Nissan Z COUPE 2014 08IT Navigation Manual

®

2014 NAVIGATION

SYSTEM

OWNER’S MANUAL

For your safety, read carefully and keep in this vehicle.

FOREWORD

NISSAN NAVIGATION SYSTEM HELP­DESK CONTACT INFORMATION

For assistance or inquiries about the NISSAN
Navigation System, or to order updated map
data, contact the NISSAN NAVIGATION SYS­TEM HELPDESK at:

ADDRESS: P.O. Box 1588,

•

Orem, UT 84059-992

E-MAIL: [e-mail]

•

WEB SITE: www.NissanNavigation.com or

•

www.nissan.ca

PHONE: [phone]

•

HOURS: 6:00 AM to 5:00 PM

•

(Pacifi c Time)

NISSAN CONSUMER AFFAIRS DE­PARTMENT

For assistance or inquiries about the NISSAN
warranty, service or general questions, contact
the NISSAN Consumer Affairs Department at:

For U.S. customers
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003
1-800-NISSAN-1
(1-800-647-7261)

For Canadian customers
Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario L4W 4Z5
1-800-387-0122

Thank you for purchasing a NISSAN vehicle.

This user’s manual is for the navigation system
only. This manual contains operating instructions
for the NISSAN Navigation System offered in
your NISSAN vehicle.

Please read this manual carefully to ensure safe
operation of the navigation system.

Because of possible specifi cation changes

•

and optional equipment, sections of this
manual may not apply to your vehicle.

All information, specifi cations and illustra-

•

tions in this manual are those in effect at the
time of printing. NISSAN reserves the right to
change specifi cations or design at any time
without notice.

Do not remove this manual from the vehicle

•

when selling this vehicle. The next user of this
navigation system may need the manual.

FOREWORD

NISSAN NAVIGATION SYSTEM HELP­DESK CONTACT INFORMATION

For assistance or inquiries about the NISSAN
Navigation System, or to order updated map
data, contact the NISSAN NAVIGATION SYS­TEM HELPDESK at:

. ADDRESS: P.O. Box 1588, Orem, UT

84059-992

. E-MAIL: [e-mail]

. WEB SITE: www.NissanNavigation.com or

www.nissan.ca

. PHONE: [phone]

. HOURS: 6:00 AM to 5:00 PM (Pacific

Time)

NISSAN CONSUMER AFFAIRS DE­PARTMENT

For assistance or inquiries about the NISSAN
warranty, service or general questions, contact
the NISSAN Consumer Affairs Department at:

For U.S. customers
Nissan North America, Inc.
Consumer Affairs Department
P.O. Box 685003
Franklin, TN 37068-5003

1-800-NISSAN-1
(1-800-647-7261)
For Canadian customers
Nissan Canada Inc.
5290 Orbitor Drive
Mississauga, Ontario L4W 4Z5
1-800-387-0122

Thank you for purchasing a NISSAN vehicle.
This user’s manual is for the navigation system

only. This manual contains operating instructions
for the NISSAN Navigation System offered in
your NISSAN vehicle.

Please read this manual carefully to ensure safe
operation of the navigation system.

. Because of possible specification changes

and optional equipment, sections of this
manual may not apply to your vehicle.

. All information, specifications and illustra-

tions in this manual are those in effect at the
time of printing. NISSAN reserves the right
to change specifications or design at any
time without notice.

. Do not remove this manual from the vehicle

when selling this vehicle. The next user of
this navigation system may need the manual.

Contents

Introduction

1

Getting started

Map settings

Setting destination

Route guidance

Storing location/route

Viewing technical information

Other settings

Voice recognition

General system information

Troubleshooting guide

Index

2

3

4

5

6

7

8

9

10

11

12

1 Introduction

How to use this manual .......................................................... 1-2

For safe operation ............................................................... 1-2

Reference symbols ............................................................. 1-2

Safety information ..................................................................... 1-2

Laser product ............................................................................ 1-3

HOW TO USE THIS MANUAL SAFETY INFORMATION

This manual uses special words, symbols and
icons that are organized by function.

Please refer to the following items to understand
how to use this manual properly.

FOR SAFE OPERATION

WARNING

Indicates the presence of a hazard that
could cause death or serious personal
injury. To avoid or reduce the risk, the
procedures must be followed precisely.

CAUTION

Indicates the presence of a hazard that
could cause minor or moderate perso­nal injury or damage to your vehicle. To
avoid or reduce the risk, the procedures
must be followed carefully.

NOTE:

Indicates items that help you understand
and maximize the performance of your
vehicle. If ignored, they may lead to a
malfunction or poor performance.

REFERENCE SYMBOLS

INFO:

Indicates information that is necessary for
efficient use of your vehicle or accessories.

Reference page:

Indicates the title and page that you should refer
to.

<>:
Indicates a button on the control panel.
[]:
Indicates a key/item displayed on the screen.

Voice Command:
Indicates an operation by voice command.
Variable commands, such as numbers, are

indicated in

italics

in parentheses < >.

1-2 Introduction

This system is primarily designed to help you
reach your destination, and it also performs
other functions as outlined in this manual.
However, you, the driver, must use the system
safely and properly. Information concerning road
conditions, traffic signs and the availability of
services may not always be up to date. The
system is not a substitute for safe, proper and
legal driving.

Before using the navigation system, please read
the following safety information. Always use the
system as outlined in this manual.

WARNING

. To operate the navigation system or

use the multi-function controller,
first park the vehicle in a safe
location and set the parking brake.
Operating the system while driving
can distract the driver and may
result in a serious accident.

. Do not rely on route guidance alone.

Always be sure that all driving
maneuvers are legal and safe in
order to avoid accidents.

. Do not disassemble or modify this

system. If you do, it may result in
accidents, fire or electrical shock.

LASER PRODUCT

. If you notice any foreign objects in

the system hardware, spill liquid on
the system or notice smoke or a
smell coming from it, stop using the
system immediately and contact a
NISSAN dealer. Ignoring such con­ditions may lead to accidents, fire or
electrical shock.

CAUTION

. Do not use this system if you notice

any malfunctions such as a frozen
screen or the lack of sound. Con­tinued use of the system may result
in accidents, fire or electrical shock.

. Some states/provinces may have

laws limiting the use of video
screens while driving. Use this sys­tem only where it is legal to do so.

. Extreme temperature conditions

[below −48F(−208C) and above
1588F (708C)] could affect the per­formance of the system.

. The glass display screen may break

if it is hit with a hard or sharp object.
If the glass screen breaks, do not

touch it. Doing so could result in an

injury.

NOTE:

Do not keep the navigation system running
with the engine or the hybrid system
stopped. Doing so may discharge the
vehicle battery (12V battery) . When you
use the navigation system, always keep
the engine or the hybrid system running.

This navigation system is certified as a Class 1
laser product.

The navigation system complies with DHHS
Rules 21 CFR Chapter 1, Subchapter J.

WARNING

. Do not disassemble or modify this

system. There are no user service­able parts in this navigation system.

. If maintenance, adjustments and

operations other than those speci­fied in this manual are attempted,
injury due to laser radiation and
exposure could occur.

Required SiriusXM Satellite Radio and NavTraf­fic monthly subscriptions are sold separately.
NavTraffic are only available in select markets.
For more information,

see www.siriusxm.com/navtraffic.

Introduction 1-3

Required SiriusXM Satellite Radio and Nav-

WeatherXM monthly subscriptions are sold
separately. NavWeatherXM is only available in
select markets. For more information,

see www.siriusxm.com/navweather.

1-4 Introduction

2 Getting started

Control buttons and functions ............................................... 2-2

Control panel ........................................................................ 2-2

Multi-function controller ................................................... 2-5

Steering wheel switch ....................................................... 2-5

Starting the system ................................................................... 2-7

Navigation system status screen .......................................... 2-7

Functions disabled while driving ........................................... 2-8

Menu screen and how to operate ..................................... 2-10

Menu screens and their purposes ............................... 2-10

Using controls to adjust values, levels, etc. .............. 2-11

Start menu ......................................................................... 2-12

List screen ......................................................................... 2-13

Touch panel operation .......................................................... 2-14

Example of touch panel operation ............................... 2-14

How to input letters and numbers ..................................... 2-15

Character (letters and numbers) input screen ......... 2-15

Number input screen ....................................................... 2-16

Map menu screen ................................................................. 2-17

Current location map screen ...................................... 2-17

Scrolled location map screen ..................................... 2-18

Storing home location/address .......................................... 2-18

How to store home location ....................................... 2-18

Setting destination ................................................................ 2-20

Searching for destination ............................................. 2-20

Starting route guidance ................................................ 2-21

Canceling route .............................................................. 2-21

Operating maps ..................................................................... 2-22

How to view map screen ............................................. 2-22

Setting voice guidance ........................................................ 2-23

Turning voice guidance ON/OFF ............................... 2-23

Adjusting voice guidance volume .............................. 2-24

NISSAN voice recognition .................................................. 2-25

Using the system ........................................................... 2-25

Before starting ................................................................ 2-25

Giving voice commands ............................................... 2-25

Command list .................................................................. 2-27

CONTROL BUTTONS AND

FUNCTIONS

CONTROL PANEL

Type A

Type B

2-2 Getting started

Type C

Type D

Getting started 2-3

Type E

1

<STATUS>:

*

Push multiple times to display audio in­formation with either the air conditioner
status, fuel economy or navigation direc­tions.

2

<DEST>:

*

Push to enter a destination. Various meth­ods for entering a destination are available.

“4. Setting destination”

3

<ROUTE>:

*

Push to access guidance control functions
(guidance cancellation, route priority, way­point setting on the route, etc.).

4

Multi-function controller:

*

Turn to highlight an item on the screen,
push to select the highlighted item or scroll
the map.

5

<INFO>:

*

Push to display the vehicle, traffic, weather
or voice recognition information.

6

<DAY/NIGHT OFF> :

*

Push to switch between the day screen
(bright) and the night screen (dark). Push
and hold to turn off the display. Push again
to turn on the display.

7

<SETTING>:

*

Push to access the system settings.

8

<VOICE>:

*

Push to hear the current guidance for a
programmed route.

9

<BACK>:

*

Push to return to the previous screen. In a
settings screen, this button can also be
used to apply the setting.

2-4 Getting started

In a character input screen, this button can
also delete the characters that have been
entered.

10

<MAP>:

*

Push to display the map. While following
programmed route, push multiple times to
change the type of route information.

11

<ZOOM IN>, <ZOOM OUT>:

*

Push to switch to the zoom mode to
change the map scale.

12

<DISP>/<DISPLAY>:

*

Push to access the display settings.

INFO:

. If <BACK> needs to be pushed to apply

the setting on a settings screen, this manual
will explicitly include a step for this proce­dure. Otherwise, pushing <BACK> returns
the display to the previous screen.

. The layout of the control panel switches may

vary depending on the vehicle model and
equipment.

MULTI-FUNCTION CONTROLLER

With Directional buttons

1

<ENTER>:

*

Push to select the highlighted item on the
screen.

If this button is pushed while a map is
displayed, the map menu screen is dis­played.

2

Main directional buttons:

*

Use to move across the map, highlight an
item on the screen or adjust a setting
(volume, brightness, etc.).

3

Additional directional buttons:

*

Use to move across the map or highlight an
item on the character input screen.

4

Center dial:

*

Turn to highlight an item on the screen or
adjust a setting.

Turn the center dial on the map screen. The
map scale is displayed. Use the center dial
to adjust the map scale.

Without Directional buttons

1

<ENTER>:

*

Push to select the highlighted item on the
screen.

If this button is pushed while a map is
displayed, the map menu screen is dis­played.

2

Center dial/Slide switch:

*

Center dial
Turn to highlight an item on the screen or

adjust a setting.

The center dial can also be used to adjust
the map scale.

Slide switch
Slide (push upward/downward/leftward/

rightward) to select an item on the screen
or to adjust a setting (volume, brightness,
etc.)

The map can be scrolled in 8 directions by
sliding this switch.

STEERING WHEEL SWITCH

Type A

Getting started 2-5

played.

“Map menu screen” (page 2-17)

Push and hold while a map or status screen
is shown to display the Start Menu.

“Start menu” (page 2-12)

If this button is tilted up while the audio
function is activated and the map or status
screen is displayed, the audio system can
be operated.

2

< >:

Type B

Type C

1

<ENTER>:

*

Tilt to highlight an item on the screen or
adjust a setting. Push to select the high­lighted item.

If this button is pushed while a map is
displayed, the map menu screen is dis-

*

Push this button during a setting operation
to return to the previous screen. In a
settings screen, this button can also be
used to apply the setting.

3

<− +>:

*

Use to adjust the volume. These buttons
have the same function as that of the
volume control knob. Refer to the vehicle
Owner’s Manual.

4

<TALK >:

*

Push to start the voice recognition mode. If
the voice recognition mode is already
activated, pushing this button cancels the
voice guidance and you can speak a voice
command immediately.

5

< >:

*

Push to display the phone mode screen.
Refer to the vehicle Owner’s Manual.

2-6 Getting started

6

<SOURCE> :

*

Use to switch the audio mode (source).
Refer to the vehicle Owner’s Manual.

7

< >:

*

Push to change what is shown on the
vehicle information display.

Refer to the vehicle Owner’s Manual.

STARTING THE SYSTEM

The navigation system starts when the ignition
switch is placed in the ACC or ON position.

NOTE:

Do not keep the navigation system on with
the engine or the hybrid system stopped.
Doing so may discharge the vehicle battery
(12V battery) . When you use the navigation
system, always keep the engine or the
hybrid system running.

NAVIGATION SYSTEM STATUS
SCREEN

By pushing <STATUS> at anytime, you can
display a split screen with audio information that
is always at the top. Each time <STATUS> is
pushed, the bottom part of the screen changes
between air conditioner, fuel economy or navi­gation directions.

INFO:

There are different status screens displayed
depending on various factors, such as the
currently active mode, whether a destination
has been set or not, etc.

When a route to the destination is set and the
audio system is on, a screen similar to the one
above appears.

1

Turning direction at the next intersection

*

2

Name of the next street

*

3

Distance to the next intersection

*

4

Distance remaining to the destination

*

5

Remaining time to the destination

*

When a route to the destination is not set and
the audio system is off, a screen similar to the
one above appears.

Getting started 2-7

FUNCTIONS DISABLED WHILE

DRIVING

To ensure safe driving, some functions cannot
be operated or have limited operation when the
vehicle driving speed is above 5 MPH (8 km/h).

The on-screen text and keys for these restricted
functions will be "grayed-out" or muted and
cannot be selected while driving. In some cases,
a screen message will appear indicating a
restricted function.

Restricted functions while driving include:

. Character (letter and number) input screen

during destination entry (street address,
phone number, freeway entrance/exit, inter­section, city center)

. Places search by name and city name

. Scrolling and viewing of certain navigation

lists

. Adding/editing address book entries

. Adding/editing home location

. Storing current position, information, desti-

nations

These functions will become available again
when the vehicle speed is reduced to 5 MPH (8
km/h).

Destination functions available while driving
include:

2-8 Getting started

. Home

. Address Book

. Previous Destinations

. Nearby places

. Address book

. My places

. Map input

Getting started 2-9

MENU SCREEN AND HOW TO

OPERATE

MENU SCREENS AND THEIR PUR­POSES

Push <DEST>, <ROUTE>, <INFO>,
<SETTING> or <PHONE> (if so equipped)
to display the corresponding menu screen.

How to select a menu item

Example: <DEST> screen

1. Highlight the preferred menu item using the
multi-function controller.

2. To select the preferred menu item, highlight
the item and push <ENTER>. The next
screen is displayed.

2-10 Getting started

3. Push <BACK> to return to the previous
screen without applying any changes.

Push <MAP> to return to the current
location map screen without applying any
changes.

INFO:

An item can also be selected by tilting
<ENTER> on the steering wheel up and down.

USING CONTROLS TO ADJUST VALUES, LEVELS, ETC.

With directional buttons

Getting started 2-11

. These same adjustments can also be

performed using the touch panel operation.

“Adjusting volume and others”
(page 2-14)

START MENU

The start menu can be displayed using the
steering wheel switch.

Without directional buttons

There are five main methods to control the
navigation system: the center dial, the main
directional buttons, the slide switch, the touch
panel and the switches on the steering wheel.
Use these controls to adjust the volume of the
phone and voice guidance, the display bright­ness, etc.

How to adjust

1. Highlight the preferred setting item and
push <ENTER>. The color of the corre­sponding adjustment item changes.

2. Adjust the value or level of the indicator bar
using the multi-function controller.

3. Push <ENTER> or <BACK> to apply the
setting.

INFO:

. The volume of phone and voice guidance,

the display brightness, etc. can be adjusted
by tilting <ENTER> on the steering wheel
up and down.

2-12 Getting started

1. Push and hold <ENTER> on the steering
wheel.

2. Highlight the preferred item and push

<ENTER>.

INFO:

<ENTER> on the steering wheel switch can be

used to display the start menu only when the
map or status screen is displayed.

Available items

. [Destination]:

Displays the destination screen. It is the
same screen that appears when <DEST> is
pushed.

“4. Setting destination”

. [Route]:

Displays the route screen. It is the same
screen that appears when <ROUTE> is
pushed.

“5. Route guidance”

. [Info]:

Displays the information screen. It is the
same screen that appears when <INFO> is
pushed.

“7. Viewing technical information”

. [Settings]:

Displays the settings screen. It is the same
screen that appears when <SETTING> is
pushed.

“8. Other settings”

LIST SCREEN

After searching for a point of interest, a list
screen is displayed.

Depending on the list displayed, it can be
sorted.

Items displayed in a list

1

Highlight the preferred item from the list

*

and push <ENTER> to select it. If a
location or facility name is not completely
displayed (due to length), highlight the item
to display the hidden part of the name.

2

Distance from the current location

*

3

Direction to the point of interest

*

4

If the entire list cannot be displayed on the

*

screen, the system displays the total
number of items in the list and the entry
number of the selected item. Scroll the list
using the multi-function controller.

5

An item that starts with the selected letter

*

will be displayed at the top of the list.

Getting started 2-13

6

Highlight and push <ENTER> to sort the

*

list in the original order.

7

When the list is sorted by the shortest

*

distance, the selected location can be
confirmed in the preview on the right side
of the screen.

8

Highlight and push <ENTER> to modify

*

search conditions.

TOUCH PANEL OPERATION

With this system, the same operations as those
for the multi-function controller are possible
using the touch panel operation.

This manual describes the operations using the
multi-function controller.

For the operations that differ from those of the
multi-function controller and for useful methods
for using the touch panel operation, refer to each
section.

EXAMPLE OF TOUCH PANEL OPERA­TION

Here, the operation examples performed with
the touch panel operation are described.

Selecting item

When the item is touched, the next screen is
displayed.

Adjusting volume and others

Touch [+] or [−] located on the right and left of
the bar graph to perform the adjustment.

Scrolling message or list

Touch [ ]or[ ] to scroll the message or list.
Touch [

]or[ ] to skip to the next page.

2-14 Getting started

HOW TO INPUT LETTERS AND
NUMBERS

Inputting letters and numbers

1. Touch the letter or number.

2. To delete a character, touch [Delete]. Push
and hold [Delete] to delete all of the
characters.

CHARACTER (letters and numbers) IN­PUT SCREEN

When setting a destination, searching for a
facility or editing the stored locations, etc.
alphanumeric characters must be entered into
the system.

1. Use the multi-function controller to highlight
a character on the displayed keyboard.

2. Push <ENTER>. The highlighted character
is entered.

3. Push <BACK>, or highlight [Delete] and
push <ENTER> to delete the last character
entered.

Push and hold <BACK> to delete all the
characters entered.

Highlight [Space] and push <ENTER> to
enter a space.

4. After finishing the entry, highlight [List] and
push <ENTER>.

Getting started 2-15

INFO:

. Push <BACK> on the control panel to

return to the previous screen, but only after
deleting all the characters entered.

. When [BACK] is touched on the screen, the

screen returns to the previous screen even
when characters have been entered.

. When text has been entered and the number

of matching list items has been narrowed
down enough so that they fit on the screen,
the list screen appears automatically.

Symbol input screen

INFO:

Symbol keys are displayed by highlighting
[Symbols] and pushing <ENTER>. Alphabet
keys are displayed by highlighting [A-Z] and
pushing <ENTER>.

NUMBER INPUT SCREEN

A phone number or a street number can also be
entered as a search method to look for a
destination.

INFO:

Only the locations included in the map data
database can be searched for by a phone
number.

1. Use the multi-function controller to highlight
a number on the displayed keyboard.

2. Push <ENTER>. The highlighted number is
entered.

3. Push <BACK>, or highlight [Delete] and
push <ENTER> to delete the last number
entered.

Push and hold <BACK> to delete all the
numbers entered.

4. After finishing the entry, highlight [List] and
push <ENTER>.

2-16 Getting started

MAP MENU SCREEN

INFO:

. <BACK> can be pushed on the control

panel to return to the previous screen, but
only after deleting all the numbers entered.

. When [BACK] is touched on the screen, the

screen returns to the previous screen even
when numbers have been entered.

Push <ENTER> while the current location map
screen or a scrolled map screen is displayed to
display the menu corresponding to that screen.

This menu can be used to access helpful
functions quickly, such as setting a destination
and searching for points of interest nearby.

To select a menu item, use the method
described earlier in this manual.

“Menu screen and how to operate”
(page 2-10)

INFO:

With the touch operation, the same screen can
be displayed by touching [Map Menu] located
on the map screen.

CURRENT LOCATION MAP SCREEN

If <ENTER> is pushed while the current
location map screen is displayed, the following
options are available.

. [Store Location]:

Store the current vehicle location in the
Address Book. The stored location can be
retrieved as necessary to set it as a
destination (waypoint).

“Storing location” (page 6-2)

. [Nearby Places]:

Search for points of interest near the current
vehicle location, such as restaurants and
gas stations, etc.

“Finding nearby place” (page 4-5)

. [Map View]:

Perform map operations such as the switch­ing of map type and the setting of map
orientation and scale.

“3. Map settings”

. [Map Icons]:

Select map icons of certain points of interest
(such as restaurants and gas stations, etc.)
to be displayed on the map around the
current vehicle location.

“Displaying map icons” (page 3-17)

. [Store Tracking]:

Store in the Address Book the route
travelled from the starting point to the
current location.

“Storing tracked route” (page 6-6)

Getting started 2-17

STORING HOME LOCATION/

ADDRESS

SCROLLED LOCATION MAP SCREEN

If <ENTER> is pushed while a scrolled map
screen is displayed, the following options are
available.

. [New Dest.]:

Set the destination to the map location
where <ENTER> was pushed. If a destina­tion is already set, the location will be set as
the new destination.

“Setting point on map” (page 4-19)

. [Add to Route]:

Set the map location where <ENTER> was
pushed as a destination or a waypoint.

This is available only when the suggested
route is already set.

“Setting destination or waypoint”
(page 5-14)

. [Nearby Places]:

Search for points of interest near the map
location where <ENTER> was pushed and

set them as a destination or waypoint.
Use the same search method as the one for

[Places].

“Finding nearby place” (page 4-5)

. [Store Location]:

Store in the Address Book the map location
where <ENTER> was pushed. The stored
location can be retrieved to set it as a
destination or waypoint.

“Storing location” (page 6-2)

. [Delete]:

Delete a stored location. To delete it, place
the cross pointer over the corresponding
icon.

. [Incident Detail]:

This function can be selected only when the
traffic information icon is displayed.

Display the details of the traffic information
icon.

Place the cross pointer over the icon you
want to check.

INFO:

Incident details are a feature of Traffic Informa­tion, and that a NavTraffic subscription is
required in order to receive Traffic Information.

2-18 Getting started

HOW TO STORE HOME LOCATION

If a home location is already stored in the
Address Book, it can be easily retrieved to set
the route to the stored home location.

The procedure to store the home location is the
same as for storing any other location.

“4. Setting destination”

As an example, the procedure for storing the
home location by searching for a destination by
address is described here.

1. Push <DEST>.

2. Highlight [Home (Add New)] and push
<ENTER>.

3. A confirmation message is displayed. Con­firm the contents of the message, highlight
[Yes] and push <ENTER>.

5. Enter the address of the home location,
highlight [OK] and push <ENTER>.

“Finding address” (page 4-4)

The map screen is displayed.

8. A message is displayed and the home
location is stored.

4. Highlight [Street Address] and push
<ENTER>. A character input screen is
displayed.

6. Adjust the location of your home using the
muti-function controller, if necessary.

7. After adjusting the location, push
<ENTER>.

9. Highlight [OK] and push <ENTER>.

10. Push <MAP> to return to the current
location map screen. The home icon is
displayed on the map.

INFO:

The same setting can also be performed by
pushing <SETTING> and highlighting [Naviga­tion].

“Storing location by searching” (page 6-2)

Getting started 2-19

SETTING DESTINATION

SEARCHING FOR DESTINATION

As an example, the method for setting a
restaurant as the destination using [Places] is
described here.

1. Push <DEST>.

2. Highlight [Places] and push <ENTER>.

3. Highlight [Nearby RESTAURANT] and push

<ENTER>.

INFO:

The search can also be narrowed down by
selecting [All Categories or Name] or
[ZAGAT] on this screen. By selecting [All
Categories or Name], the area, name of
facility, etc. can be specified. By selecting
[ZAGAT], restaurants registered in the ZA­GAT database can be searched and sorted
by its rating regarding food, decor, cost,
service, etc.

4. Highlight the preferred restaurant from the
list and push <ENTER>.

INFO:

. The position of the selected location is

displayed in the preview on the right side
of the screen.

. If there is a route already in progress, only

places along the current route will be
listed. Turn off [Show Along Route] at the

2-20 Getting started

top of list to display all nearby places.

5. The entire route is shown on the map.
Highlight [Start] after confirming the location
of the displayed destination, and push
<ENTER>.

The system sets the destination to the
selected location and starts calculating a
route.

INFO:

Even after setting a destination, the location
of the destination can be adjusted, the route
can be stored, etc. if necessary.

“Procedures after setting destination”
(page 5-2)