Mitsubishi PLH-P1.6KAH, PLH-P2KAH, PLH-P2.5KAH, PLH-P3KAH, PLH-P4KAH SERVICE MANUAL

1999

SPLIT-TYPE,HEAT PUMP AIR CONDITIONERS SPLIT-TYPE,AIR CONDITIONERS

No. OC181

REVISED EDITION-A

TECHNICAL & SERVICE MANUAL

	Series PLH/PLA	Ceiling Cassettes	R407C		control relation.
					Refer to the OCT03 as regarding
					Revised Edition-A are
	Indoor unit				PLA-P1.6KA, P2KA, P2.5KA,
		[Service Ref.]			P3KA, P4KA, P5KA, P6KA, and
	[Model names]
					PUH-P1.6, P2, P2.5YGA added.
	1999	1999			This manual does not cover the
	PLH-P1.6KAH	PLH-P1.6KAH			following outdoor units. When
	PLH-P2KAH	PLH-P2KAH			servicing them, please refer to
					the service manual No.OC180
	PLH-P2.5KAH	PLH-P2.5KAH
					REVISED EDITION-A and this
	PLH-P3KAH	PLH-P3KAH			manual in a set.
	PLH-P4KAH	PLH-P4KAH			[Service Ref.]
	PLH-P5KAH	PLH-P5KAH			PUH-P1.6VGA PU-P1.6VGA
	PLH-P6KAH	PLH-P6KAH			PUH-P1.6YGA
					PUH-P2VGA	PU-P2VGA
	2000	2000
					PUH-P2YGA
	PLA-P1.6KA	PLA-P1.6KA
					PUH-P2.5VGA PU-P2.5VGA
	PLA-P2KA	PLA-P2KA			PUH-P2.5YGA
	PLA-P2.5KA	PLA-P2.5KA			PUH-P3VGA PU-P3VGA
	PLA-P3KA	PLA-P3KA			PUH-P3YGA PU-P3YGA
	PLA-P4KA	PLA-P4KA			PUH-P4YGA	PU-P4YGA
					PUH-P5YGA	PU-P5YGA
	PLA-P5KA	PLA-P5KA
					PUH-P6YGA	PU-P6YGA
	PLA-P6KA	PLA-P6KA

INDOOR UNIT

FILTER

CHECK MODE

TEST RUN

CONTENTS

1.COMBINATION OF INDOORAND OUTDOOR UNITS··2

2.SAFETY PRECAUTION·······························3

3.PART NAMES AND FUNCTIONS ···············5

4.SPECIFICATIONS ········································8

5.DATA ··························································19

6.OUTLINES AND DIMENSIONS ·················45

7.WIRING DIAGRAM ·······································48

8.REFRIGERANT SYSTEM DIAGRAM··············51

9.DISASSEMBLY PROCEDURE ··················53

10.PARTS LIST ···············································56

11.OPTIONAL PARTS·····································68

REMOTE CONTROLLER

1 COMBINATION OF INDOOR AND OUTDOOR UNITS

Outdoor unit

Indoor unit

Heat pump type

Cooling only type

PUH-P · VGA / YGA

PU-P · VGA / YGA

1.6VGA

1.6YGA

2VGA

2YGA

2.5VGA

2.5YGA

3VGA

3YGA

4YGA

5YGA

6YGA

1.6VGA

2VGA

2.5VGA

3VGA

3YGA

4YGA

5YGA

6YGA

Heat pump with

PLH-P1.6KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLH-P2KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

electric heater

PLH-P2.5KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLH-P3KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLH-P4KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLH-P5KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLH-P6KAH

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

Heat pump without

PLA-P1.6KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLA-P2KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

electric heater

or

PLA-P2.5KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

Cooling only

PLA-P3KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLA-P4KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLA-P5KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

PLA-P6KA

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

—

2

2 SAFETY PRECAUTION

Cautions for using with the outdoor unit which adopts R407C refrigerant.

·Do not use the existing refrigerant piping.

-The old refrigerant and refrigerant oil in the existing piping contains a large amount of chlorine which may cause the refrigerant oil of the new unit to deteriorate.

·Do not use copper pipes which are broken, deformed or discolour .

In addition, be sure that the inner surfaces of the pipes are clean, free of hazardous sulphur and oxides, or have no dust / dirt, shaving particles, oils, moisture or any other contamination.

-If there is a large amount of residual oil (hydraulic oil, etc.) inside the piping and joints, deterioration of the refrigerant oil will result.

·Store the piping to be used during installation indoors and keep both ends of the piping sealed until just before brazing. (Store elbows and other joints in a plastic bag.)

-If dust, dirt, or water enters the refrigerant cycle, deterioration of the oil and compressor trouble may result.

·Use ester oil, ether oil or alkyl benzene (small amount) as the refrigerant oil to coat flares and flange connections.

-The refrigerant oil will degrade if it is mixed with a large amount of mineral oil.

Use liquid refrigerant to fill the system.

-If gas refrigerant is used to fill the system, the composition of the refrigerant in the cylinder will change and performance may drop.

·Do not use a refrigerant other than R407C.

-If another refrigerant (R22, etc.) is used, the chlorine in the refrigerant may cause the refrigerant oil to deteriorate.

·Use a vacuum pump with a reverse flow check valve.

-The vacuum pump oil may flow back into the refrigerant cycle and cause the refrigerant oil to deteriorate.

·Do not use the following tools that are used with conventional refrigerant.

(Gauge manifold , charge hose, gas leak detector, reverse flow check valve, refrigerant charge base, vacuum gauge, refrigerant recovery equipment)

-If the conventional refrigerant and refrigerant oil are mixed in the R407C, the refrigerant may deteriorated. -If water is mixed in the R407C, the refrigerant oil may deteriorate.

-Since R407C does not contain any chlorine, gas leak detectors for conventional refrigerant will not react to it.

·Do not use a charging cylinder.

-Using a charging cylinder may cause the refrigerant to deteriorate.

·Be especially careful when managing the tools.

-if dust, dirt, or water gets in the refrigerant cycle, the refrigerant may deteriorate.

·Do not use the drier which is sold in the field.

-The drier for R407C refrigerant is per-attached to outdoor unit refrigerant circuit. -Some drier in the field are not in conformity with R407C refrigerant .

3

[1] Service tools

Use the below service tools as exclusive tools for R407C refrigerant.

No.	Tool name	Specifications
1	Gauge manifold	·Only for R407C.
		·Use the existing fitting SPECIFICATIONS. (UNF7/16)
		·Use high-tension side pressure of 3.43MPa·G or over.
2	Charge hose	·Only for R407C.

·Use pressure performance of 5.10MPa·G or over.

3Electronic scale

4	Gas leak detector	·Use the detector for R407C.
5	Adapter for reverse flow check.	·Attach on vacuum pump.

6Refrigerant charge base.

7 Refrigerant cylinder.

·For R407C

·Top of cylinder (Brown)

·Cylinder with syphon

8Refrigerant recovery equipment.

[2]Notice on repair service

·After recovering the all refrigerant in the unit, proceed to working. ·Do not release refrigerant in the air.

·After completing the repair service, recharge the cycle with the specified amount of liquid refrigerant.

[3] Refrigerant recharging

(1) Refrigerant recharging process

1Direct charging from the cylinder.

·R407C cylinder are available on the market has a syphon pipe. ·Leave the syphon pipe cylinder standing and recharge it.

(By liquid refrigerant)

Unit

Gravimeter

(2) Recharge in refrigerant leakage case

·After recovering the all refrigerant in the unit, proceed to working. ·Do not release the refrigerant in the air.

·After completing the repair service, recharge the cycle with the specified amount of liquid refrigerant.

4

3 PART NAMES AND FUNCTIONS

● Indoor (Main) Unit
PLH-P1.6KAH,	PLA-P1.6KA
PLH-P2KAH,	PLA-P2KA
PLH-P2.5KAH,	PLA-P2.5KA
PLH-P3KAH,	PLA-P3KA
PLH-P4KAH,	PLA-P4KA
PLH-P5KAH,	PLA-P5KA
PLH-P6KAH,	PLA-P6KA
		Filters	dust and pollutants
		Remove
		from inhaled air

Horizontal Air Outlet

Sets airflow horizontal automatically during cooling or dehumidifying.

Grille

Auto Air Swing Vane Disperses airflow up and down and adjusts the angle of airflow direction.

Air Intake

Inhales air from room.

5

● Remote controller

● Once the controls are set, the same operation mode can be repeated by simply pressing the ON/OFF button.

● Operation buttons

		TIME SETTING button
TIMER button		This sets of switches the		AIR SPEED button
This switches between		current time. start time and		This sets the fan speed.
		stop time.
continuous operation and
the timer operation.

OPERATION SWITCH			ON/OFF button
button			This switches between the
Press this button to			operation and stop modes
switch the cooler			each time it is pressed. The
electronic dry			lamp on this button lights
(dehumidify) automatic			during operation.
and heater modes.			AIR DIRECTION button
			This adjusts the vertical angle
TEMP. ADJUSTMENT			of the ventilation.
			FILTER button
button
This sets the room			This resets the filter cleaning
			indication display.
temperature The temperature
setting can be performed in
1°C units			CHECK-TEST RUN button
Setting range
Cooler	19°C to 30°C		Only press this button to
Heater	17°C to 28°C		perform an inspection check
			or test operation Do not use
TIMER ADJUSTMENT button		LOUVER button	it for normal operation.
This adjust the current time, start		This switches the	VENTILATION button
time and stop time.		horizontal fan motion	This sets the ventilation fan
		ON and OFF.
			speed.
		(This button does not
		operate in this model)

6

● Display

CENTRALLY CONTROLLED display

This indicates when the unit is controlled by optional features such as central control type remote controller.

TIMER display

This indicates when the continuous operation and time operation modes are set.

It also display the time for the timer operation at the same time as when it is set.

OPERATION MODE display

This indicates the operation mode.

STANDBY display

This indicates when the standby mode is set from the time the sleep operation starts until the heating air is discharged.

DEFROST display

This indicates when the defrost operation is performed.

CLOCK display

The current time , start time and stop time can be displayed in ten second intervals by pressing the time switch button. The start time or stop time is always displayed during the timer operation.

In this display example on the bottom left, a condition where all display lamps light is shown for explanation purposes although this differs from actual operation.

AIR DIRECTION display

The selected fan speed is displayed.

FAN SPEED display

This displays the air direction.

ROOM TEMPERATURE display

The temperature of the suction air is displayed during operation. The display range is 8° to 39°C. The display flashes 8°C when the actual temperature is less than 8° and flashes 39°C when the actual temperature is greater than 39°C.

Operation lamp

This lamp lights during operation, goes off when the unit stops and flashes when a malfunction occurs.

CHECK MODE

display

TEST RUN

This display lights in the check mode or when a test operation is performed.

CHECK display
This indicates when a malfunction		SET TEMPERATURE display		POWER display
has occurred in the unit which should		This displays the selected setting		This lamp lights when electricity is
be checked.
		temperature.		supplied to the unit.

Caution

FILTER display

This lamp lights when the filter need to be cleaned.

●Only the Power display lights when the unit is stopped and power supplied to the unit.

●When power is turned ON for the first time the (CENTRAL CTRL) display appears to go off momentarily but this is not a malfunction.

●When the central control remote control unit, which is sold separately, is used the ON-OFF button, operation switch button and TEMP. adjustment button do not operate.

●“NOT AVAILABLE” is displayed when the Air speed button are pressed.This indicates that this room unit is not equipped with the fan direction adjustment function and the louver function.

●When power is turned ON for the first time, it is normal that “H0” is displayed on the room temperature indication (For max. 2minutes). Please wait until this “H0” indication disappear then start the operation.

7

4 SPECIFICATIONS

1.Heat pump

Service Ref.	With Electric heater	PLH-P1.6KAH
Item	Without Electric heater	PLA-P1.6KA

Function									Cooling		Heating
Capacity		w1					Btu/h		15,000		17,100(21,800)
							W		4,400		5,000(6,400)
Total input		w1					kW		1.86		1.93(3.33)
	Service Ref.				With Electric heater				PLH-P1.6KAH
					Without Electric heater				PLA-P1.6KA
	Power supply(phase, cycle,voltage)								Single, 50Hz, 220-240V
		Input		w2			kW		0.15		0.10<1.40>
		Running current		w2			A		0.64		0.45<5.83>
		Starting current		w2			A		0.70		0.50<5.83>
	External finish								Galvanized sheets with gray heat insulation
UNIT	Heat exchanger									Plate fin coil
	Fan	Fan(drive) x No.							Turbo fan (direct) x 1
INDOOR		Fan motor output					kW			0.030
		Airflow(Lo-Mi1-Mi2-Hi)					m3/min(CFM)		13-14-15-16(459-494-530-565)
		External static pressure					Pa(mmAq)		0(direct blow)
	Booster heater			w2			kW			<1.4>
	Operation control & Thermostat								Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)						dB		32-34-35.5-37
	Unit drain pipe I.D.						mm(in.)			32(1-1/4)
	Dimensions				W		mm(in.)		UNIT : 660(26) PANEL : 760(30)
					D		mm(in.)		UNIT : 660(26) PANEL : 760(30)
					H		mm(in.)		UNIT : 253(10) PANEL : 30(1-1/8)
	Weight	With Electric heater					kg(lbs)		UNIT : 20(44)		PANEL : 3.7(8)
		Without Electric heater					kg(lbs)		UNIT : 19(42)		PANEL : 3.7(8)
	Service Ref.								PUH-P1.6VGA / YGA
	Power supply (phase, cycle, voltage)							Single, 50Hz, 220-240V / 3-ph, 50Hz, 380-415V(4wires)
		Input					kW		1.71		1.83
		Running current					A		7.66 / 2.67		8.19 / 2.86
		Starting current					A			36 / 20
	External finish								Munsell 5Y 8/1
	Refrigerant control								Linear Expansion Valve
	Compressor									Hermetic
UNIT		Model							RE277VHSM / RE277YFKM
		Motor output					kW				1.3
OUTDOOR		Starter type								Line start
		Protection devices						Inner thermostat, HP switch,Discharge thermo. / Thermal rely, Discharge thermo, HP switch, Anti-phase protector.
	Heat exchanger									Plate fin coil
	Fan	Fan(drive) x No.							Propeller (direct) x 1
		Fan motor output					kW			0.070
		Airflow					m3/min(CFM)			45(1,590)
		Crankcase heater					W				30
	Defrost method								Reverse cycle
	Noise level			Cooling			dB				46
				Heating			dB				48
	Dimensions				W		mm(in.)		900(35-7/16)
					D		mm(in.)		330+20(13+3/4)
					H		mm(in.)		650 (25-5/8)
	Weight						kg(lbs)			55(121)
PIPING	Refrigerant									R407C
		Charge					kg(lbs)			2.6(5.7)
		Oil (Model)		Liquid			L		0.57 (Ester)MEL56
REFRIGERANT	Pipe size O.D.						mm(in.)			9.52 (3/8)
				Gas			mm(in.)			15.88 (5/8)
	Connection method			Indoor side						Flared
				Outdoor side						Flared
	Between the indoor &			Height difference						Max. 40m
	outdoor unit			Piping length						Max. 40m
Notes1. Rating Conditions (ISO T1)
	Cooling : Indoor		: D.B. 27˚C(80˚F),				W.B. 19˚C (66˚F) Outdoor		: D.B. 35˚C(95˚F),	W.B. 24˚C (75˚F)
	Heating :Indoor		: D.B. 20˚C(68˚F)					Outdoor	: D.B. 7˚C(45˚F),	W.B. 6˚C (43˚F)

Refrigerant piping length (one way) : 5m (16ft)

	2. Guaranteed operating range
				Indoor	Outdoor
		Cooling	Upper limit	D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
			Lower limit	D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
		Heating	Upper limit	D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
			Lower limit	D.B. 17˚C	D.B. -11˚C, W.B. -12˚C

w1 : ( ) Shows the total rating.

w2 : < > Shows the only booster heater rating.

3. Above data based on indicated voltage

Indoor Unit	1 phase 240V	50Hz
Outdoor Unit	1 phase 240V	50Hz / 3 phase 415V 50Hz

8

Item		Service Ref. With Electric heater			PLH-P2KAH
		Without Electric heater			PLA-P2KA
Function				Cooling	Heating
Capacity	w1		Btu/h	18,400	21,300(26,100)
			W	5,400	6,250(7,650)
Total input	w1		kW	2.62	2.67(4.07)

Service Ref.

With Electric heater

PLH-P2KAH

Without Electric heater

PLA-P2KA

Power supply(phase, cycle,voltage)

Single, 50Hz, 220-240V

Input

w2

kW

0.14

0.10<1.40>

Running current

w2

A

0.65

0.45<5.83>

Starting current

w2

A

0.72

0.50<5.83>

External finish

Galvanized sheets with gray heat insulation

UNIT

Heat exchanger

Plate fin coil

Fan

Fan(drive) x No.

Turbo fan (direct) x 1

Fan motor output

kW

0.030

INDOOR

Airflow(Lo-Mi1-Mi2-Hi)

m3/min(CFM)

13-14-15-16(459-494-530-565)

External static pressure

Pa(mmAq)

0(direct blow)

Booster heater

w2

kW

<1.4>

Operation control & Thermostat

Remote controller & built-in

Noise level(Lo-Mi1-Mi2-Hi)

dB

32-34-35.5-37

Unit drain pipe I.D.

mm(in.)

32(1-1/4)

Dimensions

W

mm(in.)

UNIT : 660(26) PANEL : 760(30)

D

mm(in.)

UNIT : 660(26) PANEL : 760(30)

H

mm(in.)

UNIT : 253(10) PANEL : 30(1-1/8)

Weight

With Electric heater

kg(lbs)

UNIT : 20(44)

PANEL : 3.7(8)

Without Electric heater

kg(lbs)

UNIT : 19(42)

PANEL : 3.7(8)

Service Ref.

PUH-P2VGA / YGA

Power supply (phase, cycle, voltage)

Single, 50Hz, 220-240V / 3-ph, 50Hz, 380-415V(4wires)

Input

kW

2.48

2.57

Running current

A

11.11 / 3.88

11.51 / 4.02

Starting current

A

74 / 30

External finish

Munsell 5Y 8/1

Refrigerant control

Linear Expansion Valve

Compressor

Hermetic

UNIT

Model

NE38VMJM / NE38YEJM

Motor output

kW

1.7

Starter type

Line start

OUTDOOR

Protection devices

Inner thermostat, HP switch, Discharge thermo. / Thermal rely, Discharge thermo, HP switch, Anti-phase protector.

Heat exchanger

Plate fin coil

Fan

Fan(drive) x No.

Propeller (direct) x 1

Fan motor output

kW

0.070

Airflow

m3/min(CFM)

55(1,940)

Crankcase heater

W

38

Defrost method

Reverse cycle

Noise level

Cooling

dB

48

Heating

dB

49

Dimensions

W

mm(in.)

900(35-7/16)

D

mm(in.)

330+20(13+3/4)

H

mm(in.)

855 (33-5/8)

Weight

kg(lbs)

71(157)

PIPING

Refrigerant

R407C

Charge

kg(lbs)

3.1(6.8)

Oil (Model)

Liquid

L

1.2 (Ester)MEL56

REFRIGERANT

Pipe size O.D.

mm(in.)

9.52 (3/8)

Gas

mm(in.)

15.88 (5/8)

Connection method

Indoor side

Flared

Outdoor side

Flared

Between the indoor &

Height difference

Max. 40m

outdoor unit

Piping length

Max. 40m

Notes1. Rating Conditions (ISO T1)

Cooling : Indoor

: D.B. 27˚C(80˚F),

W.B. 19˚C (66˚F) Outdoor

: D.B. 35˚C(95˚F),

W.B. 24˚C (75˚F)

Heating :Indoor

: D.B. 20˚C(68˚F)

Outdoor

: D.B. 7˚C(45˚F),

W.B. 6˚C (43˚F)

Refrigerant piping length (one way) : 5m (16ft)

2. Guaranteed operating range

w1 : ( ) Shows the total rating.

Indoor

Outdoor

w2 : < > Shows the only booster heater rating.

Cooling

Upper limit

D.B. 35˚C, W.B. 22.5˚C

D.B. 46˚C

Lower limit

D.B. 19˚C,

W.B. 15˚C

D.B. -5˚C

Heating

Upper limit

D.B. 28˚C

D.B. 24˚C, W.B. 18˚C

Lower limit

D.B. 17˚C

D.B. -11˚C, W.B. -12˚C

3. Above data based on indicated voltage

Indoor Unit

1 phase 240V 50Hz

Outdoor Unit

1 phase 240V 50Hz / 3 phase 415V 50Hz

9

Service Ref.	With Electric heater	PLH-P2.5KAH
Item	Without Electric heater	PLA-P2.5KA

Function									Cooling		Heating
Capacity		w1					Btu/h		21,500		25,200(32,400)
							W		6,300		7,400(9,500)
Total input		w1					kW		2.77		2.68(4.78)
	Service Ref.				With Electric heater				PLH-P2.5KAH
					Without Electric heater				PLA-P2.5KA
	Power supply(phase, cycle,voltage)								Single, 50Hz, 220-240V
		Input		w2			kW		0.14		0.10<2.10>
		Running current		w2			A		0.61		0.45<8.75>
		Starting current		w2			A		0.67		0.50<8.75>
	External finish								Galvanized sheets with gray heat insulation
UNIT	Heat exchanger									Plate fin coil
	Fan	Fan(drive) x No.							Turbo fan (direct) x 1
INDOOR		Fan motor output					kW			0.030
		Airflow(Lo-Mi1-Mi2-Hi)					m3/min(CFM)		14-15-16-17 (494-530-565-600)
		External static pressure					Pa(mmAq)		0(direct blow)
	Booster heater			w2			kW			<2.1>
	Operation control & Thermostat								Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)						dB		35-36.5-38-39.5
	Unit drain pipe I.D.						mm(in.)			32(1-1/4)
	Dimensions				W		mm(in.)		UNIT : 660(26) PANEL : 760(30)
					D		mm(in.)		UNIT : 660(26) PANEL : 760(30)
					H		mm(in.)		UNIT : 253(10) PANEL : 30(1-1/8)
	Weight	With Electric heater					kg(lbs)		UNIT : 21(46)		PANEL : 3.7(8)
		Without Electric heater					kg(lbs)		UNIT : 20(44)		PANEL : 3.7(8)
	Service Ref.								PUH-P2.5VGA / YGA
	Power supply (phase, cycle, voltage)							Single, 50Hz, 220-240V / 3-ph, 50Hz, 380-415V(4wires)
		Input					kW		2.63		2.58
		Running current					A		11.78 / 4.11		11.55 / 4.03
		Starting current					A			77 / 32
	External finish								Munsell 5Y 8/1
	Refrigerant control								Linear Expansion Valve
	Compressor									Hermetic
UNIT		Model							NE41VMJM / NE41YEJM
		Motor output					kW				1.9
OUTDOOR		Starter type								Line start
		Protection devices						Internal thermostat, HP switch, Discharge thermo. / Thermal rely, Discharge thermo, HP switch, Anti-phase protector.
	Heat exchanger									Plate fin coil
	Fan	Fan(drive) x No.							Propeller (direct) x 1
		Fan motor output					kW			0.070
		Airflow					m3/min(CFM)			50(1,770)
		Crankcase heater					W				38
	Defrost method								Reverse cycle
	Noise level			Cooling			dB				48
				Heating			dB				50
	Dimensions				W		mm(in.)		900(35-7/16)
					D		mm(in.)		330+20(13+3/4)
					H		mm(in.)		855 (33-5/8)
	Weight						kg(lbs)			82(181)
PIPING	Refrigerant									R407C
		Charge					kg(lbs)			3.3(7.3)
		Oil (Model)		Liquid			L		1.2 (Ester)MEL56
REFRIGERANT	Pipe size O.D.						mm(in.)			9.52 (3/8)
				Gas			mm(in.)			15.88 (5/8)
	Connection method			Indoor side						Flared
				Outdoor side						Flared
	Between the indoor &			Height difference						Max. 50m
	outdoor unit			Piping length						Max. 50m
Notes1. Rating Conditions (ISO T1)
	Cooling : Indoor		: D.B. 27˚C(80˚F),				W.B. 19˚C (66˚F) Outdoor		: D.B. 35˚C(95˚F),	W.B. 24˚C (75˚F)
	Heating :Indoor		: D.B. 20˚C(68˚F)					Outdoor	: D.B. 7˚C(45˚F),	W.B. 6˚C (43˚F)

Refrigerant piping length (one way) : 5m (16ft)

	2. Guaranteed operating range
				Indoor	Outdoor
		Cooling	Upper limit	D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
			Lower limit	D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
		Heating	Upper limit	D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
			Lower limit	D.B. 17˚C	D.B. -11˚C, W.B. -12˚C

w1 : ( ) Shows the total rating.

w2 : < > Shows the only booster heater rating.

3. Above data based on indicated voltage

Indoor Unit	1 phase 240V	50Hz
Outdoor Unit	1 phase 240V	50Hz / 3 phase 415V 50Hz

10

Service Ref.	With Electric heater	PLH-P3KAH
Item	Without Electric heater	PLA-P3KA

	Function						Cooling	Heating
	Capacity		w1			Btu/h	26,300	31,400(38,500)
						W	7,700	9,200(11,300)
	Total input		w1			kW	3.47	3.65(5.75)
		Service Ref.			With Electric heater		PLH-P3KAH
					Without Electric heater		PLA-P3KA
		Power supply(phase, cycle,voltage)					Single, 50Hz, 220-240V
			Input	w2		kW	0.13	0.13<2.10>
			Running current	w2		A	0.62	0.62<8.75>
			Starting current	w2		A	0.91	0.91<8.75>
		External finish					Galvanized sheets with gray heat insulation
	UNIT	Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Turbo fan (direct) x 1
			Fan motor output			kW	0.070
	INDOOR
			Airflow(Lo-Mi1-Mi2-Hi)			m3/min(CFM)	15-16.5-18.5-20 (530-582-653-706)
			External static pressure			Pa(mmAq)	0(direct blow)
		Booster heater		w2		kW	<2.1>
		Operation control & Thermostat					Remote controller & built-in
		Noise level(Lo-Mi1-Mi2-Hi)				dB	32-34-37-39
		Unit drain pipe I.D.				mm(in.)	32(1-1/4)
		Dimensions			W	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					D	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					H	mm(in.)	UNIT : 290(11)	PANEL : 30(1-1/8)
		Weight	With Electric heater			kg(lbs)	UNIT : 28(62)	PANEL : 5(11)
			Without Electric heater			kg(lbs)	UNIT : 26(57) PANEL : 5(11)
		Service Ref.					PUH-P3VGA / YGA
		Power supply (phase, cycle, voltage)					Single, 50Hz, 220-240V / 3-ph, 50Hz, 380-415V (4wires)
			Input			kW	3.34	3.52
			Running current			A	14.64/5.46	15.43/5.76
			Starting current			A	93/41
		External finish					Munsell 5Y 8/1
		Refrigerant control					Linear Expansion Valve
		Compressor					Hermetic
	UNIT		Model				NE52VNJM / NE52YDJM
			Motor output			kW	2.5
			Starter type				Line start
	OUTDOOR
			Protection devices				Internal thermostat, HP switch, Discharge thermo. / Thermal rely, Discharge thermo, HP switch, Anti-phase protector.
		Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Propeller (direct) x 1
			Fan motor output			kW	0.070
			Airflow			m3/min(CFM)	50(1,770)
			Crankcase heater			W	38
		Defrost method					Reverse cycle
		Noise level		Cooling		dB	49
				Heating		dB	51
		Dimensions			W	mm(in.)	900(35-7/16)
					D	mm(in.)	330+20(13+3/4)
					H	mm(in.)	855 (33-5/8)
		Weight				kg(lbs)	82(181)
	PIPING	Refrigerant					R407C
			Charge			kg(lbs)	3.7(8.2)
			Oil (Model)	Liquid		L	1.6 (Ester)MEL56
	REFRIGERANT	Pipe size O.D.				mm(in.)	9.52 (3/8)
				Gas		mm(in.)	15.88 (5/8)
		Connection method		Indoor side			Flared
				Outdoor side			Flared
		Between the indoor &		Height difference			Max. 50m
		outdoor unit		Piping length			Max. 50m

Notes1. Rating Conditions (ISO T1)
Cooling : Indoor			: D.B. 27˚C(80˚F), W.B. 19˚C (66˚F) Outdoor			: D.B. 35˚C(95˚F),		W.B. 24˚C (75˚F)
Heating :Indoor			: D.B. 20˚C(68˚F)		Outdoor	: D.B. 7˚C(45˚F),		W.B. 6˚C (43˚F)
Refrigerant piping length (one way) : 5m (16ft)
2. Guaranteed operating range							w1 : ( ) Shows the total rating.
				Indoor	Outdoor
							w2 : < > Shows the only booster heater rating.
		Upper limit		D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
	Cooling
		Lower limit		D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
	Heating	Upper limit		D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
		Lower limit		D.B. 17˚C	D.B. -11˚C, W.B. -12˚C
3. Above data based on indicated voltage
	Indoor Unit		1 phase 240V 50Hz
	Outdoor Unit		1 phase 240V 50Hz / 3 phase 415V 50Hz

11

Service Ref.	With Electric heater	PLH-P4KAH
Item	Without Electric heater	PLA-P4KA

	Function						Cooling	Heating
	Capacity		w1			Btu/h	33,100	36,200(43,300)
						W	9,700	10,600(12,700)
	Total input		w1			kW	3.57	3.75(5.85)
		Service Ref.			With Electric heater		PLH-P4KAH
					Without Electric heater		PLA-P4KA
		Power supply(phase, cycle,voltage)					Single, 50Hz, 220-240V
			Input	w2		kW	0.21	0.21<2.10>
			Running current	w2		A	0.99	0.99<8.75>
			Starting current	w2		A	1.38	1.38<8.75>
		External finish					Galvanized sheets with gray heat insulation
	UNIT	Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Turbo fan (direct) x 1
			Fan motor output			kW	0.090
	INDOOR
			Airflow(Lo-Mi1-Mi2-Hi)			m3/min(CFM)	19.5-21.5-24-26(688-759-847-918)
			External static pressure			Pa(mmAq)	0(direct blow)
		Booster heater		w2		kW	<2.1>
		Operation control & Thermostat					Remote controller & built-in
		Noise level(Lo-Mi1-Mi2-Hi)				dB	34-36-39-42
		Unit drain pipe I.D.				mm(in.)	32(1-1/4)
		Dimensions			W	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					D	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					H	mm(in.)	UNIT : 290(11)	PANEL : 30(1-1/8)
		Weight	With Electric heater			kg(lbs)	UNIT : 31(68)	PANEL : 5(11)
			Without Electric heater			kg(lbs)	UNIT : 29(64) PANEL : 5(11)
		Service Ref.					PUH-P4YGA
		Power supply (phase, cycle, voltage)					3-ph, 50Hz, 380-415V (4wires)
			Input			kW	3.36	3.54
			Running current			A	5.49	5.79
			Starting current			A	45
		External finish					Munsell 5Y 8/1
		Refrigerant control					Linear Expansion Valve
		Compressor					Hermetic
	UNIT		Model				NE56YDJM
			Motor output			kW	2.7
			Starter type				Line start
	OUTDOOR
			Protection devices				Anti-phase protector, Thermal relay, Discharge thermo, HP switch
		Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Propeller (direct) x 2
			Fan motor output			kW	0.070+0.070
			Airflow			m3/min(CFM)	85(3,000)
			Crankcase heater			W	38
		Defrost method					Reverse cycle
		Noise level		Cooling		dB	51
				Heating		dB	53
		Dimensions			W	mm(in.)	900(35-7/16)
					D	mm(in.)	330+20(13+3/4)
					H	mm(in.)	1,260 (49-5/8)
		Weight				kg(lbs)	96(212)
	PIPING	Refrigerant					R407C
			Charge			kg(lbs)	4.0(8.8)
			Oil (Model)	Liquid		L	1.6 (Ester)MEL56
	REFRIGERANT	Pipe size O.D.				mm(in.)	9.52 (3/8)
				Gas		mm(in.)	19.05 (3/4)
		Connection method		Indoor side			Flared
				Outdoor side			Flared
		Between the indoor &		Height difference			Max. 50m
		outdoor unit		Piping length			Max. 50m

Notes1. Rating Conditions (ISO T1)
Cooling : Indoor			: D.B. 27˚C(80˚F), W.B. 19˚C (66˚F) Outdoor			: D.B. 35˚C(95˚F),		W.B. 24˚C (75˚F)
Heating :Indoor			: D.B. 20˚C(68˚F)		Outdoor	: D.B. 7˚C(45˚F),		W.B. 6˚C (43˚F)
Refrigerant piping length (one way) : 5m (16ft)
2. Guaranteed operating range							w1 : ( ) Shows the total rating.
				Indoor	Outdoor
							w2 : < > Shows the only booster heater rating.
		Upper limit		D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
	Cooling
		Lower limit		D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
	Heating	Upper limit		D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
		Lower limit		D.B. 17˚C	D.B. -11˚C, W.B. -12˚C
3. Above data based on indicated voltage
	Indoor Unit		1 phase 240V 50Hz
	Outdoor Unit		3 phase 415V 50Hz

12

Service Ref.	With Electric heater	PLH-P5KAH
Item	Without Electric heater	PLA-P5KA

	Function						Cooling	Heating
	Capacity		w1			Btu/h	43,700	52,900(63,100)
						W	12,800	15,500(18,500)
	Total input		w1			kW	5.47	5.69(8.69)
		Service Ref.			With Electric heater		PLH-P5KAH
					Without Electric heater		PLA-P5KA
		Power supply(phase, cycle,voltage)					Single, 50Hz, 220-240V
			Input	w2		kW	0.22	0.22<3.00>
			Running current	w2		A	1.04	1.04<12.50>
			Starting current	w2		A	1.38	1.38<12.50>
		External finish					Galvanized sheets with gray heat insulation
	UNIT	Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Turbo fan (direct) x 1
			Fan motor output			kW	0.090
	INDOOR
			Airflow(Lo-Mi1-Mi2-Hi)			m3/min(CFM)	22.5-25-27.5-30(794-883-971-1,059)
			External static pressure			Pa(mmAq)	0(direct blow)
		Booster heater		w2		kW	<3.0>
		Operation control & Thermostat					Remote controller & built-in
		Noise level(Lo-Mi1-Mi2-Hi)				dB	36-38-40-43
		Unit drain pipe I.D.				mm(in.)	32(1-1/4)
		Dimensions			W	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					D	mm(in.)	UNIT : 1,360(54) PANEL : 1,470(58)
					H	mm(in.)	UNIT : 290(11)	PANEL : 30(1-1/8)
		Weight	With Electric heater			kg(lbs)	UNIT : 39(86)	PANEL : 9(20)
			Without Electric heater			kg(lbs)	UNIT : 37(82) PANEL : 9(20)
		Service Ref.					PUH-P5YGA
		Power supply (phase, cycle, voltage)					3-ph, 50Hz, 380-415V (4wires)
			Input			kW	5.25	5.47
			Running current			A	8.39	8.74
			Starting current			A	79
		External finish					Munsell 5Y 8/1
		Refrigerant control					Linear Expansion Valve
		Compressor					Hermetic
	UNIT		Model				HE86YAA
			Motor output			kW	4.3
			Starter type				Line start
	OUTDOOR
			Protection devices				Internal thermostat, Anti-phase protector, Thermal relay, HP switch, LP switch, Discharge thermo.
		Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Propeller (direct) x 2
			Fan motor output			kW	0.075+0.075
			Airflow			m3/min(CFM)	95(3,360)
			Crankcase heater			W	38
		Defrost method					Reverse cycle
		Noise level		Cooling		dB	53
				Heating		dB	55
		Dimensions			W	mm(in.)	1,050(41-5/16)
					D	mm(in.)	330+20(13+3/4)
					H	mm(in.)	1,260 (49-5/8)
		Weight				kg(lbs)	122(269)
	PIPING	Refrigerant					R407C
			Charge			kg(lbs)	5.8(12.8)
			Oil (Model)	Liquid		L	2.0 (Ester)MEL32
	REFRIGERANT	Pipe size O.D.				mm(in.)	9.52 (3/8)
				Gas		mm(in.)	19.05 (3/4)
		Connection method		Indoor side			Flared
				Outdoor side			Flared
		Between the indoor &		Height difference			Max. 50m
		outdoor unit		Piping length			Max. 50m

Notes1. Rating Conditions (ISO T1)
Cooling : Indoor			: D.B. 27˚C(80˚F), W.B. 19˚C (66˚F) Outdoor			: D.B. 35˚C(95˚F),		W.B. 24˚C (75˚F)
Heating :Indoor			: D.B. 20˚C(68˚F)		Outdoor	: D.B. 7˚C(45˚F),		W.B. 6˚C (43˚F)
Refrigerant piping length (one way) : 5m (16ft)
2. Guaranteed operating range							w1 : ( ) Shows the total rating.
				Indoor	Outdoor
							w2 : < > Shows the only booster heater rating.
		Upper limit		D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
	Cooling
		Lower limit		D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
	Heating	Upper limit		D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
		Lower limit		D.B. 17˚C	D.B. -11˚C, W.B. -12˚C
3. Above data based on indicated voltage
	Indoor Unit		1 phase 240V 50Hz
	Outdoor Unit		3 phase 415V 50Hz

13

Service Ref.	With Electric heater	PLH-P6KAH
Item	Without Electric heater	PLA-P6KA

	Function						Cooling	Heating
	Capacity		w1			Btu/h	48,800	57,300(67,600)
						W	14,300	16,800(19,800)
	Total input		w1			kW	6.58	6.65(9.65)
		Service Ref.			With Electric heater		PLH-P6KAH
					Without Electric heater		PLA-P6KA
		Power supply(phase, cycle,voltage)					Single, 50Hz, 220-240V (4wires)
			Input	w2		kW	0.22	0.22<3.00>
			Running current	w2		A	1.04	1.04<12.50>
			Starting current	w2		A	1.38	1.38<12.50>
		External finish					Galvanized sheets with gray heat insulation
	UNIT	Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Turbo fan (direct) x 1
			Fan motor output			kW	0.090
	INDOOR
			Airflow(Lo-Mi1-Mi2-Hi)			m3/min(CFM)	25-27.5-30-33(883-971-1,059-1,165)
			External static pressure			Pa(mmAq)	0(direct blow)
		Booster heater		w2		kW	<3.0>
		Operation control & Thermostat					Remote controller & built-in
		Noise level(Lo-Mi1-Mi2-Hi)				dB	38-40-42-45
		Unit drain pipe I.D.				mm(in.)	32(1-1/4)
		Dimensions			W	mm(in.)	UNIT : 840(33) PANEL : 950(37)
					D	mm(in.)	UNIT : 1,360(54) PANEL : 1,470(58)
					H	mm(in.)	UNIT : 290(11)	PANEL : 38(1-1/8)
		Weight	With Electric heater			kg(lbs)	UNIT : 39(86)	PANEL : 9(20)
			Without Electric heater			kg(lbs)	UNIT : 37(82) PANEL : 9(20)
		Service Ref.					PUH-P6YGA
		Power supply (phase, cycle, voltage)					3-ph, 50Hz, 380-415V (4wires)
			Input			kW	6.36	6.43
			Running current			A	10.17	10.28
			Starting current			A	84
		External finish					Munsell 5Y 8/1
		Refrigerant control					Linear Expansion Valve
		Compressor					Hermetic
	UNIT		Model				HE101YAA
			Motor output			kW	5.1
			Starter type				Line start
	OUTDOOR
			Protection devices				Internal thermostat, Anit-phase protector, Thermal relay, HP switch, LP switch, Discharge thermo.
		Heat exchanger					Plate fin coil
		Fan	Fan(drive) x No.				Propeller (direct) x 2
			Fan motor output			kW	0.075+0.075
			Airflow			m3/min(CFM)	100(3,530)
			Crankcase heater			W	38
		Defrost method					Reverse cycle
		Noise level		Cooling		dB	55
				Heating		dB	57
		Dimensions			W	mm(in.)	1,050(41-5/16)
					D	mm(in.)	330+20(13+3/4)
					H	mm(in.)	1,260 (49-5/8)
		Weight				kg(lbs)	122(269)
	PIPING	Refrigerant					R407C
			Charge			kg(lbs)	5.8(12.8)
			Oil (Model)	Liquid		L	2.0 (Ester)MEL32
	REFRIGERANT	Pipe size O.D.				mm(in.)	9.52 (3/8)
				Gas		mm(in.)	19.05 (3/4)
		Connection method		Indoor side			Flared
				Outdoor side			Flared
		Between the indoor &		Height difference			Max. 50m
		outdoor unit		Piping length			Max. 50m

Notes1. Rating Conditions (ISO T1)
Cooling : Indoor			: D.B. 27˚C(80˚F), W.B. 19˚C (66˚F) Outdoor			: D.B. 35˚C(95˚F),		W.B. 24˚C (75˚F)
Heating :Indoor			: D.B. 20˚C(68˚F)		Outdoor	: D.B. 7˚C(45˚F),		W.B. 6˚C (43˚F)
Refrigerant piping length (one way) : 5m (16ft)
2. Guaranteed operating range							w1 : ( ) Shows the total rating.
				Indoor	Outdoor
							w2 : < > Shows the only booster heater rating.
		Upper limit		D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
	Cooling
		Lower limit		D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
	Heating	Upper limit		D.B. 28˚C	D.B. 24˚C, W.B. 18˚C
		Lower limit		D.B. 17˚C	D.B. -11˚C, W.B. -12˚C
3. Above data based on indicated voltage
	Indoor Unit		1 phase 240V 50Hz
	Outdoor Unit		3 phase 415V 50Hz

14

2.Cooling only type

Item				Service Ref.	PLA-P1.6KA	PLA-P2KA
Function					Cooling	Cooling
Capacity				Btu/h	15,000	18,400
				W	4,400	5,400
Total input
				kW	1.86	2.62
	Service Ref.				PLA-P1.6KA	PLA-P2KA
	Power supply(phase, cycle,voltage)				Single, 50Hz, 220-240V
		Input		kW	0.15	0.14
		Running current		A	0.64	0.65
		Starting current		A	0.70	0.72
	External finish				Galvanized sheets with gray heat insulation
UNIT	Heat exchanger					Plate fin coil
	Fan	Fan(drive) x No.			Turbo fan (direct) x 1
INDOOR		Fan motor output		kW		0.030
		Airflow(Lo-Mi1-Mi2-Hi)		K/min(CFM)	13-14-15-16(459-494-530-565)
		External static pressure		Pa(mmAq)		0(direct blow)
	Booster heater			kW		—
	Operation control & Thermostat				Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)			dB		32-34-35.5-37
	Unit drain pipe I.D.			mm(in.)		32(1-1/4)
	Dimensions		W	mm(in.)	UNIT : 660(26), PANEL : 760(30)
			D	mm(in.)	UNIT : 660(26), PANEL : 760(30)
	Weight		H	mm(in.)	UNIT : 253(10), PANEL : 30(1-1/8)
				kg(lbs)	UNIT : 19(42), PANEL : 3.7(8)
	Service Ref.				PU-P1.6VGA	PU-P2VGA
	Power supply (phase, cycle, voltage)				Single, 50Hz, 220-240V
		Input		kW	1.71	2.48
		Running current		A	7.66	11.11
		Starting current		A	36	74
	External finish					Munsell 5Y 8/1
	Refrigerant control				Linear Expansion Valve
	Compressor					Hermetic
UNIT		Model			RE277VHSM	NE38VMJM
		Motor output		kW	1.3	1.7
OUTDOOR		Starter type				Line start
		Protection devices			Inner thermostat, High pressure switch,Discharge thermo.
	Heat exchanger					Plate fin coil
	Fan	Fan(drive) x No.			Propeller (direct) x 1
		Fan motor output		kW		0.070
		Airflow		K/min(CFM)	45(1,590)	55(1,940)
		Crankcase heater		W	30	38
	Defrost method					—
	Noise level		Cooling	dB	46	48
	Dimensions		W	mm(in.)		900(35-7/16)
			D	mm(in.)	330+20(13+3/4)
			H	mm(in.)	650 (25-5/8)	855(33-5/8)
	Weight			kg(lbs)	55(121)	71(157)
PIPING	Refrigerant					R407C
		Charge		kg(lbs)	2.6(5.7)	3.1(6.8)
		Oil (Model)	Liquid	L	0.57(Ester)MEL56	1.2(Ester)MEL56
REFRIGERANT	Pipe size O.D.			mm(in.)		9.52 (3/8)
			Gas	mm(in.)		15.88 (5/8)
	Connection method		Indoor side			Flared
			Outdoor side			Flared
	Between the indoor &		Height difference			Max. 40m
	outdoor unit		Piping length			Max. 40m
Notes1. Rating Conditions (ISO T1)
	Cooling : Indoor : D.B. 27˚C(80˚F),			W.B. 19˚C (66˚F)	Outdoor : D.B. 35˚C(95˚F),	W.B. 24˚C (75˚F)
	Refrigerant piping length (one way) : 5m (16ft)
	2. Guaranteed operating range
			Indoor		Outdoor
	Cooling Upper limit		D.B. 35˚C, W.B. 22.5˚C		D.B. 46˚C
		Lower limit	D.B. 19˚C, W.B. 15˚C		D.B. -5˚C

3. Above data based on indicated voltage Indoor Unit 1 phase 240V 50Hz Outdoor Unit 1 phase 240V 50Hz

15

Item				Service Ref.	PLA-P2.5KA	PLA-P3KA
Function					Cooling	Cooling
Capacity				Btu/h	21,500	26,300
				W	6,300	7,700
Total input
				kW	2.77	3.47
	Service Ref.				PLA-P2.5KA	PLA-P3KA
	Power supply(phase, cycle,voltage)				Single, 50Hz, 220-240V
		Input		kW	0.14	0.13
		Running current		A	0.61	0.62
		Starting current		A	0.67	0.91
	External finish				Galvanized sheets with gray heat insulation
UNIT	Heat exchanger				Plate fin coil
	Fan	Fan(drive) x No.			Turbo fan (direct) x 1
INDOOR		Fan motor output		kW	0.030	0.070
		Airflow(Lo-Mi1-Mi2-Hi)		K/min(CFM)	14-15-16-17 (494-530-565-600)	15-16.5-18.5-20 (530-582-653-706)
		External static pressure		Pa(mmAq)	0(direct blow)
	Booster heater			kW		—
	Operation control & Thermostat				Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)			dB	35-36.5-38-39.5	32-34-37-39
	Unit drain pipe I.D.			mm(in.)	32(1-1/4)
	Dimensions		W	mm(in.)	UNIT : 660(26), PANEL : 760(30)	UNIT : 840(33), PANEL : 950(37)
			D	mm(in.)	UNIT : 660(26), PANEL : 760(30)	UNIT : 840(33), PANEL : 950(37)
	Weight		H	mm(in.)	UNIT : 253(10), PANEL : 30(1-1/8)	UNIT : 290(11), PANEL : 30(1-1/8)
				kg(lbs)	UNIT : 20(44), PANEL : 3.7(8)	UNIT : 26(57), PANEL : 5(11)
	Service Ref.				PU-P2.5VGA	PU-P3VGA / YGA
	Power supply (phase, cycle, voltage)				Single, 50Hz, 220-240V	Single, 50Hz, 220-240V / 3-ph, 50Hz, 380-415V(4wires)
		Input		kW	2.63	3.34
		Running current		A	11.78	14.64 / 5.46
		Starting current		A	77	93 / 41
	External finish				Munsell 5Y 8/1
	Refrigerant control				Linear Expansion Valve
	Compressor				Hermetic
UNIT		Model			NE41VMJM	NE52VNJM / NE52YDJM
		Motor output		kW	1.9	2.5
OUTDOOR		Starter type			Line start
		Protection devices			Internal thermostat, High switch,Discharge thermo. / Thermal rely, Discharge thermo, HP switch, Anti-phase protector.
	Heat exchanger				Plate fin coil
	Fan	Fan(drive) x No.			Propeller (direct) x 1
		Fan motor output		kW	0.070
		Airflow		K/min(CFM)	50(1,770)
		Crankcase heater		W		38
	Defrost method					—
	Noise level		Cooling	dB	48	49
	Dimensions		W	mm(in.)	900(35-7/16)
			D	mm(in.)	330+20(13+3/4)
			H	mm(in.)	855(33-5/8)
	Weight			kg(lbs)	82(181)
PIPING	Refrigerant				R407C
		Charge		kg(lbs)	3.3(7.3)	3.7(8.2)
		Oil (Model)	Liquid	L	1.2(Ester)MEL56	1.6(Ester)MEL56
REFRIGERANT	Pipe size O.D.			mm(in.)	9.52 (3/8)
			Gas	mm(in.)	15.88 (5/8)
	Connection method		Indoor side		Flared
			Outdoor side		Flared
	Between the indoor &		Height difference		Max. 50m
	outdoor unit		Piping length		Max. 50m

Notes1. Rating Conditions (ISO T1)
Cooling : Indoor		: D.B. 27˚C(80˚F), W.B. 19˚C (66˚F)		Outdoor : D.B. 35˚C(95˚F), W.B. 24˚C (75˚F)
Refrigerant piping length (one way) : 5m (16ft)
2. Guaranteed operating range
			Indoor	Outdoor
Cooling	Upper limit		D.B. 35˚C, W.B. 22.5˚C	D.B. 46˚C
	Lower limit		D.B. 19˚C, W.B. 15˚C	D.B. -5˚C
3. Above data based on indicated voltage
Indoor Unit		1 phase 240V 50Hz
Outdoor Unit		1 phase 240V 50Hz / 3 phase 415V 50Hz

16

Item						Service Ref.			PLA-P4KA
Function									Cooling
Capacity						Btu/h		33,100
						W		9,700
Total input						kW		3.57
	Service Ref.								PLA-P4KA
	Power supply(phase, cycle,voltage)								Single, 50Hz, 220-240V
		Input				kW		0.21
		Running current				A		0.99
		Starting current				A		1.38
	External finish								Galvanized sheets with gray heat insulation
UNIT	Heat exchanger								Plate fin coil
	Fan	Fan(drive) x No.							Turbo fan (direct) x 1
INDOOR		Fan motor output				kW		0.090
		Airflow(Lo-Mi1-Mi2-Hi)				K/min(CFM)		19.5-21.5-24-26(688-759-847-918)
		External static pressure				Pa(mmAq)			0(direct blow)
	Booster heater					kW			—
	Operation control & Thermostat								Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)					dB		34-36-39-42
	Unit drain pipe I.D.					mm(in.)		32(1-1/4)
	Dimensions				W	mm(in.)			UNIT : 840(33), PANEL : 950(37)
					D	mm(in.)			UNIT : 840(33), PANEL : 950(37)
	Weight				H	mm(in.)			UNIT : 290(11), PANEL : 30(1-1/8)
						kg(lbs)			UNIT : 29(64), PANEL : 5(11)
	Service Ref.								PU-P4YGA
	Power supply (phase, cycle, voltage)								3-ph, 50Hz, 380-415V (4wires)
		Input				kW		3.36
		Running current				A		5.49
		Starting current				A		45
	External finish								Munsell 5Y 8/1
	Refrigerant control								Linear Expansion Valve
	Compressor								Hermetic
UNIT		Model							NE56YDJM
		Motor output				kW		2.7
OUTDOOR		Starter type							Line start
		Protection devices						Anti-phase protector, Thermal relay, Discharge thermo, HP switch
	Heat exchanger								Plate fin coil
	Fan	Fan(drive) x No.							Propeller (direct) x 2
		Fan motor output				kW		0.070+0.070
		Airflow				K/min(CFM)		85(3,000)
		Crankcase heater				W		38
	Defrost method								—
	Noise level				Cooling	dB		51
	Dimensions				W	mm(in.)		900(35-7/16)
					D	mm(in.)		330+20(13+3/4)
					H	mm(in.)		1,260 (49-5/8)
	Weight					kg(lbs)		96(212)
PIPING	Refrigerant								R407C
		Charge				kg(lbs)		4.0(8.8)
		Oil (Model)			Liquid	L			1.6 (Ester)MEL56
REFRIGERANT	Pipe size O.D.					mm(in.)		9.52 (3/8)
					Gas	mm(in.)		19.05 (3/4)
	Connection method				Indoor side				Flared
					Outdoor side				Flared
	Between the indoor &				Height difference				Max. 50m
	outdoor unit				Piping length				Max. 50m
Notes1. Rating Conditions (ISO T1)
	Cooling : Indoor : D.B. 27˚C(80˚F),					W.B. 19˚C (66˚F)		Outdoor : D.B. 35˚C(95˚F), W.B. 24˚C (75˚F)
	Refrigerant piping length (one way) : 5m (16ft)
	2. Guaranteed operating range
					Indoor			Outdoor
	Cooling		Upper limit		D.B. 35˚C, W.B. 22.5˚C			D.B. 46˚C
			Lower limit		D.B. 19˚C, W.B. 15˚C			D.B. -5˚C

3. Above data based on indicated voltage Indoor Unit 1 phase 240V 50Hz Outdoor Unit 3 phase 415V 50Hz

17

Item					Service Ref.		PLA-P5KA	PLA-P6KA
Function							Cooling	Cooling
Capacity					Btu/h		43,700	48,800
					W		12,800	14,300
Total input
					kW		5.47	6.58
	Service Ref.						PLA-P5KA	PLA-P6KA
	Power supply(phase, cycle,voltage)						Single, 50Hz, 220-240V
		Input			kW		0.22	0.22
		Running current			A		1.04	1.04
		Starting current			A		1.38	1.38
	External finish						Galvanized sheets with gray heat insulation
UNIT	Heat exchanger						Plate fin coil
	Fan	Fan(drive) x No.					Turbo fan (direct) x 1
INDOOR		Fan motor output			kW		0.090
		Airflow(Lo-Mi1-Mi2-Hi)			K/min(CFM)		22.5-25-27.5-30(794-883-971-1,059)	25-27.5-30-33(883-971-1,059-1,165)
		External static pressure			Pa(mmAq)		0(direct blow)
	Booster heater				kW			—
	Operation control & Thermostat						Remote controller & built-in
	Noise level(Lo-Mi1-Mi2-Hi)				dB		36-38-40-43	38-40-43-45
	Unit drain pipe I.D.				mm(in.)		32(1-1/4)
	Dimensions			W	mm(in.)		UNIT : 840(33), PANEL : 950(37)
				D	mm(in.)		UNIT : 1,360(54), PANEL : 1,470(58)
	Weight			H	mm(in.)		UNIT : 290(11), PANEL : 30(1-1/8)
					kg(lbs)		UNIT : 37(82),	PANEL : 9(20)
	Service Ref.						PU-P5YGA	PU-P6YGA
	Power supply (phase, cycle, voltage)						3-ph, 50Hz, 380-415V (4wires)
		Input			kW		5.25	6.36
		Running current			A		8.39	10.17
		Starting current			A		79	84
	External finish						Munsell 5Y 8/1
	Refrigerant control						Linear Expansion Valve
	Compressor						Hermetic
UNIT		Model					HE86YAA	HE101YAA
		Motor output			kW		4.3	5.1
OUTDOOR		Starter type					Line start
		Protection devices				Internal thermostat, Anti-phase protector, Thermal relay, HP switch, LP switch, Discharge thermo.
	Heat exchanger						Plate fin coil
	Fan	Fan(drive) x No.					Propeller (direct) x 2
		Fan motor output			kW		0.075+0.075
		Airflow			K/min(CFM)		95(3,360)	100(3,530)
		Crankcase heater			W			38
	Defrost method							—
	Noise level			Cooling	dB		53	57
	Dimensions			W	mm(in.)		1,050(41-5/16)
				D	mm(in.)		330+20(13+3/4)
				H	mm(in.)		1,260 (49-5/8)
	Weight				kg(lbs)		122(269)
PIPING	Refrigerant						R407C
		Charge			kg(lbs)		5.8(12.8)
		Oil (Model)		Liquid	L		2.0 (Ester)MEL32
REFRIGERANT	Pipe size O.D.				mm(in.)		9.52 (3/8)
				Gas	mm(in.)		19.05 (3/4)
	Connection method			Indoor side			Flared
				Outdoor side			Flared
	Between the indoor &			Height difference			Max. 50m
	outdoor unit			Piping length			Max. 50m
Notes1. Rating Conditions (ISO T1)
	Cooling : Indoor : D.B. 27˚C(80˚F),				W.B. 19˚C (66˚F)		Outdoor : D.B. 35˚C(95˚F), W.B. 24˚C (75˚F)
	Refrigerant piping length (one way) : 5m (16ft)
	2. Guaranteed operating range
				Indoor			Outdoor
	Cooling		Upper limit	D.B. 35˚C, W.B. 22.5˚C			D.B. 46˚C
			Lower limit	D.B. 19˚C, W.B. 15˚C			D.B. -5˚C

3. Above data based on indicated voltage Indoor Unit 1 phase 240V 50Hz Outdoor Unit 3 phase 415V 50Hz

18

5 DATA

1.PERFORMANCE DATA

1)COOLING CAPACITY(1) PLH-P1.6KAH, PLA-P1.6KA

Indoor		Indoor						Outdoor intake air D.B.(°C)
				20					25					30
Intake air		Intake air
D.B.(°C)		W.B.(°C)	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.
20		16	4356	3049		0.70	1.49	4224	2957		0.70	1.57	4092	2864		0.70	1.66
20		18	4664	2705		0.58	1.52	4532	2629		0.58	1.60	4378	2539		0.58	1.71
20		20	5016	2307		0.46	1.56	4906	2257		0.46	1.64	4774	2196		0.46	1.75
22		16	4356	3398		0.78	1.49	4224	3296		0.78	1.57	4092	3192		0.78	1.66
22		18	4664	3078		0.66	1.52	4532	2991		0.66	1.60	4378	2889		0.66	1.71
22		20	5016	2709		0.54	1.56	4906	2649		0.54	1.64	4774	2578		0.54	1.75
24		16	4356	3746		0.86	1.49	4224	3633		0.86	1.57	4092	3519		0.86	1.66
24		18	4664	3451		0.74	1.52	4532	3354		0.74	1.60	4378	3240		0.74	1.71
24		20	5016	3110		0.62	1.56	4906	3042		0.62	1.64	4774	2960		0.62	1.75
24		22	5346	2673		0.50	1.60	5236	2618		0.50	1.69	5104	2552		0.50	1.80
26		16	4356	4095		0.94	1.49	4224	3971		0.94	1.57	4092	3846		0.94	1.66
26		18	4664	3824		0.82	1.52	4532	3716		0.82	1.60	4378	3590		0.82	1.71
26		20	5016	3511		0.70	1.56	4906	3434		0.70	1.64	4774	3342		0.70	1.75
26		22	5346	3101		0.58	1.60	5236	3037		0.58	1.69	5104	2960		0.58	1.80
28		16	4356	4356		1.00	1.49	4224	4224		1.00	1.57	4092	4092		1.00	1.66
28		18	4664	4198		0.90	1.52	4532	4079		0.90	1.60	4378	3940		0.90	1.71
28		20	5016	3912		0.78	1.56	4906	3827		0.78	1.64	4774	3724		0.78	1.75
28		22	5346	3528		0.66	1.60	5236	3456		0.66	1.69	5104	3369		0.66	1.80
30		16	4356	4356		1.00	1.49	4224	4224		1.00	1.57	4092	4092		1.00	1.66
30		18	4664	4571		0.98	1.52	4532	4441		0.98	1.60	4378	4290		0.98	1.71
30		20	5016	4314		0.86	1.56	4906	4219		0.86	1.64	4774	4106		0.86	1.75
30		22	5346	3956		0.74	1.60	5236	3875		0.74	1.69	5104	3777		0.74	1.80
32		16	4356	4356		1.00	1.49	4224	4224		1.00	1.57	4092	4092		1.00	1.66
32		18	4664	4664		1.00	1.52	4532	4532		1.00	1.60	4378	4378		1.00	1.71
32		20	5016	4715		0.94	1.56	4906	4612		0.94	1.64	4774	4488		0.94	1.75
32		22	5346	4384		0.82	1.60	5236	4294		0.82	1.69	5104	4185		0.82	1.80
34		16	4356	4356		1.00	1.49	4224	4224		1.00	1.57	4092	4092		1.00	1.66
34		18	4664	4664		1.00	1.52	4532	4532		1.00	1.60	4378	4378		1.00	1.71
34		20	5016	5016		1.00	1.56	4906	4906		1.00	1.64	4774	4774		1.00	1.75
34		22	5346	4811		0.90	1.60	5236	4712		0.90	1.69	5104	4594		0.90	1.80
Note CA	: Capacity (W)						SHC(W) : Sensible heat capacity
P.C. : Power consumption (kW)							SHF : Sensible heat factor

19

COOLING CAPACITY(2)

PLH-P1.6KAH, PLA-P1.6KA

Indoor		Indoor						Outdoor intake air D.B.(°C)
				35					40					45
Intake air		Intake air
D.B.(°C)		W.B.(°C)	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.
20		16	3916	2741		0.70	1.79	3740	2618		0.70	1.92	3652	2556		0.70	2.01
20		18	4224	2450		0.58	1.83	4092	2373		0.58	1.97	3960	2297		0.58	2.06
20		20	4576	2105		0.46	1.88	4400	2024		0.46	2.01	4268	1963		0.46	2.10
22		16	3916	3054		0.78	1.79	3740	2917		0.78	1.92	3652	2849		0.78	2.01
22		18	4224	2788		0.66	1.83	4092	2701		0.66	1.97	3960	2614		0.66	2.06
22		20	4576	2471		0.54	1.88	4400	2376		0.54	2.01	4268	2305		0.54	2.10
24		16	3916	3368		0.86	1.79	3740	3216		0.86	1.92	3652	3141		0.86	2.01
24		18	4224	3126		0.74	1.83	4092	3028		0.74	1.97	3960	2930		0.74	2.06
24		20	4576	2837		0.62	1.88	4400	2728		0.62	2.01	4268	2646		0.62	2.10
24		22	4928	2464		0.50	1.92	4752	2376		0.50	2.06	4620	2310		0.50	2.16
26		16	3916	3681		0.94	1.79	3740	3516		0.94	1.92	3652	3433		0.94	2.01
26		18	4224	3464		0.82	1.83	4092	3355		0.82	1.97	3960	3247		0.82	2.06
26		20	4576	3203		0.70	1.88	4400	3080		0.70	2.01	4268	2988		0.70	2.10
26		22	4928	2858		0.58	1.92	4752	2756		0.58	2.06	4620	2680		0.58	2.16
28		16	3916	3916		1.00	1.79	3740	3740		1.00	1.92	3652	3652		1.00	2.01
28		18	4224	3802		0.90	1.83	4092	3683		0.90	1.97	3960	3564		0.90	2.06
28		20	4576	3569		0.78	1.88	4400	3432		0.78	2.01	4268	3329		0.78	2.10
28		22	4928	3252		0.66	1.92	4752	3136		0.66	2.06	4620	3049		0.66	2.16
30		16	3916	3916		1.00	1.79	3740	3740		1.00	1.92	3652	3652		1.00	2.01
30		18	4224	4140		0.98	1.83	4092	4010		0.98	1.97	3960	3881		0.98	2.06
30		20	4576	3935		0.86	1.88	4400	3784		0.86	2.01	4268	3670		0.86	2.10
30		22	4928	3647		0.74	1.92	4752	3516		0.74	2.06	4620	3419		0.74	2.16
32		16	3916	3916		1.00	1.79	3740	3740		1.00	1.92	3652	3652		1.00	2.01
32		18	4224	4224		1.00	1.83	4092	4092		1.00	1.97	3960	3960		1.00	2.06
32		20	4576	4301		0.94	1.88	4400	4136		0.94	2.01	4268	4012		0.94	2.10
32		22	4928	4041		0.82	1.92	4752	3897		0.82	2.06	4620	3788		0.82	2.16
34		16	3916	3916		1.00	1.79	3740	3740		1.00	1.92	3652	3652		1.00	2.01
34		18	4224	4224		1.00	1.83	4092	4092		1.00	1.97	3960	3960		1.00	2.06
34		20	4576	4576		1.00	1.88	4400	4400		1.00	2.01	4268	4268		1.00	2.10
34		22	4928	4435		0.90	1.92	4752	4277		0.90	2.06	4620	4158		0.90	2.16
Note CA	: Capacity (W)						SHC(W) : Sensible heat capacity
P.C. : Power consumption (kW)							SHF : Sensible heat factor

20

COOLING CAPACITY(3)

PLH-P2KAH, PLA-P2KA

Indoor		Indoor						Outdoor intake air D.B.(°C)
				20					25					30
Intake air		Intake air
D.B.(°C)		W.B.(°C)	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.
20		16	5346	3421		0.64	2.10	5184	3318		0.64	2.21	5022	3214		0.64	2.34
20		18	5724	2976		0.52	2.14	5562	2892		0.52	2.25	5373	2794		0.52	2.41
20		20	6156	2462		0.40	2.20	6021	2408		0.40	2.31	5859	2344		0.40	2.46
22		16	5346	3849		0.72	2.10	5184	3732		0.72	2.21	5022	3616		0.72	2.34
22		18	5724	3434		0.60	2.14	5562	3337		0.60	2.25	5373	3224		0.60	2.41
22		20	6156	2955		0.48	2.20	6021	2890		0.48	2.31	5859	2812		0.48	2.46
24		16	5346	4277		0.80	2.10	5184	4147		0.80	2.21	5022	4018		0.80	2.34
24		18	5724	3892		0.68	2.14	5562	3782		0.68	2.25	5373	3654		0.68	2.41
24		20	6156	3447		0.56	2.20	6021	3372		0.56	2.31	5859	3281		0.56	2.46
24		22	6561	2887		0.44	2.25	6426	2827		0.44	2.38	6264	2756		0.44	2.54
26		16	5346	4704		0.88	2.10	5184	4562		0.88	2.21	5022	4419		0.88	2.34
26		18	5724	4350		0.76	2.14	5562	4227		0.76	2.25	5373	4083		0.76	2.41
26		20	6156	3940		0.64	2.20	6021	3853		0.64	2.31	5859	3750		0.64	2.46
26		22	6561	3412		0.52	2.25	6426	3342		0.52	2.38	6264	3257		0.52	2.54
28		16	5346	5132		0.96	2.10	5184	4977		0.96	2.21	5022	4821		0.96	2.34
28		18	5724	4808		0.84	2.14	5562	4672		0.84	2.25	5373	4513		0.84	2.41
28		20	6156	4432		0.72	2.20	6021	4335		0.72	2.31	5859	4218		0.72	2.46
28		22	6561	3937		0.60	2.25	6426	3856		0.60	2.38	6264	3758		0.60	2.54
30		16	5346	5346		1.00	2.10	5184	5184		1.00	2.21	5022	5022		1.00	2.34
30		18	5724	5266		0.92	2.14	5562	5117		0.92	2.25	5373	4943		0.92	2.41
30		20	6156	4925		0.80	2.20	6021	4817		0.80	2.31	5859	4687		0.80	2.46
30		22	6561	4461		0.68	2.25	6426	4370		0.68	2.38	6264	4260		0.68	2.54
32		16	5346	5346		1.00	2.10	5184	5184		1.00	2.21	5022	5022		1.00	2.34
32		18	5724	5724		1.00	2.14	5562	5562		1.00	2.25	5373	5373		1.00	2.41
32		20	6156	5417		0.88	2.20	6021	5298		0.88	2.31	5859	5156		0.88	2.46
32		22	6561	4986		0.76	2.25	6426	4884		0.76	2.38	6264	4761		0.76	2.54
34		16	5346	5346		1.00	2.10	5184	5184		1.00	2.21	5022	5022		1.00	2.34
34		18	5724	5724		1.00	2.14	5562	5562		1.00	2.25	5373	5373		1.00	2.41
34		20	6156	5910		0.96	2.20	6021	5780		0.96	2.31	5859	5625		0.96	2.46
34		22	6561	5511		0.84	2.25	6426	5398		0.84	2.38	6264	5262		0.84	2.54
Note CA	: Capacity (W)						SHC(W) : Sensible heat capacity
P.C. : Power consumption (kW)							SHF : Sensible heat factor

21

COOLING CAPACITY(4)

PLH-P2KAH, PLA-P2KA

Indoor		Indoor						Outdoor intake air D.B.(°C)
				35					40					45
Intake air		Intake air
D.B.(°C)		W.B.(°C)	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.	CA	SHC(W)		SHF	P.C.
20		16	4806	3076		0.64	2.52	4590	2938		0.64	2.70	4374	2799		0.64	2.92
20		18	5184	2696		0.52	2.58	5022	2611		0.52	2.78	4698	2443		0.52	2.99
20		20	5616	2246		0.40	2.65	5400	2160		0.40	2.83	5076	2030		0.40	3.04
22		16	4806	3460		0.72	2.52	4590	3305		0.72	2.70	4374	3149		0.72	2.92
22		18	5184	3110		0.60	2.58	5022	3013		0.60	2.78	4698	2819		0.60	2.99
22		20	5616	2696		0.48	2.65	5400	2592		0.48	2.83	5076	2436		0.48	3.04
24		16	4806	3845		0.80	2.52	4590	3672		0.80	2.70	4374	3499		0.80	2.92
24		18	5184	3525		0.68	2.58	5022	3415		0.68	2.78	4698	3195		0.68	2.99
24		20	5616	3145		0.56	2.65	5400	3024		0.56	2.83	5076	2843		0.56	3.04
24		22	6048	2661		0.44	2.70	5832	2566		0.44	2.91	5508	2424		0.44	3.09
26		16	4806	4229		0.88	2.52	4590	4039		0.88	2.70	4374	3849		0.88	2.92
26		18	5184	3940		0.76	2.58	5022	3817		0.76	2.78	4698	3570		0.76	2.99
26		20	5616	3594		0.64	2.65	5400	3456		0.64	2.83	5076	3249		0.64	3.04
26		22	6048	3145		0.52	2.70	5832	3033		0.52	2.91	5508	2864		0.52	3.09
28		16	4806	4614		0.96	2.52	4590	4406		0.96	2.70	4374	4199		0.96	2.92
28		18	5184	4355		0.84	2.58	5022	4218		0.84	2.78	4698	3946		0.84	2.99
28		20	5616	4044		0.72	2.65	5400	3888		0.72	2.83	5076	3655		0.72	3.04
28		22	6048	3629		0.60	2.70	5832	3499		0.60	2.91	5508	3305		0.60	3.09
30		16	4806	4806		1.00	2.52	4590	4590		1.00	2.70	4374	4374		1.00	2.92
30		18	5184	4769		0.92	2.58	5022	4620		0.92	2.78	4698	4322		0.92	2.99
30		20	5616	4493		0.80	2.65	5400	4320		0.80	2.83	5076	4061		0.80	3.04
30		22	6048	4113		0.68	2.70	5832	3966		0.68	2.91	5508	3745		0.68	3.09
32		16	4806	4806		1.00	2.52	4590	4590		1.00	2.70	4374	4374		1.00	2.92
32		18	5184	5184		1.00	2.58	5022	5022		1.00	2.78	4698	4698		1.00	2.99
32		20	5616	4942		0.88	2.65	5400	4752		0.88	2.83	5076	4467		0.88	3.04
32		22	6048	4596		0.76	2.70	5832	4432		0.76	2.91	5508	4186		0.76	3.09
34		16	4806	4806		1.00	2.52	4590	4590		1.00	2.70	4374	4374		1.00	2.92
34		18	5184	5184		1.00	2.58	5022	5022		1.00	2.78	4698	4698		1.00	2.99
34		20	5616	5391		0.96	2.65	5400	5184		0.96	2.83	5076	4873		0.96	3.04
34		22	6048	5080		0.84	2.70	5832	4899		0.84	2.91	5508	4627		0.84	3.09
Note CA	: Capacity (W)						SHC(W) : Sensible heat capacity
P.C. : Power consumption (kW)							SHF : Sensible heat factor

22