Miele PW 5064 Installation Manual [zh]
医用地巾清洗消毒机操作和安装指南
PW 5064 MopStar 60
为避免意外风险和机器损坏，请务
必在安装和首次使用机器前阅读本
指南。
zh - CN
M.-Nr. 09 918 551
环境保护
包装材料的处理
包装的作用是在运输过程中保护机器免
遭损坏。包装使用的均是环保材料，便
于处理，且通常可以回收利用。
回收包装不仅有利于节省生产过程中原
材料的使用量，也可减少垃圾填埋场的
垃圾量。
废旧机器的处理
电气和电子设备通常包含一些有用的材
料，也包含一些（若未妥善处置或处理）
可能对人类健康和环境构成危害的材料。
但这些材料是保证机器正常运行不可缺
少的组成部分。因此，请勿将其与生活
垃圾一起丢弃。
节能窍门
能耗和水耗
— 耗水量和耗电量由负荷高低决定。为
了实现机器的充分利用，请根据您所
用程序允许的最大干燥负荷量进行装填。
清洗剂
— 切勿超出包装上厂商建议的清洗剂用量。
— 负荷减小时减少清洗剂用量。
使用滚筒式烘干机烘干时
若稍后使用滚筒式烘干机烘干，则选择
清洗程序允许的最高脱水转速可节能。
请在当地的废品收集站或回收中心处理
废旧机器，或联系经销商咨询意见。同
时在存储待处理废旧机器时，请确保不
会对儿童造成危害。
2
目录
环境保护
警告和安全须知
医用地巾清洗消毒机操作
控制面板····································································································13
显示屏·······································································································14
首次使用前
正确的操作方法
简要说明····································································································16
脱水
最终脱水的最大转速····················································································21
漂洗和中间脱水··························································································21
省略最终脱水（暂停漂洗）···········································································21
省略漂洗和最终脱水之间的脱水····································································21
延迟启动
程序图表
程序序列
预脱水·······································································································30
预洗 / 预漂洗······························································································30
防皱··········································································································30
改变程序序列
取消程序····································································································31
中断程序····································································································31
修改程序····································································································31
程序开始后添加或取出地巾 / 抹布··································································32
清洗剂
软水剂·······································································································33
地巾 / 抹布柔顺剂或液态粉浆········································································33
染色剂和染料去除剂 / 染料·············································································34
外部分配系统·····························································································35
试剂耗尽报警······························································································37
清洁与养护
清洁机器····································································································38
清洁进水口过滤器·······················································································40
问题解决指南
程序无法启动····························································································· 41
显示屏中的故障信息·····················································································42
····································································································
···························································································
··············································································
·································································································15
··························································································16
··········································································································21
····································································································22
·····································································································23
····································································································29
·····························································································31
·······································································································33
·································································································38
·····························································································41
2
6
13
3
目录
常规问题····································································································43
清洗效果不佳······························································································44
按下开门键无法打开腔门··············································································45
电源中断后继续程序····················································································45
排水口堵塞或断电时打开··············································································46
··········································································································47
售后
计算机 / 光学接口························································································47
可选配件····································································································47
安装与连接
前视图·······································································································48
后视图·······································································································49
安装机器····································································································50
安装表面····································································································51
取下运输杆·································································································51
重新装入运输杆 ··························································································53
将机器水平摆放····························································································53
拧出并调整底座 ··························································································53
固定机器以防止其滑动·················································································54
机器清洗消毒机与烘干机叠放·······································································55
安装于凸起基座上·······················································································55
水连接········································································································56
冷水源连接·································································································56
热水源连接·································································································57
排水连接····································································································57
电器连接····································································································58
单相交流 230 V - 各国不同···········································································59
技术参数
设置菜单
清洗溶液冷却·······························································································62
显示屏对比度·····························································································62
显示屏亮度·································································································62
菜单操作权限设置
输入密码····································································································63
修改密码····································································································63
当前时间····································································································64
语言 ········································································································64
·································································································48
····································································································60
·································································································62
·······················································································63
4
目录
待机··········································································································64
记忆··········································································································65
自动负荷控制······························································································65
预洗水········································································································65
主洗水·······································································································65
漂洗水·······································································································65
低水压·······································································································65
标准附加温度······························································································66
预脱水地巾·································································································66
化学热消毒··································································································66
热消毒·······································································································66
卫生消毒····································································································67
超细纤维地巾 .······························································································67
整理标准····································································································67
整理消毒····································································································67
抹布整理·····································································································67
脱水 - 处理、标准、消毒··············································································68
脱水 - 处理、标准 +·····················································································68
脱水 - 处理地巾 / 抹布·················································································68
空容器传感器·····························································································68
更多程序····································································································69
棉质水平····································································································69
最低熨烫水平······························································································69
棉质预洗温度·····························································································69
预洗时间····································································································70
棉质时间····································································································70
最低熨烫时间·······························································································70
棉质地巾 / 抹布 / 免烫地巾 / 抹布预洗····························································70
特殊程序图表······························································································70
棉质地巾 / 抹布漂洗次数··············································································71
免烫地巾 / 抹布漂洗次数··············································································71
消毒漂洗次数·······························································································71
棉质地巾 / 抹布预漂洗··················································································71
免烫地巾 / 抹布预漂洗··················································································72
温度单位····································································································72
能耗控制····································································································72
5
警告和安全须知
本机器符合当前的安全要求。但不当使用会导致人身伤害和财产损失。
为避免意外风险和机器损坏，请在首次使用机器前仔细阅读本指南。 本指南包
含有关机器安全、使用和保养的重要信息。
请妥善保管本指南，并确保将其提供给新用户。必须让新用户知晓指南中的
警告和安全须知内容。
请将本指南交予机器的未来用户 / 所有人。
正确应用
只能使用本机器清洗：厂商在清洗和护理标签上规定为可机洗的地巾 / 抹布；可
►
手洗羊毛、羊毛混纺纺织品；及缎子、蕾丝、丝绸和其他可手洗地巾 / 抹布。任何
其他应用均可能是危险的。不正确和不当使用机器所致的损害生产商概不负责。
必须按照本指南所述使用机器，必须定期检查机器，以确保机器运行正常。必要
►
时必须进行保养。
本机器不适合户外使用。
►
6
警告和安全须知
身体、感官、智力能力较低和经验、知识缺乏人员，只有在有人监管情况下或已
►
有人示范过如何安全使用机器后，且知道和了解不正确操作的后果后，方可使用本
机器。
八岁和八岁以上儿童，只有在已有人示范过如何安全使用机器后，且知道和了解
►
不正确使用的后果后，方可在无人监管情况下使用本机器。
不得让儿童在无人监管情况下清洁、保养本机器。
►
儿童在机器附近时请注意监管，切勿让其玩耍机器。
►
确保通过进行合适的验证测试来维持热消毒及化学热消毒程序的标准（依据当地
►
管理法规），是操作人员的责任。消毒程序不得中断，否则会影响消毒效果。
7
警告和安全须知
技术安全
安装机器之前，请检查其外部是否存在明显的损伤。
►
若机器已损坏，切勿安装和使用。
只有正确接地后才能保证本机器的电气安全。必须对此基本要求进行测试，如果
►
存在任何疑虑，应由具有资质的电工对电气系统进行彻底检查。接地不充分导致的
后果（如触电）美诺（Miele）概不负责。
未经授权的修理会对用户构成不可预见的危险，美诺（Miele）对此不承担责任。
►
只有美诺（Miele）授权的维修技术员才可进行维修。不遵守此规定造成的损坏不在
保修范围内。保养、维修工作未结束前不得接通机器电源。
未经美诺（Miele）授权不得对机器进行任何改动。
►
机器发生故障时、安装时、保养时、维修时，必须切断机器电源。
►
8
警告和安全须知
只能使用全新的软管套件将本机器连接到实地供水处。不得重复使用旧软管。定
►
期检查软管是否有磨损。及时更换以规避泄漏风险和随后的损坏。
只能使用美诺（Miele）原厂正品配件替换故障部件。只有安装这样的配件才能
►
保证机器的安全标准。
切勿通过延长线、多孔插座转接器将机器连接到主电源。这样不能保证机器的安
►
全要求（如危险、过热）。
若在商用环境中使用本机器，请确保遵守所有相关健康和安全法规。
►
不得在非平稳处（如船上）使用本机器。
►
请遵循“安装和连接”和“技术数据”中的指示。
►
插座的安装位置必须易于接近，以方便洗衣机电源的切断。
►
对于硬接线机器 , 备的现场全极隔离器的安装位置必须易于接近，以方便洗衣机
►
电源的切断。
如果所在国家地区易受蟑螂或其他害虫侵袭，请特别注意始终保持机器及其周边
►
环境的清洁卫生。任何由于蟑螂或其他虫害对机器造成的损坏均不在保修范围内。
9
警告和安全须知
正确使用
本机器的最大清洗量为 6.5 公斤。各个程序的建议最大负荷参见“程序图表”。
►
请勿将您的机器安装在可能低于冰点的房间内。结冰的软管受到压力之后可能会
►
发生爆裂。如果周围的环境温度低于冰点，电子控制装置的可靠性可能受到影响。
首次使用机器之前，请检查机器后端的运输杆是否已经取下（见“安装和连接”
►
相应章节）。如果运输杆未取下，在脱水过程中，运输杆可能会对机器及周围家具
和电器造成损伤。
如果需要将机器闲置一段时间（例如节假日），请关闭水龙头，尤其当此机器周
►
围没有安装地面排水管（排水槽）时。
请确保各种异物（例如钉子、别针、硬币、纸夹等）不会随地巾 / 抹布进入洗衣机内。
►
清洗前必须将地巾 / 抹布上金属屑之类的污物抖掉。这些异物可能会损坏机器内部的
组件（例如泡沫容器、滚筒），同时也可能损坏待洗地巾 / 抹布。
10
警告和安全须知
如果添加的清洗剂剂量正确，则无需对机器进行除垢。但如果您确实希望对机
►
器进行除垢，仅需使用专用的非腐蚀性除垢剂，且要严格遵循包装上的说明。可从
MieleSparePartsepartment（美诺（Miele）配件部）和美诺经销商处订购专用除垢剂。
在机器中清洗前，在溶剂型清洁剂中预处理过的纺织品必须在清水中彻底漂洗干净。
►
切勿在本机器中使用溶剂型清洗剂（如包含挥发油的清洗剂），因为这样可能对
►
零部件造成损坏及产生有毒烟雾。使用此类清洗剂还可能引起火灾或爆炸。
不得将挥发油、汽油、石蜡及任何易燃液体存储于本机器附近或在附近使用。火
►
灾和爆炸危险！
只能使用生产商指定的适用于家用洗衣机的染料。请务必仔细阅读生产商提供的
►
说明书。
染色剂和燃料去除剂都含有硫化物，可能会引起腐蚀等不良后果。 切勿在机器中
►
使用此类产品。
11
警告和安全须知
液体清洁剂和消毒剂含氯和次氯酸钠，要避免其与不锈钢表面（前部、盖、外壳）
►
的接触。这些液剂对不锈钢有腐蚀作用。含氯漂白剂蒸汽也有腐蚀性。将这些溶剂
存储于本机器附近时，存储容器不得敞开。
切勿使用高压清洁器、软管清洁本机器。
►
当将清洁剂和特殊用途产品一起使用时，务必要遵循厂商的指示。 产品只能用于
►
厂商所批准的用途，以避免任何物资损失和强烈化学反应的发生。
配件
零配件只有在获得美诺（Miele）明确批准后方可安装。如果使用了其他部件，
►
则声明的保修、性能和产品责任将失效。
可使用合适的堆叠套件（作为可选配件提供）将美诺滚筒式烘干机堆叠于美诺洗
►
衣机之上。
若欲将本机器安装于美诺基座（作为可选配件提供）上，请确保订购的型号与机
►
器匹配。
因不遵守“警告和安全须知”所致的损坏，美诺（Miele）概不负责。
12
控制面板
医用地巾清洗消毒机操作
①启动按钮
启动所选程序。
② –、OK 和 + 按钮的显示屏
更多信息见下页。
③ 按钮
用于选择延迟启动。
④ PC/ 光纤接口
维修技术员通过该接口对您的机器进
行诊断检查，也可用于升级程序数据。
⑤带指示灯的预洗 / 预漂洗按钮
⑥程序选择旋钮
用于选择程序。 可顺时针和逆时针旋
转程序选择器。
⑦开关按钮
若启动、程序 / 防皱阶段结束 15 分钟
后未做任何选择，出于节能目的，机
器将自动关闭。
⑧机门按钮
打开机门。
13
医用地巾清洗消毒机操作
显示屏
- / + 按钮
用于更改显示屏中的高亮数值：
减小数值、上移高亮内容
-
增大数值、下移高亮内容。
+
OK 按钮
用于确认所选数值和选择下一数值。
以下内容通过显示屏选择：
– 多种程序
– 某些程序的温度
– 最终脱水转速
– 延迟启动
显示屏还显示程序的持续时间和当前时间。
设置 菜单也通过显示屏操作。
14
首次使用机器前，确保机器安装和
连接正确。安装和连接请检查确认
排水过滤器已牢固安装，以免在使
用机器的过程中出现漏水现象。
为安全起见，确保机器安装和连接正确。
必须在未放地巾 / 抹布情况下运行清洗
程序后方可启用脱水功能。
■
按下按键
启动机器。
若是首次启动机器，将出现欢迎屏幕：
Miele Professional Willkommen（ 欢 迎
使用美诺专业电器）
首次使用前
• 若安装人员未卸除运输杆，则请先卸
除后再按OK键。
之后将出现语言设置屏幕。
设置当前时间
■
使用 - 和 + 按钮设置小时数，按下
键确认设置。然后以相同方式设置分钟
数。 确认分钟设置后，屏幕中将出现
主菜单。
首次运行程序
OK
首个程序 完 成 后 将不再出现欢迎
屏幕。
之后将出现语言设置屏幕。
■
使用-和+按钮选择所需语言，按下
OK键确认选择。
卸除运输杆说明
为避免损坏，首次使用机器前必须
卸除运输杆。 有关卸除方法，请
参考“安装与连接”。
您的机器现可运行首个程序。
■
将程序选择钮旋转到 Cleaning cloths
40℃（抹布 40℃）位置。
■
打开水龙头。
■
按下 Start（启动）按钮。
程序结束时，机器准备就绪。
15
正确的操作方法
简要说明
标题编号 , , ……
显示工作顺序，可用作清洗程序的简短
说明。
将待洗地巾 / 抹布分类
异物（如钉子、硬币、回形针等）
会损坏地巾 / 抹布和机器内的部件。
请勿在本机器中使用溶剂型清洗剂。
准备好地巾、抹布等
■
将地巾、抹布和衬垫放入滚筒中之前
要将之用力整理，清除大粒污物。
将地巾 / 抹布分类
■
对于极脏的区域、污渍等，应尽早进
行清洗。应使用不褪色的软布将喷溅
到地巾 / 抹布上的液体轻轻擦去。切勿
用力揉搓！
■
按照颜色和护理标签对地巾 / 抹布进行
分类。 大多数地巾 / 抹布在领口或边
缝处均贴有地巾 / 抹布护 理标签。
深色纺织品一般都含有大量染色剂，应
对它们进行数次独立清洗，之后才能和
其它地巾 / 抹布混 合清洗。 白色地巾 /
抹布和有色地巾 / 抹布须分开清洗。
16
切勿在本机器内清洗厂商在护理标签上
规定为
不可洗
的地巾 / 抹布。 （ 标
志）
正确的操作方法
放入滚筒
■
按下按键
■
按下 Door（机门）按钮，打开滚筒门。
■
将地巾、抹布和衬垫散置于滚筒内。
■
将地 巾 / 抹布展 开后散置于滚筒内。
大件和小件地巾 / 抹布混洗清洗效果较
好，同时可使脱水过程地巾 / 抹布量分
布更均衡。
滚筒加满地巾 / 抹布，可最大限度地提
高用 水、用电效率。但切 勿使地巾 / 抹
布量超标，否则会引起地巾 / 抹布褶皱，
并降低清洗效率。
• 轻轻关闭机门。
确保无地巾 / 抹布夹在滚筒门和密封
之间。
17
正确的操作方法
选择程序
■
将选择钮旋转到您需要的清洗程序。
所选程序将出现在屏幕中。
ખ࣊
屏幕将转而显示所选程序的菜单。
将程序选择钮旋转到 Further programmes
（更多程序）时，将在屏幕中出现一系
列程序。
ளڠࣇὈ
ܪူڠࣇ
ખ࣊ஞူ
■
使用-和+按钮，选择需要的程序，
所选程序指示灯 闪 亮， 按 下
OK
按钮
确认选择。
屏幕将转而显示所选程序的菜单。
ቓࣕ
ቓࣕ
■
之后您可使用-和+按钮来更改脱水
转速（指示灯闪亮）。 按下OK按钮
确认。对于某些 程 序， 可 使用+和
按钮来更改温度。
-
■
之后您可使用-和+按钮来更改脱水
转速（指示灯闪亮）。 按下OK按钮
确认选择。
18
预洗 / 预漂洗
■
若所洗地巾 / 抹布特别脏，可选择额
外预洗和预漂 洗。若屏幕中未出现这
些额外选项，即 表明所选程序不具备
这些选项。
延迟启动
■
必要时可选择延迟启动
（见“延迟启动”）。
添加清洗剂
应根据脏污程序和水硬度来调整清洗剂
用量。
用量过少会导致：
– 无法正确清洗地巾 / 抹布，长此以往
将使地巾 / 抹布颜色变暗，质地变硬。
– 粘结在地巾 / 抹布上的油脂颗粒无法
清除。
– 水垢沉积到加热元件上。
用量过多会导致：
– 泡沫过多，从而影响地巾 / 抹布在滚
筒内的搅动效果，并导致清洗、漂洗
和脱水等操作的效果不佳。
– 不环保。
更多信息见“清洗剂”。
正确的操作方法
■
拉出清洗剂分配盒，并将清洗剂按下
列要求放入各容器中：
= 预洗所需的清洗剂（按推荐总量的
1/4 ）。
= 用于主洗过程的清洗剂
= 地巾 / 抹布柔顺剂或液态粉浆
■
关闭清洗剂分配盒。
消毒程序期间不使用试剂盒 。切勿
将任何物品放入其中。
本机器可连接用于分配液剂的外部分
配系统（见“清洗剂 -外部分配系统”）。
19
正确的操作方法
启动程序
程序可启动时 Start（启动）按钮将随即
闪烁。
■
按下 Start（启动）按钮。
Start（启动）按钮将闪亮。
若未选择延迟启动，程序预计持续时间
将出现在屏幕中。 时间按分钟倒计时。
在程序开始后的前 10 分钟，机器将测量
得到地巾 / 抹布的吸水量。 根据吸水率
的大小，程序持续时间可能延长或缩短。
显示屏还将显示程序序列。当完成某部
分清洗程序时，机器将给出相应显示。
从滚筒取出地巾 / 抹布
在程序的最后阶段，滚筒将继续间歇性
旋转最多 30 分钟，以保持筒内所有负载
的残留水分均匀，并帮助防皱（防皱阶
段）。 在防皱阶段，可随时打开滚筒门
取出地巾 / 抹布。
防皱阶段结束后 15 分钟机器将自动
关闭。 您需要按下按钮 重新启动
机器。
确认将所有地巾 / 抹 布从滚筒中取
出。 留在滚筒中的地巾 / 抹布可能
在下次清洗中将其他地巾 / 抹布染色
或被其他地巾 / 抹布染色。
■
检查机门缝的折叠处是否留有小件物
品，例如纽扣等。
■
将程序选择钮旋转到 Finish（整理）。
■
关闭滚筒门。 否则可能会由于疏忽大
意而导致异物 落入滚筒内。如果异物
留在滚筒内，可 能会在下一次清洗过
程中损坏地巾 / 抹布。
■
按下按键关闭机器。
■
按下 Door（机门）按钮，打开滚筒门。
■
取出地巾 / 抹布。
20
脱水
最终脱水的最大转速
程序 rmp
Standard（标准） 60℃ 1400
Standard plus（标准 +） 1400
Thermal disinfection（热力消毒） 1400
Chemo thermal dis.（化学热消毒） 1400
Cleaning cloths Hygiene（抹布卫生） 1400
Cleaning cloths（抹布） 1400
Pads（衬垫） 40℃ 1400
New mops（新地巾） 1400
Mops（地巾） + treat（处理） 不显
Treat mops（处理地巾） 不显
Finish cleaning cloths（抹布整理理 ） 不显
Curtains（窗帘） 600
Cottons universal（一般棉质） 1400
Cottons hygiene（棉质卫生） 1400
Intensive（加强） 1400
Intensive（加强） + 1400
Minimum iron（免烫地巾 / 抹布） 1000
Quick wash（快速清洗） 1400
Separate rinse（单独漂洗） 1400
Drain / Spin（排水 / 脱水） 1400
* 脱水转速取决于 Spin-treat（脱水 - 处理）、std（标
准）、disin.（消毒）及Spin & Finish clean cloths（脱
水 & 整理抹布）设置。
您可以降低最终脱水的转速，但不可选
择高于上述图表数值的最终脱水转速。
省略最终脱水（暂停漂洗）
■
选择 Rinse hold（暂停漂洗）设置。
机器将 不 会 对地巾 / 抹布进行 最 终脱
水，而地巾 / 抹布将一直漂浮于最后一
次的漂洗水中。
— 启动最终脱水：
洗衣机将显示最大脱水转速值。 您可
选择低于此转速的脱水转速值。按下
Start（启动）按钮开始最终脱水。
— 结束程序：
按下 Door（机门）按钮。 滚筒内的
水将排出。 再次按下 Door（机门）
按钮打开机门。
省略漂洗和最终脱水之间的脱水
■
选择 Without spin（不脱水）设置。
最后一次漂洗完成后，滚筒内的水被
排出。在程序最后，滚筒继续间歇性
旋转最多 30 分钟，以保持筒内所有负
载残留水分均匀，并帮助防皱（“衬垫”
和“新地巾”程序除外）。
漂洗和中间脱水
主洗过程结束后，以及在两次漂洗过程
之间，都将进行一次脱水处理。 如果降
低最终脱水的转速值，则也将同时降低
中间脱水的转速值。
Thermal disinfection（热力消毒）、
Chemo thermal disinfection（ 化 学
热消毒）及 Cleaning cloths hygiene
disinfection（ 抹 布 卫 生 消 毒 ） 程
序 中 无 Rinse hold（ 暂 停 漂 洗） 和
Without spin（不脱水）选项。
21
延迟启动
延迟启动可使您选择何时启动程序。 程
序启动可延迟 30 分钟至 24 个小时，这
可使您充分利用夜间电费优惠费率。
设定当前时间后延迟启动才能正常工作。
若 您 在 Settings（ 设 置）/Supervisor
level（管理级）/Time of day（当前时
间）下选定“No time displayed”（不
显示时间）选项，则程序开始时间可延
迟长达 96 小时。
选择延迟启动
■
选择所需程序，然后按下 按钮。
ըҮ
ஞူ
若所选时间过长，请使用 – 按钮缩短时
间。
■
按下OK按钮确定结束时间。
开始延迟启动
■
按下 Start（启动）按钮。
ըҮௐ
屏幕将显示程序在多少小时和分钟后启动。
更改延迟启动
■
按下 按钮。
■
使用+ 和- 按钮修改程序结束时间。
■
按下OK按钮确认。
屏幕显示当前时间和程序预计结束时间。
■
使用+按钮选择让程序结束的时间。
第一次按下按钮后将把结束时间调至下
个整小时或半小时。随后每按一次按钮，
延迟时间将增加 30 分钟。
22
取消延迟启动
■
按下 按钮。
■
使用-按钮回调程序结束时间，直到
程序启动时间与当前时间相同为止。
■
按下OK按钮确认。
程序将立即启动。
机器在程序启动后方能准确确定实
际负荷量。 因 此， 程序结束时间可
能比起初显示的时间稍早。
程序图表
地巾
Starndard ( 标准 ) 60℃ 最多 6.5 公斤
地巾 / 抹布类 棉质、混合纤维和超细纤维地巾
注意 — 可使用整理剂。*
额外选项 额外预漂洗
清洗剂 特殊配方清洗剂
Starndard plus ( 标准 ) +60℃ 最多 6.5 公斤
地巾 / 抹布类 棉质、混合纤维和超细纤维地巾
注意
额外选项 额外预漂洗
清洗剂 特殊配方清洗剂
Thermal disinfection ( 热力消毒 ) 85℃ /15 分钟 最多 6.5 公斤
地巾 / 抹布类 棉质、混合纤维和超细纤维地巾
注意
额外选项 额外预漂洗
清洗剂 特殊配方清洗剂
Chemo thermal disinfection ( 化学热消毒 ) 70℃ /10 分钟 最多 6.5 公斤
地巾 / 抹布类 棉质、混合纤维和超细纤维地巾
注意
额外选项 额外预漂洗
清洗剂 特殊配方清洗剂（必须遵循所在国规定的消毒参数）
— 可使用整理剂。*
— 可修改温度。*
— 可选择更多消毒过程。*
— 可使用整理剂。*
— 可选择更多消毒过程。*
— 可使用整理剂。*
* 可通过设置 / 管理级菜单选择这些设置。
23
Loading...