Nissan Z ROADSTER 2007, Z COUPE 2007, NISMO Z 2007 USER Manual

QU ICK RE FE R E N CE G U I DE

2007 350Z

Sh if t_obsession

INSTRUMENT BRIG HTNESS

CONTROL*

TRIP COMPUTER MODE/

SETTING BUTTONS

*See your Owner’s Manual fpr more information.

HEADLIG HT AND TURN

SIGNAL CONTROL

STEERING WHEEL

SWITCH FOR AUDIO CONTROL

CRUISE CONTROL

WINDSHIELD WIPER/

WASHER SWITCH

SOFT TOP

OPERATING SWITCH (Roadster Models)

TCS/VDC

OFF SWITCH

FUEL-FILLER

DOOR RELEASE

HOOD RELEASE*

STEERING WHEEL

TILT ADJUSTMENT*

CONTROL PANEL

DIS PLAY

AUDIO SYSTEM

CLIMATE CONTROLS

HEADLIGHT AND TURN SIGNAL CONTROL

HEADLIGHT SWITCH

 Turn the headlight switch to the position to turn

on the front parking, side marker, tail, license plate and instrument panel lights.

 Turn the headlight switch to the position to turn on

the headlights. All other lights remain on.

HIGH BEAM

 Push the headlight switch forward to select the high beam function. The blue

indicator light illuminates. Pull the headlight switch back to the original position to select the low beam. The blue indicator light goes off.

 Pull and release the headlight switch to flash the headlight high beams on and off.

TURN SIGNAL SWITCH

 Move the headlight control switch up or down to signal the turning direction.

When the turn is completed, the turn signals cancel automatically.

 To signal a lane change, move the headlight control switch up or down to the

point where the indicator light begins to flash, but the headlight control switch does not latch.

WINDSHIELD WIPER/WASHER SWITCH

 The ignition switch must be in the ON position

to activate the windshield wipers.

 Move the lever to the following positions to

operate the windshield wipers:

Intermittent (INT) – Front wipers operate intermittently and can be further adjusted

by twisting the time control ring

Low Speed (LO) – Continuous low-speed operation of front wipers.

High Speed (HI) – Continuous high-speed

operation of front wipers.

Mist (MIST) – Lift the lever up for one sweep of the front wipers.

Rear Wipers (REAR) – Twist the end section to operate the first (INT) or second (ON) speed settings for the rear wipers.

 The washer function activates the washer fluid and several sweeps of the wipers:

• For F

RONT WASHER, pull lever toward you

• For REAR WASHER, push lever away from you. (Coupe only)

TRIP COMPUTER

The trip computer may be used to check items such as speed, outside air temperature, distance to empty (fuel), average mileage and speed, elapsed time and distance traveled. Additionally, it can function as a stopwatch or be used to operate the RPM shift feature (REV) (Manual transmission only).

To operate the Trip Computer:

Turn the ignition switch on. Then press the side of the buttons.

 Press the button 01 toward the left to scroll through

each mode.

Press the button 02 toward the left to reset or adjust



the various mode selections.

RPM SHIFT INDICATOR (Manual transmission only)

The engine RPM shift indicator light (REV) is located in the tachometer. During driving, it indicates ‘shift point’, or time to up-shift.

 The shift indicator light will begin flashing about

500 RPM before a pre-set engine RPM is reached in any gear. Then, when the actual pre-set RPM is reached, the shift indicator light will stop flashing and remain on.

 The engine RPM shift point may be set by the driver using the Trip Computer

display. Or it may be deactivated, also using the Trip Computer display.

TIRE PRESSURE MONITORING SYSTEM (TPMS)

This system monitors tire pressure. If the low tire pressure warning light illuminates, check the tire pressure in all four tires.

Adjust the low tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label located in the driver’s door opening. After tire pressures are adjusted, the vehicle will need to be driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light.

CRUISE CONTROL (if so equipped)

 To activate the cruise control, push the ON.OFF switch.

The indicator light in the instrument panel will illuminate.

 To set cruising speed, accelerate the vehicle to the

desired speed, push the COAST/SET switch and release it. The SET indicator light in the instrument panel will illuminate.



To reset at a faster cruising speed, push and hold the ACCEL/RES switch. When the vehicle reaches the speed you desire, release the switch.

 To reset at a slower cruising speed, push and hold the COAST/SET switch. Release

the switch when the vehicle slows to the desired speed.

 To cancel cruise control, push the CANCEL switch or tap the brake pedal. The SET

indicator light in the instrument panel will go out.

 To resume a preset speed, push and release the ACCEL/RES switch. The vehicle

returns to the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).

 To turn off cruise control, push the ON.OFF switch. Both the CRUISE indicator light

and the SET indicator light in the instrument panel will go out.

STEERING WHEEL SWITCHES FOR AUDIO CONTROL (if so equipped)

 With the ignition switch turned to the ACC or ON

position, push the PWR (Power) on/off switch to turn the audio system on or off.

 Push the MODE select switch to change the mode.

• Without satellite radio: AM, FM1, FM2, and CD or CD changer.

• With satellite radio: AM, FM1, FM2, SAT1, SAT2 and CD changer.

 The SEEK switch can be used to perform the following:

• Radio memory change – Push the change the radio frequency.

• Radio tuning – Push and hold the seek the next or previous radio station.

• CD track change – Push the beginning of a CD track or skip to the next track.

• CD disc change – Push and hold the

change the playing disc.

• MP3 folder change – Push and hold the

< >

switch for less than 1.5 seconds to

< >

switch for more than 1.5 seconds to

< >

switch for less than 1.5 seconds to return to the

< >

switch for more than 1.5 seconds to

< >

switch up or down for more than 1.5

seconds to change the folders (if folders exist).

+ 9 hidden pages