shutter

function.

becomes OFF.

OFF Adjust the brightness using the

Brightness adjustment Brightness level indication

Adjust the brightness using the

“EXPOSURE” buttons on the front panel.

The lamp brightness is automatically

adjusted to keep the image brightness

constant.

Adjust the brightness using the

“EXPOSURE” buttons on the front panel.

The lamp brightness remains constant.

source to the center of the adjustable

range.

• Adjust the brightness using the

“EXPOSURE” buttons on the front

panel. The lamp brightness is

automatically adjusted to keep the

image brightness constant.

brightness adjustment buttons on the

light source. The lamp brightness is

automatically adjusted to keep the image

brightness constant.

The light intensity reaches its greatest

value, and excessive heat of the

endoscope's distal end may occur.

• The level indicators of the

video system center and

light source are interlocked.

• The “EXPOSURE” indicator

is a dot display.

• The level indicators of the

video system center and

light source are interlocked.

• The “EXPOSURE”

indicator is a bar display.

• The level indicators of this

instrument and light source

are not interlocked.

• The “EXPOSURE” indicator

is a dot display.

The “EXPOSURE” indicator

goes OFF.

OFF Adjust the brightness using the

brightness adjustment buttons on the

light source.

Table 5.2

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

The “EXPOSURE” indicator

goes OFF.

Chapter 5 Functions

• Always use the minimum level of illumination necessary for adequate viewing. Whenever possible, avoid close,

stationary viewing of mucous membranes for a long time.

Intense endoscopic illumination may cause mucosal burns.

• Do not bring the metal plug of the light guide and the distal end of the endoscope immediately after use in contact with

the body and flammable objects because the parts will be

extremely hot.

• Be sure to set the brightness control mode of the light source to manual mode or turn the examination lamp OFF before

disconnecting the camera head from the endoscope or

disconnecting the videoscope from the video system center.

Disconnecting them can increase the light intensity to the maximum and may cause burns or eye injury.

Refer to the instruction manual of the endoscope for details

of the electric shutter function.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

 CLV-180

The video system center can adjust the brightness of the light source.

1. Set the brightness control of the light source to “AUTO” or “MAN.” according

to the instruction manual of the light source.

2. Set the brightness, using the “EXPOSURE” buttons on the front panel (see

Figure 5.10). The brightness level is displayed on the “EXPOSURE” indicator.

EXPOSURE indicator

EXPOSURE buttons

Figure 5.10

• Each time the “EXPOSURE” button is pressed the indicator

changes by 1 level. Pressing and holding the button, changes the indicator continuously.

• The “EXPOSURE” indication is interlocked with the

brightness level indication of the connected CLV-180. When

the brightness adjustment buttons on the CLV-180 are pressed, the “EXPOSURE” indication on the video system

center varies in an interlocked operation.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

 Other than CLV-180 in AUTO mode

The operation differs depending on the setting of the electronic shutter function of the endoscope (refer to “Electronic shutter” on page 239).

When the electronic shutter function is ON:

1. Set the brightness level of the light source to the center of the adjustable

range.

2. Set the brightness using the “EXPOSURE” buttons on the front panel of the

video system center. The brightness level is displayed on the “EXPOSURE” indicator.

When the brightness level of the light source is not in the

center of the adjustable range, intense light, which is not

recognized clearly, may cause burns and/or appropriate brightness may not be obtained.

When the electronic shutter function is OFF:

Set the brightness as required, using the brightness adjustment buttons of the

light source. The brightness level is displayed on the light source.

The “EXPOSURE” buttons of the video system center is

invalid, and the “EXPOSURE” indicator goes OFF.

 Other than CLV-180 in MANUAL mode

Never set the electronic shutter function to ON in the user preset menu (refer to “Electronic shutter” on page 239).

Intense light, which is not recognized clearly, may cause

burns.

Set the brightness as required, using the brightness adjustment buttons of the

light source. The brightness level is displayed on the light source.

The “EXPOSURE” buttons of the video system center is invalid, and the “EXPOSURE” indicator goes OFF.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

STOP button and PC card indicator

This button stops accessing the PC card. Press the button before ejecting the

PC card from the PC card slot.

Be sure to press the “STOP” button and confirm that the PC

card status indicator goes OFF before ejecting the PC card from the PC card slot. Otherwise, the PC card and/or data

stored may be destroyed.

1. Press the “STOP” button before removing the PC card. The PC card status

indicator goes OFF.

Chapter 5 Functions

STOP button

PC card status indicator

Figure 5.11

The PC card indicator shows the status as shown below.

PC card indicator Status

OFF No PC card in the slot, or the video system center does

not recognize the PC card.

Green The PC card is in the slot, and the video system indicator

has recognized the PC card.

Orange (blinking) The video system indicator is accessing the PC card.

Table 5.3

The images cannot be recorded when the PC card is not

ejected after pressing the “STOP” button. Press the eject button to eject the PC card after a few seconds, then insert

the PC card again to let the video system center recognize

the PC card.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

PC card slot and eject button

Eject button

PC card slot

Figure 5.12

Table 5.4 shows the applicable PC card adapter and Memory Card.

Applicable device Specification

PC card adopter MAPC-10 (Olympus)

Memory Card xD picture card

M-XD32P, M-XD64P, M-XD128P, M-XD256P, M-XD512P,

M-XD1GM (Olympus)

Table 5.4

• Be sure to confirm the followings. Otherwise, recording or

playing back images on the PC card may not be possible.

− Format the PC card before the first use as described in

“Formatting of the PC card” on page 114.

− Use the CV-180 for formatting the PC card. Do not use a

personal computer, etc.

• Be sure to confirm the followings. Otherwise, the PC card

and the data in the PC card may be destroyed.

− Do not press the “STOP” button while the PC card status

indicator is blinking.

− Do not press the “STOP” button while formatting the PC

card.

− Press the “STOP” button and confirm if the PC card status

indicator goes OFF before ejecting the PC card from the

PC card slot.

− Handle the PC card with care and avoid subjecting them

to sudden or severe impact.

− Do not place the PC card in a place subject to strong

static electricity, electricity or magnetism.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

− Do not leave the PC card under high temperatures, high humidity or in a corrosive atmosphere.

• Do not allow a foreign object to penetrate the inside of the PC

card slot. Otherwise, the equipment may be damaged.

• Do not touch the PC card with wet hands. The video system

center and/or data stored may be destroyed.

• See the following pages for details on how to record the PC

card.

− Images:

Section 5.3, “Image recording and playback (PC card)” on

page 106.

− Patient data:

“Recording patient data into PC card” on page 144.

“Loading patient data from PC card” on page 146.

• Please use only the PC card adapter and Memory Card from Olympus. Other cards might not work properly.

• The PC card of CardBus type and Smart Media are not

available.

 Insertion of PC card into the PC card slot

1. Insert the xD picture card into the PC card adapter.

2. Push the PC card adapter all the way into the PC card slot.

PC card status indicator

PC card adapter

Figure 5.13

3. The video system center recognizes the PC card, and the PC card status

indicator lights up green.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

• If the video system center does not recognize the PC card, eject and reinsert the PC card adapter, or turn the video

system center OFF then ON again, leaving the PC card

adapter inserted.

• Always prepare spare PC cards for use when the currently used card becomes full.

• It is recommended to move the image data on the PC card

into a personal computer regularly.

 Ejection of PC card from the PC card slot

Be sure to press the “STOP” button and confirm that the PC

card status indicator goes OFF before ejecting the PC card from the PC card slot. Otherwise, the PC card and/or data

stored may be destroyed.

1. Press the “STOP” button. The PC card status indicator goes OFF (see

Figure 5.14).

STOP button

PC card status indicator

Figure 5.14

Eject button

2. Press the eject button.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

3. Press the eject button again. The PC card adapter comes out slightly (see

Figure 5.15).

Eject button

PC card adapter

Figure 5.15

4. Pull the PC card adapter straight out.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

RESET button

The “RESET” button resets the settings modified during use of the video system

center to the original values. The settings to be reset are the following items:

• User preset data: To be reset to their original settings.

• Items shown in Table 5.5: To be reset to the factory defaults.

Function Default setting

Image source Scope

Color tone R [0]

G[0]

C[0]

Freeze Live image

Release index 4 sec

Zoom x1.0

Special light observation Normal observation

Arrow pointer OFF

Stop watch OFF

Characters on screen Full display

Exposure Center

PinP OFF

Table 5.5

1. Press and hold the “RESET” button on the front panel (see Figure 5.16). All

front panel indicators should blink for about 1 second, then the settings are

reset.

RESET button

Figure 5.16

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

5.2 Keyboard

Domepoint

The domepoint is used to move the arrow pointer, and execute the function on the screen or move the cursor on the screen. It refers as “clicking” to press the

“Click” key one time, placing the arrow pointer at the desired area.

1. Press the domepoint using your finger tip. The arrow pointer on the screen

Chapter 5 Functions

moves to the direction corresponding to the pressed part of the domepoint.

Click key

The arrow pointer moves to the right if pressing the right side of the domepoint.

Monitor screen

Arrow pointer on the screen

Figure 5.17

Domepoint

2. Move the arrow pointer to a text box area. Click the text box to place the

cursor.

Cursor

Text box

Time

Date

Click the text box to place the cursor.

Figure 5.18

3. Click a button on the menu to move the highlight, or perform the function of

the button.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Time

Date

The cursor moves.

Chapter 5 Functions

Clearing characters from the screen (“F1”)

Also refer to Section 2.8, “Pointer” on page 32 for the operation of cursor and highlight.

This operation clears and redisplays the text information such as patient data on

the monitor screen.

Part of the patient data disappears from the monitor screen each time the “F1”

key is pressed. The fourth press redisplays the initial display showing all patient

data (see Figure 5.20 for the transition of the display).

Figure 5.19

• The zoom ratio of the image except “x1.0” is always

displayed on the monitor even when the text information is

cleared.

• Only when all text data are displayed on the monitor, the patient data can be entered.

• The image size and layout may differ from those shown in

Figure 5.20 depending on the connected endoscope.

• The patient data can also be cleared using the scope

switches and/or foot switches. For how to set up the scope switches and foot switches, see “Remote switch and foot

switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

Full display

All clear

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

John Smith Cardiac end of the stomach

Z: x1.5

ABC123　　　　　　　　　Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

John Smith Cardiac end of the stomach

Press F1 key

Z: x1.5

Clear 2

Clear 1

Press F1 key

ABC123 Mike Johnson

Z: x1.5

ABC123 Mike Johnson

12/12/2005

CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump

  

Media:

Press F1 key

ABC123　　　　　　　　　Mike Johnson

Z: x1.5

ABC123　　　　　　　　　Mike Johnson

12/12/2005

CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

John Smith Cardiac end of the stomach

Figure 5.20

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

System setup (“Shift” + “F1”)

Press these keys to open the system setup menu that enables the proper use of

the video system center and ancillary equipment. For details on the system setup menu, see Section 9.2, “System setup” on page 194.

Shift

Figure 5.21

Scope information (“F2”)

Press this key to open the scope information window. For details, see Section

5.7, “Scope information” on page 148.

Figure 5.22

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

User preset (“Shift” + “F2”)

Press these keys to open the user preset menu that sets up the observation

conditions for each user (operator). For details on the user preset menu, see Section 9.3, “User preset” on page 215.

Chapter 5 Functions

Shift

Figure 5.23

Cursor (“F3”)

Press to switch the display of the cursor on the screen between ON and OFF.

Figure 5.24

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

Patient data (“Shift” + F3)

Press these keys to open “Patient Data” menu to enter the patient data. For

details on the patient data menu, see “Entering new patient data” on page 137.

Shift

Figure 5.25

Freeze mode (“F4”)

This key switches between the two different freeze modes that pause the

endoscopic live image.

Figure 5.26

The freeze mode switches between “frame” and “field” each time the “F4” key is pressed. For more information of the freeze mode, see “Freeze function” on

page 224.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Browse (“Shift” + “F4”)

Press these keys to open the PC card menu. The PC card displays the

endoscopic images and patient data stored on the PC card. See “PC card menu” on page 110.

Press the “Shift” and “F4” keys together to open the PC card menu.

Chapter 5 Functions

Shift

Figure 5.27

Figure 5.28

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

Stopwatch (“F5”)

Press the “F5” key to change the clock on the monitor screen to a stopwatch.

Use the “F5” key also to start and stop counting (see Figure 5.30).

Figure 5.29

ABC123

Clock 12:12:12 (H : M : S)

Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12

Stop watch <00:00:00> (H : M : S)

Figure 5.30

Clock

Figure 5.31

Ct: N Eh: A8 Z: x1.5

John Smith Cardiac end of the stomach

Stop watch

Timing start

Timing stop

Shift+F5

The stopwatch operation can also be controlled from the

scope switches and/or foot switches. For how to set up the scope switches and foot switches, see “Remote switch and

foot switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Automatic gain control (AGC) (“F6”)

If necessary set up the AGC function in advance. See “Auto gain control (AGC)”

on page 236.

1. The AGC function is turned ON and OFF alternately each time the “F6” key

is pressed. The AGC status, ON or OFF, is displayed on the monitor for

about 2 seconds (see Figure 5.33).

Chapter 5 Functions

Figure 5.32

AGC ON/OFF window

Figure 5.33

• Image noise may appear when AGC is ON.

• The AGC function cannot be switched ON or OFF while the

image is frozen.

• The AGC function used in the last operation before turning

the instrument OFF comes up, when the instrument is turned

ON.

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

　　AGC 　　ON

John Smith Cardiac end of the stomach

• The AGC switching operation can also be controlled from the

scope switches and/or foot switches. For how to set up the

scope switches and foot switches, see “Remote switch and

foot switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

Contrast mode (“Shift” + “F6”)

Pressing these keys changes the contrast of the endoscopic image.

Mode Explanation

Normal Standard setting

High Darkens the dark part and brightens the bright part compared to the

normal observation.

Low Brightens the dark part and darkens the bright part compared to the

normal observation.

Table 5.6

1. Press the “Shift” and “F6” keys together. Every time the two keys are

pressed, the contrast mode changes. The selected mode is displayed on the monitor (see Figure 5.35).

N: Normal

H: High

L: Low

Figure 5.34

Contrast indication

Contrast window

Shift

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:

  

　Contrast Normal

John Smith Cardiac end of the stomach

Figure 5.35

• The contrast mode function does not work during the special

light observation.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

• The contrast mode can also be controlled from the scope

Image zooming (“F7”)

The endoscopic image can electrically be magnified, when using the endoscope compatible with the electronic zooming function (Scope 1, Scope 4, and Scope 5

in Table 9.30 on page 228). Three zoom ratios, x1, x1.2, x1.5, are available. The

image area size does not change.

Press the “F7” key to change the zoom ratio. The zoom ratio is displayed on the

monitor for about 2 seconds (see Figure 5.37).

Chapter 5 Functions

switches and foot switches. For how to set up the scope

switches and foot switches, “Remote switch and foot switch

(EXERA and VISERA)” on page 218.

Figure 5.36

Zoom ratio indication

Zoom window

x1.2

Transition of the zoom ratio (example)

Figure 5.37

x1.5

ABC123 Mike Johnson M 51 03/03/1954 12/12/2005 12:12:12 CVP: A4/4 D.F: 99 VCR Ct: N Eh: A8 Z: x1.5 Pump Media:  

Zoom

x 1.5 John Smith Cardiac end of the stomach

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Chapter 5 Functions

• The image area size can be changed during zooming (see “Image size (“F8”)” on page 94). When the zoom ratio returns

to x1, the image area size also returns to the original size.

• While the image is frozen, the zoom function is not active.

• When the zoom ratio is x1, the zoom ratio is not displayed on

the monitor.

• This instrument always starts with zoom ratio x1.

• The zoom ratio is displayed at the lower left on the monitor

when the text information is cleared on the monitor.

• The zoom ratio can also be controlled from the scope switches and/or foot switches. For how to set up the scope

switches and foot switches, see “Remote switch and foot

switch (EXERA and VISERA)” on page 218.

EVIS EXERA II VIDEO SYSTEM CENTER CV-180

Olympus CV-180 User manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INSTRUCTIONS

EVIS EXERA II VIDEO SYSTEM CENTER

OLYMPUS CV-180

Contents

Labels and Symbols

Intended use

Instruction manual

User qualifications

Instrument compatibility

Repair and modification

Signal words

Dangers, warnings and cautions

TYPE CF applied part

TYPE BF applied part

TYPE B applied part

Cardiac applications

Summary of Equipment Functions

Displaying the endoscopic images on the monitor

Special light observation

Adjusting the endoscopic images

Entering patient data

Customizing the operations

Recording images

Operation of ancillary equipment

Chapter 1 Checking the Package Contents

Chapter 2 Nomenclature and Functions

2.1 Front panel

1. Power switch

2. Power indicator

3. Video connector socket

4. Locking lever

5. Image source buttons

6. Picture in picture (PinP) button

7. White balance (Wh/B) button

8. White balance (Wh/B OK) indicator

9. HDTV indicator

10. NBI indicator

11. Exposure adjustment (EXPOSURE) buttons

12. Exposure level (EXPOSURE) indicator

13. PinP composite terminal

14. PC card slot

15. Eject button

16. PC card status indicator

17. STOP button

18. Iris mode (IRIS) button

19. Iris mode indicators

20. Image enhancement mode (ENH.) button

21. Image enhancement mode indicators

22. RESET button

2.2 Rear panel

1. Keyboard terminal

2. Y/C OUT terminal

3. Printer IN terminal

4. Printer OUT terminal

5. Printer remote terminal

6. PC OUT terminal

7. PC IN terminal

8. PC remote terminal

9. Remote terminal

10. Option terminal

11. Foot switch terminal

12. VCR remote terminal

13. Fuse box

14. AC power inlet

15. Light control terminal

16. Light source terminal

17. PinP Y/C terminal

18. HD/SD SDI OUT terminal

19. Digital OUT terminal

20. PC OUT2 terminal

21. Monitor remote terminal

22. Composite OUT terminal

23. Monitor OUT terminal

24. Potential equalization terminal

2.3 Keyboard

1. F1 key