Page 1
Model No. NTM58020
Serial No. _
Serial Number
Decal (on frame)
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
USER’S MANUAL
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE. The
trained technicians on our customer hot line will provide immediate assistance, free of charge to
you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
Visit our website at
www.nordictrack.com
new products, prizes,
fitness tips, and much more!
Page 2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
HOW TO OPERATE THE STEPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
NordicTrack®is a registered trademark of ICON Health & Fitness, Inc.
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the stepper.
1. Read all instructions in this manual before
using the stepper.
2. Use the stepper only as described in this
manual.
3. It is the responsibility of the owner to ensure
that all users of the stepper are adequately
informed of all precautions.
4. Place the stepper on a level surface. Cover
the floor beneath the stepper to protect the
floor or carpet. Keep the stepper indoors,
away from moisture and dust.
5. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
6. Keep children under the age of 12 and pets
away from the stepper at all times.
7. The stepper should not be used by persons
weighing more than 250 pounds.
8. Always wear suitable exercise clothing
when using the stepper. Wear athletic shoes
for foot protection.
9. Always hold the handlebars when mounting,
dismounting, or using the stepper.
10. Keep your back straight when using the
stepper; do not arch your back.
11. If you feel pain or dizziness while exercising, stop immediately and cool down.
12. The stepper is intended for in-home use
only. Do not use the stepper in a commercial, rental, or institutional setting.
13. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
2
Page 3
BEFORE YOU BEGIN
Congratulations for selecting the new NordicTrack
MTN 740 stepper. Stepping is one of the most effective exercises for increasing cardiovascular fitness,
building endurance, and toning the entire body. The
NordicTrack®MTN 740 stepper blends advanced engineering with innovative styling to let you enjoy this
exercise in the convenience and privacy of your home.
For your benefit, read this manual carefully before
you use the stepper. If you have questions after
reading this manual, please call our Customer Service
Fan
Handlebar
Water Bottle Holder*
®
Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is NTM58020. The
serial number can be found on a decal attached to the
stepper (see the front cover of this manual for the
location of the decal).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Rack
Console
FRONT
Side Shield
Wheel
LEFT SIDE
*No water bottle is included
Pulse Sensor
BACK
Pedal
Adjustable Foot
3
Page 4
ASSEMBLY
Assembly requires two people. Place all parts of the stepper in a cleared area and remove the packing mate-
rials. Do not dispose of the packing materials until assembly is completed. In addition to the included allen
wrenches, assembly requires an adjustable wrench and a rubber mallet .
As you assemble the stepper, use the drawings below to identify the small parts used in assembly. The number
in parenthesis below each drawing refers to the key number of the part, from the PART LIST on page 18. The
second number refers to the quantity used in assembly. Note: Some small parts may have been pre-assem-
bled for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.
M8 Nylon
Locknut (28)–4
Console
Screw (57)–4
M10 x 25mm Button
Screw (29)–4
M8 x 35mm
Button Bolt (24)–4
M10 Nylon
Locknut (27)–4
M8 Split
Washer (54)–4
M10 x 75mm Button
Screw (92)–2
M10 x 82mm Button
Bolt (26)–4
M10 x 91mm Button
Screw (63)–2
M10 Split
Washer (30)–6
1. While another person lifts and holds the indicated end
of the Frame (1), attach the Front Stabilizer (95) to the
Frame with two M10 x 75mm Button Screws (92).
Make sure that the Front Stabilizer is turned so the
Wheels (67) are not touching the floor.
1
92
67
67
95
1
4
Page 5
2. While another person lifts and holds the indicated end
of the Frame (1), insert the Stabilizer (2) into the
Frame. Attach the Stabilizer with four M10 x 25mm
Button Screws (29) and four M10 Split Washers (30).
2
1
30
29
2
3. Slide one of the Pedal Brackets (13) onto the end of
the Right Pedal Leg (10). Align the lower hole in the
Pedal Bracket with the hole in the Lower Pedal Leg
(12). Insert an M10 x 82mm Button Bolt (26) into the
Pedal Bracket and the Lower Pedal Leg.
Next, align the upper hole in the Pedal Bracket (13)
with the hole in the Right Pedal Leg (10). Insert an
M10 x 82mm Button Bolt (26) into the Pedal Bracket
and the Right Pedal Leg. Tighten an M10 Nylon
Locknut (27) onto each of the Button Bolts.
Attach the other Pedal Bracket (13) in the same way.
4. While another person holds the Upright (3) near the
Frame (1), connect the Extension Wire Harness (77)
to the Wire Harness (39).
Gently pull the upper end of the Extension Wire
Harness (77) out of the top of the Upright (3) to
remove any slack. Then, carefully insert the Upright
into the Frame (1). Attach the Upright with two M10 x
91mm Button Screws (63) and two M10 Split Washers
(30).
3
10
12
27
4
13
13
Be careful
to avoid
pinching the
Wire Harnesses
(39, 77) during
this step.
3
26
77
39
1
30
63
5
Page 6
5. While another person holds the Left Handlebar (6) near
the Upright (3), Connect the Handgrip Pulse Wire (70)
to the Pulse Extension Wire (98). Insert the excess
wiring into the Left Handlebar.
Hold two Handlebar Bushings (66) around the rectangular tube on the left side of the Upright (3). Slide the
Left Handlebar (6) onto the Handlebar Bushings and
the tube on the Upright; be careful not to damage the
the Handgrip Pulse Wire (70) or the Pulse Extension
Wire (98). Attach the Left Handlebar with two M8 x
35mm Button Bolts (24), two M8 Split Washers (54),
and two M8 Nylon Locknuts (28); be careful not to
damage the Wires as you insert the Button Bolts.
Firmly tighten the Nylon Locknuts.
Attach the Right Handlebar (5) in the same way.
5
5
66
28
70
98
6
54
24
3
Be careful
to avoid
pinching the
Wires (70,
98) during
this step.
6. While another person holds the Console (4) near the
Upright (3), connect Extension Wire Harness (77), the
Pulse Extension Wire (98), and the ground wires to the
corresponding wires on the Console. Insert any slack
wire up into the Console and down into the Upright.
Attach the Console (4) to the Upright (3) with four
Console Screws (57). Make sure that the wires are
not pinched.
Snap the bookrack onto the Console (4) in the location
shown.
7. Make sure that all parts of the stepper are properly tightened. Note: Some hardware may be left over
after assembly is completed. To protect the floor or carpet from damage, place a mat under the stepper.
6
57
4
Bookrack
77
98
Console
Wires
Ground
Wires
3
Be careful to avoid
pinching the wires
during this step.
6
Page 7
INSTALLING THE RECEIVER FOR THE OPTIONAL CHEST PULSE SENSOR
If you purchase the optional chest pulse sensor (see page 15), follow the steps below to install the receiver
included with the chest pulse sensor.
1. Look under the Console (4) and locate the left water
bottle holder. Insert the tip of a flat-bladed screwdriver
between the side of the water bottle holder and the
Console in the location shown by arrow A. Gently pry
the indicated tab out of the small slot in the side of the
water bottle holder. Firmly push up on the bottom of the
water bottle holder until the tab remains outside of the
slot when the screwdriver is removed.
Next, insert the tip of the screwdriver between the
opposite side of the water bottle holder and the Console
(4) in the location shown by arrow B. Gently pry the side
of the water bottle holder away from the Console and
push the water bottle holder out of the Console.
Remove the right water bottle holder in the same way.
Next, locate the round audio cable jack. If there is a silver ring around the jack, remove the silver ring by turning it counterclockwise with the screwdriver.
2. Remove the four recessed screws (not shown) from the
underside of the Console (4). Do not remove the
screws attaching the Console to the Upright (3).
1
Ta b
4
B
Jack
2
A
Water
Bottle
Holder
Hold and lift here
Hold the fan and the top of the Console (4) in the locations shown at the right. Carefully lift the fan and the
top of the Console; do not let the fan slide out of the
top of the Console.
3. While another person holds the top of the Console (4)
and the fan in a vertical position, slide the receiver onto
the indicated plastic pin on the Console; make sure
that the receiver is oriented exactly as shown.
Locate the two small screws included with the chest
pulse sensor. Attach the receiver to the Console with
the two screws as shown.
Connect the wire on the receiver to the indicated wire
on the Console (4). Note: The other wires included with
the chest pulse sensor may be discarded.
4. Refer to step 2 above. Lower the top of the Console (4) and the fan. Make sure that no wires are pinched.
Reattach the top of the Console with the four screws removed in step 2. Refer to step 1 above. Press the
water bottle holders back into the Console. If you removed a silver ring from the audio cable jack, reattach
the silver ring.
3
3
4
4
Screws
Receiver
Pin
Wire
7
Page 8
HOW TO OPERATE THE STEPPER
Left Display
Note: If there is a sheet of clear plastic on the face of the console, remove it before using the console.
FEATURES OF THE CONSOLE
The advanced console offers a selection of features
designed to make your workouts more enjoyable and
effective. When the manual mode of the console is
selected, the stepping speed can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse sensor or the optional chest pulse sensor (see page 15).
The console also offers four preset workout programs.
Each program automatically changes the stepping
speed as it guides you through an effective workout.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included
audio cable, you can connect the stepper to your home
stereo, portable stereo, or computer and play special
iFIT.com CD programs (iFIT.com CD’s are available
separately). IFIT.com CD programs automatically control the stepping speed as a personal trainer coaches
you through every step of your workout. High-energy
music provides added motivation. Each CD features
two programs designed by certified personal trainers.
For information about the availability of iFIT.com
CD’s, call toll-free 1-800-735-0768.
Matrix
HOW TO EXERCISE ON THE STEPPER
Hold the handlebars and step onto
the pedals. Begin
stepping with a
smooth, continuous motion.
Because the pedals move independently of each
other, you must
maintain a continuous motion or both
pedals will sink to
the floor. Change
the stepping speed
(see step 3 on
page 9) until you
can comfortably
maintain a continuous motion.
As you step, you can exercise your upper leg muscles
by keeping your feet flat on the pedals. To focus on
your calf muscles, rise on your toes as you step.
Stand erect or lean forward slightly as you exercise.
Always keep your back straight to avoid injury.
Training Zone Bar
Handlebars
Pedals
With the stepper connected to your computer, you can
also go to our Web site and access programs directly
from the internet. Explore www.iFIT.com for details.
8
Page 9
HOW TO USE THE MANUAL MODE
Monitor your progress with the matrix, the
4
Training Zone bar, and the two displays.
Begin stepping to activate the console.
1
The stepper requires no batteries or external
power source. Power is supplied to the stepper by a generator while you are stepping. To
activate the console, begin stepping. After a few
seconds, the console displays will light. A tone
will then sound and the console will be ready for
use.
Select the manual mode.
2
When the power is
turned on, the
manual mode will
be selected. If you
have selected a
program or the
iFIT.com mode,
select the manual mode by pressing the Program
Select button repeatedly until a staircase appears
in the matrix and the indicator above the iFIT.com
button is not lit.
Begin stepping and change the stepping
3
speed as desired.
While you are
stepping, change
the stepping
speed by pressing
the Slower or
Faster button.
When the Slower
button is pressed, the resistance of the pedals
will increase and your stepping speed will
decrease; when the Faster button is pressed, the
resistance will decrease and you will have to
increase your stepping speed to prevent both
pedals from sinking to the floor. The stepping
speed can be decreased or increased in increments of 5 steps per minute. To change the stepping speed quickly, press one of the Steps Per
Minute buttons.
Note: After the Slower, Faster, or Steps Per
Minute buttons are pressed, it will take a moment
for the stepper to reach the selected setting.
Make sure to continue stepping while changing
the stepping speed.
The matrix—
When the manual
mode or the
iFIT.com mode is
selected, the matrix
will display a staircase. As you exercise, the indicators in the staircase will light, one
at a time, until the entire staircase is lit. This cycle
will then repeat.
The Training Zone
bar—The Training
Zone bar will show
the approximate
intensity level of
your exercise. For
example, if three or
four indicators in the bar are lit, the bar shows that
the intensity level is ideal for fat burning.
The left display—
The left display will
show the elapsed
time, the total number of steps you
have completed,
and the approximate number of vertical feet that you have
stepped. The display will change from one number
to the next every few seconds, as shown by the
indicators around the display. Note: When a program is selected, the display will show the time
remaining in the program and the time remaining
in the current segment of the program instead of
the elapsed time.
The right display—
The right display
will show your stepping speed and the
approximate numbers of fat calories
and calories you
have burned (see FAT BURNING on page 17).
The display will change from one number to the
next every few seconds, as shown by the indicators around the display. The display will also show
your heart rate when you use the handgrip pulse
sensor or the optional chest pulse sensor. Note:
Each time the stepping speed changes, the display will show the stepping speed.
9
Page 10
Measure your heart rate if desired.
Note: If you hold the handgrip pulse sensor
and wear the optional chest pulse sensor at
the same time, the console may not display
your heart rate accurately.
If there are
thin sheets of
plastic on the
metal contacts on the
handgrip
pulse sensor,
peel off the
plastic. To
measure your
heart rate,
hold the contacts; your palms must be resting on the upper
contacts, and your fingers must be touching the
lower contacts. Avoid moving your hands.
When your pulse
is detected, the
Heart Rate indicator above the right
display will begin
to flash, one or
two dashes (– –)
will appear in the right display, and then your heart
rate will be shown. For the most accurate heart
rate reading, hold the contacts for at least 15 seconds.
Note: If you continue to hold the pulse sensor, the
right display will show your heart rate for up to 30
seconds. The display will then show your heart
rate along with the other modes.
If your heart rate is not shown, make sure that
your hands are positioned as described. Be careful not to move your hands excessively or to
squeeze the metal contacts too tightly. For optimal performance, clean the metal contacts using
a soft cloth; never use alcohol, abrasives, or
chemicals.
Contacts
Turn on the fan if desired.
65
To turn on the fan at low speed, press the Fan
button. Pivot the fan to the desired angle. To turn
on the fan at high speed, press the Fan button a
second time. To turn off the fan, press the Fan
button a third time.
When you are finished exercising, the console
7
will automatically turn off.
If the pedals are not moved for several seconds, a
tone will sound, the console will pause, and the
left display will begin to flash.
If the pedals are not moved for about one minute,
the console will turn off, but the displays will not
be reset. If the pedals are not moved for about
five minutes, the console will turn off and the displays will be reset.
Note: The console features an information mode that
keeps track of the total number of hours that the stepper has been used and the total number of steps that
have been completed. To view this information, hold
down the Program
Select button for about
three seconds. The left
display will show the
total number of hours
that the stepper has
been used.
Press the iFIT.com button. The left display will
then show the total
number of steps completed, divided by 100.
For example, if the number 750 appears,
75,000 steps have been completed.
Press the Program Select button again to exit the
information mode.
10
Page 11
HOW TO USE PRESET WORKOUT PROGRAMS
Begin stepping to activate the console.
1
See step 1 on page 9.
Select one of the four workout programs.
2
When the power is
turned on, the
manual mode will
be selected. To
select a workout
program, press
the Program
Select button repeatedly until a “P 1,” “P 2,” “P 3,”
or “P 4” appears in the right display.
When a workout program is selected, the matrix
will show the first seven stepping speed settings
of the program. The left display will show how
long the program will last.
Begin stepping to start the program.
3
Each program is divided into several time segments of different lengths. (The left display will
show the time remaining in the program and the
time remaining in the current segment of the program.) One stepping speed is programmed for
each segment. (The same stepping speed may be
programmed for two or more consecutive segments.)
stepping speed setting for the second segment
will then be shown in the flashing Current
Segment column and the stepping speed will
automatically change.
Note: If all of the indicators in the Current Segment
column are lit after the stepping speed settings
have moved to the left, the settings will move
downward so that only the highest indicators
appear in the matrix.
The program will continue until the stepping
speed setting for the last segment is shown in the
Current Segment column of the matrix and no
time remains in the program.
Note: During the program, you can override the
stepping speed for the current segment, if
desired, by pressing the Steps Per Minute buttons. However, when the next segment begins,
the stepping speed will automatically change if a
different stepping speed is programmed for the
next segment. If you stop stepping for several
seconds, a tone will sound, the program will
pause, and the left display will begin to flash. To
restart the program, simply resume stepping.
Monitor your progress with the two displays.
4
See step 4 on page 9.
Measure your heart rate if desired.
5
See step 5 on page 10.
The stepping
speed setting for
the first segment
will be shown in
the flashing
Current Segment
column of the
matrix. The stepping speed settings for the next several segments
will be shown in the columns to the right.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, a
series of tones will sound, and all stepping speed
settings will move one column to the left. The
Current Segment
Turn on the fan if desired.
6
See step 6 on page 10.
When the program is finished, the console
7
will automatically turn off.
If the pedals are not moved for several seconds, a
tone will sound, the console will pause, and the
left display will begin to flash.
If the pedals are not moved for about one minute,
the console will turn off, but the displays will not
be reset. If the pedals are not moved for about
five minutes, the console will turn off and the displays will be reset.
11
Page 12
HOW TO CONNECT THE STEPPER TO YOUR
CD PLAYER OR COMPUTER
To use iFIT.com CD’s, the stepper must be connect-
ed to your portable CD player, portable stereo, home
stereo, or computer with CD player. See pages 12
and 13 for connecting instructions. To use iFIT.com
programs directly from our Web site, the stepper
must be connected to your home computer. See page
13 for connecting instructions.
HOW TO CONNECT YOUR PORTABLE STEREO
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the included adapter. Plug the
adapter into an AUDIO OUT jack on your stereo.
HOW TO CONNECT YOUR PORTABLE CD PLAYER
Note: If your CD player has separate LINE OUT
and PHONES jacks, see instruction A below. If
your CD player has only one jack, see instruction
B.
A. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the LINE OUT jack on your
CD player. Plug your headphones into the
PHONES jack.
A
LINE OUT
PHONES
LINE OUT
Audio
Cable
PHONES
Head-
phones
B. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your CD player. Plug your headphones into the other side of the Y-adapter.
B
PHONES
PHONES
A, B
AUDIO OUT
RIGHT
LEFT
Audio
Adapter
Cable
B. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the LINE OUT jack on your
stereo. Do not use the adapter.
C. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your stereo. Plug your headphones into the other side of the Y-adapter.
C
PHONES
Audio
Cable
3.5mm
Y-adapter
Headphones
Audio
Cable
Headphones
3.5mm
Y-adapter
12
Page 13
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the included adapter. Plug the
adapter into the LINE OUT jack on your stereo.
A
Audio
Cable
CD
VCR
Amp
LINE OUT
Adapter
LINE OUT
B. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the included adapter. Plug the
adapter into an RCA Y-adapter (available at electronics stores). Next, remove the wire that is currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
LINE OUT jack on your stereo.
B
CD
VCR
Amp
LINE OUT
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into the LINE OUT jack on your
computer.
A
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack
beneath the console of the stepper. Plug the other
end of the cable into a 3.5mm Y-adapter (available
at electronics stores). Plug the Y-adapter into the
PHONES jack on your computer. Plug your headphones or speakers into the other side of the Yadapter.
B
PHONES
Audio
Cable
3.5mm
Y-adapter
Audio
Cable
Adapter
Wire removed from
LINE OUT jack
Headphones/Speakers
RCA
Y-adapter
13
Page 14
HOW TO USE IFIT.COM CD PROGRAMS
To use iFIT.com CD programs, the stepper must be
connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See HOW
TO CONNECT THE STEPPER TO YOUR CD PLAYER OR COMPUTER on pages 12 and 13. For infor-
mation about the availability of iFIT.com CD’s, call
toll-free 1-800-735-0768.
Follow the steps below to use an iFIT.com CD
program.
Begin stepping to activate the console.
1
See step 1 on page 9.
The program will function in almost the same way
as a workout program (see step 3 on page 11).
However, an electronic “chirping” sound will alert
you when the stepping speed is about to change.
Note: If the stepping speed does not change
when a “chirp” is heard:
• Make sure that the indicator above the
iFIT.com button is lit.
• Adjust the volume of your CD player. If the
volume is too high or too low, the console
may not detect the program signals.
• Make sure that the audio cable is properly
connected and that it is fully plugged in.
Select the iFIT.com mode.
2
When the console is turned on,
the manual mode
will be selected.
To select the
iFIT.com mode,
press the
iFIT.com button. The indicator above the button
will light.
Insert an iFIT.com CD into your CD player and
3
press the play button.
A moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions.
Monitor your progress with the two displays.
4
See step 4 on page 9.
Measure your heart rate if desired.
5
See step 5 on page 10.
Turn on the fan if desired.
6
See step 6 on page 10.
When the program is finished, the console
7
will automatically turn off.
See step 7 on page 11.
14
Page 15
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
Our Web site at www.iFIT.com allows you to play
iFIT.com programs directly from the internet. To use
programs from our Web site, the stepper must be connected to your home computer. See HOW TO CONNECT YOUR COMPUTER on page 13. In addition,
you must have an internet connection and an internet
service provider. A list of specific system requirements
is found on our Web site.
Return to the stepper and begin stepping.
7
When the on-screen countdown ends, the program will begin. The program will function in
almost the same way as a workout program (see
step 3 on page 11). However, an electronic “chirping” sound will alert you when the stepping speed
is about to change.
Monitor your progress with the two displays.
8
See step 4 on page 9.
Follow the steps below to use a program from our
Web site.
Begin stepping to activate the console.
1
See step 1 on page 9.
Select the iFIT.com mode.
2
When the console
is turned on, the
manual mode will
be selected. To
select the iFIT.com
mode, press the
iFIT.com button.
The indicator above the button will light.
Go to your computer and start an internet
3
connection.
Start your Web browser, if necessary, and go
4
to our Web site at www.iFIT.com.
Follow the desired links on our Web site to
5
select a program.
Measure your heart rate if desired.
9
See step 5 on page 10.
Turn on the fan if desired.
10
See step 6 on page 10.
When you are finished exercising, the console
11
will automatically turn off.
See step 7 on page 11.
THE OPTIONAL CHEST PULSE SENSOR
The optional chest pulse sensor provides hands-free
operation and continuously monitors your heart rate
during your workouts. To purchase the optional
chest pulse sensor, call toll-free 1-800-734-2377.
Read and follow the on-line instructions for using
a program.
Follow the on-line instructions to start the
6
program.
When you start the program, an on-screen countdown will begin.
15
Page 16
TROUBLESHOOTING AND MAINTENANCE
Inspect and tighten all parts of the stepper regularly.
The stepper can be cleaned with a soft cloth and a
small amount of mild, non-abrasive detergent. Keep
liquids away from the console.
HOW TO ADJUST THE REED SWITCH
For the console to display correct feedback, the pedals
must move at least five inches with each step. If the
console displays incorrect feedback when the pedals
are moved five inches or more, the Reed Switch (56)
should be adjusted.
8
65
26
64
13
52
32
56
46
Turn the Flywheel (46) until the Magnet (32) is aligned
with the Reed Switch (56) (refer to the inset drawing).
Loosen the indicated Screw (52). Slide the Reed
Switch slightly closer to the Flywheel, and retighten
the Screw. Make sure that the Magnet will not hit
the Reed Switch when the Flywheel turns. Repeat
until the console displays correct feedback.
Carefully slide the Right Side Shield (8) back onto the
stepper. Reattach the three M4 x 38mm Screws (64)
and the two M4 x 25mm Screws (65). Reattach the
Pedal Bracket (13).
Remove the right Pedal Bracket (13) by removing the
two M10 x 82mm Button Bolts (26) and the two M10
Nylon Locknuts (not shown). Then, remove the two M4
x 38mm Screws (64) and the three M4 x 25mm Screws
(65). Carefully slide the Right Side Shield (8) off the
stepper.
HOW TO LEVEL THE STEPPER
If the stepper rocks
slightly during use,
turn one or both of
the Feet (15) under
the Stabilizer (2) until
the stepper is level.
2
15
16
Page 17
EXERCISE GUIDELINES
Fat Burning
WARNING:
• Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the
age of 35 or individuals with pre-existing
health problems.
• The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determining heart rate trends in general.
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition and
adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning, maximum fat burning, and cardiovascular (aerobic) exercise.
To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy. If
your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest number or the middle number in your training zone as you
exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the intensity of your exercise until your heart
rate is near the highest number in your training zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in preparation for exercise.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age; the three numbers are your “training zone.”
The lowest number is the recommended heart rate for
fat burning; the middle number is the recommended
heart rate for maximum fat burning; and the highest
number is the heart rate for aerobic exercise.
Training zone exercise, consisting of 20 to 30 minutes of exercising with your heart rate in your training
zone. (During the first few weeks of your exercise program, do not keep your heart rate in your training
zone for longer than 20 minutes.)
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three workouts each week, with at least one day of rest between
workouts. After a few months of regular exercise, you
may complete up to five workouts each week, if
desired. The key to success is make exercise a regular and enjoyable part of your everyday life.
17
Page 18
69 2 M8 x 22mm Button Bolt
70 2 Handgrip Pulse Sensor/Wire
71 4 M6 x 22mm Flat Head Screw
72 1 Pulley Axle
73 1 Pulley
74 8 M8 x 68mm Bolt
75 2 Front Axle Mount
76 2 Front Belt Gear
77 1 Extension Wire Harness
35 2 Bumper
36 2 Spring Pulley
37 4 M6 Washer
38 1 Adjustment Cable
39 1 Wire Harness/Adjustment Motor
40 2 Belt/Spring Assembly
41 1 Stop Bolt
42 1 Eye Bolt
43 3 M6 Nut
78 2 Retaining Washer
79 2 Rear Gear Washer
80 4 Plastic Retainer
81 2 Belt Pulley
44 1 Flywheel Washer
45 1 Generator Axle
46 1 Flywheel
47 2 Front Gear Washer
82 6 M6 x 12mm Button Screw
83 4 Delrin Spacer
84 1 Belt Pulley Axle
85 1 Generator
86 4 M8 x 14mm Button Screw
87 1 Control Bracket
88 4 Offset
89 1 Control Board
90 2 Handlebar Endcap
48 1 Generator Belt
49 1 “C” Magnet
50 1 Return Spring
51 1 Idler Arm
52 12 M4 x 10mm Screw
53 1 “J” Bolt
54 4 M8 Split Washer
55 2 Lower Pedal Leg Weld Spacer
56 1 Reed Switch/Wire
91 2 M6 x 72mm Button Bolt
92 2 M10 x 75mm Button Screw
93 6 M6 Nylon Locknut
94 2 Front Stabilizer Endcap
95 1 Front Stabilizer
96 4 M8 x 33mm Button Bolt
57 4 Console Screw
58 1 Reed Switch Bracket
59 1 Mounting Bracket
60 2 M6 x 15mm Button Screw
61 2 Upper Pedal Leg Weld Spacer
62 1 M8 x 48mm Bolt
# 1 User’s Manual
97 1 Flywheel Spacer
98 1 Pulse Extension Wire
63 2 M10 x 91mm Button Screw
64 4 M4 x 38mm Screw
65 6 M4 x 25mm Screw
# 1 Allen Wrench
66 4 Handlebar Bushing
67 2 Wheel
68 2 Foam Grip
Key No. Qty. Description Key No. Qty. Description Key No. Qty. Description
PART LIST—Model No. NTM58020 R0103A
1 1 Frame
2 1 Stabilizer
3 1 Upright
4 1 Console
5 1 Right Handlebar
6 1 Left Handlebar
7 1 Left Side Shield
8 1 Right Side Shield
9 2 Pedals
11 1 Left Pedal Leg
10 1 Right Pedal Leg
12 2 Lower Pedal Leg
13 2 Pedal Bracket
14 2 Rear Stabilizer Endcap
15 2 Foot
16 2 20.8mm Snap Ring
17 4 31.8mm Bushing
18 8 19mm Bushing
19 2 23mm Snap Ring
18
20 4 38.1 Bushing
21 4 Small Bumper
22 2 Belt Mount
23 2 Belt Bracket
24 4 M8 x 35mm Button Bolt
25 4 M8 x 26mm Button Screw
26 4 M10 x 82mm Button Bolt
27 5 M10 Nylon Locknut
28 24 M8 Nylon Locknut
29 5 M10 x 25mm Button Screw
30 6 M10 Split Washer
31 2 Rear Belt Gear
32 1 Magnet
33 2 Rear Axle Mount
34 1 M5 x 16mm Screw
Note: # indicates a non-illustrated part. Specifications are subject to change without notice.
Page 19
EXPLODED DRAWING—Model No. NTM58020 R0103A
69
82
76
74
74
25
74
74
47
73
90
83
4
25
78
80
28
80
98
93
28
9
26
28
28
83
81
78
93
76
28
52
75
75
47
21
31
18
82
26
79
81
90
10
19
77
74
20
71
72
28
82
13
83
52
68
33
5
28
28
74
74
27
61
71
28
66
33
22
96
84
83
16
31
23
79
70
94
28
18
28
82
54
24
57
42
44
65
12
66
17
67
66
43
91
55
41
30
32
28
8
63
46
43
67
57
49
30
92
86
3
66
64
97
50
60
37
45
34
93
86
24
54
62
93
52
48
14
15
64
7
59
85
28
56
52
58
91
6
70
82
29
37
95
65
36
27
28
1
37
51
35
60
39
94
53
37
38
35
36
88
82
61
30
52
89
17
30
2
17
29
12
16
29
69
55
25
25
88
18
9
96
87
52
20
52
21
18
23
22
21
20
19
18
40
14
15
13
27
28
26
18
11
40
19
Page 20
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-825-2588, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be
prepared to give the following information when calling:
• The MODEL NUMBER of the product (NTM58020)
• The NAME of the product (NordicTrack®MTN 740 stepper)
• The KEY NUMBER and DESCRIPTION of the part(s) (see page 18 of this manual)
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack®stepper (“Product”) is warranted to be free of all defects in material and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the product for one year after the date of purchase. Labor is covered for one year.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or component,
providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized service provider, or, at
our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, improper
assembly or installation, alterations, modifications without our written authorization or by failure on your part to use, operate, and
maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the Product as
specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of the defect; as
instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember to do
the periodic maintenance requirements specified in the Manual to assure proper operation and your continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them your
name and address and the serial number of your Product. They will tell you how to get a part replaced, or if necessary, arrange
for service where your Product is located or advise you how to ship the Product for service. Before shipping, always obtain a
Return Authorization Number (RA No.) from our Customer Service Department; securely pack your Product (save the original
shipping carton if possible); put the RA No. on the outside of the carton and insure the product. Include a letter explaining the
product or problem and a copy of your proof of purchase if you believe the service is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or
performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of
enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow
the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty. This warranty gives you specific legal rights
and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 190010 R0103A Printed in China © 2003 ICON Health & Fitness, Inc.
Loading...