Supplementary instructions
Supplementary instructions
OPTIBAR 5060
OPTIBAR 5060
OPTIBAR 5060OPTIBAR 5060
Supplementary instructionsSupplementary instructions
Pressure transmitter
Category
ATEX II 1/2G, 2G Ex d ia IIC T6...T1 Ga/Gb, Gb
IECEx Ex d ia IIC T6...T1 Ga/Gb, Gb
Housing
Aluminium, single chamber
Stainless steel (precision casting), single chamber
© KROHNE 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
CONTENTS
OPTIBAR 5060
1 Safety instructions 3
1.1 General notes ................................................................................................................... 3
1.2 EC conformity ................................................................................................................... 3
1.3 Approval according to the IECEx scheme ........................................................................ 4
1.4 Safety instructions............................................................................................................ 4
2 Device description 5
2.1 Device description ............................................................................................................ 5
2.2 Marking............................................................................................................................. 5
2.2.1 Marking for ATEX ....................................................................................................................5
2.2.2 IECEx marking......................................................................................................................... 6
2.3 Flammable products ........................................................................................................ 7
2.4 Equipment category .........................................................................................................7
2.5 Protection types................................................................................................................ 8
2.6 Ambient temperature / temperature classes.................................................................. 9
2.6.1 Temperature derating........................................................................................................... 10
2.7 Electrical data................................................................................................................. 11
3 Installation 12
3.1 Installation...................................................................................................................... 12
4 Further notes 13
4.1 Protection against static electricity ............................................................................... 13
4.2 Use of an overvoltage arrester....................................................................................... 13
4.3 Grounding ....................................................................................................................... 13
4.4 Impact and friction sparks ............................................................................................. 13
4.5 Material resistance......................................................................................................... 13
4.6 Installation / mounting ................................................................................................... 13
4.7 Protection type flameproof enclosure Ex "d" ................................................................ 14
4.8 Mounting of the OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with remote housing........... 15
4.9 Size and type of thread for the "Ex-d" cable entries ..................................................... 15
2
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
1.1 General notes
The pressure-based measuring devices OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are also used
for pressure and level measurement in hazardous areas.
The measured products can also be combustible liquids, gases, mist or vapours.
The OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 consist of an "Ex-d" electronics housing with
integrated electronics module, a process connection element and a sensor, the pressure
measuring cell with optionally connected chemical seal. As an option, the display and
adjustment module can also be mounted.
The OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are suitable for use in hazardous atmospheres of all
combustible materials of explosion group IIA, IIB and IIC for applications requiring category 1/2G
or 2G equipment.
If the OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are installed and operated in hazardous areas, the
general Ex installation regulations EN 60079-14 as well as these safety instructions must be
observed.
SAFETY INSTRUCTIONS 1
The operating instructions as well as the installation regulations and standards that apply for
explosion protection of electrical systems must always be observed.
The installation of explosion-endangered systems must always be carried out by qualified
personnel.
1.2 EC conformity
The manufacturer declares with the EC declaration of conformity on his own responsibility
conformity with the protection goals of directive 94/9/EC acc. to EN 60079-0 and EN 60079-1 and
EN 60079-26 for use in hazardous areas with gas.
The EC type test certificate of the Institut für Sicherheitstechnik GmbH forms the basis of the EC
declaration of conformity:
The "X" after the certificate number refers to special conditions for safe use of the device, which
have been listed in these instructions.
If needed the EC type test certificate can be downloaded from the manufacturer's website.
TÜV 14 ATEX 7517 X
TÜV 14 ATEX 7517 X
TÜV 14 ATEX 7517 XTÜV 14 ATEX 7517 X
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
3
1 SAFETY INSTRUCTIONS
1.3 Approval according to the IECEx scheme
Conformity with IECEx standards was tested in accordance with the IECEx Certification Scheme
for Explosive Atmospheres acc. to IEC 60079-0, IEC 60079-1, IEC 60079-11 and IEC 60079-26.
The number of the IEC certificate is:
IECEx TUR 14.0018 X
IECEx TUR 14.0018 X
IECEx TUR 14.0018 XIECEx TUR 14.0018 X
The "X" after the certificate number refers to special conditions for safe use of the device, which
have been listed in these instructions.
If needed, the IEC certificate can be downloaded from the manufacturer's website.
1.4 Safety instructions
Assembly, installation, start-up and maintenance may only be performed by personnel trained in
explosion protection!
OPTIBAR 5060
CAUTION!
The operator or his agent is responsible for observing any additional standards, directives or
laws if required due to operating conditions or place of installation. This applies in particular to
the use of easily detachable process connections when measuring flammable media.
4
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
2.1 Device description
The pressure transmitter of the OPTIBAR 5060 series is designed to measure the pressure of
vaporous, gaseous and liquid media. The pressure transmitters are supplied as standard with 2wire, 4...20 mA signal outputs.
2.2 Marking
2.2.1 Marking for ATEX
The marking of the entire device is on the housing, where the following identification plate can be
found.
DEVICE DESCRIPTION 2
Figure 2-1: Example for an ATEX nameplate for a OPTIBAR 5060
1 Observe the installation and operating instructions
2 Marking of notified body and CE marking
3 Hardware and Software version
4 Product name and type code
5 Nominal range
Permissible process pressure
6 Permissible temperature range
7 Electronics power supply and signal output
8 Ingress protection and material of wetted parts
(Diaphragm, process connections, gasket and fill fluid)
9 Approvals and approval directive
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
5
2 DEVICE DESCRIPTION
2.2.2 IECEx marking
The marking of the entire device is on the housing, where the following identification plate can be
found.
OPTIBAR 5060
Figure 2-2: Example for an IECEx nameplate for a OPTIBAR 5060
1 Observe the installation and operating instructions
2 Marking of notified body
3 Hardware and Software version
4 Product name and type code
5 Nominal range
Permissible process pressure
6 Permissible temperature range
7 Electronics power supply and signal output
8 Ingress protection and material of wetted parts
(Diaphragm, process connections, gasket and fill fluid)
9 Approvals and approval directive
6
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
2.3 Flammable products
Atmospheric conditions:
Atmospheric conditions:
Atmospheric conditions:Atmospheric conditions:
An explosive atmosphere is a mixture of air and flammable gases, vapours, mists or dusts under
atmospheric conditions. It is defined by the following values
= -20...+60°C / -4...+140°F and P
T
atm
Outside of this range, for most mixtures no key figures are available for the ignition behaviour.
Operating conditions:
Operating conditions:
Operating conditions:Operating conditions:
Outside of atmospheric conditions you cannot apply to the explosion protection according to
directive 94/9/EC (ATEX) – regardless of the zone assignment - due to the lack of key safety data.
2.4 Equipment category
Category 1/2G equipment (EPL-Ga/Gb equipment
Category 1/2G equipment (EPL-Ga/Gb equipment)
Category 1/2G equipment (EPL-Ga/Gb equipmentCategory 1/2G equipment (EPL-Ga/Gb equipment
The process connection element is installed in the separating wall, which separates areas in
which equipment of category 2G or 1G are required. The electronics housing is installed in
hazardous areas requiring equipment of category 2G. The sensor is installed in hazardous areas
requiring equipment of category 1G.
DEVICE DESCRIPTION 2
= 0.8...1.1 bar / 11.6...15.9 psi.
atm
Category 2G equipment (EPL-Ga equipment)
Category 2G equipment (EPL-Ga equipment)
Category 2G equipment (EPL-Ga equipment)Category 2G equipment (EPL-Ga equipment)
The devices are installed in hazardous areas requiring equipment category 2G.
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
7
2 DEVICE DESCRIPTION
2.5 Protection types
The pressure transmitter is designed in protection type flameproof enclosure with internal
intrinsically safe circuits "d ia" according to EN 60079-1/EN 60079-11 and IEC 600791/IEC 60079-11, however the device does NOT
The marking according to ATEX is:
II 1/2G, 2G Ex d ia IIC T6
II 1/2G, 2G Ex d ia IIC T6…T1 Ga/Gb, Gb
II 1/2G, 2G Ex d ia IIC T6II 1/2G, 2G Ex d ia IIC T6
The marking according to IECEx is:
Ex d ia IIC T6...T1 Ga/Gb, Gb
Ex d ia IIC T6...T1 Ga/Gb, Gb
Ex d ia IIC T6...T1 Ga/Gb, GbEx d ia IIC T6...T1 Ga/Gb, Gb
The marking contains the following information:
The marking contains the following information:
The marking contains the following information:The marking contains the following information:
II
II Explosion protection, group II
IIII
GGGG Gas explosion protection
Ex d ia
Ex d ia Flameproof enclosure with internal intrinsically safe circuits "d ia"
Ex d iaEx d ia
IIC
IIC Gas group, suitable for gas groups IIC, IIB and IIA
IICIIC
1/2
1/2 Equipment category 1/2
1/21/2
2222 Equipment category 2
Ga/Gb
Ga/Gb EPL, suitable for zone 0 / zone 1
Ga/GbGa/Gb
Gb
Gb EPL, suitable for zone 1
GbGb
T6...T1
T6...T1 Temperature class, suitable for temperature classes T6 ... T1
T6...T1T6...T1
T1 Ga/Gb, Gb
T1 Ga/Gb, GbT1 Ga/Gb, Gb
NOT require an intrinsically safe supply.
NOTNOT
OPTIBAR 5060
8
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
2.6 Ambient temperature / temperature classes
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with integrated electronics Z (4
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with integrated electronics Z (4 … 20 mA), H
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with integrated electronics Z (4OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with integrated electronics Z (4
(4
(4 … 20 mA/HART) or A (4
20 mA/HART) or A (4 … 20 mA/HART with SIL qualification) or S, T (differential pressure
(4(4
20 mA/HART) or A (420 mA/HART) or A (4
measurement)
measurement)
measurement)measurement)
The max. permissible ambient temperatures depending on the temperature classes are
specified in the following tables.
Category 1/2G equipment
Category 1/2G equipment
Category 1/2G equipmentCategory 1/2G equipment
20 mA/HART with SIL qualification) or S, T (differential pressure
20 mA/HART with SIL qualification) or S, T (differential pressure 20 mA/HART with SIL qualification) or S, T (differential pressure
DEVICE DESCRIPTION 2
20 mA), H
20 mA), H 20 mA), H
Temperature class Ambient temperature range at
the electronics (zone 1)
T6 -50...+60°C / -58...+140°F -20...+23°C / -4...+73.4°F
T5, T4, T3, T2, T1 -50...+60°C / -58...+140°F -20...+60°C / -4...+140°F
For applications requiring equipment category 1/2G, the process pressure of the media must be
between 0.8…1.1 bar. With the stated permissible ambient temperatures, the 80% consideration
of section 6.4.2/EN 1127-1 is taken into account. If OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are
operated at temperatures higher than those specified in the table above, please make sure by
means of appropriate measures that there is no danger of ignition from the hot surface. The
maximum temperature on the electronics/housing should not exceed the values stated in the
table above. The application conditions in areas without hazardous mixtures are specified in the
manufacturer information.
Category 2G equipment
Category 2G equipment
Category 2G equipmentCategory 2G equipment
Temperature class Ambient temperature range at
the electronics
T6 -50...+60°C / -58...+140°F -50...+39°C / -58...+102.2°F
T5 -50...+60°C / -58...+140°F -50...+100°C / -58...+212°F
T4 -50...+50°C / -58...+122°F -50...+135°C / -58...+175°F
T3, T2, T1 -50...+50°C / -58...+122°F -50...+200°C / -58...+392°F
Media temperature range at the
sensor (zone 0)
Media temperature range at the
sensor
If OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are operated at temperatures higher than those
specified in the table above, please make sure by means of appropriate measures, while taking
into consideration the self-heating of 7 K at the sensor, that there is no danger of ignition from
the hot surface. The maximum permissible temperature of the electronics/housing should not
exceed the values given in the table above. The application conditions in areas without hazardous
mixtures are specified in the manufacturer information.
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
9
2 DEVICE DESCRIPTION
2.6.1 Temperature derating
INFORMATION!
Valid for the use as equipment of category 2G or zone 1.
OPTIBAR PC 5060 C (130°C / 266°F)
Figure 2-3: Temperature derating
1 Ambient temperature housing
2 Process temperature
OPTIBAR 5060
OPTIBAR PC 5060 C (150°C / 302°F)
Figure 2-4: Temperature derating
1 Ambient temperature housing
2 Process temperature
10
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
OPTIBAR PM 5060 C
Figure 2-5: Temperature derating
1 Ambient temperature housing
2 Process temperature
3 Process temperature max. 150°C / 302°F
4 Process temperature max. 180°C / 356°F
5 Process temperature max. 200°C / 393°F
DEVICE DESCRIPTION 2
2.7 Electrical data
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with integrated electronics Z (4…20°mA),
H°(4…20°mA/HART) or A (4…20°mA/HART with SIL qualification)
Supply and signal circuit:
(Terminals 1[+], 2[-]
Indicating and adjustment circuits:
(terminals 5, 6, 7, 8)
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with electronics S or T
Supply and signal circuit:
(Terminals 5,6,7,8 in electronics
compartment)
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 version with separate cable outlet
Circuit between sensor unit and
external electronics (terminal 1 - yellow,
terminal 2 - white, terminal 3 - red,
terminal 4 - black)
• U
= 9.6...35 VDC
i
• U
= 253 VAC
m
For connection to the circuit of the appropriate external
display unit in protection type flameproof enclosure "d" or for
connection of an OPTIBAR * 5060 in protection type
flameproof enclosure "Ex d ia" with integrated electronics S
or T as differential pressure measurement.
For connection of an
OPTIBAR * 5060 VGK5/6/D*A/W E with integrated electronics
H, A for differential pressure measurement
in protection type intrinsic safety Ex ia IIC
For the OPTIBAR * 5060 VGK5/6/D*A/W E in the version with
the permanently mounted cable to the measuring sensor unit
and external electronics, the length of the supplied cable
between the external housing and the measuring sensor unit
should not exceed 180 m.
The metallic parts of OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 are electrically connected with the
ground terminals.
The supply and signal circuit is reliably galvanically isolated from parts which can be grounded.
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
11
3 INSTALLATION
3.1 Installation
Installation and setup must be carried out according to the applicable installation standards (e.g.
EN 60079-14 or IEC 60079-14) by qualified personnel trained in explosion protection. The
information given in the manuals and the supplementary instructions must be observed at all
times.
Install pressure transmitters so that:
• there is sufficient overvoltage protection in the event of lightning or overvoltage.
• they are not in a pneumatic flow.
• excessive dust deposits (over 5 mm) and complete dust coverage are prevented.
• there is no danger from mechanical impact effects.
• the device is accessible for any necessary visual inspections and can be viewed from all sides.
• the nameplate is clearly visible.
• it can be operated from a location with secure footing.
CAUTION!
The manufacturer is not liable for any damage resulting from improper use or use other than the
intended purpose. This applies in particular to hazards due to insufficient corrosion resistance
and suitability of the materials in contact with product.
OPTIBAR 5060
12
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
4.1 Protection against static electricity
The OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 in versions with electrostatically chargeable plastic
parts, such as e.g. plastic housing, metal housing with inspection window, with plastic-coated
sensors, suspension cable or suspension hose, distance tube or connection cable with the
remote version, a caution label points out the safety measures that must be taken with regard to
electrostatic charges during operation.
Caution: Plastic part! Risk of electrostatic charge!
• Avoid friction
• No dry cleaning
• Do not mount in areas with flowing, non-conductive products
FURTHER NOTES 4
4.2 Use of an overvoltage arrester
If necessary, a suitable overvoltage arrester can be connected in front of the OPTIBAR * 5060
VGK5/6/D*A/W E/Z/6/7. When used as category 1/2G equipment, as far as necessary analogue, a
suitable overvoltage arrester must be connected in front as protection against voltage surges
according to EN 60079-14 or IEC 60079-14 Chapter 12.3.
4.3 Grounding
In order to avoid the danger of electrostatic charging of the metallic parts, the OPTIBAR * 5060
VGK5/6/D*A/W E/Z/6/7, used as category 1/2G equipment, must be electrostatically connected to
the local equipotential bonding (transfer resistance ≤ 1MΩ), e.g. via the ground terminal.
4.4 Impact and friction sparks
When used as category 1/2G equipment, the OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 in light alloy
(aluminium/titanium) versions must be mounted in such a way that sparks from impact and
friction between light alloy and steel (except stainless steel, if the presence of rust particles can
be excluded) cannot occur.
4.5 Material resistance
With applications requiring 1/2G equipment, the OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 should
only be used in media against which the wetted materials are sufficiently resistant.
4.6 Installation / mounting
The OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 have to be mounted such that the sensor is
effectively secured against touching the vessel wall, under consideration of other vessel
installations and flow conditions in the vessel. This applies especially to suspension pressure
transmitters and versions with distance tube lengths over 3 m.
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
13
4 FURTHER NOTES
4.7 Protection type flameproof enclosure Ex "d"
The terminals for connecting to the operating voltage, i.e. signal circuits, are integrated in the
terminal compartment according to protection type flameproof enclosure "d".
The gaps between housing and cover as well as between threaded fitting and container are
ignition-proof gaps.
The "Ex-d" terminal compartment has an M20 x 1.5 or 1/2-14 NPT thread for the connection of a
certified "conduit" system or for the installation of an "Ex-d" cable entry certified according to
EN 60079-1 or IEC 60079-1. Simple cable entries should not be used. Refer to sections 13.1 and
13.2 of EN 60079-1 or IEC 60079-1. When connecting to a "conduit" system, an appropriate
sealing mechanism must be located directly on the "Ex-d" terminal compartment.
The factory may supply a certified "Ex-d" cable entry. Depending on the type ordered, it may be
suitable for sheathed or unsheathed cable types. The document supplied with the corresponding
cable entry must be observed. The "Ex-d" cable entry must be permanently screwed into the
housing. The supplied cable entry is suitable for the housing temperature range certified for the
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7. If a cable entry other than the one supplied is used, the
other certified cable entry or the temperature classes of the electronics, depending on the
permissible temperature, determines the maximum permitted ambient temperature of the
housing.
OPTIBAR 5060
The screw plug (blind plug) supplied by the factory, depending on the type ordered, is part of the
"Ex-d" housing. If a screw plug other than the one supplied is used, it must be certified according
to EN 60079-1 or IEC 60079-1.
Ensure that before opening the "Ex-d" terminal compartment and when the cover of the
compartment is open (e. g. when connecting or servicing) the supply line is de-energised or that
there is no explosive atmosphere present.
The connecting cable to the "Ex-d" terminal compartment must be fixed and laid so that it is
sufficiently protected against damage. Lay the connecting cable in accordance with EN 60079-14
or IEC 60079-14.
The connecting cables, cable entries and screw plugs or pipeline sealing mechanisms must be
suitable for the lowest ambient temperature.
Prior to start-up, ensure that the cover of the "Ex-d" terminal compartment is screwed in all the
way until it stops. Secure it by unscrewing the locking screw of the cover until it stops.
Unused openings must be sealed according to EN 60079-1 or IEC 60079-1 paragraph 11.9.
The cover of the "Ex-d" terminal compartment has the warning label "Do not open when an
explosive gas atmosphere is present".
14
www.krohne.com 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
OPTIBAR 5060
Single chamber housing with "Ex-d" terminal compartment
Figure 4-1: Single chamber housing with "Ex-d" terminal compartment
1 Thread protection
2 Locking screw of the cover
3 Screw plug
4 Marking of the thread
5 "Ex-d" terminal compartment with electronics module
6 Optionally with inspection window
7 External ground terminal
FURTHER NOTES 4
4.8 Mounting of the OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with remote
housing
With the version with remote housing of the pressure transmitter
OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 the equipotential bonding must be provided in the
complete mounting area of the connection cable between electronics housing and transmitter
housing.
4.9 Size and type of thread for the "Ex-d" cable entries
The "Ex-d" terminal compartment of OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with cable entry
type L, 0, D or 6 has cable entries M20 x 1.5.
The "Ex-d" terminal compartment of OPTIBAR * 5060 VGK5/6/D*A/W E/Z/6/7 with cable entry
type N, 8 or P has cable entries 1/2-14 NPT.
www.krohne.com07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en
15
KROHNE product overview
• Electromagnetic flowmeters
• Variable area flowmeters
• Ultrasonic flowmeters
• Mass flowmeters
• Vortex flowmeters
• Flow controllers
• Level meters
• Temperature assemblies
• Pressure transmitters
• Analysis products
• Products and systems for the oil & gas industry
• Measuring systems for the marine industry
Head Office KROHNE Messtechnik GmbH
Ludwig-Krohne-Str. 5
47058 Duisburg (Germany)
Tel.:+49 203 301 0
Fax:+49 203 301 103 89
info@krohne.com
© KROHNE 07/2014 - 4003592001 - AD OPTIBAR 5060 Exd ia R01en - Subject to change without notice.
The current list of all KROHNE contacts and addresses can be found at:
www.krohne.com
Loading...