Nokia 2110i, 2110 DIGITAL PCMCIA CARD 2

After Sales Technical Documentation

DIGITAL PCMCIA CARD

DTP–2

Original 12/97

Copyright  1997 Nokia Mobile Phones. All rights reserved.

Digital PCMCIA Data Card

After Sales

DTP–2

Contents of Digital PCMCIA Card DTP–2

Digital PCMCIA Card DTP–2 Page 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DTP–2 ver II Page 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Software update for DTP–2 ver II Page 3. . . . . . . . . . . . . . . . . . . . .

Procedure: Page 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Programming tools Page 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

DTP–2 Page 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Software update for DTP–2 Page 5. . . . . . . . . . . . . . . . . . . . . . . . . .

Procedure: Page 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Programming tools Page 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Technical Documentation

Page 2

Original 12/97

After Sales

Digital PCMCIA Data Card

Technical Documentation

Digital PCMCIA Card DTP–2
DTP–2 ver II

The Cellular Data Card enables the use of advanced communication functions
with the help of compatible cellular phone. The GSM/PCN handportable sup­ports data and PC fax transmission. The feature is based on Nokia’s PCMCIA
standard data card installed in a laptop computer and connected to the hand­portable telephone with a simple connection cable.

DTP–2

Data services: 300...9600 (except 1200 / 75) bit/s async data

automatic fax teleservice
short message data service (SMS)
access to packet network

NOKIA Cellular Data Card has low power consumption, it offers ECM for faxes,
V.42 bis non–transparent data compression, ISDN CAPI support.

Unit/type: Product code:
PCMCIA Card DTP–2 ver II 0750091

Data Cable DLM–1 0730086
Setupkit for Data Card DLH–5 0630081
Setupkit Diskette DLH–5 0630082
User Guide, Digital PC Card DTP–2C eng. 9357032
User Guide, Digital PC Card DTP–2C intl 9357041

Software update for DTP–2 ver II

Note:

II is needed. This drive has been tested and found suitable for updating the

Original 12/97

You need a desktop PC with an external PCMCIA drive. Also CardShark

Page 3

Digital PCMCIA Data Card

After Sales

DTP–2

Procedure:

Technical Documentation

Cellular Data Card. NMP does not sell this drive, you need to purchase it local­ly.

(If a PC with PCMCIA slot is used, difficulties might occur. Minimum require­ment is therefore that the PC is equipped with Intel 82363 compatible PCIC.)

1. Copy the Update SW and Flash SW files from floppy disk to the PC hard
disk, recommended directory is : C:\dtp2v2

2. Check the current flash SW version before updating (Command ATI2).

3. Note that the old data card DTP–2 can not be run with these software pro­grams designed for DTP–2 ver II card (code 0750091).

4. Running the update SW in pure DOS–mode (instead of Windows DOS–
prompt) is recommended.

5. If you have the line ”DEVICE=EMM386...” in your PC’s CONFIG.SYS, make
sure that line has the option X=D000–DFFF (or at least that area excluded)

6. It is possible to run the update program even, if some PCMCIA driver SW is
active. If the update program doesn’t seem to work, you can try disabling the­PCMCIA driver SW. If PCMCIA driver SW is used, you must take the card out
from PC after programming, and plug it in again before it works normally.

7. If you use the card straight after SW update, it must be first taken out from
PCMCIA slot and then reinserted in order for the PCMCIA driver SW to recog­nize it.

8. Start the Update SW with the command: UPDATE –DTP2CN01.05F (ac­cording to the latest sw version)

Programming tools

Unit/type: Product code:
DTP–2 ver II Flash (MCU) Software, 3.5” disk 0775070

DTP–2 ver II Service SW , 3,5” disk 0774058

The service SW disk includes also the upgrading SW.
File names: update.exe and cardtest.exe

Page 4

Original 12/97

After Sales

Digital PCMCIA Data Card

Technical Documentation

DTP–2

Cellular Data Card is intended to link the portable computer and the cellular
phone together for sending and receiving data files, receiving and transmitting
faxes and accessing the short message service (SMS) provided by the digital
cellular network and cellular phone.

Data services: 300...9600 (except 1200/75) bit/s async data

Dimensions (h x w x d): 54 x 85.6 x 5 mm

Unit/type: Product code: Module code:
PCMCIA card DTP–2 0750029

• interface module DP1 0200272

DTP–2

automatic fax teleservice
short message data service (SMS)
access to packet network

Software update for DTP–2

There are available programming tools for updating DTP–2 Cellular Data Card
software. They include a programming diskette and a programming connector.

Note:

CardShark II PCCS2–E is needed. This drive has been tested and found suit­able for updating the Cellular Data Card. NMP does not sell this drive, you need
to purchase it locally.

(If a PC with PCMCIA slot is used, difficulties might occur. Minimum require­ment is therefore that the PC is equipped with Intel 82363 compatible PCIC.)

Procedure:

The programming diskette is a bootable diskette, it updates the card automati­cally when you boot the computer with the diskette inserted.

To update cards, follow the instruction below.

1. Insert the programming diskette to the diskette drive of your computer.

2. Insert the Cellular Data Card you want to program to the slot A of your Card­Shark and connect the programming connector to the end of the card.

In addition, you need a desktop PC with an external PCMCIA drive. Also

3. Turn to power on to your computer. The programming software will start the
programming automatically.

Original 12/97

Page 5

Digital PCMCIA Data Card

After Sales

DTP–2

4. After the card has been programmed, the software will ask: ”Do you want to
program more cards (Y/N) ?” Choose Y if you want to update another card and
N if you want to exit the program.

5. When you exit the software, remove the programming diskette from the dis­kette drive and the programming connector from the card and reboot your com­puter.

Programming tools

Unit/type: Product code:
DKH–4P Programming adapter DTP–2 0694034

DTP–2 SW (Flash software) Diskette, 3.5” disk 0775025

Technical Documentation

Page 6

Original 12/97