P/No.: MFL38868723
WD-1031(0~9)FDK WD-1231(0~9)FDK WD-1431(0~9)FDK
P roduct Feature
Direct Drive System
The advanced Brushless DC motor directly drives the drum without belt and pulley.
Water Circulation
Spray detergent solution and water onto the load over and over.
Clothes are soaked more quickly and thoroughly during wash cycle. The detergent suds can be removed more easily by the water shower during rinse cycle. The water circulation system uses both water and detergent more efficiently.
Built-in Heater
Internal heater automatically heats the water to the best temperature on selected cycles.
Child Lock
The Child lock prevents children from pressing any button to change the settings during operation.
Jumbo drum
40% |
LG’s jumbo drum can wash about 40% more load than conventional |
|
|
|
washing machines. A bigger drum improves the wash performance. |
More economical by Intelligent Wash System
Intelligent Wash System detects the amount of load and water temperature, and then determines the optimum water level and washing time to minimize energy and water consumption.
Low noise speed control system
By sensing the amount of load and balance, it evenly distributes load to minimize the spinning noise level.
C ontents |
|
Warnings ............................................................................................................ |
3 |
Specification........................................................................................................ |
4 |
Installation ........................................................................................................... |
5 |
Care before washing ......................................................................................... |
11 |
Adding detergent............................................................................................... |
12 |
Function .......................................................................................................... |
14 |
How to use washer............................................................................................ |
15 |
Maintenance...................................................................................................... |
22 |
Troubleshooting guide....................................................................................... |
26 |
Terms of Warranty ............................................................................................ |
29 |
2
W arnings
READ ALL INSTRUCTIONS AND EXPLANATION OF THE INSTALLATION BEFORE USE
For your safety, the information in this manual must be followed to minimize WARNING! the risk of fire or explosion, electric shock, or to prevent property damage,
personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
WARNING : To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:
•Before installation, check exterior damages. If it has, do not install.
•Do not install or store the washer where it will be exposed to the weather.
•Do not tamper with controls.
•Do not repair or replace any part of the washer or attempt any servicing unless specifically
recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.
•Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.
•Close supervision is necessary if this appliance is used by or near children or infirm persons.
Do not allow them to play on, with, or inside this or any other appliance.
•Keep washer away from fire.
•Do not leave the washer door open.
An open door could entice children to hang on the door or crawl inside the washer.
•Never reach into washer while it is moving. Wait until the drum has completely stopped.
•The laundry process can reduce the flame retardant of fabrics.
•To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.
•Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with
combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.) which may ignite or explode. Oil may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oiled clothes.
•Do not slam the washer door closed or try to force the door open when locked. This could result in damage to the washer.
•When the machine runs high temperature, the front door may be very hot. Don’t touch it.
•To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.
•When unplugging power cord, do not pull out by grasping the cord. Otherwise, the power cord may be damaged.
•Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.
•Before discarding an old machine unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.
•When a product was under water, Please call service center. The risk of electric shock and fire.
Do not push down the door excessively, when washer door open. This could topple over the washer.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinance.
•Do not use an adapter or otherwise defeat the grounding plug.
•If you don’t have the proper outlet, consult an electrician.
WARNING :Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
3
S pecification
Name |
: Front loading washing machine |
||
Power supply |
: 230V~, 50Hz |
|
|
Size |
: 600mm(W) |
645mm(D) 850mm(H) |
|
Weight |
: 64kg |
|
|
Wash capacity |
: 8kg |
|
|
Max. Watt |
: 2000W |
|
|
Spin speed |
: No spin/400/600/800/1000 |
[WD-1031(0~9)FDK] |
|
|
No spin/400/800/1000/1200 |
[WD-1231(0~9)FDK] |
|
|
No spin/400/800/1000/1400 |
[WD-1431(0~9)FDK] |
|
Water consumption |
: 56 (7 /Kg) |
|
|
Permissible water pressure |
: 0.3-10kgf/ |
(30-1000kPa) |
|
The appearance and specifications may be varied without notice to raise the units quality.
Accessories
Inlet hose(1EA) |
Spanner |
4
I nstallation
Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.
Properly ground washer to conform with all governing codes and ordinances.
The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
In countries where there are areas which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in clean condition at all times.
Any damage which may be cause by cockroaches or other vermin will not be covered by the appliance guarantee.
Transit bolts
The appliance is fitted with transit bolts to prevent internal damage during transport.
• Packing and all transit bolts must be removed before using the washer.
When unpacking the base, be sure to remove the additional packing support in the middle of the base packing.
Removing transit bolts
1. To prevent internal damage during transport, the special 4 bolts are locked. Before operating the washer, remove the bolts along with the rubber bungs.
• If they are not removed, it may cause heavy vibration, noise and malfunction.
2. Unscrew the 4 bolts with the spanner supplied.
I nstallation
Installation place requirement
Level floor :
Allowable slope under entire washer is 1˚
Power outlet :
Must be within 1.5 meters of either side of location of washer. Do not overload the outlet with more than one appliance.
Additional Clearance :
For wall, door and floor modeling is required. (10cm : rear / 2cm: right & left side)
Do not place or store laundry products on top of washer at any times.
They can damage the finish or controls.
650
850
600
Positioning
Install the washer on a flat hard floor.
Make sure that air circulation around the washer is not impeded by carpets,rug etc.
•Never try to correct any unevenness in the floor with pieces of wood, cardboard or similar materials under the washer.
•If it is impossible to avoid positioning the washer next to a gas cooker or coal burning stove,an insulating(85x60cm) covered with aluminum foil on the side facing the cooker or stove,must be inserted between the two appliance.
•The washer must not be installed in rooms where the temperature can drop below 0°C.
•Please ensure that when the washer is installed, it is easily accessible for the engineer in the event of a breakdown.
•With the washer installed adjust all four feet using the transit bolt spanner provided ensuring the appliance is stable, and a clearance of approximately 20mm is left between the top of the washer and the underside of the work-top.
6
I nstallation
Electrical connection
1. Do not use an extension cord or double adapter.
2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agents or similarly qualified person in order to avoid a hazard.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible.
•Repairs to the washing machine must only be carried out qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service center
•Do not install your washing machine in rooms where temperatures below freezing may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.
•If the appliance is delivered in the winter months and temperatures are below freezing : Store the washing machine at room temperature for a few hours before putting it into operation.
CAUTION
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Washing Machine is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.
Connecting water supply hose
Hose connector |
Rubber seal |
Water supply pressure must be between 30kPa and 1000kPa (0.3~10kgf/cm2) Don’t strip or crossthread when connecting Inlet hose to the valve.
If the water supply pressure is more than 1000kPa, a decompression device should be installed.
•Two rubber seals are supplied with the water inlet hoses these are in order to prevent water leaks.
•Check water tightness of washing machine connections by turning the tap completely on.
•Periodically check the condition of the hose and replace the hose if necessary.
•Make sure that there is no kink on the hose and that it is not crushed.
NOTE After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.
7
I nstallation
Normal Tap without thread & screw type inlet hose
1. Unscrew the fixing screw to attach the tap.
2. Push the connector up till the rubber packing is in tight contact with the tap. Then tighten the 4 screws.
3. Push the water supply hose vertically upwards so that the rubber packing within in the hose can adhere completely to the tap and then tighten it by screwing it to the right.
Normal Tap without thread & one touch type inlet hose
1. Untighten the upper connector |
2. Push the upper connector up till |
|
screw. |
|
the rubber packing is in tight |
|
|
contact with the tap. Then |
Upper |
Rubber |
tighten the 4 screws. |
Connector |
packing |
|
Fixing screw |
Middle |
Rubber packing |
|
||
|
connector |
|
|
|
Upper |
• In case the diameter of the tap is |
Connector |
|
|
||
large remove the guide plate. |
Middle |
|
|
|
connector |
3.Connect the water supply hose to the middle connector, pushing the plate down.
Upper
Connector
Plate
Water supply 
hose 
Guide plate
Connector
Used the horizontal tap
Horizontal tap
• Turn the middle connector not |
• To separate the water supply |
|
to have water leaked. |
hose from the middle connector |
|
• Make sure that the rubber seal |
shut off the tap. Then pull the |
|
inlet hose down, pushing the |
||
is inside the hose connector. |
||
plate down. |
||
|
||
Hose connector |
|
|
Rubber seal |
|
Extension tap |
|
Square tap |
• Your machine comes with |
only cold water connection. |
|
|
• Make sure that there are no |
|
kinks in the hose and that it |
|
is not crushed. |
8
Loading...