When using electrical appliances basic safety precautions should always be
followed, including the following:
Read all instructions before installation or use of the coffee system.
Proper Use
Please read these instructions
carefully to prevent accidents and
machine damage.
This appliance complies with current
safety requirements. Improper use
of the appliance can cause personal
injury and material damage.
This coffee system is not designed
~
for commercial use. It is intended for
household use and only, for the
preparation of coffee, cappuccino,
espresso, etc.
Do not use appliance other than for its
intended use. Any other use could be
dangerous.
Read this safety information carefully
before operating the appliance.
They contain important information
on the safe installation, operation,
and care of your coffee system. To
avoid the risk of personal injury or
damage to the coffee system, it is
important that you carefully read the
instructions.
Keep these instructions in a safe
place and pass the on to any future
user.
This coffee machine is not intended
~
for outdoor use.
The coffee machine is intended for
~
household use only for the preparation
of coffee, cappuccino, espresso, latte
macchiato, etc.
Any other use is not supported. Miele
cannot be held liable for damage
resulting from incorrect or improper
use.
Persons which lack physical,
~
sensory or mental abilities or
experience with the machine should not
use it without supervision or instruction
by a responsible person.
4
IMPORTANT SAFETY INSTRUCTIONS
Children
Caution! The coffee and hot water
dispensers present a danger of
burning or scalding!
Children's skin is very sensitive and
reacts to hot temperatures.
Keep the coffee system out of reach
~
of children.
Close supervision is necessary
~
when the coffee machine is used near
children.
Never let children play with the
~
coffee machine.
Technical safety
Before installing the coffee machine,
~
check for externally visible damage. If
the coffee system is damaged, it may
pose a safety hazard and must not be
used under any circumstances.
Before connecting the coffee
~
machine, check the voltage and
frequency indicated on the data plate
against the voltage and frequency of
the household electrical supply.
The values must correspond in order to
prevent damage to the coffee machine.
If in doubt, consult a qualified
electrician. To disconnect, turn the
main switch at the back of the machine
to 0, then remove the plug from the wall
outlet.
Be certain your appliance is
~
properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.
Do not operate any appliance with a
~
damaged cord or plug, or after the
appliance malfunctions or has been
damaged in any manner. Contact
Miele.
Unplug the machine from the power
~
supply immediately if you notice any
damage or smell scorching, for
example.
Ensure that the power cord will not
~
be pinched or damaged by any sharp
edges.
Ensure that the power cord does not
~
hang down. Someone could trip over it
and the machine could be damaged.
The coffee machine must not be
~
used in mobile installations such as
ships.
The ambient temperature should be
~
between 50°F (10°C) and 90°F (32°C).
Ensure that there is sufficient
~
ventilation around the coffee machine.
Do not cover the vents on the top.
5
IMPORTANT SAFETY INSTRUCTIONS
Do not place the appliance on or
~
near a hot gas or electric burner, or in a
heated oven.
The use of accessory attachments
~
not recommended by the appliance
manufacturer may result in fire, electric
shock or injury to persons.
Protect the coffee machine from
~
water and water spray.
Installation, maintenance and
~
repairs may only be carried out by
qualified technicians.
Repairs must only be performed by
~
a trained technician in accordance with
national and local safety regulations.
Repairs and other work by
unauthorized persons could be
dangerous and may void the warranty.
Defective components should be
~
replaced by Miele original parts only.
Only with original Miele parts can the
manufacturer guarantee the safety of
the appliance.
Unplug from outlet when not in use
~
and before cleaning and care. Allow to
cool before putting on or taking off
parts, and before cleaning the
appliance.
Never open the outer casing of the
~
appliance. Tampering with electrical
connections or components and
mechanical parts is dangerous and
may cause machine damage.
To protect against fire, electric
~
shock and injury to persons do not
submerge the cord, plugs or coffee
machine in water or other liquids.
If the coffee system will not be used
~
for an extended period of time, turn it
off by using the main power switch.
Safety
Caution! The coffee and hot water
dispensers present a danger of
burning or scalding! The liquids and
steam dispensed are very hot.
Keep away from the areas under the
~
coffee dispensers when beverages or
steam are being dispensed.
Do not touch hot components. Use
~
handles or knobs.
The spouts can spray hot liquid or
~
steam. Be sure the cappuccinatore is
fitted correctly and only use it if it is
clean.
Do not use the coffee machine to
~
clean objects.
Clean the coffee machine and the
~
milk flask (depending on model)
thoroughly before using for the first
time. Before first use, flush the coffee
and milk supply lines thoroughly (see
"Cleaning and care").
Only fill the water container with
~
cold, fresh tap water. Warm or hot
water and other liquids can damage the
coffee machine.
Change the water every day to
~
prevent a build-up of bacteria.
Do not use mineral water. Mineral
~
water will cause serious limescale
deposits to build up in your coffee
machine and damage it.
6
IMPORTANT SAFETY INSTRUCTIONS
Fill the bean container only with
~
roasted whole coffee beans. Do not fill
the bean container with coffee beans
which have been treated or with ground
coffee.
Do not reach into the grinder.
~
Only put ground coffee or cleaning
~
tablets to the ground coffee chute. The
cleaning tablets remove grease from
the brew unit of the coffee machine.
Only use plain milk. Flavored milk
~
products contain substances that can
clog the milk system.
Do not use coffee beans which have
~
been treated with caramel, sugar, or fill
the coffee machine with other
sugar-containing liquids. Sugar
damages the machine!
Never place a cup with a burning
~
alcohol-coffee mixture underneath the
main dispenser. This could cause
plastic parts of the coffee machine to
catch fire and melt.
Do not place any open flame, e.g. a
~
candle, on or near the coffee machine.
The coffee machine could catch fire
and the fire could spread.
Disconnect the coffee machine from
~
the power supply before cleaning.
Descale the coffee machine
~
regularly with the appropriate number
of Miele descaling tablets for the water
hardness level in your area. Descale
the machine more frequently in areas
with very hard water. The manufacturer
cannot be held liable for damage
arising from insufficient descaling.
Degrease the brew unit regularly
~
with the supplied Miele cleaning
tablets. Depending on the natural oil
content of the coffee used, the brew
unit can become blocked quite quickly.
Used coffee grounds from the waste
~
container should be disposed of with
organic waste or put on the compost
heap Coffee grounds can clog the sink.
For machines with stainless steel
trim:
Do not use sticky notes, transparent
~
adhesive tape, masking tape or other
types of adhesive on the surface of the
trim. These damage the surface,
causing it to lose its dirt repellent
protective coating.
The surface of the stainless steel
~
trim is susceptible to scratching. Even
magnets can cause scratches to
appear.
Clean the coffee machine and the
~
milk flask (depending on model) daily
(for further information see "Cleaning
and Care").
Do not use a steam cleaner to clean
~
this machine. The steam could cause a
short circuit.
SAVE THESE INSTRUCTIONS
AND REVIEW THEM
PERIODICALLY
7
Guide to the machine
a Cup warming surface
b Bean container, ground coffee chute
and rotary selector to control the
fineness of the ground coffee
c Display and controls
d Hot water spout
e Central spout with integrated
cappuccinatore
f Waste container
g Drip tray
8
h Drip tray cover
i Milk tube aperture
j Main switch
k Compartment for quick guide
l Water container
m Milk container
(depending on model)
Display and controls
Guide to the machine
Drink buttons
Press these buttons to prepare the
desired drink.
The symbols mean:
.Espresso b
/Coffee a
kLatte Macchiato g
HCappuccino f
To prepare a drink, press the
corresponding button once.
For two portions of a drink, press the
corresponding button briefly twice in
succession.
To specify portion size (programming
amount), hold the drink button down for
more than 3 seconds.
OK button e
With the OK button you confirm display
information and save settings.
Rotary selector d
You can select from the different
menu options using the rotary selector.
On/Off button - c
The On/Off button - turns the coffee
machine on and off (Standby), if the
main switch on the back is turned on.
Display h
The display gives information about
current action or status of the coffee
machine.
9
Guide to the machine
Button illumination
When the drink buttons are illuminated,
you are in the main menu and can
prepare drinks. If drink preparation has
commenced, only the corresponding
drink button is illuminated.
The semicircle also lights up on the
OK button shortly before the steam is
produced, e.g. for milk froth.
The OK button and the semicircle are
illuminated when a menu is called up,
when an option selection is possible or
if an action requires confirmation.
Operation
You are in the main menu when the
display shows:
SELECT TYPE OF DRINK
rs
If r and s appear in the display, you
can select further options using the
rotary selector.
To select an action or setting
^
Turn the rotary selector until the
action or setting you want appears in
the display.
Press the OK button.
Calling up a menu
You can call up menus by holding
^
the OK button for more than
2 seconds
Using the rotary selector, you choose
from
OTHER DRINKS
–
MAINTENANCE
–
SETTINGS
–
Press the OK button to confirm your
^
selection.
You will be able to start actions or alter
settings in the selected menu.
Exiting a menu level
^ Turn the rotary selector until BACK
appears in the display.
Press the OK button.
or
^
Press the OK button for 2 seconds .
or
If none of the buttons has been pressed
for a while, the coffee machine will
revert to the main menu.
You will be able to identify the current
active setting by the check B.
^
To save a setting, press the
OK button.
10
Preparing the coffee machine for use
Please read the operating
instructions and take the time to
familiarize yourself with the coffee
machine before using it for the first
time.
Before using for the first time
Set up the coffee machine and
^
remove any protective film (see
"Installation").
Clean the coffee machine thoroughly
(see "Cleaning and Care") before
filling it with water and coffee beans.
^ Insert the plug of the coffee machine
into the outlet (see "Electrical
connection").
Turning on for the first time
When you turn the coffee machine on
for the first time, you will be prompted
to set the following after the welcome
screen has appeared:
Language
–
Time format
–
Time of day
–
Press the On/Off button -.
^
The welcome message MIELE WILLKOMMEN will appear in the
display briefly.
To set the language
^ Turn the rotary selector until the
language you require appears in the
display.
Press the OK button.
The setting is now saved.
^
Set the main switch at the back of the
coffee machine to "l".
To set the time format
^
Select 12 H, if you want the time to
be shown as a 12 hour clock.
or
^
Select 24 H, if you want the time to
be shown as a 24 hour clock.
^
Press the OK button.
The setting is now saved.
11
Preparing the coffee machine for use
To set the time of day
Turn the rotary selector until the
^
current hour appears in the display.
Press the OK button.
Turn the rotary selector until the
^
current minutes appear in the
display.
Press the OK button.
The setting is now saved.
SET UP SUCCESSFUL will now appear
in the display.
Press the OK button.
^
In the display you will see:
FILL WATER CONTAINER
AND PLACE IN MACHINE
^ Fill the water container with cold,
fresh tap water.
TIP Place a suitable container
underneath the hot water spout.
In the display you will see:
SYSTEM FILLING UP
rSTART
^
Press the OK button.
TIP Continue following the instructions
given in this booklet to set up your
machine and familiarize yourself with it.
Water hardness
Water hardness is an indication of the
amount of minerals dissolved in water.
The higher the mineral content, the
harder the water. And the harder the
water, the more often the coffee
machine will need to be descaled.
The coffee machine monitors the
quantity of water and steam used. The
number of drinks which can be
dispensed before the machine needs to
be descaled will depend on the water
hardness level set.
Set the water hardness level on the
coffee machine to the water hardness
level for the local area to ensure that
the machine functions correctly and is
not damaged. This will ensure that the
reminder to descale the machine will
appear in the display at the correct
time.
There is a choice of four water
hardness levels:
–
s
Level 1 (soft):
0 - 3 gr/gal (0 - 3 °dH)
–
Level 2 (moderate):
4 - 7 gr/gal (4 - 7 °dH)
–
Level 3 (hard):
7 - 15 gr/gal (7 - 14 °dH)
12
–
Level 4 (very hard):
15 - 22 gr/gal (14 - 21 °dH)
Preparing the coffee machine for use
Determining the water hardness
You can test the water hardness with
the supplied test strips. Your local
water supplier will also be able to
advise you on the water hardness in
your area.
^ Dip the test strip in water for a
second, then shake off any excess
water. The result will be visible after
about one minute.
You can now set the water hardness
level for the coffee machine.
Setting the water hardness level
SELECT TYPE OF DRINK will appear in
the display.
Press the OK button until MENU
^
appears in the display.
Turn the rotary selector until
^
SETTINGS appears in the display.
Press the OK button.
SETTINGS
rWATER HARDNESSs
Select WATER HARDNESS and press
^
the OK button.
^ Turn the rotary selector until the water
hardness level you require appears
in the display.
Press the OK button.
The setting is now saved.
13
Filling the water tank
The quality of the water used plays an
important part in the overall quality of
the coffee.
The water tank should be emptied
and filled with fresh, cold tap water.
Hot or warm water, or other liquids
could damage the coffee system.
Do not use mineral water. Mineral
water will cause lime scale deposits
to build up in the machine, possibly
damaging it.
^ Open the lid on the left hand side of
the coffee system a. Pull the water
tank up and out using the handle b.
Fill the water tank with fresh, cold tap
^
water to the "Max." mark.
Be sure the area under the water
tank is clean and free of
obstructions. If the water tank is not
seated correctly the drainage valve
will not be sealed. Clean if
necessary.
14
^ Replace the water tank. Make sure
the tank fits correctly onto the notch
at the top of the housing.
^
Close the lid.
Fill the coffee bean container with
roasted espresso or coffee beans.
Important: Only use roasted
espresso or coffee beans in the
container.
Anything else, including ground
coffee, will damage the grinder.
Filling the coffee bean container
Important: Do not use coffee beans
that have been treated with sugar,
caramel or other substances. Do not
put drinks containing sugar in the
coffee bean container. Sugar will
damage the machine.
Open the lid on the right of the coffee
^
system a. Remove the coffee bean
container lid b.
Fill the container c with roasted
^
coffee beans.
^ Replace the bean container lid, close
the coffee system lid.
TIP Only add enough beans to last for a
few days. Contact with the air causes
the beans to loose their flavor.
15
Turning the machine On / Off
The On/Off button - (Standby) can be
used to turn the coffee system on or off,
if the main switch at the back of the
machine is turned on.
Turning on
When the machine is turned on, it heats
up and rinses out the pipework. This
cleans and heats the pipework ready
for coffee preparation. After rinsing, hot
water will run into the drip tray.
TIP If you do not want the water from
the rinsing process to flow into the drip
tray, place a suitable container
underneath the coffee dispensers
before preparing the first coffee of the
day.
If the coffee machine still has an
operating temperature higher than
140°F (60°C), rinsing will not take
place.
^ Press the On/Off button -.
The following will appear in the display:
HEATING UP PHASE
Turning off
Press the On/Off button -.
^
The coffee machine rinses the coffee
pipework before turning off.
If you have made a drink with milk, the
following message appears in the
display:
RINSE THE
MILK SYSTEM
Press the OK button to rinse the milk
^
system.
Follow the instructions given in the
^
display.
The milk system is rinsed out.
If the milk system is not rinsed
before turning off, the message
RINSE THE MILK SYSTEM or CLEAN
THE MILK SYSTEM will appear in the
display next time the machine is
turned on.
Follow the instructions in the display
next time the machine is turned on
(see "Rinsing the milk system").
The following appears in the display
after heating up:
RINSING
Hot water will flow from the coffee
dispensers.
The main menu will then appear in the
display:
SELECT TYPE OF DRINK
You can now prepare drinks.
16
TIP To save energy, use the main
switch at the back of the coffee
machine to turn it off if it is not going to
be used for a long period of time,
e.g. during holidays.
Please note that the time of day will not
be saved and must be entered again
the next time the coffee machine is
turned on.
Pre-heating cups
Cups should always be pre-heated to
allow the flavor of espresso and other
coffee drinks to develop and be
retained.
The smaller the volume of
coffee/espresso and the thicker the
cup, the more important it is to pre-heat
the cup.
You can use the cup heating surface on
the top of the coffee machine to
pre-heat coffee cups and glasses. The
cup heating function must be turned
on.
To switch cup heating on or off
SELECT TYPE OF DRINK will appear in
the display.
Press the OK button until MENU
^
appears in the display.
Turn the rotary selector until
^
SETTINGS appears in the display.
Press the OK button.
SETTINGS
rCUP HEATINGs
Select CUP HEATING and press the
^
OK button.
^ To turn cup heating on, turn the
rotary selector until YES appears in
the display.
or
^ To turn cup heating off, turn the
rotary control until NO appears in the
display.
^ Press the OK button.
^
Arrange the cups or glasses on the
cup heating surface on the top of the
coffee machine.
The cup heating surface will be heated
continually until the coffee machine is
turned off.
17
Adjusting the coffee dispensers to the cup height
The coffee dispensers can be raised or
lowered to the height of your cup. If the
dispensers are closer the beverage will
not cool down as quickly and the crema
will have a better consistency.
^ Pull the coffee dispenser down to the
same level as the rim of the cup.
or
^ Push the dispenser up until there is
enough room to fit a larger cup or
mug underneath.
18
Preparation can be canceled while
STOP is showing in the display.
To cancel the preparation of coffee or
espresso,
press the OK button.
^
Drink preparation will be canceled.
To cancel the preparation of specialty
coffees with milk or two portions of a
drink, you can cancel
the preparation of the ingredients
–
individually or
the preparation of the entire drink.
–
To cancel an individual stage, e.g. milk
froth,
^ press the OK button once.
To cancel preparation of a whole drink,
^ press the OK button twice.
Canceling preparation
or
^ press and hold the OK button.
Drink preparation will be canceled.
TIP During the grinding and heating up
phases, preparation of the whole drink
can be canceled with one press of the
button.
19
Espresso or coffee
Preparing espresso or coffee
When the . or / buttons are pressed,
the coffee system automatically grinds
the beans to brew the coffee.
SELECT TYPE OF DRINK will appear in
the display.
Place a cup under the coffee
^
dispensers.
^ To make an espresso press the .
button.
or
^
To make a coffee press the / button.
The chosen beverage will now be
dispensed.
Preparing two portions at one
time
You can request two portions of
espresso or coffee at once in one cup
or in two separate cups simultaneously.
To prepare two cups of coffee or
espresso at the same time:
^ Place a cup under each coffee
dispenser.
^ Press the button for the desired drink
twice.
Two portions of the desired drink will be
dispensed from the coffee dispensers.
To ensure that any residues from the
factory testing process are removed
from the brewing system, please
discard the first two cups of coffee
when using the machine for the first
time.
20
Making coffee or espresso using ground coffee
To make espresso or coffee using
ready ground coffee, add a portion of
ground coffee to the ground coffee
chute.
This allows you to prepare a
decaffeinated coffee, if the bean
container is already filled with regular
coffee beans for example.
The coffee machine will automatically
recognize that ground coffee has been
placed in the chute.
Only one portion can be prepared at a
time when using ready ground coffee.
Adding ground coffee
Use the scoop supplied with the
machine to ensure the correct amount
of ground coffee is used.
Do not add more than one level
scoop of ground coffee to the coffee
chute. If too much ground coffee is
added to the ground coffee chute
the brew unit cannot process it.
Open the lid on the right hand side of
^
the coffee machine a.
Open the lid of the ground coffee
^
chute b. Add one level scoop of
ready ground coffee into the ground
coffee chute c.
^ Close both lids.
The following message appears in the
display:
GROUND COFFEE
rYES Bs
^ To prepare the coffee/espresso using
ground coffee, confirm with the
OK button.
The coffee machine uses all the
coffee powder which is put in to
dispense the next drink.
or to cancel preparation with ground
coffee:
^
Turn the rotary selector until NO
appears in the display.
^
Press the OK button.
The ground coffee will be directed into
the waste container.
21
Making coffee or espresso using ground coffee
Making coffee or espresso
using ground coffee
You can now select whether you want
to dispense a coffee or an espresso
made with ground coffee.
If no button is pressed within
approx. 15 seconds, the ground coffee
is emptied into the waste container.
The following message appears in the
display:
SELECT DRINK
USE GROUND COFFEE
^ Place a cup under the coffee
dispensers.
^ To make an espresso press the .
button.
or
^ To make a coffee press the / button.
The desired coffee drink is prepared.
22
Specialty coffees with milk
You can choose from a variety of
specialty coffees. with milk
Cappuccino consists of about
two-thirds milk froth and one-third
espresso.
Latte macchiato consists of one-third
each of hot milk, milk froth and
espresso.
Caffè latte consists of hot milk and
coffee.
Hot milk or milk froth can also be
prepared just as easily.
TIP For best results use cold milk for
making milk froth.
Preparation
Stainless steel milk flask
(depending on the model)
The stainless steel milk container helps
keep the milk cold for longer. Cold milk
gives best results for milk froth.
^ Connect the stainless steel suction
tube to the inside of the lid. Make
sure that the slanted end is pointing
downwards, as shown.
^ Fill the flask with milk up to a
maximum of 3/4"( 2 cm) below the
rim. Place the lid on the flask.
^
Place a container with sufficient milk
beside the coffee machine on the left
hand side.
^
Insert the milk tube into the container.
Make sure that the milk tube is
sufficiently submerged in the milk.
^
Connect the stainless steel angled
end of the milk tube to the top of the
lid until it clicks into place.
^
Place the milk flask on the left hand
side of the coffee machine. Connect
the other end of the milk tube to the
cappuccinatore.
23
Specialty coffees with milk
Making specialty coffees with
milk
Caution! Danger of burning and
scalding from hot steam coming out
of the cappuccinatore. The liquids
and steam dispensed are very hot.
The coffee machine heats up when a
button is pressed to request a drink.
HEATING-UP PHASE will appear in the
display.
Steam is then used to heat the milk in
the cappuccinatore. It can also be
frothed if milk froth is required.
If you have not prepared any milk
drinks for some time, rinse the milk
system before preparing the first
drink. This will remove any bacteria
which may have built up in the milk
tube.
Cappuccino or latte macchiato
Caffè latte, milk froth or hot milk
SELECT TYPE OF DRINK will appear in
the display.
Place a suitable container under the
^
coffee dispensers.
Press the OK button until MENU
^
appears in the display.
MENU
rOTHER DRINKSs
Turn the rotary selector until OTHER
^
DRINKS appears in the display.
Press the OK button.
^ Use the rotary selector to select the
drink you want:
– CAFFÈ LATTE
– MILK FROTH
– HOT MILK
^ Press the OK button.
The desired coffee drink is prepared.
Use a cup for cappuccino or a glass for
latte macchiato.
SELECT TYPE OF DRINK will appear in
the display.
^
Place a suitable container under the
coffee dispensers.
^
To make an espresso press the H
button.
or
^
To make a latte macchiato press the
k button.
The desired coffee drink is prepared.
24
Preparing two portions at one
time
You can select two portions of
cappuccino or latte macchiato at the
same time.
^
Place a suitable container under
each coffee dispenser.
^
Press the button twice for your choice
of cappuccino H or latte macchiato
k.
The drinks will be dispensed.
Loading...
+ 56 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.