Auto Operation
Program Select
RESET
AUTO
(Main Prg_Oper)
(Program Select)
Positioning Cursor to target filename.
|
|
7 |
( OK ) |
|
|
|
( Close |
|
|
8 |
OKUMA MacTurn250 by S.Fukazaki
Auto Operation
Zero shifts for Air cut
ZERO SET
Move the cursor to Zero shift X-Axis or Z-Axis.
(ADD
○○○ ENTER Shift value
Attn. Only 1time valid. After Reset automatic 0.
OKUMA MacTurn250 by S.Fukazaki
Auto Operation
Tool Data Adjust
1.TOOL DATA
2.F 7 (ITEM) press until Tool OFFSET screen.
3.Conform Spindle mode. 1spindle mode or 2spindle mode
4.Change the Cutting position Base or Vertical.
5.Change the Tool No. By Page key or Cursor key.
6.Positioning Cursor to X-axis or Z-axis.
7.F 2 ADD If no Function key then press Extend
8.○○○ ENTER Adjust value
Example |
ENTER |
-------------- make 0.01 small |
Attn.
More them is limited by parameter. (Changeable)
OKUMA MacTurn250 by S.Fukazaki
Setup
Soft Limit Setting
|
Manual |
Move Turret to target position. |
||
|
|
|
|
|
Parameter |
||||
|
|
|
Change Screen |
|
|
F 8 |
|||
|
|
|
User Para |
|
|
F 2 |
|||
Move the Cursor to target axis. |
||||
|
|
|
CAL |
|
|
F 3 |
|||
|
|
|
|
|
ENTER |
|
|
||
Attn.
Please do not mistake plus and minus.
For make width, press F 2(ADD) then write adjusts value.
For make maximum limit, at system parameter stroke end limit ADD “ ” write then automatic setting to soft limit same as stroke
limit. Do not change system stroke limit.
OKUMA MacTurn250 by S.Fukazaki
Setup
Turret Index
Manual
Manual move turret to X-axis soft limit position.
Check the interference between turret and spindle tailstock.
Turret Index
MDIClose door.
MDI
G HP=4 ENTER
START
T○○○M ENTER ----- Sub-spindle M/C don’t need M66
or (offset spec is 1000or3000)
START
OKUMA MacTurn250 by S.Fukazaki
Setup
Tool Registration
TOOL DATA
ITEM press until Tool Information screen.
Move cursor to turret No.
SET
Tool number ENTER
MENU
3 -Tool or 4 -Tool
If not standard size selects the size.
7
Attn.
Standard size is run dram pot.
Big size is fix pot.
OKUMA MacTurn250 by S.Fukazaki
Manual Tool Exchange
Manual Index turret. Refer to attached sheet.
Move Turret to the place which work tends to perform.
Manual Tool Exchange ON
Put Turret operation box on near place with a magnet.
Hold Tool by hand.
Unclamp
Exchange Tool.
Clamp
Return Turret operation box.
Manual Tool Exchange OFF
Input Tool data information. Refer to attached sheet.
OKUMA MacTurn250 by S.Fukazaki
Setup |
|
Setup |
Manual close door.
If return cycle is on then press Return Cycle
MDI
○○○ ENTER ○○○ is Tool Number 0 210
is turret No. (MacT250 = 01 only) Example ENTER------ Return Tool and on Turret empty. Example2 =101 ENTER---- Tool No.1 prepay.
5. START
6. |
ENTER |
------- Okuma standard is M421 |
7.Single block off and Feed override .
8.START
9.Wait until Run lamp off.
OKUMA MacTurn250 by S.Fukazaki
|
|
|
|
|
|
|
|
|
|
|
|
EDIT mode |
|
Create New File |
|
|
|
|
|||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
EDIT mode |
|
|
|
|
|
|
|
|
|
|
|||
|
|
(New) |
If have a One touch IGF then press |
|
( ) |
||||||||
3 |
|
||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
New file name |
|
|
|
|
|
|
Head character must be English and |
||||||
|
|
ENTER |
|||||||||||
max.16 characters. |
|
|
|
|
|||||||||
Example1. |
|
|
|
|
Create “ABC.MIN” file. |
||||||||
|
ENTER |
||||||||||||
Example |
|
Create “ABC.SSB” file. |
|||||||||||
ENTER |
|||||||||||||
Do edit operation. |
|
|
|
|
|||||||||
5. 8 Stop Quit or Extend 8 Select quit
I recommend “Select quit” because after not need program select.
OKUMA MacTurn250 by S.Fukazaki
EDIT mode
File Editing
EDIT mode
Move cursor to target filename.
|
|
2 |
(EDIT) or just |
ENTER |
|
|
|
Do edit operation. |
|
|
|
|
|||
|
|
Stop Quit or |
Extend |
|
Select quit |
||
|
|
8 |
8 |
||||
I recommend Select quit because after not need program select.
OKUMA MacTurn250 by S.Fukazaki
EDIT mode
File copy then create new file
1.EDIT mode
2.Move cursor to source file name.
3.F 5 (Copy)
4.Input new file name. --------Head character must be English and max.16 characters.
5.F 1 (MD1 Copy)
OKUMA MacTurn250 by S.Fukazaki
Setup
Chuck work / Center work Change parameter
|
Parameter |
|
||
|
|
|
Change Screen |
|
|
|
8 |
||
|
|
|
Tailstock |
|
|
|
|
||
↑ Cursor to upper position.
|
|
|
MENU |
||
|
|
|
Chuck work or |
|
Center work |
|
|
2 |
3 |
||
Attn.
For cutting jaw. Change to chuck work.
OKUMA MacTurn250 by S.Fukazaki
Loading...