B. DISASSEMBLY AND ASSEMBLY PROCEDURE
C-5050 ZOOM
B. DISASSEMBLY AND ASSEMBLY
PROCEDURE
[1] REMOVAL OF CABI BACK, CABI FRONT AND CABINET TOP .......................... B-2
[2] REMOVAL OF TB3 BOARD AND TB2 BOARD .....................................................B-3
[3] REMOVAL OF LCD AND TB1 BOARD ..................................................................B-3
[4] REMOVAL OF ST1 BOARD....................................................................................B-4
[5] REMOVAL OF CA1 BOARD CP1 BOARD
PW1 BOARD AND BOARD LOCATION ................................................................B-5
B-1 Ver.1
B. DISASSEMBLY AND ASSEMBLY PROCEDURE C-5050 ZOOM
[1] REMOVAL OF CABI BACK, CABI FRONT AND CABINET TOP
Disassembly perform as follows and assembly perform by reversing the disassembly steps.
Be sure to discharge the main capacitor, then continue to disassembling.
! Beware of electric shock
Danger of electric shock.
Use a discharging tool to remove
the electrical charge before working.
10
30
31
9
11
8
7
18
17
13
5
4
28
Discharge point of C5412
Red
Grey
24
6
26
32
23
27
19
21
25
22
20
13. Cabi front
14. Discharge both of C5412.
15. Cover USB
16. Cover DC jack
17. Cover card
18. Shaft card
19. Screw 1.7 x 4
20. Screws 1.7 x 3.5
21. Earth cabi
22. Screws 2 x 3
23. Stand
24. Screw 1.7 x 4
25. Cabi back
26. Spring plate card
27. Two FPCs
28. Cover battery
29. Shaft battery
30. Screw 1.7 x 4
31. Cabinet top
32. FPC
12
1
15
2
Discharge both
3
of C5412.
1. Open the cover USB.
2. Open the DC jack.
29
3. Screws 1.7 x 4
4. Screws 1.7 x 3.5
5. Screws 2 x 3
6. Open the cover card.
7. Two screws 1.7 x 8
8. Cover terminal H
9. Spring terminal H
10. Four screws 1.6 x 5
11. Holder terminal H
12. Open the cover battery
16
B-2 Ver. 1
B. DISASSEMBLY AND ASSEMBLY PROCEDUREC-5050 ZOOM
2
[2] REMOVAL OF TB3 BOARD AND TB2 BOARD
15
8
5
14
11
6
10
3
1
9
12
13
1. Two screws 1.7 x 3.5
2. Button AEL
7
2
4
3. Connector
4. TB3 board
5. Three screws 1.7 x 2.5
6. Holder speaker
7. Connector
8. Speaker
9. Three screws 1.7 x 3.5
10. TB2 board
11. Two FPCs
12. Flexible PWB
13. Button back
14. Two screws 1.7 x 3.5
15. Unit CMD
[3] REMOVAL OF LCD AND TB1 BOARD
5
1
6
7
10
8
9
4
5
1. Two screws 1.4 x 4
2. Cover joint
3. Five screws 1.7 x 2
4. Two screws 1.7 x 6
5. Two screws 1.7 x 4
6. Cover front LCD
7. LCD
8. FPC
9. TB1 board
10. Holder monitor
3
B-3 Ver. 1
[4] REMOVAL OF ST1 BOARD
B. DISASSEMBLY AND ASSEMBLY PROCEDURE C-5050 ZOOM
1. Remove the solder
2. Remove the solder
3. Dec flash
4. FPC
5. LCD
6. Screw 1.7 x 3.5
7. Screw 1.7 x 3.5
8. Screw 1.7 x 3.5
9. ST1 board
10. Cover trans
3
11
13
11. Screw 1.7 x 4
12. FPC
13. Unit SLD
14. Connector
15. Spacer spring C
16. screw 1.7 x 3.5
17. screw 1.7 x 3.5
18. Three screws 1.7 x 9
19. FPC
20. Unit flexible joint
21. Spring AF LED
5
4
6
9
8
12
B
15
16
20
17
19
21
18
10
7
A
14
2
B
A
1
B-4 Ver. 1
B. DISASSEMBLY AND ASSEMBLY PROCEDUREC-5050 ZOOM
P
rd
[5] REMOVAL OF CA1 BOARD, CP1 BOARD, PW1 BOARD AND BOARD LOCATION
1. FPC
2. FPC
3. FPC
4. Three screws 1.7 x 3.5
5. Screw 1.7 x 2.5
6. Holder jack
7. Connector
8. CP1 board
9. Flexible PWB
10. Remove the solder
11. Four screws 1.7 x 4
12. Two screws 2 x 6
13. Screw 2 x 2.5
14. CA1 board
15. Remove the solder
16. Four screws 1.7 x 3.5
17. Earth B
18. Earth A
19. Shield tape PW1
20. PW1 board
11
9
8
4
16
5
20
10
15
18
1
7
F
G
C
D
E
2
17
19
D
E
C
13
3
6
G
12
F
14
CCD
CP1 board
TB2 board
TB3 board
Lens
When uniting LENS and View Finder(VF).
1. VF Lens should be moved to the end of
wide side.
2. VF Cam should be positioned correctly as
TB1 boa
W1 board
ST1 board
CA1 board
shown in the figure.
B-5 Ver. 1
Loading...