<![endif]>ESPAÑOL ENGLISH
OWNEr’S MANuAL
DrYer
Please read this owner’s manual thoroughly before operating and keep it handy for reference at all times.
DleY2139eK1 DlGY2139eK1
|
|
|
|
|
|
|
|
|
|
|
www.lg.com |
MFL67731030 |
|
|
|
|
|||||||
2 TABLE OF CONTENTS
TABLE OF CONTENTS
3 |
IMPORTANT SAFETY INSTRUCTIONS |
35 |
MAINTENANCE |
||
|
|
|
|
|
|
|
|
35 |
Regular Cleaning |
||
3 |
What to Do if You Smell Gas |
||||
4 |
Basic Safety Precautions |
|
|
|
|
5 |
Grounding Instructions |
36 |
TROUBLESHOOTING |
||
5 |
Safety Instructions for Installation |
||||
|
|||||
7 |
Safety Instructions for Connecting |
|
|
|
|
36 |
Before Calling for Service |
||||
|
|
||||
Electricity
8PRODUCT features
9INTRODUCING YOUR DRYER
38SPECIFICATIONS
39USING SMART DIAGNOSISTM
9 Parts
9Accessories
10Control Panel Features
11Display
12INSTALLATION INSTRUCTIONS
12Preview Installation Order
13Installation Location Requirements
13Clearances
14Leveling the Dryer
15Reversing the Door
16Installing the Side Vent Kit
17Venting the Dryer
19Connecting Inlet Hose
20Connecting Gas Dryers
22Connecting Electric Dryers
27Special Requirements for Manufactured or Mobile Homes
27Final Installation Check
28Installation Test (Duct Check)
30 HOW TO USE
30 Operating the Dryer
31Cycle Guide
32Sorting Load
32 Loading the Dryer
32Check the Lint Filter Before Every Load
33Cycle Settings and Options
34Special Functions
34 Custom Program
34 Steam Functions
IMPORTANT SAFETY INSTRUCTIONS 3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
w This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION. These words mean:
wDANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
wWarning
You can be killed or seriously injured if you don’t follow instructions.
wcaution
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
•Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.
•Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance or any other appliances.
•Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
•Install the clothes dryer according to the manufacturer’s instructions and local codes.
•Save these instructions.
WHAT TO DO IF YOU SMELL GAS:
1.Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2.Do not touch any electrical switches. Do not use any phone in your building.
3.Clear the room, building, or area of all occupants.
4.Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.
5.If you cannot reach your gas supplier, call the fire department.
<![endif]>ENGLISH
4 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
BASIC SAFETY PRECAUTIONS
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•Read all instructions before using the dryer.
•Before use, the dryer must be properly installed as described in this manual.
•Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
•Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.
•Do not reach into the dryer if the drum or any other part is moving.
•Do not repair or replace any part of the dryer or attempt any servicing unless specifically
recommended in this owner’s manual or in published user-repair instructions that you understand and have the skills to carry out.
•Do not tamper with controls.
•Before the dryer is removed from service or discarded, remove the door to the drying compartment.
•Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.
•Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.
•Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.
•Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.
•The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.
•Do not install or store the dryer where it will be exposed to the weather.
•Always check the inside of the dryer for foreign objects.
•Clean lint screen before or after each load.
•Do not store plastic, paper, or clothing that may burn or melt on top of the dryer during operation.
IMPORTANT SAFETY INSTRUCTIONS 5
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be
equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
Electric shock can result if the dryer is not properly grounded.
wWarning
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt that the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
•Properly ground dryer to conform with all governing codes and ordinances. Follow details in the installation instructions. Electric shock can result if the dryer is not properly grounded.
•Before use, the dryer must be properly installed as described in this manual. Electric shock can result if the dryer is not properly grounded.
•Install and store the dryer where it will not be exposed to temperatures below freezing or exposed to the weather.
•All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this owner’s manual. Use only authorized factory parts. Failure to follow this
warning can cause serious injury, fire, electric shock, or death.
•To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning can cause serious injury, fire, electric shock, or death.
•Connect to a properly rated, protected, and sized power circuit to avoid electrical overload. Improper power circuit can melt, creating electric shock and/or fire hazard.
•Remove all packing items and dispose of all shipping materials properly. Failure to do so can result in death, explosion, fire, or burns.
•Place dryer at least 18 inches above the floor for a garage installation. Failure to do so can result in death, explosion, fire, or burns.
•Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.
•Do not install near another source of heat such as a stove, cooking oven. Failure to do so can cause deform, smoke and fire.
•Do not place candles, smoking materials, or other flammables on top of the product. Dripping wax, smoke, or fire can result.
•Remove all protective vinyl film from the product.
Failure to do so can cause product damage, smoke or fire.
<![endif]>ENGLISH
6 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWarning
To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death.
Exhaust/Ducting:
•Gas dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire or death.
•The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard.
•Use only rigid metal or flexible metal 4-inch diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork can cause a fire. Punctured ductwork can cause a fire if it collapses or becomes otherwise restricted in use or during installation.
•Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally.The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 inches (10.2 cm) in diameter with no obstructions.The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new
dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semi-rigid metal ducting is recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a ULlisted flexible metal transition duct may be used between the dryer and wall connection only.The use of this ducting will affect drying time. Failure to follow these instructions can result in fire or death.
•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in fire or death.
IMPORTANT SAFETY INSTRUCTIONS 7
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWarning
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the ground prong from the power cord. To prevent injury to persons or damage to the dryer, the electrical power cord must be plugged into a properly grounded outlet.
•For personal safety, this dryer must be properly grounded. Failure to do so can result in electric shock or injury.
•Refer to the installation instructions in this manual for specific electrical requirements for your model.
Failure to follow these instructions can create an electric shock hazard and/or a fire hazard.
•This dryer must be plugged into a properly grounded outlet. Electric shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Failure to follow these instructions can create an electric shock hazard and/or a fire hazard.
•The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides sparkling performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
•Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. The power cord can be damaged, resulting in a risk of fire and electric shock.
•Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt, creating an electric shock and/or fire hazard.
•When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord. This will prevent injury and prevent damage to the dryer from fire and electric shock.
<![endif]>ENGLISH
SAVETHESE INSTRUCTIONS
8 PRODUCT features
PRODUCT FEATURES
Easy-to-USE Control Panel
An entire selection of user-friendly functions make operating the dryer easy.
EASY-ACCESS REVERSIBLE DOOR
The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to adjust for installation location.
STEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and make ironing easier. Simply select the Steam Fresh™ cycle or Wrinkle Care cycle.
Flow Sense™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The Flow Sense™ duct blockage sensing system detects and alerts you to restrictions in the installed household ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying times caused by blocked ducts.
Smart Diagnosis™
Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your telephone to the Customer Information Center. The call center agent records the data transmitted from your machine and uses it to analyze the issue, providing a fast and effective diagnosis.
INTRODUCING YOUR DRYER
Parts
INTRODUCING YOUR DRYER 9
<![if ! IE]><![endif]>ENGLISH
Control
panel
Leveling
feet
Reversible |
Terminal |
Power cord |
door |
block |
location |
|
access panel |
(Gas |
|
(Electric |
models) |
|
models) |
|
|
|
Water inlet |
|
Gas |
valve |
|
|
|
Lint filter |
connection |
Exhaust |
|
location |
|
|
duct |
|
|
(Gas models) |
|
|
outlet |
|
|
|
Accessories
Included accessories |
Optional accessories |
|
|
|
Side vent kit |
|
Y connector |
Hose |
Drying rack |
(sold separately) |
|
Kit No. |
||||
|
|
|
||
|
|
|
383EEL9001B |
NOTE
•Contact LG Customer Service at if any accessories are missing.
•For your safety and for extended product life, use only authorized components.The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized components or parts.
•The images in this owner’s manual may be different from the actual components and accessories, and are subject to change by the manufacturer without prior notice for product improvement purposes.
10 INTRODUCING YOUR DRYER
Control Panel Features
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information.
wWarning
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety Instructions, before operating this dryer.
G F A
D E
A POWER ON/OFF BUTTON
Press to turn the dryer ON. Press again to turn the dryer OFF.
NOTE
Pressing the ON/OFF button during a cycle will cancel that cycle and any load settings will be lost.
H B C
D MORETIME/LESSTIME BUTTONS
Use these buttons with the Time Dry and other MANUAL DRY cycles to adjust the drying time. Press the More Time button to increase the selected manual cycle time by one minute; press Less Time to decrease the cycle time by one minute.
B CYCLE BUTTONS
Press the Cycle button repeatedly to scroll through the cycle selections until the desired cycle is selected. The standard presets for the selected cycle will be shown in the display. On MANUAL DRY cycles, these settings can be
adjusted using the cycle setting buttons anytime before starting the cycle.
C START/PAUSE BUTTON
Press this button to start the selected cycle. If the dryer is running, use this button to pause the cycle without losing the current settings.
NOTE
If you do not press the START/PAUSE button to resume a cycle within 4 minutes, the dryer turns off automatically.
E CYCLE SETTING BUTTONS
Use these buttons to select the desired cycle settings for the selected cycle. The current settings are shown in the display. Press the button for that option to select other settings.
F TIME AND STATUS DISPLAY
The display shows the settings, estimated time remaining, options, and status messages for your dryer.
G OPTION BUTTONS
The option buttons allow you to select additional cycle options. Certain buttons also allow you to activate special functions by pressing and holding the button for 3 seconds.
H STEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and make ironing easier. Simply select the Steam Fresh™ cycle or Wrinkle Free cycle.
INTRODUCING YOUR DRYER 11
Display
The display shows the settings, estimated time remaining, options, and status messages for your dryer. When the dryer is turned on, the lights in the display will illuminate.
wWarning
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety Instructions, before operating this dryer.
<![endif]>ENGLISH
F |
D |
B |
C |
A Estimated Time Remaining
This display shows the estimated time remaining for SENSOR DRY cycles or the actual time remaining for Time Dry or MANUAL DRY cycles.
NOTE
The cycle time on SENSOR DRY cycles may fluctuate as the dryer recalculates drying time for optimal results.
BCYCLE COMPLETION INDICATOR WITH CHECK FILTER REMINDER
This portion of the display shows which stage of the drying cycle is currently underway (Clean Filter, Drying, Cooling).
E A
D CLEAN FILTER reminder
The display will show Clean Filter when the dryer is turned on as a reminder to check the filter. It turns off when the START/PAUSE button is pressed.
E CUSTOM PROGRAM
If you have a special combination of settings that you use frequently, you can save these settings as a Custom Program.
C Child Lock Indicator
When Child Lock is set, the Child Lock indicator will appear and all buttons are disabled except the POWER button. This prevents children from changing settings while the dryer is operating.
FFlow Sense™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The Flow Sense™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. Maintaining a clean exhaust system improves operating efficiency and helps minimize service calls, saving your money.
12 INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Preview installation order
Checking and |
Leveling the dryer |
Venting the dryer |
choosing the proper |
|
|
location |
|
|
Connecting the inlet hose |
Connecting gas |
Connecting electric |
|
|
|
dryers |
dryers |
120V |
240V |
|
|
|
|
Press and hold |
|
Plugging in the |
|
Installation test |
Test run |
power cord and |
|
(Refer to page 28.) |
|
grounding |
|
|
|
|
|
|
|
INSTALLATION INSTRUCTIONS 13
Installation Location Requirements
wWarning
Read all installation instructions completely before installing and operating your dryer! It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.
• A location that allows for proper exhaust installation. A |
• A sturdy floor to support the total dryer weight of 200 |
gas dryer must be exhausted to the outdoors. |
lbs (90.7 kg). The combined weight of a companion |
See Venting the dryer. |
appliance should also be considered. |
• A grounded electrical outlet located within 2 ft. |
• No other fuel-burning appliance can be installed in the |
(61 cm) of either side of the dryer. See Connecting |
same closet as a dryer. |
electric dryers. |
|
Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.
NOTE
•A level floor with a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5 cm), install the Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not operate correctly if dryer is not level.
•For a garage installation, you will need to place the dryer at least 18 inches (46 cm) above the floor. If using a pedestal, you will need 18 inches (46 cm) to the bottom of the dryer.
Clearances
14" max.* |
|
|
|
(7.6 cm) |
|
|
|
|
|
|
|
(35.6 cm) |
|
|
|
|
|
21 1/4" |
|
|
|
|
|
(54 cm) |
|
|
|
|
|
|
40 3/16" |
|
|
|
|
|
(102 cm) |
|
|
|
|
28 15/16" |
5"** |
(2.54 cm) |
(68.6 cm) |
(2.54 cm) |
|
(73.4 cm) |
(12.7 cm) |
Closet Door Vent |
|||
50 1/4" |
|
|
|
(7.6 cm) |
|
|
|
|
Requirements |
||
(127.5 cm) |
|
|
|
|
|
Installation spacing for recessed area or closet installation
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of
1 inches(2.54cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:
•Additional spacing should be considered for ease of installation and servicing.
•Additional clearances might be required for wall, door and floor moldings.
NOTE
•Additional spacing should be considered on all sides of the dryer to reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.
•Companion appliance spacing should also be considered.
<![endif]>ENGLISH
There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of vibration from one to the other. Too much vibration, it could cause them to make noise or touch each other causing paint damage and making even more noise.
14 INSTALLATION INSTRUCTIONS
Clearances (cont.)
Recommended installation spacing for cabinet installation
• For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.
*Required spacing
**For side or bottom venting,
2 inches (5.1 cm) spacing is allowed.
7"* (17.8 cm) 7"* (17.8 cm)
5"* |
28 |
1"* |
1" |
|
|
|
|
27 " |
|
|
|
1" |
|
|
|
|
|||||||||
(12.7 cm) (73.4 cm) |
(2.5 cm) |
(2.54 cm) |
(68.6 cm) |
(2.54 cm) |
||||||||
Leveling the Dryer
wWarning
•To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses.
Failure to follow this warning can cause serious injury or death.
•The appliances are heavy. Two or more people are required when installing the dryer. Failure to follow this warning can cause serious injury or death.
To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.
NOTE
Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.
1.Position the dryer in the final location. Place a level across the top of the dryer.
•All four leveling feet must rest solidly on the floor.
Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal, you must use the leveling feet on the pedestal to level the dryer. The dryer leveling feet should be fully retracted.
2.Use an adjustable wrench to turn the leveling feet. Turn clockwise to raise the dryer or counterclockwise to lower it. Raise or lower the leveling feet until dryer is level from side to side and front to back.
Make sure that all 4 leveling feet are in firm contact with the floor.
Level
Leveling Feet
INSTALLATION INSTRUCTIONS 15
Reversing the Door
wWarning
•To avoid damage to the dryer or the door, support the door with a stool or box that fits under the door, or have an assistant support the weight of the door.
•Avoid dropping the door to avoid damage to the door or the floor.
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure to follow the instructions below can result in damage to the dryer, property damage or injury to persons.
1.Open the door and remove the two plastic hole caps on the catch side by gently prying up with a flat blade screwdriver. Save these for step 6.
Hole cap
2.While supporting the door, remove the 4 screws, two from each hinge. Set the door aside face down on a protected surface to prevent damage to the door or the work surface.
Hinge screw |
4.Remove the 4 screws securing the hinges to the door frame. Remove the two plastic cover caps. Reinstall the hinges and cover caps on the opposite sides from which they were removed.
Hinge assembly
Cover cap
5.With the hinges and cover caps in the new locations, remount the inner door frame onto the outer door frame with the screws removed in step 3 above.
6. Reinstall the door with the screws from steps 1,2.
<![endif]>ENGLISH
3.With the door on a protected surface, remove the 12 screws on each side of the door and lift off the inner door frame using a flat blade screwdriver. Remove the latch hook and blank and move them to the opposite side.
6.Test the swing of the door to make sure the hinges and latch are properly aligned and that the door closes and latches correctly.
Inner door frame
Latch hook
Swing Door
16 INSTALLATION INSTRUCTIONS
Installing the Side Vent Kit
wWarning
•Use a heavy metal vent.
•Do not use plastic or thin foil duct.
•Clean old ducts before installing this dryer.
•To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses.
•Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons, or death.
Your new dryer is shipped to vent to the rear.
It can also be configured to vent to the bottom or side (right-side venting is not available on gas models).
An adapter kit, part number 383EEL9001B, may be purchased from your LG retailer. This kit contains the necessary duct components to change the dryer vent location.
1.Remove the rear exhaust duct retaining screw. Pull out the exhaust duct.
Retaining
Screw
Rear 
Exhaust Duct
OPTION 1: Side Venting
2.Press the tabs on the knockout and carefully remove the knockout for the desired vent opening (rightside venting is not available on gas models). Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.
Adapter
Duct
Bracket
Knockout 
3.Preassemble a 4 inches (10.2 cm) elbow to the next 4-inches (10.2 cm) duct section, and secure all joints with duct tape. Be sure that the male end of the elbow faces AWAY from the dryer. Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure in place with duct tape.
Be sure that the male end of the duct protrudes 1½ inches (3.8 cm) to connect the remaining ductwork.
Attach cover plate to the back of the dryer with included screw.
Cover
Plate
Elbow |
11/2” |
|
(3.8 cm) |
OPTION 2: Bottom Venting
2.Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.
Adapter
Duct
Bracket 
3.Insert the 4 inches (10.2 cm) elbow through the rear opening and press it onto the adapter duct. Be sure that the male end of the elbow faces down through hole in the bottom of the dryer. Secure in place with duct tape.
Attach the cover plate to the back of the dryer with included screw.
Cover 
Plate
Elbow
INSTALLATION INSTRUCTIONS 17
Venting the Dryer
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not crush or collapse ductwork. Failure to follow these instructions can result in fire or death.
•Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions can result in fire or death.
•If connecting to existing ductwork, make sure it is suitable and clean before installing the dryer.
Failure to follow these instructions can result in fire or death.
•Venting must conform to local building codes.
Failure to follow these instructions can result in fire or death.
•Gas dryers MUST exhaust to the outdoors.
Failure to follow these instructions can result in fire or death.
•Use only 4-inch (10.2 cm) rigid or flexible metal ductwork inside the dryer cabinet and for venting outside. Failure to follow these instructions can result in fire or death.
•To reduce the risk of fire, combustion, or accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to follow these instructions can result in fire or death.
•To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting.
Failure to follow these instructions can result in fire or death.
•The exhaust duct must be 4 inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow these instructions can result in fire or death.
•Rigid or semirigid metal ducting is recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a UL-listed flexible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect drying time. Failure to follow these instructions can result in fire or death.
•DO NOT use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. Failure to follow these instructions can result in fire or death.
•To maximize operating results, please observe the duct length limitations noted in the chart next page. Failure to follow these instructions can result in fire or death.
•Ductwork is not provided with the dryer. You should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions can result in fire or death.
•The total length of flexible metal duct shall not exceed 8 ft. (2.4 m)
•In Canada, that only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer shall be used. In the United States, that only those foil-type flexible ducts, if any, specifically identified for use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject 2158A, shall be used.
<![endif]>ENGLISH
18 INSTALLATION INSTRUCTIONS
Venting the Dryer (cont.)
Ductwork |
|
|
|
|
Number of |
MaximumLengthof |
Correct Venting |
Wall Cap Type |
90° Elbows |
4-inchDiameter |
|
|
|
RigidMetalDuct |
|
Recommended |
0 |
65 ft. (19.8 m) |
|
|
1 |
55 ft. (16.8 m) |
|
4” |
2 |
47 ft. (14.3 m) |
|
(10.2 cm) |
|
||
|
3 |
36 ft. (11.0 m) |
|
4” |
4 |
28 ft. (8.5 m) |
|
(10.2 cm) |
|
||
Use only for |
0 |
55 ft. (16.8 m) |
|
short run |
1 |
47 ft. (14.3 m ) |
|
installations |
|
||
|
2 |
41 ft. (12.5 m) |
|
|
3 |
30 ft. (9.1 m) |
|
22/4" |
|
|
|
(6.35 cm) |
4 |
22 ft. (6.7 m) |
Incorrect Venting |
|
|
|
NOTE
Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.
Routing and Connecting Ductwork
NOTE
Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork.
Ductwork and fittings are NOT included and must be purchased separately.
•Use 4-inch (10.2 cm) diameter rigid or semirigid metal ductwork.
•The exhaust duct run should be as short as possible.
•Use as few elbow joints as possible.
•The male end of each section of exhaust duct must point away from the dryer.
•Use duct tape on all duct joints.
•Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.
•Incorrect or inadequate exhaust systems are not covered by the dryer warranty. Failures or poor performance caused by such exhaust systems will not be covered by the dryer warranty.
INSTALLATION INSTRUCTIONS 19
Connecting Inlet Hose
The dryer must be connected to the cold water tap using the new water supply hose. Do not use old hoses
NOTE
•Water supply pressure must be between 21.8 PSI and 116 PSI (150~800 kPa).
•Do not strip or cross-thread when connecting inlet hose to the valve.
•If the water supply pressure is more than 800 kPa, a decompression device should be installed.
•Periodically check the condition of the hose and replace the hose if necessary.
•Replace inlet hoses after 5 years of use to reduce the risk of hose failure.
•Record hose installation or replacement dates on the hoses for future reference.
1.Check rubber seal in the inlet hose. Two rubber seals are supplied with each inlet hose. They are used for preventing water leaks. Make sure the connection to the cold water tap is tight.
Hose 
connector 
Rubber 
seal
Y connector
2. Check the installation type.
Short |
Long |
hose |
hose |
Y connector |
|
WITH WASHER |
WITHOUT WASHER |
Connect all water supply hoses tightly by hand and then tighten another 2/3 turn with pliers.
WITH WASHER: When connecting the dryer to the same faucet as a washer.
a.Shut off the cold water tap and remove the washer hose.
b.Connect the short hose to the Y-connector using one of the hose washers.
c.Connect the other end of the short hose to the cold water faucet.
d.Connect the long dryer hose to one side of theY-connector and connect the washer hose to the other side.
WITHOUT WASHER: If the dryer does not share the
cold water tap with a washer.
a.Connect the straight end of the long hose to the cold water faucet.
NOTE
•Before connecting the water line to the dryer, flush several gallons of water into a drain or bucket. This will help prevent foreign particles such as sand and scale from clogging the dryer inlet valve.
•Do not overtighten. Damage to the coupling can result.
3. Connect the hose to the dryer.
•Connect the water supply hose to the dryer inlet valve tightly by hand and then tighten another 2/3 turn with pliers.
Make sure that there are no kinks in the hoses and that they are not crushed.
4. Turn on the cold water faucet.
5.Check for leaks at the Y-connector (if used) and in all hoses.
NOTE
•If any leaks are found, shut off the water faucet, remove the hose and check the condition of the hose washer.
<![endif]>ENGLISH
20 INSTALLATION INSTRUCTIONS
Connecting Gas Dryers wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Gas supply requirements:
As shipped from the factory, this dryer is configured for use with natural gas. It can be converted for use with LP (Liquefied Propane) gas. Gas pressure must not exceed 13 inches of water column.
•A qualified service or gas company technician must connect the dryer to the gas service.
Failure to do so can result in fire, explosion, or death.
•Isolate the dryer from the gas supply system by closing its individual manual shutoff valve during any pressure testing of the gas supply. Failure to do so can result in fire, explosion, or death.
•Supply line requirements:
Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1⁄ - inch NPT pipe plug must be installed.
Failure to do so can result in fire, explosion, or death.
•If using a rigid pipe, the rigid pipe should be ½ - inch IPS. If acceptable under local codes and ordinances and when acceptable to your gas
supplier, 3⁄ - inch approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do so can result in fire, explosion, or death.
Electrical requirements for gas models only
wWarning
•Connect the dryer to the type of gas shown on the nameplate. Failure to do so can result in fire, explosion, or death.
•To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so can result in fire, explosion, or death.
•DO NOT use an open flame to inspect for gas leaks. Use a noncorrosive leak-detection fluid. Failure to do so can result in fire, explosion, or death.
•Use only a new AGAor CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so can result in fire, explosion, or death.
•Securely tighten all gas connections. Failure to do so can result in fire, explosion, or death.
•DO NOT attempt any disassembly of the dryer; any disassembly requires the attention and tools of an authorized and qualified service person or company. Failure to do so can result in fire, explosion, or death.
•Use a pipe-joint compound that is insoluble in Liquefied Petroleum (LP) gas on all pipe threads.
Failure to do so can result in fire, explosion, or death.
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can result in fire, explosion, or death.
•For personal safety, this dryer must be properly grounded. Failure to follow this warning can result in fire, explosion, or death.
•The power cord of this dryer is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. Failure to follow this warning can result in fire, explosion, or death.
•This dryer must be plugged into a 60 Hz, 120 VAC, grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to follow this warning can result in fire, explosion, or death.
•Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can result in fire, explosion, or death.
INSTALLATION INSTRUCTIONS 21
Connecting Gas Dryers (cont.)
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Installation and service must be performed by a qualified installer, service agency, or the gas
supplier. Failure to do so can result in fire, explosion, or death.
•Use only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so can result in fire, explosion, or death.
•A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer is configured for Natural Gas when shipped from the factory. Make sure that the dryer is equipped with the correct burner orifice for the type of gas being used (Natural Gas or Liquefied Petroleum). Failure to do so can result in fire, explosion, or death.
•If necessary, the correct orifice (For the LP orifice kit, order part number 383EEL3002D) should be installed by a qualified technician and the change should be noted on the dryer. Failure to do so can result in fire, explosion, or death.
•All connections must be in accordance with local codes and regulations. Failure to do so can result in fire, explosion, or death.
•Gas dryers MUST exhaust to the outdoors. Failure to do so can result in fire, explosion, or death.
Connecting the gas supply
1.Make sure that the gas supply to the laundry room is turned OFF. Confirm that the type of gas available in
your laundry room is appropriate for the dryer. The dryer is prepared for Natural Gas with a 3⁄ - inch NPT gas connection.
2.Remove the shipping cap from the gas connection at the back of the dryer. Be careful not to damage the threads of the gas connector when removing the shipping cap.
3.Connect the dryer to your laundry room’s gas supply using a new flexible stainless steel connector with a 3⁄ - inch NPT fitting.
4.Securely tighten all connections between the dryer and your laundry room’s gas supply. Turn on your laundry room’s gas supply and check all pipe
connections (both internal and external) for gas leaks with a noncorrosive leak-detection fluid.
Electrical connection
3/8” NPT Gas
Connection
AGA/CSA-Certified Stainless Steel Flexible Connector
Plug dryer into a 120 VAC, 60 Hz grounded 3-prong outlet.
1/8” NPT Pipe
Plug
Gas Supply
Shutoff Valve
High-altitude installations
The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.
If your gas dryer is being installed at an elevation above
10,000 feet, it must be derated by a qualified technician or gas supplier.
<![endif]>ENGLISH
22 INSTALLATION INSTRUCTIONS
Connecting Electric Dryers
wWarning
To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code,
ANSI/NFPA 70 and all applicable local regulations.
Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.
Electrical requirements for electric models only
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
• This dryer must be connected to a grounded metal, permanent wiring system, or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the dryer. Failure to do so can result in fire, explosion, or death.
•The dryer has its own terminal block that must be connected to a separate 240 V 60-Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT CIRCUIT. Failure to follow these instructions can result in fire, explosion, or death.
•If branch circuit to dryer is 15 ft. (4.5 m) or less in length, use UL (Underwriters Laboratories) listed No.-10 AWG wire (copper wire only), or as required by local codes. If over 15 ft. (4.5 m), use UL-listed No.-8 AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring
so dryer can be moved from its normal location when necessary. Failure to do so can result in fire, explosion, or death.
•The power cord (pigtail) connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages. Failure to follow these instructions can result in fire, explosion, or death.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so can result in fire, explosion, or death.
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Do not modify the plug and internal wire provided with the dryer.
•The dryer should be connected to 4-hole outlet.
•If it does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.
wWarning
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:
•Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 3280 or Standard CAN/ CSA Z240 MH and local codes and ordinances.
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996. Failure to do so can result in fire, explosion, or death.
INSTALLATION INSTRUCTIONS 23
Connecting Electric Dryers (cont.) USA only
wWarning
•Connect the power cord to the terminal block. Connect each power cord wire to the terminal block screw that has the same colored wire. For example, connect the black power cord wire to the terminal block screw with the black wire. Failure to follow these instructions may result in a short, overload, fire or death.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations,
(2) mobile homes, (3) recreational vehicles, and
(4) areas where local codes prohibit grounding through the neutral conductor.
Four-wire connection for electric dryers: Power cord
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
1.Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed,
30 A, 240 V, 4-wire, #10 AWG-minimum copper conductor power cord through the strain relief.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed
4-Wire Power
Cord
•Use a 30 A, 240 V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.
2.Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cord to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cord ground wire to the green ground screw. Tighten alL screws securely. Reinstall the terminal block access cover.
Hot |
Neutral |
|
(Black) |
(White) |
|
Ground |
Hot |
|
(Red) |
||
Screw |
||
|
|
White Wire |
|
moved from |
Power Cord |
Ground Screw |
|
|
Ground Wire |
|
<![endif]>ENGLISH
24 INSTALLATION INSTRUCTIONS
Connecting Electric Dryers (cont.) USA only
wWarning
•Connect the power cord to the terminal block. Connect each power cord wire to the terminal block screw that has the same colored wire. For example, connect the black power cord wire to the terminal block screw with the black wire.
Failure to follow these instructions may result in a short, overload, fire or death.
•Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations,
(2) mobile homes, (3) recreational vehicles, and
(4) areas where local codes prohibit grounding through the neutral conductor.
•Use UL-listed 4-wire #10 AWG-minimum copper conductor cable.
•Allow at least 5 ft. (1.5 m) length to allow for removal and reinstallation of the dryer.
3.Transfer the dryer’s ground wire from behind the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cable to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cable ground wire to the green ground screw. Tighten aLl screws securely. Reinstall the terminal block access cover.
Four-wire connection for electric dryers: Direct wire
•A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.
•A UL-listed strain relief is required.
1.Remove 5 inches (12.7 cm) of the outer covering from the wire. Remove 5 inches of insulation from the ground wire. Cut off approximately 11⁄ inches (3.8 cm) from the other three wires and strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three shorter wires into a hook shape.
1" (2.5 cm)
Hot |
Neutral |
|
(Black) |
(White) |
|
Ground |
Hot |
|
(Red) |
||
Screw |
||
|
|
White Wire |
|
moved from |
Power Cord |
Ground Screw |
|
|
Ground Wire |
|
Ground Wire
5" (12.7 cm)
2.Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief.
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 4-Wire
Power Cord
Loading...