Limiting the Hinges to a 90° Opening Angle .............. 21
R600a Refrigerant
WARNING !
Note to the Installer
It is very important to follow the instructions in the
manual to ensure proper installation and operation of
the unit.
Before installing the unit, be sure to thoroughly read
and understand all of the information in this manual.
WARNING !
Electrocution hazard.
Do not connect to the electrical outlet
before the installation is completed.
2
The refrigerant R600a contained within the
appliance is environmentally friendly, but
flammable. Leaking refrigerant can ignite.
To prevent possible ignition, follow
the warnings below:
•
Keep ventilation openings, in
the appliance enclosure or in
the built-in structure, clear of
obstruction.
• Do not damage the refrigerant
circuit.
• Component parts and power cords shall be
replaced with like components performed by
factory authorized service personnel only.
Page 3
S
afety
Disposal of Old Appliance
DANGER!
Risk of child entrapment.
Child entrapment and suffocation are not problems of
the past.
Junked or abandoned refrigerators are still dangerous –
even if they will sit for “just a few days.”
If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before you discard old appliances:
• Take off the doors.
• Leave the shelves in place so that children
may not easily climb inside.
• Cut off the power cable from the discarded
refrigerator. Discard separately from the
refrigerator.
• Be sure to follow your local requirements for
disposal of appliances.
Electrical Safety
Connect this appliance to a 15 amp or 20 amp, 110120 VAC circuit which is grounded and protected by a
circuit breaker or fuse.
We recommend using a dedicated circuit for this appliance to prevent circuit overload and the chance of
interruption to the appliance.
This appliance is equipped with a three-prong (grounding) polarized plug for your protection against possible
shock hazards.
Where a two-prong wall receptacle is encountered,
contact a qualified electrician and have it replaced with
a properly grounded three-prong receptacle in accordance with all local codes and ordinances.
WARNING!
Electrocution hazard.
Electrical grounding required.
Do not remove the round grounding
•
prong from the plug.
Contact the trash collection agency in
your area for additional information.
Disposal of Packaging Material
WARNING !
Keep packaging materials away from
children. Polythene sheets and bags can
cause suffocation!
If possible, please recycle packaging material at a recycling facility.
Do not use extension cords or
•
ungrounded (two prong) adapters.
• Do not use a power cord that is frayed or
damaged.
• Do not use a power strip.
Failure to follow these instructions may
result in fire, electric shock or death.
Blocking for Safety
WARNING !
To avoid a hazard due to instability of the
appliance, it must be fixed in accordance
with the instructions.
3
Page 4
p
lannIng
I
nformatIon
Appliance Dimensions
MRB 2400MRB 3600MRB 3000
Stated minimum height dimensions include when the levelled feet are fully inserted.
Width will increase by 1/4" (6.5 mm) when mounting strips are installed.
Door Swing Clearance (top view)
MRB 2400MRB 3000MRB 3600
Inset installation style
A = 10 3/4" (273 mm)
B = 1/2" (12.5 mm)
C = 25 7/8" (658 mm)
Inset installation style
A = 13 1/4" (337 mm)
B = 1/2" (12.5 mm)
C = 31 7/8" (810 mm)
Inset installation style
A = 15 3/4" (400 mm)
B = 1/2" (12.5 mm)
C = 37 7/8" (962 mm)
Frameless installation style
A = 11" (279 mm)
B = 1/2" (12.5 mm)
C = 26 3/8" (670 mm)
Dimension A and B: Add panel thickness and handle to calculate distance to wall.
4
Frameless installation style
A = 13 1/2" (343 mm)
B = 1/2" (12.5 mm)
C = 32 3/8" (822 mm)
Frameless installation style
A = 16" (406 mm)
B = 1/2" (12.5 mm)
C = 38 3/8" (975 mm)
Page 5
Cabinet Opening Dimensions
Continous toe kickIndividual toe kick
p
lannIng
I
nformatIon
A
Cabinet depth frameless installation
style = 25" (635 mm)
This is the point where the power
cord exits from the appliance rear.
3/4" (19 mm) from the left and 5"
(127 mm) from the floor.
Free length of the power cord is 98"
(2.5 m).
IMPORTANT
The power plug must be
easily accessible so that
the appliance can be
disconnected from the mains
quickly in an emergency. It
must not be behind the back
of the appliance.
C
The appliance has a recess in this
area for cable and waterline laying.
1" (25 mm) in depth and 5 1/2"
(140 mm) in height over the whole
width of the appliance.
D
This surface is visible when the
appliance door is open. Designed
finish is required.
5
Page 6
p
lannIng
I
nformatIon
Panel Dimensions
24" recess
Inset installation style
H = 79 7/8" (2029 mm)
W = 23 3/4" (603 mm)
Frameless installation style
H = 80" (2032 mm) plus overlapping of the panel on the top
W = 24" (610 mm) plus overlapping of the panel on both sides
Minimum panel thickness = 5/8" (16 mm) *
Maximum panel thickness = 1" (25 mm)
Maximum panel weight = 66 lbs (30 kg)
30" recess
Inset installation style
H = 79 7/8" (2029 mm)
W = 29 3/4" (756 mm)
Frameless installation style
H = 80" (2032 mm) plus overlapping of the panel on the top
W = 30" (762 mm) plus overlapping of the panel on both sides
Minimum panel thickness = 5/8" (16 mm) *
Maximum panel thickness = 1" (25 mm)
Maximum panel weight = 77 lbs (35 kg)
36" recess
Inset installation style
H = 79 7/8" (2029 mm)
W = 35 3/4" (908 mm)
Frameless installation style
H = 80" (2032 mm) plus overlapping of the panel on the top
W = 36" (914 mm) plus overlapping of the panel on both sides
Minimum panel thickness = 5/8" (16 mm) *
Maximum panel thickness = 1" (25 mm)
Maximum panel weight = 88 lbs (40 kg)
* If a “shaker style” panel is used which undershoots
the minimum panel thickness, shorter screws than
those supplied in the accessory pack must be used.a
6
Page 7
Unpacking
1. Cut the straps and
remove them.
2. Press in the lug, tear
or cut the carton on
the edge and remove
it.
3. Remove all styrofoam packing
material from the sides and top.
U
Tx™ 2 0
Tx™ 2 0
7. Remove the safety transportation brackets and anti tipping
device.
Remove the packed cover
strips and support strips from
the appliance rear.
npackIng
4. Remove the box with
mounting parts.
5. Remove the ventilation grille.
6. Secure the appliance door with tape
to prevent it from being opened accidentally.
WARNING !
Risk of injury and damage.
Four people are required to safely remove
the appliance from the bottom pallet.
8. One person tilts the appliance
back carefully and holds it in place.
9. Two people grasp the appliance from the bottom and
lift. One on each side.
DANGER!
Risk of death or serious injury due to
appliance tipping.
Do not remove the transit supports before
the appliance is in the recess.
10. One person removes the pallet.
Place the appliance carefully on the floor.
7
Page 8
U
npackIng
Alternative possibility:
Cut off the marked area from the pallet.
or
Tilt the appliance slightly sideways.
Slide a two-wheeled cart between the appliance and
packaging.
Restrain the appliance to the cart with straps.
Tilt the appliance onto the cart.
Place the appliance carefully on the floor.
Screw length measuring tool
8
Page 9
S
tandard
a
cceSSorIeS
Standard Accessories
Top cover for the door
panel attachment bracket
anti tipping device
Retaining screws for installation
30 pcs.8 pcs.2 pcs.
Tx™ 15
Tx™ 15
16 pcs.20 pcs.
Ventilation grille
20 pcs.
M6 x 12
Tx™ 2 0
Door rack
2 pcs.
10 mm
wrench
Panel
support
strips
Gallon door
rack
Water filter
(MRB 3000 and
MRB 3600 only)
Depth adjustment aid
4 pcs.
Door cover strips
for the panel
supports
Panel support
10 pcs.
Tx™ 15
SmartDeviceBox
Includes component for
Smartphone Connectivity
DO NOT DISCARD!
Forward to appliance user!
TM
keys
Tor x
Divider for ventilation
duct in the toe kick area
Tx™ 10
Appliance cover strips
for the gap between
appliance and recess
or
9
Page 10
B
lockIng for
S
afety
Mounting the anti tipping device
in cabinets deeper than 24" -
Figure 1- 2
To ensure the compressor mounting plate reaches
the anti tipping bracket in cabinets deeper than 24", a
wooden spacer must be mounted between the appliance back and the wall. The anti tipping bracket will
be fastened to the floor downwards and to the spacer
backwards.
WARNING !
Be sure the wooden spacer is fastened
securely to the floor.
Measuring for mounting the wooden spacer on
inset kitchen cabinets - Figure 1
Depth of spacer depending on clearance between appliance and wall
Mounting the anti tipping device
on wooden floors - Figure 3
1. Mark the center line of the appliance on the back
wall. Align the anti tipping bracket center to this line.
WARNING !
Be sure that there is no plumbing or
electrical wiring located in this area which
screws or drills could damage.
2. Fasten bracket to the wooden floor using 5 screws
(1/4" x 2-1/8"). Drill pilot holes if necessary.
3. Fasten bracket with 3 screws (1/4" x 2-1/8") into the
wall plate.
Panel thickness
Figure 1
Measuring for mounting the wooden spacer on
frameless kitchen cabinets - Figure 2
Depth of spacer depending on clearance between appliance and wall
Figure 2
IMPORTANT
If the floor slopes down sideways, the anti-tipping
bracket must be fitted horizontally. Lay down
spacers in the appropriate positions.
Wall
Figure 3
Wall Plate
10
Page 11
Mounting the anti tipping device
on concrete floors - Figure 4 - 5
Secure the appliance in place so it does not tip forward
when the fully stocked door is opened.
bracket is provided with the appliance.
1. Mark the center line of the appliance on the back
wall.
Align the anti tipping bracket center to this line.
WARNING !
Be sure that there is no plumbing or
electrical wiring located in this area which
screws or drills could damage.
2. Drill a 3/8" diameter hole in any position as shown in
Figure 4 using a carbide drill bit.
The depth of the holes must exceed the overall length
of the anchors.
The anti tipping
B
Wall
Wall Plate
lockIng for
Figure 4
S
afety
Clean the holes after drilling.
3. Attach washer and screw on hex nut to the end of
each anchor.
Drive in all 3 anchors.
Align the bracket center to the center line on the back
wall again.
Fasten the anchors by turning the hex nut.
4. Fasten bracket with 3 screws (1/4" x 2-1/8") into the
wall plate (Figure 5).
Wall
Figure 5
Wall Plate
11
Page 12
I
nStallatIon
Safety Instructions and Warnings
for
Water Connection
• Do not install the water connection while the appliance is connected to an electrical outlet.
• The connection to the water supply may only be
made by a trained and licensed plumber.
WARNING !
Connect to potable water supply only.
Water Connection Requirements
• The water pressure must be in the range of
40-90 psi (2.8-6.2 bar).
Failure to meet these requirements may result in
water dispenser malfunction and a water leak that
can damage flooring and surrounding furniture.
• A shut-off valve must be installed between the water
line and the main water supply. It must be easily accessible so the water supply can be stopped
immediately if necessary.
IMPORTANT
Do not install the shut-off valve behind the appliance.
Appliance Installation
Move the appliance towards the final position and leave
enough space to work behind.
Models MRB 3000 and MRB 3600 only
Insert the water line until it comes out
on the appliance rear and pull through.
Models MRB 3000 and MRB 3600 only
Connect the other end to the male
connector and tighten.
The water dispenser on models MRB 3000 and
MRB 3600 is connected using a 1/4" compression fitting.
For the water supply, we recommend
braided style ice maker hoses with
1/4" connectors.
Thread: 7/16-24 UNS
Hose or pipe diameter 1/4"
To connect a 1/4" copper line, use
a 1/4" compression nut and a metal
compression ring.
To connect a 1/4" PEX line, use a 1/4" compression nut
and a plastic compression ring.
A water line is not supplied with the appliance.
IMPORTANT
Do not use any old or already premounted water
supply lines.
IMPORTANT
Make sure that the connection is fitted with a seal
and is tight.
The steel plate can be removed to facilitate
connecting the water hose.
Models MRB 3000 and MRB 3600 only
Remove the cover.
12
Page 13
Models MRB 3000 and MRB 3600 only
I
nStallatIon
Insert the water filter as far as it will go
with the front knobs in a horizontal position
and turn clockwise until it snaps in.
Route the power cord
towards the electrical outlet.
Route the water line towards
the water shut-off valve.
IMPORTANT
Complete the installation
before switching on the
device.
Remove the mounting strip from the
attachment bracket, turn 180° and insert
into the attachment bracket as far as it
will go.
Tx™ 10
Apply the appliance cover strips to
the left and right front edge of the
appliance housing, align in height
with the top profile and screw into
place. The strip is transparent so
the designed mounting holes on
the appliance housing are visible.
We recommend that you mark and
pre-drill the hole positions in the
strip.
Remove the tapes.
Open the door and
remove the transit
support.
IMPORTANT
Use the correct flat head
screws, otherwise the edges
of the cabinet will be damaged
when sliding the appliance into
the recess.
13
Page 14
I
nStallatIon
Mounting the depth adjustment aid into the cover strips
Align the appliance in
depth.
X = Recess front to
appliance housing front
(not cover strip)
Inset 7/8" (22 mm) panel
5
X = 2
/
" (66 mm)
8
Inset 3/4" (19 mm) panel
1
X = 2
/
" (63 mm)
2
Inset 5/8" (16 mm) panel
3
X = 2
/
" (60 mm)
8
Frameless
3
X = 1
/
" (44 mm)
4
Recess
Top vi ew
or
with the depth adjustment aid:
The surface of the depth adjustment aid must be flush with the
surface of the recess. (Example
shows 3/4" (19mm))
14
Slide the appliance into the
recess. To avoid damage,
move the power cord and the
water line at once.
Page 15
Remove the transit supports
using the Torx 25 key.
DANGER!
Risk of death or serious injury due to
appliance tipping.
Do not open the appliance door before the
height adjustment is finished and the antitipping bracket supports the appliance.
I
nStallatIon
Mount the ventilation grille with the grille
segments tilted down.
Remove the depth adjustment aid before fastening the
appliance in the recess.
Turn clockwise to raise the appliance.
Raise the appliance evenly by turning the screws successively until the appliance back touches the antitipping bracket (lift approx. 1/4" / 6.5 mm).
Maximum height adjustment of the appliance = 3/4"(19mm)
IMPORTANT
When turning the screws with a power driver please
consider absolutely.
Maximum rotation speed = 400 rpm
Maximum torque = 8.8 lbs/in (1 Nm)
Fasten the appliance in
the recess through the
appliance cover strips
using eight screws 4 x 14
for each side. We recommend that you mark and
pre-drill the hole positions
in the strip.
Close the front part of the appliance cover
strips.
Hint:
Use the removed transporta-
tion safety component to
help with closing.
Tx™ 15
Failure to follow this instruction will result in
damage to the height adjustment unit.
15
Page 16
I
nStallatIon
Push the mounting strip upwards. The bottom edge of
the mounting strip must be aligned with the top edge of
the adjacent cabinet door.
Inset installation style
Frameless installation style
Position the attachment bracket in the middle
of the door panel, align horizontally and
secure to the door panel using eight
4 x 14 screws.
Tx™ 15
IMPORTANT
Risk of damaging the panel.
Do not undershoot the minimum panel thickness
(shaker style).
Open the door.
Unscrew the attachment bracket with
the mounting strip. Use the 10 mm
wrench provided.
IMPORTANT
When removing, ensure that the
mounting strip does not move.
IMPORTANT
Door handles should be mounted now because the
side support strips will cover the mounting holes.
Only use countersunk
screws for handle mounting.
The holes should be countersunk.
The screw heads should be
flush with the panel.
16
Page 17
Position the panel support strips with the top lug
in the cut of the top attachment bracket.
Align the strips parallel to the side
edge of the panel and screw into
place with ten 4 x 14 screws.
I
nStallatIon
IMPORTANT
If the door has to be limited to a 90° opening angle,
it must be done before the panel is mounted onto
the appliance door. See chapter “Important Note
for Changing over Door Hinges or Limiting the
Hinges to a 90° Opening Angle” on page 21.
Open the appliance door.
Place the door panel on the top adjusting bolts and
align in the centre.
Screw the hex nuts onto the adjusting
bolts and tighten.
Use the 10 mm wrench pro-
vided.
or
Tx™ 15
IMPORTANT
Risk of damaging
the panel.
Do not undershoot
the minimum panel
thickness (shaker
style).
Close the door and check the position of the panel.
IMPORTANT
After a certain time
and loading, it may be
necessary to readjust the
door again.
Tx™ 15
Mount the base of the ventilation duct divider with two
screws 4 x 19.
Click on the cover.
17
Page 18
I
nStallatIon
Align the panel in its vertical
position if necessary.
Loosen the hex nuts
and turn the adusting bolts with the
Torx 15 key provided.
Maximum adjustment: 15 mm (5/8")
Align the panel horizontally with the long
holes in the attachment bracket.
Align the panel in its depth at the bottom.
Loosen the screws, align the panel and tighten the
screws. Use the Torx 20 key provided.
Fasten the panel through the bottom attachment bracket with two screws 4 x 14.
Tighten the hex
nuts. Use the 10 mm
wrench provided.
Align the panel in its
depth.
Loosen the screws,
align the panel and
tighten the screws.
Tx™ 15
IMPORTANT
Risk of damaging the panel.
Do not undershoot the minimum panel thickness
(shaker style).
18
Page 19
I
nStallatIon
Insert the panel supports into the support strips
between panel and appliance door and screw
into place with two screws M6 x 12 each.
Hook the door cover strips at the front of the supports
and snap in at the back.
Tx™ 2 0
19
Page 20
I
nStallatIon
Adjust the brackets to the thickness of the toe kick
panel.
Click cover into place.
Check that there is no gap between the appliance air
divider and the door air divider.
IMPORTANT
There will be a gap if the ventilation grille is fitted
in c orrectly.
Remove the backing foil and affix the toe kick panel.
20
Page 21
Insert the door racks.
The gallon rack must be in
the lowest possible position
of the clip-in strip.
Insert the hooks of the rack into the
openings of the clip-in strip at the
desired height and push down.
I
nStallatIon
Please note in case of removing
appliance from the recess
If the appliance has to be removed from the recess
again, please make sure you take account of the following.
1. Unload the appliance.
2. Disconnect the appliance from the power source.
3. Remove the mounted front panel from the appliance
do or.
4. Lower the appliance using the height adjustment unit.
IMPORTANT
Be sure each door rack is fixed
properly in the clip-in strip.
Model MRB 3000, MRB 3600
Open the shut-off valve for the water supply and
check the entire water system for leaks.
5. Mount the transit supports with
two screws for each support using
a Torx 25 key.
DANGER!
Risk of death or serious injury due to
appliance tipping.
Do not remove the appliance without the
mounted transit supports.
Important Note for Changing
over Door Hinges or Limiting the
Hinges to a 90° Opening Angle
Changing the door hinges or limiting the hinges to a 90°
opening angle should only be carried out by a trained
expert.
The door hinges are fitted with strong closing springs. If
the hinge accidentally snaps shut, this can lead to serious injury.
The door itself is very heavy. Do not try to dismount the
door yourself.
Contact the Liebherr service for more information. See
contact details on the back of this manual.
21
Page 22
For Service in the U.S.
Liebherr Service Center
Toll Free: 1-866-LIEBHER or 1-866-543-2437
Email: Service-appliances.us@liebherr.com
PlusOne Solutions, Inc.
3501 Quadrangle Blvd, Suite 120
Orlando, FL 32817