Line 6 POD-GO Quick Start Guide
1
1
MODE
TAP
BA
DC
EDIT / EXIT
TUNER
EXP 1
EXP 2
WAH
VOL
ACTION
PAGEPAGE
VIEW
1
16C Pastor of Muppets
[37%]1/16
Delay Transistor Tape
50%48%67%
FeedbackTime Wow/Flutr Scale Mix
PLAY VIEW EDIT VIEW
LOST?
Press to exit all
the way out
Press to toggle
between PLAY VIEW
and EDIT VIEW
Knobs 1-5
Turn to adjust parameters for the
selected block
Press to reset value
Press to toggle between Hz or ms
and note values
Press and hold to jump to the
Bypass/Control page for that
parameter
Press and turn to assign the
parameter to snapshot control
Hold ACTION and press knob to
unassign any controller
Upper Knob
PLAY VIEW: Turn to select presets; press to open
preset list
EDIT VIEW: Turn to select blocks; press to bypass
selected block
ACTION
Press to open action panel for selected block or menu
Press + ACTION to save preset
VOLUME
Turn to control level from Main and Headphone outputs
VIEW
ACTION
PAGEPAGE
WAH
VOL
EXP 1
EXP 2
Full POD Go Owner’s Manual at
line6.com/support/manuals
Video tutorials available at
line6.com/meet-pod-go
Lower Knob
EDIT VIEW: Turn to change
model
Press to open model list
PAGE
Press to view more parameters
for the selected block or item
Press PAGE + PAGE to
open menu with advanced
functions and settings
PRESET Footswitches
Step on footswitch A, B, C, or D
to select a preset
Step on to select the
next/previous bank of presets
Press both and to enter
Snapshot Footswitch Mode
Hold both and to cycle
through Bank, Preset, and
Snapshot Up and Down
STOMP Footswitches FS1-FS6
Step on a footswitch to toggle its block on and off
Press and hold footswitch to assign to the selected block
Press and hold two footswitches to swap assignments
FS3FS2FS1
DC
BA
FS6FS5FS4
MODE
Step on MODE to toggle between Preset and Stomp
Footswitch Modes
MODE
EDIT / EXIT
TAP
TUNER
TAP/TUNER
Step on TAP to set tempo
Hold to open the Tuner
Expression Pedal 1/2
Move the expression pedal
to control volume, wah, or
any combination of amp and
effects parameters
Activate toe switch to toggle
between Wah (EXP 1) and
Volume (EXP 2)
CHEAT SHEET
POD GO
FOOTSWITCH
/ 8
7
RETURN / AUX
FX LOOPGUITAR IN AMP OUT PHONESEXP 2
(STEREO)
SEND
(STEREO)
MAIN OUT
BAL
L / MONO
/ UNBAL
RIGHT
USB DC IN
POWER
GUITAR IN
Connect your guitar,
bass, or synth here
AND
/OR
EXP 2, FS 7/8
Connect a second
expression pedal
or momentary
footswitch here; use
a Y cable to connect
two switches
FX LOOP
Can be used as a mono or
stereo FX Loop for inserting
external stompboxes into your
tone or to connect your amp via
4-Cable Method
The RETURN can be globally set
to act as an always-on, stereo
Aux input
MAIN OUT
Connect to powered speakers;
when connecting to a single
speaker, use the L/MONO output
Use 1/4” TRS > XLR Male cables to
run balanced signals to a mixing
console
AMP OUT
Connect to your
guitar amp’s input.
Echoes the MAIN
OUT signal, but can
be globally set to be
tapped off directly
before the cab/IR
block
PHONES OUT
Connect
headphones here;
turn top panel
VOLUME knob to
adjust level
USB
Connect to your computer
for editing via POD Go
Edit, and for updating
the firmware
POD Go functions as an
audio and MIDI interface
with re-amping built in
PERFORMANCE RECORDING
PHONES
AMP
OUT
MAIN
OUT
OR
Y-CABLE
MAIN
OUTUSB
DC IN/POWER
Line 6 strongly
recommends using
only the included
DC-3h Power
Supply
40-00-0513 Rev C
Loading...