Kenwood DPX-U5140 Manual

DPX-U5140

DUAL DIN SIZED CD RECEIVER

INSTRUCTION MANUAL

© 2014 JVC KENWOOD Corporation				B5A-0341-10 (MN)

CONTENTS

	BEFORE USE	2
	BASICS	3
	GETTING STARTED	4
	RADIO	5
	CD / USB / iPod / ANDROID	7
	AUX	9
	Pandora®	10
	AUDIO SETTINGS	11
	DISPLAY SETTINGS	12
	TROUBLESHOOTING	12
	MORE INFORMATION	14
	SPECIFICATIONS	15
	INSTALLATION /
	CONNECTION	16

How to read this manual

•Operations are explained mainly using buttons on the faceplate.

•[XX] indicates the selected items.

•( XX) indicates references are available on the stated page.

BEFORE USE

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

•Adjust the volume so that you can hear sounds outside the car to prevent accidents.

•Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

•Avoid using the external device if it might hinder safe driving.

•Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

•Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

•If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

Remote control (RC-406):

•Do not leave the remote control in hot places such as on the dashboard.

•The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

•The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

•Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Handling discs:

•Do not touch the recording surface of the disc.

•Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

•Do not use any accessories for the disc.

•Clean from the center of the disc and move outward.

•Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

•When removing discs from this unit, pull them out horizontally.

•Remove burrs from the center hole and disc edge before inserting a disc.

2

BASICS

Faceplate	Remote control (RC-406)
Loading slot	Display window
	Remote sensor (Do not
	expose to bright sunlight.)

				Pull out the
				insulation sheet
				when using for
				the first time.
				* Not used
				How to replace the battery
	Volume knob		Reset button
	(turn/press)		• Your preset adjustments will
			also be erased.
To	On the faceplate			On the remote control
Turn on the power	Press	.		Press and hold SRC to turn off the power.
	• Press and hold to turn off the power.			( Pressing SRC does not turn on the power. )

Adjust the volume

Turn the volume knob.

Press

or

.

Press the volume knob during playback to attenuate the sound.

• Press again to cancel.

Press ATT during playback to attenuate the sound.

• Press again to cancel.

	Select a source	Press	repeatedly.					Press SRC repeatedly.
	Change the display	Press					repeatedly.	( not available )
	information	• Press and hold to scroll the current display information.

ENGLISH 3

GETTING STARTED

1Cancel the demonstration

When you turn on the power (or after you reset the unit), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”

1Press the volume knob.

[YES] is selected for the initial setup.

2Press the volume knob again.

“DEMO OFF” appears.

2Set the clock

1 Press FNC to enter [FUNCTION].

2 Turn the volume knob to select [CLOCK], then press the knob.

3 Turn the volume knob to select [CLOCK ADJUST], then press the knob.

4Turn the volume knob to make the settings, then press the knob.

Day Hour Minute

5 Turn the volume knob to select [CLOCK FORMAT], then press the knob. 6 Turn the volume knob to select [12H] or [24H], then press the knob. 7 Press and hold to exit.

To return to the previous setting item, press .

3Set the initial settings

1 Press repeatedly to enter STANDBY.

2Press FNC to enter [FUNCTION].

• Pressing AUDIO enter [AUDIO CONTROL] directly.

3Turn the volume knob to make a selection (see the following table), then press the knob.

4 Repeat step 3 until the desired item is selected or activated. 5 Press and hold to exit.

To return to the previous setting item, press .

		Default: XX
AUDIO CONTROL
	SWITCH	REAR/ SUBWOOFER: Selects whether rear speakers or a subwoofer are
	PREOUT	connected to the line out terminals on the rear (through an external
		amplifier).
	SP SELECT	OFF/ 5/4/ 6 × 9/6/ OEM: Selects according to the speaker size (5 inches
		or 4 inches, 6×9 inches or 6 inches) or OEM speakers for optimum
		performance.
DISPLAY
	EASY MENU	ON: Both display and button illumination change to white color when
		entering [FUNCTION]. ; OFF: Both display and button illumination
		remain as [COLOR SELECT] color. ( 12)
TUNER SETTING
	PRESET TYPE	NORMAL: Memorizes one station for each preset button in each band
		(FM1/ FM2/ FM3/ MW/ SW1/ SW2). ; MIX: Memorizes one station for
		each preset button, regardless of the selected band.

4

GETTING STARTED

RADIO

SYSTEM

	KEY BEEP			ON: Activates the keypress tone. ;
				OFF: Deactivates.
	SOURCE SELECT
		PANDORA SRC		ON: Enables PANDORA in source selection. ;
				OFF: Disables. ( 10)
		BUILT-IN AUX		ON: Enables AUX in source selection. ;
				OFF: Disables. ( 9)
	CD READ			1: Automatically distinguishes between audio file
				disc and music CD. ; 2: Forces to play as a music
				CD. No sound can be heard if an audio file disc
				is played.
	F/W UPDATE
		UPDATE SYSTEM
			F/W UP xx.xx	YES: Starts upgrading the firmware. ; NO: Cancels
				(upgrading is not activated).
				For details on how to update the firmware, see:
				www.kenwood.com/cs/ce/
CLOCK
	CLOCK DISPLAY			ON: The clock time is shown on the display even
				when the unit is turned off. ; OFF: Cancels.

Search for a station

1 Press repeatedly to select TUNER.

2Press repeatedly (or press / on RC-406) to select FM1/ FM2/ FM3/ AM/ SW1/ SW2.

3Press S/ T(or press S/ on RC-406) to search for a station.

•To change the searching method for S/ T: Press and holdrepeatedly.

AUTO1 : Automatically search for a station. AUTO2 : Search for a preset station. MANUAL : Manually search for a station.

•To store a station: Press and hold one of the number buttons (1 to 6).

•To select a stored station: Press one of the number buttons (1 to 6) (or press one of the number buttons (1 to 6) on RC-406).

Direct Access Tuning (using RC-406)

1Press DIRECT to enter Direct Access Tuning.

“– – – • –” (for FM), “– – – –” (for AM/ SW1) or “– – – – –” (for SW2) appears on the display.

2 Press the number buttons to enter a frequency.

3Press to search for a station.

•To cancel, press or DIRECT.

•If no operation is done for 10 seconds after step 2, Direct Access Tuning is automatically canceled.

ENGLISH 5

RADIO

Other settings

1 Press FNC to enter [FUNCTION].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default: XX

TUNER SETTING

LOCAL SEEK* ON: Searches only stations with good reception. ; OFF: Cancels.

•Settings made are applicable only to the selected source/station. Once you change the source/station, you need to make the settings again.

AUTO	YES: Automatically starts memorizing 6 stations with good reception. ; NO: Cancels.
MEMORY	• Selectable only if [NORMAL] is selected for [PRESET TYPE]. ( 4)
MONO SET	ON: Improves the FM reception, but the stereo effect may be lost. ; OFF: Cancels.
NEWS SET	ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels.
REGIONAL	ON: Switches to another station only in the specific region using the “AF” control. ;
	OFF: Cancels.
AF SET	ON: Automatically searches for another station broadcasting the same program in the
	same Radio Data System network with better reception when the current reception is
	poor. ; OFF: Cancels.
TI	ON: Allows the unit to temporarily switch to Traffic Information if available (“TI” lights
	up). ; OFF: Cancels.
PTY SEARCH	Press the volume knob to enter PTY language selection. Turn the volume knob to
	select the PTY language (ENGLISH/ FRENCH/ GERMAN), then press the knob.
	Selects the available Program Type (see the following), then, press S / T to
	start.

CLOCK

TIME SYNC	ON: Synchronizes the unit’s time to the Radio Data System
	station time. ; OFF: Cancels.

* Only for AM/ SW1/ SW2 source.

•[MONO SET]/ [NEWS SET]/ [REGIONAL/ [AF SET]/ [TI]/ [PTY SEARCH] is selectable only when the band is FM1/ FM2/ FM3.

•Available Program Type:

SPEECH : NEWS, AFFAIRS, INFO (information), SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE,

DOCUMENT

MUSIC : POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music)

The unit will search for the Program Type categorized under [SPEECH] or [MUSIC] if selected.

•If the volume is adjusted during reception of traffic information, alarm or news bulletin, the adjusted volume is memorized automatically. It will be applied the next time traffic information, alarm or news bulletin is turned on.

6

CD / USB / iPod / ANDROID

Start playback

The source changes automatically and playback starts.

	Label side			M Eject disc

USB input terminal

USB

CA-U1EX (max.: 500 mA) (optional accessory)

iPod/iPhone

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

ANDROID*3

Micro USB 2.0 cable*2 (commercially available)

*1
	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.

To	On the faceplate				On the remote control
Playback / pause	Press .				Press		.
Reverse /	Press and hold S / T.				Press and hold S /			.
Fast-forward*4
Select a track/file	Press S / T.				Press S /		.
Select a folder*5	Press J / K.				Press	/	.
Repeat play*6	Press	repeatedly.
	TRACK REPEAT/ REPEAT OFF				: Audio CD
	FILE REPEAT/ FOLDER REPEAT/ REPEAT OFF : MP3/WMA/WAV file, iPod or
					ANDROID
	FILE REPEAT/ REPEAT OFF				: KME Light/ KMC file*7
Random play*6	Press	repeatedly.
	DISC RANDOM/ RANDOM OFF			: Audio CD
	FOLDER RANDOM/ RANDOM OFF : MP3/WMA/WAV file, KME Light/ KMC
				file, iPod or ANDROID
	Press and hold		to select ALL RANDOM.*8

ENGLISH 7

CD / USB / iPod / ANDROID

To		On the faceplate
Select control		While in iPod source, press			repeatedly.
mode		MODE ON : Control from the iPod*9
		MODE OFF : Control from the unit
		While in ANDROID source,
		(	9, [ANDROID SETUP])
Select music		Press		repeatedly.
drive		The stored songs in the following start playback.
(	9, [MUSIC	• Selected internal or external memory of a
DRIVE])			smartphone (Mass Storage Class).
		•	Selected drive of a multiple drives device.
*3	When connecting an Android device, “Press [VIEW] to install KENWOOD MUSIC PLAY APP”
	is shown. Follow the instructions to install the application. You can also install the latest
	version of KENWOOD MUSIC PLAY application on your Android device before connecting.
*4	( 14)
	For ANDROID: Applicable only when [BROWSE MODE] is selected. (				9, [ANDROID
*5	SETUP])
	For CD: Only for MP3/WMA files. This does not work for iPod/ ANDROID.
*6	For iPod/ ANDROID: Applicable only when [MODE OFF]/ [BROWSE MODE] is selected.
*7	KME Light : KENWOOD Music Editor Light, KMC : KENWOOD Music Control ( 14)
*8	For CD: Only for MP3/WMA files.
*9	You can still play/pause, file skip, fast-forward or reverse files from the unit.

Select a file from a folder/list

1	Press		.
2	Turn the volume knob to select a folder/list, then press the knob.
3	Turn the volume knob to select a file, then press the knob.
	Quick Search
	If you have many files, you can search through them quickly.
	For USB (for KME Light/ KMC files):
	Press S / T to search at a preset skip search ratio.
	(	9, [SKIP SEARCH])
	Press and hold S / T to search at a 10% ratio.
	•	Not applicable for CD and MP3/WMA/WAV files.

For iPod:

You can search for a file according to the first character.

Turn the volume knob quickly to enter character search. Turn the volume knob to select the character.

•To search for a character other than A to Z and 0 to 9, enter only “*”.

•Press and hold J / K changes the characters rapidly.

Press S / T to move to the entry position.

• You can enter up to 3 characters.

Press the volume knob to start searching.

•To return to the root folder/ first file/ top menu, press .

•To return to the previous setting item, press .

•To cancel, press and hold .

•For iPod, applicable only when [MODE OFF] is selected. ( Select control mode)

•For ANDROID, applicable only when [BROWSE MODE] is selected. ( 9, [ANDROID SETUP])

8

CD / USB / iPod / ANDROID

Direct Music Search (using RC-406)

1 Press DIRECT.

2 Press the number buttons to enter a track/file number. 3 Press to search for music.

•To cancel, press or DIRECT.

•Not available if Random Play is selected.

•Not applicable for iPod, ANDROID, KME Light/ KMC file.

Listen to TuneIn Radio/ TuneIn Radio Pro/ Aupeo

While listening to TuneIn Radio, TuneIn Radio Pro or Aupeo, connect the iPod/ iPhone to the USB input terminal of the unit.

• The unit will output the sound from these applications.

Other settings

1 Press FNC to enter [FUNCTION].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press and hold to exit.

To return to the previous setting item, press .

Default: XX

ANDROID SETUP

BROWSE MODE: Control from the unit (using KENWOOD MUSIC PLAY application). ;

HAND MODE: Control other media player applications from the Android device (without using KENWOOD MUSIC PLAY application). However, you can still play/pause and file skip from the unit.

USB

	MUSIC DRIVE	DRIVE CHANGE: The next drive ([DRIVE 1] to [DRIVE 5]) is selected automatically and
		playback starts.
		Repeat steps 1 to 3 to select the following drives.
	SKIP SEARCH	0.5%/ 1%/ 5%/ 10%: While listening to iPod, ANDROID or KME Light/ KMC file, selects
		the skip search ratio over the total files.

AUX

Preparation:

Select [ON] for [BUILT-IN AUX]. ( 5)

Start listening

1 Connect a portable audio player (commercially available).

Auxiliary input jack	Portable audio player

3.5 mm stereo mini plug with “L” shaped connector (commercially available)

2 Press repeatedly to select AUX.

3 Turn on the portable audio player and start playback.

Set the AUX name

While listening to a portable audio player connected to the unit...

1 Press FNC to enter [FUNCTION].

2Turn the volume knob to select [SYSTEM], then press the knob.

3Turn the volume knob to select [AUX NAME SET], then press the knob.

4Turn the volume knob to make a selection, then press the knob.

AUX (default)/ DVD/ PORTABLE/ GAME/ VIDEO/ TV

5 Press and hold to exit.

To return to the previous setting item, press .

ENGLISH 9

Pandora®

Preparation:

Install the latest version of the Pandora application on your device (iPhone/ iPod touch), then create an account and log in to Pandora.

• Select [ON] for [PANDORA SRC]. ( 5)

Start listening

1 Open the Pandora application on your device.

2Connect your device to the USB input terminal.

USB input terminal

KCA-iP102 / KCA-iP103 (optional accessory)*1 or accessory cable of the iPod/iPhone*2

The source changes to PANDORA and broadcast starts.

To		On the faceplate		On the remote control
Playback / pause		Press	.	Press	.
Skip a track		Press T.		Press	.
Thumbs up or thumbs		Press	/ .	Press	/	.
down*3
*1	KCA-iP102 : 30-pin type, KCA-iP103 : Lightning type
*2	Do not leave the cable inside the car when not using.
*3	If thumbs down is selected, the current track is skipped.

Create and save a new station

1 Press and hold FNC.

2Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.

A new station is created based on the current song or artist.

3 Press and hold one of the number buttons (3 to 6) to store.

To select a stored station, press one of the number buttons (3 to 6).

Search for a registered station

1 Press

.

2Turn the volume knob to make a selection, then press the knob.

[BY DATE]: According to the registered date [A-Z]: Alphabetical order

3 Turn the volume knob to the desired station, then press the knob.

To cancel, press and hold . (or using RC-406)

Press J/ K to search for a station, then press .

Bookmark a song or artist information

1 Press and hold.

2Turn the volume knob to make a selection, then press the knob.

[THIS TRACK]: Current song information [THIS ARTIST]: Current artist information

“BOOKMARKED” appears and the information is stored to your device. The bookmark is available on your Pandora account but not on this unit.

10

AUDIO SETTINGS

While listening to any source...

1 Press AUDIO to enter [AUDIO CONTROL].

2Turn the volume knob to make a selection (see the following table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated.

4Press and hold to exit.

(or using RC-406)

1 Press AUD to enter [AUDIO CONTROL].

2 Press J/ K to make a selection, then press .

To return to the previous setting item, press .

				Default: XX
	SUB-W LEVEL		–15 to +15 (0)	Adjusts the subwoofer output level.
	BASS LEVEL		–8 to +8 (+6)	Adjusts the level to memorize for each source. (Before
	MID LEVEL		–8 to +8 (+5)
				making an adjustment, select the source you want to
				adjust.)
	TRE LEVEL		–8 to +8 (0)
	EQ PRO
		BASS ADJUST	BASS CTR FRQ	60HZ/ 80HZ/ 100HZ/ 200HZ: Selects the center frequency.
			BASS LEVEL	–8 to +8 (+6): Adjusts the level.
			BASS Q FACTOR	1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
			BASS EXTEND	ON: Turns on the extended bass. ; OFF: Cancels.
		MID ADJUST	MID CTR FRQ	0.5KHZ/ 1.0KHZ/ 1.5KHZ/ 2.5KHZ: Selects the center
				frequency.
			MID LEVEL	–8 to +8 (+5): Adjusts the level.
			MID Q FACTOR	0.75/ 1.00/ 1.25: Adjusts the quality factor.
		TRE ADJUST	TRE CTR FRQ	10.0KHZ/ 12.5KHZ/ 15.0KHZ/ 17.5KHZ: Selects the
				center frequency.
			TRE LEVEL	–8 to +8 (0): Adjusts the level.

PRESET EQ	DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
	NATURAL/ USER: Selects a preset equalizer suitable to the music
	genre. (Select [USER] to use the customized settings.)
	[DRIVE EQ] is a preset equalizer that reduces noise outside the car
	or running noise of the tyres.
BASS BOOST	LEVEL1/ LEVEL2/ LEVEL3: Selects your preferred bass boost
	level. ; OFF: Cancels.
LOUDNESS	LEVEL1/ LEVEL2: Selects your preferred low and high frequencies
	boost to produce a well-balanced sound at a low volume level. ;
	OFF: Cancels.
SUBWOOFER SET	ON: Turns on the subwoofer output. ; OFF: Cancels.
LPF SUBWOOFER	THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
	160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
	160 Hz are sent to the subwoofer.
SUB-W PHASE	REVERSE (180°)/ NORMAL (0°): Selects the phase of the
	subwoofer output to be in line with the speaker output for
	optimum performance. (Selectable only if a setting other than
	[THROUGH] is selected for [LPF SUBWOOFER].)
FADER	R15 to F15 (0): Adjusts the rear and front speaker output balance.
BALANCE	L15 to R15 (0): Adjusts the left and right speaker output balance.
VOLUME OFFSET	For AUX: –8 to +8 (0) ; For other sources: –8 to 0: Presets the
	volume adjustment level of each source. (Before adjustment,
	select the source you want to adjust.)
SOUND RECNSTR	ON: Creates realistic sound by compensating the high-frequency
(Sound	components and restoring the rise-time of the waveform that are
reconstruction)	lost in audio data compression. ; OFF: Cancels.

•[SUB-W LEVEL]/ [SUBWOOFER SET]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if [SWITCH PREOUT] is set to [SUBWOOFER]. ( 4)

•[SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].

ENGLISH 11