Miele PW 413, PW 418 Installation diagram

Installation plan Commercial Washing Machine PW 413 PW 418

It is essential to read these operating instructions before installing and using the appliance. This prevents both personal injury and damage to the appliance.

en-AU,NZ

M.-Nr. 10 682 620

Contents

Installation and planning notes..........................................................................................4

Installation requirements ....................................................................................................... 4

Storage/Transport.................................................................................................................. 4

General operating conditions ................................................................................................ 4

Installation ............................................................................................................................. 5

Installation on concrete plinth .......................................................................................... 5

Levelling the machine............................................................................................................ 6

Securing the machine............................................................................................................ 6

Machine connections ............................................................................................................ 7

Models with detergent dispenser drawer (WEK) ............................................................. 7

Models without detergent dispenser drawer (WEK)......................................................... 8

Electrical connection ............................................................................................................. 9

Water connection ................................................................................................................ 11

Cold water connection ................................................................................................... 11

Hot water connection..................................................................................................... 12

Drain valve...................................................................................................................... 13

Dispenser pump connections ............................................................................................. 14

Optional accessories........................................................................................................... 16

Payment system............................................................................................................. 16

Peak load cut-out........................................................................................................... 16

XKM RS232 communication module ............................................................................. 16

Plinth .............................................................................................................................. 17

Vapour and foam venting kit (BWS) ............................................................................... 17

Technical drawings............................................................................................................18

PW 413................................................................................................................................ 18

Dimensions..................................................................................................................... 18

PW413 with Mieleplinth (UG/UO) ................................................................................. 19

Installation ...................................................................................................................... 20

PW 418................................................................................................................................ 21

Dimensions..................................................................................................................... 21

PW418 with Mieleplinth (UG/UO) ................................................................................. 22

Installation ...................................................................................................................... 23

Anchoring PW413/418 ....................................................................................................... 24

Fixing to floor/concrete plinth ........................................................................................ 24

Fixing to the floor/concrete plinth when installing in a run............................................. 24

Fixing to the floor with Miele plinth ................................................................................ 25

Technical data....................................................................................................................26

Water connection ................................................................................................................ 26

Models with detergent dispenser drawer (WEK)............................................................ 26

Models without detergent dispenser drawer (WEK)....................................................... 26

Drain valve...................................................................................................................... 26

Connection for equipotential bonding................................................................................. 26

Anchoring ............................................................................................................................ 27

Fixing to the floor............................................................................................................ 27

Fixing to the floor with Miele plinth ................................................................................ 27

Fixing to a concrete plinth (provided on-site)................................................................. 27

Contents

PW 413................................................................................................................................ 28

Voltage versions and electrical data............................................................................... 28

Installation dimensions................................................................................................... 28

Transport data, weight and floor load ............................................................................ 28

Emissions data ............................................................................................................... 29

PW 418................................................................................................................................ 30

Voltage versions and electrical data............................................................................... 30

Installation dimensions................................................................................................... 30

Transport data, weight and floor load ............................................................................ 30

Emissions data ............................................................................................................... 31

Installation and planning notes

Installation requirements

The washing machine must be installed and commissioned by a Miele Service technician or by an authorised service technician.

 The washing machine must be installed in accordance with

applicable regulations and standards. Local energy and water supplier regulations must also be observed.

 This washing machine must only be operated in a room that has

sufficient ventilation and which is frost-free.

This machine should not be installed or operated in any area where there is a risk of explosion.

Storage/Transport

The following conditions must be observed for transport and storage:

– Ambient temperature: 0-40 °C

– Humidity: non-condensing

General operating conditions

This washing machine is intended only for use in a commercial environment and must only be operated indoors.

– Ambient temperature of installation location: 0-40 °C

– Relative humidity: non-condensing

– Maximum height above sea level of installation site: 2000 m

Depending on the nature of the installation site, sound emissions and vibration may occur.

Useful tip: Have the installation site inspected and seek the advice of a professional in instances where increased noise may cause a nuisance.

4 PW 413 / PW 418

Installation and planning notes

Installation

Transport the washing machine to its installation site using a suitable pallet truck and remove the transport packaging.

The washing machine must be set up on a level and firm surface with the minimum stated load bearing capacity (see "Technical data").

The floor load created by the washing machine is concentrated and transferred to the installation footprint via the machine feet.

Useful tip: A concrete floor is the most suitable installation surface, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface.

The washing machine requires a gap of at least 50mm at each side to allow for movement during operation. To ensure suitable access for further maintenance and service work, please ensure a minimum distance of 400mm is maintained between the back of the machine and the wall.

Installation on concrete plinth

The washing machine can be installed on a concrete plinth if desired.

The concrete materials and the durability of the concrete plinth must be assessed in accordance with the floor load bearing capacity given in "Technical data".

 To guarantee the stability of the washing machine, make sure that

the concrete plinth is sufficiently stable on the floor and that it is capable of withstanding any burden or force from the washing machine.

 The washing machine must be secured to the concrete plinth using

the fixtures and fastenings supplied.

 The washing machine must be secured to the plinth immediately after installation!

There is a risk of the washing machine falling off a raised plinth during a spin cycle if it is not secured.

PW 413 / PW 418 5

Installation and planning notes

Levelling the machine

 Align the washing machine vertically and horizontally using the

adjustable feet and a spirit level.

The washing machine must stand evenly and horizontally on all four feet to ensure trouble-free and energy-efficient operation. Otherwise the water and energy consumption increases and the washing machine might move around.

 After aligning the machine, tighten the counter nuts by turning them

in an anti-clockwise direction with a spanner. This will prevent the feet from adjusting themselves.

Securing the machine

 The feet of the washing machine must be secured to the concrete

plinth using the fixtures and fastenings supplied.

The material provided is intended for use in bolting the machine to a concrete floor. For other types of flooring, please purchase suitable fitting materials separately.

6 PW 413 / PW 418

Models with

⑥

①

②

③

④

⑤

⑦

⑧ ⑨

⑩

⑪

detergent dispenser drawer (WEK)

Installation and planning notes

Machine connections

Detergent dispenser drawer (WEK)

Communication module slot

The XKMRS232 communication module is available as an optional accessory.

Electrical connection

2x hard water connection

(Optional)

Cold water connection

Hot water connection

Water temperature to maximum 70°C.

Cold water connection

Cold water connection for liquid dispensing

(Optional)

Connections for external dispenser pumps

For up to 12 dispenser pumps.

Vapour extraction / free outlet TypeAB

Drain valve

Connection for plastic pipe HTDN70.

PW 413 / PW 418 7

Installation and planning notes

⑥

①

② ③

④

⑤

⑦ ⑧

⑨

Models without detergent dispenser drawer (WEK)

Communication module slot

The XKMRS232 communication module is available as an optional accessory.

Electrical connection

2x hard water connection

(Optional)

Cold water connection

Hot water connection

Water temperature to maximum 70°C.

Cold water connection for liquid dispensing

Connections for external dispenser pumps

For up to 12 dispenser pumps.

Vapour extraction/free outlet TypeAB

Drain valve

Connection for plastic pipe HTDN70.

8 PW 413 / PW 418

Installation and planning notes

Electrical connection

The electrical connection must be carried out by a qualified electrician who must ensure that all electrical work is carried out in accordance with applicable electrical regulations and standards.

 This washing machine must be connected to an electrical mains

supply that complies with local and national regulations. Please also observe your insurance and energy supplier's regulations as well as any workplace health and safety regulations.

 The required voltage, rated load and fusing rating can be found on

the data plate on the washing machine. Before connecting the machine to the electricity supply, please ensure that the mains supply voltage complies with the values given on the data plate.

Connection to a supply voltage other than the one quoted on the data plate can lead to functional faults and damage to the washing machine. If more than one voltage is quoted on the data plate, the washing machine can be converted for connection to the voltages stated.

 Conversion to a different voltage must only be carried out by a

Miele Professional Service technician or by an authorised service technician. The wiring instructions given on the wiring diagram must be followed.

The machine can either be hard-wired or connected using a plugand-socket. For a hard-wired connection, an all-pole isolation device must be installed on site.

For hard-wired machines, connection should be made via a suitable mains switch with all-pole isolation which, when in the off position, ensures a 3mm gap between all open contacts. These include circuit breakers, fuses and relays.

If the mains supply cannot be permanently disconnected, the isolator switch (including plug and socket) must be safeguarded against being switched on either unintentionally or without authorisation.

Useful tip: We recommend connection to the power supply via a suitable plug and socket which must be easily accessible for servicing and maintenance work after the machine has been installed. An electrical safety test must be carried out after installation and after any service work.

PW 413 / PW 418 9

Installation and planning notes

 If it is necessary to install a residual current device (RCD) in

accordance with local regulations, a residual current device typeB (sensitive to universal current) must be used.

An existing typeA residual current device (RCD) must be exchanged for a typeB RCD.

 If necessary, equipotential bonding with a good contact

connection must be guaranteed in compliance with all applicable local and national installation specifications.

Equipotential bonding must have an earth current rating >10mA. Accessories for equipotential bonding are not supplied and need to be ordered separately.

10 PW 413 / PW 418

+ 22 hidden pages