Colour Television
OWNER’S MANUAL
Please read this manual carefully before operating your set. Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number |
: |
Serial number |
: |
P/NO : MFL42377920-EN (MC059D)
Contents
Installation......................................................... |
2 |
Connection of external equipment.................. |
2 |
Location and function of controls................... |
3 |
Basic operation................................................. |
4 |
Other functions................................................. |
4 |
On screen menus.............................................. |
5 |
Setting up TV stations...................................... |
5 |
Picture adjustment............................................ |
6 |
Time setting....................................................... |
6 |
Troubleshooting check list.............................. |
7 |
Installation
Power
This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.
Press the POWER button on the front panel or side panel to turn off the TV when the TV set is not being used for a long time.It is recommended to remove the plug from the wall outlet(Power point).
Disconnecting device from mains
Mains plug is the disconnecting device. The plug must remain readily operable
Warning
To prevent fire or shock hazard, do not expose the set to rain or moisture.
Do not place anything containing liquid on top of the set, this may cause a fire or could give an electric shock.
Service
Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.
Aerial
Connect the aerial cable to the socket on the back cover. For the best reception an outdoor aerial should be used.
Location
Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.
Connection of external equipment
Aerial socket
1.Connect the RF out socket of the VCR to the aerial socket on the back of the set.
2.Connect the aerial cable to the RF aerial in socket of the VCR.
3.Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ section.
4.Select the programme number where the VCR channel is stored.
5.Press the PLAY button on the VCR.
Audio/Video in/out sockets (option)
1.Connect the audio/video out sockets of the VCR to audio/video in sockets of the set and in sockets of the VCR to out sockets of the
set.
2.If the VCR is connected to the AV sockets on the set, press the TV/AV button to select AV
(or AV1).
3.Press the PLAY button on the VCR.
The VCR playback picture appears on the screen.
ANTENNA
IN
IN
VIDEO AUDIO
VCR
2
Location and function of controls
Remote control handset
1 |
8 |
|
|
2 |
|
3 |
9 |
4 |
|
5 |
10 |
6 |
|
7 |
12 |
11 |
|
selects a favorite programme.
12.I/II/* (option)
selects the language during dual language broadcast.
selects the sound output.
Battery installation
The remote control handset is powered by AAA type batteries. To load the batteries, turn the remote control handset over and open the battery compartment. Install batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.
or
Front panel
-MAIN POWER (ON/OFF) switches the set on or off.
1. |
POWER |
|
|
switches |
or off to |
|
standby. |
|
2. |
NUMBER |
|
|
switches |
or directly |
|
select a |
|
3. |
MENU |
|
4. |
selects a |
|
D / E |
item. |
|
|
selects a |
switches the set on from standby. scans programmes automatically.
F / G (Volume Up/Down) adjusts the volume. adjusts menu settings.
OK
accepts your selection or displays the current mode.
5.Q.VIEW
returns to the previously viewed programme.
6.EYE/* (option)
switches the eye function on or off.
7.SLEEP (option) sets the sleep timer.
8.MUTE
switches the sound on or off.
9.TV/AV
selects TV or AV mode.
switches the set on from standby.
10.LIST
displays the programme table.
11.FAVOURITE (option)
-REMOTE CONTROL SENSOR
Note : Only use the supplied remote control handset. (When you use others, they’ll be not able to function.)
-POWER/STANDBY INDICATOR
illuminates brightly when the set is in standby mode.
dims when the set is switched on.
-MENU
selects a menu.
-OK (option)
accepts your selection or displays the current mode.
F / G (Volume Up/Down)
adjusts the volume. adjusts menu settings.
D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby.
3
Loading...