NAD C-315-BEE Service manual
NAD
SERVICE MANUAL
C 315BEE
STEREO
C 315BEE
STEREO
AMPLIFIER
AMPLIFIER
TABLE OF CONTENTS
DESCRIPTION P A G E
SERVICE CAUTION…………………………………………………………......3-4
REAR PANEL/FRONT PANEL VIEW………………………………………...5
SPECIFICATIONS…………………………………………………………....6
WIRING DIAGRAM………………………………………………………………7
BLOCK DIAGRAM……………………………………………………. …….......8-12
ALIGNMENT PROCEDURE…………………………………………….....13
SCHEMATICS………………………………………………………………..........14-16
PCB LAYOUT………………………………………………………………..........17-19
TROUBLE SHOOTING GUIDE…………………..........................................20
ELECTRICAL PARTS LIST……………………………………………..........21-27
EXPLODED VIEW…………………………………………………………….....28
EXPLODED VIEW PARTS LIST…………………………………………….......29
PACKING VIEW PARTS LIST………...…………………………………….......30
PRODUCT SAFETY SERVICING GUIDELINES
CAUTION : DO NOT ATTEMPT TO MODIFY THIS PRODUCT IN
ANY WAY. NEVER PERFORM CUSTOMIZED INSTALLATIONS
WITHOUT MANUFACTURER’S APPROVAL. UNAUTHORIZED
MODIFICATIONS WILL NOT ONLY VOID THE WARRANTY, BUT
MAY LEAD TO YOUR BEING LIABLE FOR ANY RESULTING
PROPERTY DAMAGE OR USER INJURY.
SERVICE WORK SHOULD BE PERFORMED ONLY AFTER YOU
ARE THOROUGHLY FAMILIAR WITH ALL OF THE FOLLOWING
SAFETY CHECKS AND SERVICING GUIDELINES. TO DO
OTHERWISE, INCREASES THE RISK OF POTENTIAL HAZARDS
AND INJURY TO THE USER.
WHILE SERVICING, USE AN ISOLATION TRANSFORMER FOR
PROTECTION FROM AC LINE SHOCK.
SAFETY CHECKS
AFTER THE ORIGINAL SERVICE PROBLEM HAS BEEN
CORRECTED. A CHECK SHOULD BE MADE OF THE
FOLLOWING.
SUBJECT : FIRE & SHOCK HAZARD
1. BE SURE THAT ALL COMPONENTS ARE POSITIONED IN
SUCH A WAY AS TO AVOID POSSIBILITY OF ADJACENT
COMPONENT SHORTS. THIS IS ESPECIALLY IMPORTANT
ON THOSE MODULES WHICH ARE TRANSPORTED TO AND
FROM THE REPAIR SHOP.
2. NEVER RELEASE A REPAIR UNLESS ALL PROTECTIVE
DEVICES SUCH AS INSULATORS, BARRIERS, COVERS,
SHIELDS, STRAIN RELIEFS, POWER SUPPLY CORDS, AND
OTHER HARDWARE HAVE BEEN REINSTALLED PER
ORIGINAL DESIGN. BE SURE THAT THE SAFETY PURPOSE
OF THE POLARIZED LINE PLUG HAS NOT BEEN DEFEATED.
3. SOLDERING MUST BE INSPECTED TO DISCOVER POSSIBLE
COLD SOLDER JOINTS, SOLDER SPLASHES OR SHARP
SOLDER POINTS. BE CERTAIN TO REMOVE ALL LOOSE
FOREIGN PARTICLES.
4. CHECK FOR PHYSICAL EVIDENCE OF DAMAGE OR
DETERIORATION TO PARTS AND COMPONENTS. FOR
FRAYED LEADS, DAMAGED INSULATION (INCLUDING AC
CORD). AND REPLACE IF NECESSARY FOLLOW ORIGINAL
LAYOUT, LEAD LENGTH AND DRESS.
5. NO LEAD OR COMPONENT SHOULD TOUCH A RECEIVING
TUBE OR A RESISTOR RATED AT 1 WATT OR MORE. LEAD
TENSION AROUND PROTRUDING METAL SURFACES MUST
BE AVOIDED.
6. ALL CRITICAL COMPONENTS SUCH AS FUSES,
FLAMEPROOF RESISTORS, CAPACITORS, ETC. MUST BE
REPLACED WITH EXACT FACTORY TYPES, DO NOT USE
REPLACEMENT COMPONENTS OTHER THAN THOSE
SPECIFIED OR MAKE UNRECOMMENDED CIRCUIT
MODIFICATIONS.
7. AFTER RE-ASSEMBLY OF THE SET ALWAYS PERFORM AN
AC LEAKAGE TEST ON ALL EXPOSED METALLIC PARTS OF
THE CABINET, (THE CHANNEL SELECTOR KNOB, ANTENNA
TERMINALS. HANDLE AND SCREWS) TO BE SURE THE SET
IS SAFET TO OPERATE WITHOUT DANGER OF ELECTRICAL
SHOCK. DO NOT USE A LINE ISOLATION TRANSFORMER
DURING THIS TEST USE AN AC VOLTMETER, HAVING 5000
OHMS PER VOLT OR MORE SENSITIVITY, IN THE
FOLLOWING MANNER; CONNECT A 1500 OHM 10 WATT
RESISTOR, PARALLELED BY A .15 MFD, 150V AC TYPE
CAPACITOR BETWEEN A KNOWN GOOD EARTH GROUND
(WATER PIPE, CONDUIT, ETC.) AND THE EXPOSED
METALLIC PARTS, ONE AT A TIME.
MEASURE THE AC VOLTAGE ACROSS THE COMBINATION
OF 1500 OHM RESISTOR AND .15 MFD CAPACITOR.
REVERSE THE AC PLUG AND REPEAT AC VOLTAGE
MEASUREMENTS FOR EACH EXPOSED METALLIC PART.
VOLTAGE MEASURE MUST NOT EXCEED 75 VOLTS R.M.S.
THIS CORRESPONDS TO 0.5 MILLIAMP AC ANY VALUE
EXCEEDING THIS LIMIT CONSTITUTES A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED IMMEDIATELY.
SUBJECT : GRAPHIC SYMBOLS
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN
EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF UNINSULATED “DANGEROUS VOLTAGE” WITHIN THE
PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
SUBJECT : TIPS ON PROPER INSTALLATION
1. NEVER INSTALL ANY PRODUCT IN A CLOSED-IN RECESS,
CUBBYHOLE OR CLOSELY FITTING SHELF SPACE. OVER
OR CLOSE TO HEAT DUCT, OR IN THE PATH OF HEATED
AIR FLOW.
2. AVOID CONDITIONS OF HIGH HUMIDITY SUCH AS:
OUTDOOR PATIO INSTALLATIONS WHERE DEW IS A
FACTOR, NEAR STEAM RADIATORS WHERE STEAM
LEAKAGE IS A FACTOR, ETC.
3. AVOID PLACEMENT WHERE DRAPERIES MAY OBSTRUCT
REAR VENTING. THE CUSTOMER SHOULD ALSO AVOID THE
USE OF DECORATIVE SCARVES OR OTHER COVERINGS
WHICH MIGHT OBSTRUCT VENTILATION.
4. WALL AND SHELF MOUNTED INSTALLATIONS USING A
COMMERCAL MOUNTING KIT MUST FOLLOW THE FACTORY
APPROVED MOUNTING INSTRUCTIONS A PRODUCT
MOUNTED TO A SHELF OR PLATFORM MUST RETAIN ITS
ORIGINAL FEET (OR THE EQUIVALENT THICKNESS IN
SPACERS) TO PROVIDE ADEQUATE AIR FLOW ACROSS
THE BOTTOM, BOLTS OR SCREWS USED FOR FASTENERS
MUST NOT TOUCH ANY PARTS OR WIRING. PERFORM
LEAKAGE TEST ON CUSTOMIZED INSTALLATIONS.
5. CAUTION CUSTOMERS AGAINST THE MOUNTING OF A
PRODUCT ON SLOPING SHELF OR A TILTED POSITION,
UNLESS THE PRODUCT IS PROPERLY SECURED.
6. A PRODUCT ON A ROLL-ABOUT CART SHOULD BE STABLE
ON ITS MOUNTING TO THE CART. CAUTION THE
CUSTOMER ON THE HAZARDS OF TRYING TO ROLL A CART
WITH SMALL CASTERS ACROSS THRESHOLDS OR DEEP
PILE CARPETS.
7. CAUTION CUSTOMERS AGAINST THE USE OF A CART OR
STAND WHICH HAS NOT BEEN LISTED BY UNDERWRITERS
LABORATORIES, INC. FOR USE WITH THEIR SPECIFIC
MODEL OF TELEVISION RECEIVER OR GENERICALLY
APPROVED FOR USE WITH T.V.’S OF THE SAME OR
LARGER SCREEN SIZE.
8. CAUTION CUSTOMERS AGAINST THE USE OF EXTENSION
CORDS, EXPLAIN THAT A FOREST OF EXTENSIONS
SPROUTING FROM A SINGLE OUTLET CAN LEAD TO
DISASTROUS CONSEQUENCES TO HOME AND FAMILY.
SERVICING PRECAUTIONS
CAUTION : Before servicing the A/V Receiver covered by this
service data and its supplements and addends, read and follow the
SAFETY PRECAUTIONS. NOTE : if unforeseen circumstances
create conflict between the following servicing precautions and any
of the safety precautions in this publication, always follow the safety
precautions.
Remember Safety First:
General Servicing Precautions
1. Always unplug the A/V Receiver AC power cord from the AC
power source before:
(1) Removing or reinstalling any component, circuit board,
module, or any other assembly.
(2) Disconnecting or reconnecting any internal electrical plug or
other electrical connection.
(3) Connecting a test substitute in parallel with an electrolytic
capacitor.
Caution : A wrong part substitution or incorrect polarity installation
of electrolytic capacitors may result in an explosion hazard.
2. Do not spray chemicals on or near this A/V Receiver or any of its
assemblies.
3. Unless specified otherwise in this service data, clean electrical
contacts by applying an appropriate contact cleaning solution to
the contacts with a pipe cleaner, cottontipped swab, or
comparable soft applicator.
Unless specified otherwise in this service data, lubrication of
contacts is not required.
4. Do not defeat any plug/socket B+ voltage interlocks with which
instruments covered by this service manual might be equipped.
5. Do not apply AC power to this A/V Receiver and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.
6. Always connect test instrument ground lead to the appropriate
ground before connecting the test instrument positive lead. Always
remove the test instrument ground lead last.
Insulation Checking Procedure
Disconnect the attachment plug from the AC outlet and turn the
power on. Connect an insulation resistance meter(500V) to the
blades of the attachment plug. The insulation resistance between
each blade of the attachment plug and accessible conductive parts
(Note 1) should be more than 1M-ohm.
Note 1 : Accessible Conductive Parts including Metal panels, Input
terminals, Earphone jacks, etc.
Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by
static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical Es
devices are integrated circuits and some field effect transistors and
semiconductor chip components.
The following techniques should be used to help reduce the
incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor component or
semiconductor-equipped assembly, drain off any electrostatic
charge on your body by touching a known earth ground.
Alternatively, obtain and wear a commercially available
discharging wrist strap device, which should be removed for
potential shock reasons prior to applying power to the unit under
test.
2. After removing an electrical assembly equipped with ES devices,
place the assembly on a conductive surface such as aluminum
foil, to prevent electrostatic charge buildup or exposure of the
assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES
devices.
4. Use only an antistatic solder removal device. Some solder
removal devices not classified a “anti-static” can generate
electrical charges sufficient to damage ES devices.
5. Do not use freonpropelled chemicals. These can generate
electrical charge sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective
package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically
shorted together by conductive foam, aluminum foil, or
comparable conductive material).
7. lmmediately before removing the protective material from the
leads of a replacement ES device, touch the protective material to
the chassis or circuit assembly into which the device will be
installed.
Caution : Be sure no power is applied to the chassis or circuit, and
observe all other safety precautions.
8. Minimize bodily motions when handing unpackaged replacement
ES devices. (Normally harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a
carpeted floor can generate static electricity sufficient to damage
an ES device.)
'30/51"/&-$0/530-4'*(63&
1
2
7
Stereo Integrated Amplifier C 315BEE
PHONES
TAPE VIDEOTUNER CD
TONE
DEFEAT
TREBLE
BALANCE
AUX
DISC
MP
BASS
VOLUME
"±/"3'
N©DAC EEB513
3
1. POWER
2. POWER/STAND BY/
PROTECTION LED
3. HEADPHONE
4. INPUT SELECTOR
4
5
6
89
5. IR RECEIVER
6. TONE CONTROLS
7. TONE DEFEAT
8. BALANCE CONTROL
9. VOLUME CONTROL
3&"31"/&-$0//&$5*0/4'*(63&
1. DISC INPUT
2. CD INPUT
3. VIDEO INPUT
4. AUX INPUT
5. TUNER INPUT
6. TAPE IN/OUT
7. SPEAKERS OUT
8. AC LINE CORD
9. POWER SWITCH
SPECIFICATIONS
PREAMP IN , SPEAKERS OUT
CONTINUOUS AVERAGE POWER 40 W (16 dBW)
OUTPUT INTO 8 OHMS OR 4 OHMS
(Min. power per channel, 20 Hz – 20 kHz,
with no more than rated distortion)
THD + Noise < 0.02%
Clipping power 45 W
(maximum continuous power per channel 4 and 8).
IHF dynamic headroom: at 8 ohms + 3.6 dB
at 4 ohms + 4.8 dB
IHF dynamic power
(maximum short term power per channel) 8 ohms: 90W (19.5 dBW)
4 ohms: 120W (20.8 dBW)
2 ohms: 170 W (22.3 dBW)
Damping factor(ref. 8 ohms 1 kHz) > 200
Input Impedance R = 50 kohms
C = 100pF
Input sensitivity (for rated output into 8 ohms) 200 mV
Voltage gain 39 dB
Frequency response 20 Hz – 20 kHz <+/-1.0 dB (tone defeat off)
<+/-0.2dB (tone defeat on)
Signal / Noise ratio, A-weighted 95dB ref. 1 W
111dB ref. 40 W
SMPTE I.M. < 0.02%
(Intermodulation Distortion, 60 Hz + 7 kHz,
4:1, from 250 mW to rated output)
IHF I.M. < 0.01%
(CCIF IM Distortion, 19 + 20 kHz at rated output)
Headphones Output Impedance 68 ohms
Maximum input signal 7 V
CONTROLS
Treble +/- 5 dB at 10 kHz
Bass +/- 8 dB at 100 Hz
DIMENSIONS AND WEIGHTS Net Weight 5.25 kg ( 11.5 Ib)
Shipping Weight 6.5 kg (14.3lb)
DIMENSION (WHD) 435 X70 X 242mm
BLOCK DIAGRAM
TAPE OUT R
TAPE OUT L
TAPE1 IN R
TAPE1 IN L
TUNER R
TUNER L
AUX R
VIDEO R
AUX L
VIDEO L
CD R
CD L
DISC R
DISC L
MP R
MP L
JK31
FOR RECORD OUT
Speaker L
HEADPHONE
Speaker R
RL301
JQX-115F/24
(80 DEGREE C)
POSISTOR
R330
MUTE CIRCUIT
CIRCUIT
THE MAIN HEATSINK)
MUTE
Q120
MUTE
Q220
PROTECTION
CIRCUIT(Q122,Q222 ON
TEMP COMPENSATION
INPUT SELECTION IC(TC9164CNG)
PREAPM AMP CIRCUIT
+/-17V SUPPLY CIRCUIT
SW31
RT34
RT32
RT31
TONE DEFEAT
BASS
BALANCE
TREBLE
INPUT AND STANDBY
INDICATION LEDS
MCU(W78E52C)
POWER AMP
CIRCUIT R
MAIN IN L
POWER AMP
CIRCUIT L
MAIN IN R
MUTE
MUTE
Q105
Q205
MAIN MUTE
CIRCUIT
+/-45V SUPPLY CIRCUIT
PRE-OUT R
PRE-OUT L
VOL-
CIRCUIT (REMOTE)
CONTROL
VOL+
VOLUME CONTROL
VOLUME
RT33
IC503
IR receiver
3
2
1
Volume
Circuit
Main Mute
Circuit
Record Out
Mute Circuit
+5V
V
S
G
IC502
24C01
Vss4SDA
NC
NC
NC
SCL
NC
Vcc
MICROPROCESSOR CONNECTION DIAGRAM
D501
U301
TC9164
Input Selection IC
DATA
CLK
STB
IC501
AT89S51
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
5
6
7
8
+5V
16
17
18
19
20
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
RST
RXD/P3.0
TXD/P3.1
INT0/P3.2
INT1/P3.3
T0/P3.4
T1/P3.5
WR/P3.6
RD/P3.7
XTAL2
XTAL1
VSS
VDD
P0.0/AD0
P0.1/AD1
P0.2/AD2
P0.3/AD3
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
EA
ALE
PSEN
P2.7/A15
P2.6/A14
P2.5/A13
P2.4/A12
P2.3/A11
P2.2/A10
P2.1/A9
P2.0/A8
+5V
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
Standby LED
BLUE
AMBER
RED
Input selection
Keys and LEDS
C504
27P
X501
11.0592MHz
C505
27P
Sandby control line
18V Power Supply
Control Circuit
PHONE5
MP IN
24C01
KEY BOARD IC502
3,1&21),*85$7,21
)81&7,21$/%/2&.',$*5$0
9FF
6'$
6&/
:3
6/$9($''5(66
5(*,67(5
&203$5$725
1
NC
2
NC
3
NC
4 5
VSS
&21752/
/2*,&
8
VCC
7
NC
6
SCL
SDA
+,*+92/7$*(
*(1(5$725
7,0,1*&21752/
;
'(&2'(5
((3520
$55$<
*1'
:25'$''5(66
&2817(5
<
'(&2'(5
$&.
Q026
&ORFN
',2
!
5(*,67(5
'$7$
Loading...