
INSTALLATION INSTRUCTIONS
KBRF-300
RFI (EMI) FILTER – KB P/N 9484A
Approved (EN55011)
See Safety Warning on Page 1
A COMPLETE LINE OF MOTOR DRIVES
© 2002 KB Electronics, Inc.
!
TM

2
ii. SAFETY WARNING! Please read carefully
This product should be installed and serviced by a qualified technician, electrician, or electrical
maintenance person familiar with its operation and the hazards involved. Proper installation, which
includes wiring, mounting in proper enclosure, fusing or other over current protection, and grounding
can reduce the chance of electrical shocks, fires, or explosion in this product or products used with
this product, such as electric motors, switches, coils, solenoids, and/or relays. Eye protection must
be worn and insulated adjustment tools must be used when working with control under power. This
product is constructed of materials (plastics, metals, carbon, silicon, etc.) which may be a potential
hazard. Proper shielding, grounding and filtering of this product can reduce the emission of radio frequency interference (RFI) which may adversely affect sensitive electronic equipment. If further information is required on this product, contact the Sales Department. It is the responsibility of the equipment manufacturer and individual installer to supply this Safety Warning to the ultimate end user of
this product. (SW effective 9/2000).

3
I. APPLICATION NOTE
This product is intended to be used with electronic motor speed controls containing the “CE” mark
and manufactured by KB Electronics, Inc., Coral Springs, FL 33065 USA. When installed in accordance with the procedures outlined, the motor speed control will comply with “CE” Council Directive
89/336/EEC relating to EMC.
II. RATINGS
16 Amps AC Maximum – 115/230 VAC – 50/60 Hz
Temperature Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 – 50 ºC
Frequency Range . . . . . . . . . . . . . . . . . . . . . . 150 kHz – 30 MHz Per CE Specification EN55011
Earth Leakage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 mA @ 250 VAC/50 Hz
This product complies with all CE directives pertinent at the time of manufacture. Contact the
Sales Department for detailed installation and Declaration of Conformity.

4
FIGURE 1 – MECHANICAL SPECIFICATIONS – INCHES / [mm]
2.30
[58.4]
1.38
[35.0]
1.78
[45.3]
5.30
[134.6]
6.00
[152.4]
6.40
[162.5]
1.31
[33.3]
0.75
[19.1]

5
FIGURE 2 – WIRING DIAGRAM

III. MOUNTING
Mount the KBRF-300 on a flat surface using the two (2) mounting tabs. (See figure 1, on page 4.)
Be sure unit is not exposed to environmental conditions which will adversely affect its operation
such as water, excessive temperature or metal chips.
IV. WIRING (See figure 2 on page 5)
a) Wire KBRF-300 Filter to control using 1/4” - QD terminals. Wires should be as short as possi-
ble and may have to be shielded with the shield grounded (earthed) at both ends.
b) Wire AC line to filter using 1/4” - QD terminals. Shielded wiring is normally
not necessary for
the AC line. Be sure to connect ground wire to 4 mm ground stud (Earth) on KBRF-300 Filter.
V. RFI/EMI CONSIDERATIONS
a) It may be necessary to shield the motor speed control or mount it in a metal enclosure to
reduce radiated EMI.
6

7
b) It is the responsibility of the system integrator to provide a finished machine that will conform to
all RFI/EMI requirements. Installing the control in the way shown above, along with other CE
approved guidelines, the control should not emit undesirable levels of RFI/EMI. These instructions do not guarantee that your system will meet all requirements for council Directive
89/336/EEC relating to EMC. A Declaration of Conformity is available upon request.

VI. LIMITED WARRANTY
For a period of 18 months from the date of original purchase, KB Electronics, Inc. will repair or replace, without charge, devices which our examination proves to be defective in material or workmanship. This warranty is valid if the unit has not been tampered with by unauthorized persons, misused, abused, or improperly
installed and has been used in accordance with the instructions and/or ratings supplied. The foregoing is in
lieu of any other warranty or guarantee, expressed or implied. KB Electronics, Inc. is not responsible for any
expense, including installation and removal, inconvenience, or consequential damage, including injury to any
person, caused by items of our manufacture or sale. Some states do not allow certain exclusions or limitations found in this warranty and therefore they may not apply to you. In any event, the total liability of KB
Electronics, Inc., under any circumstance, shall not exceed the full purchase price of this product. (rev 2/2000)
KB Electronics, Inc.
12095 NW 39th Street, Coral Springs, FL 33065-2516 • (954) 346-4900 • Fax (954) 346-3377
Outside Florida Call TOLL FREE (800) 221-6570 • E-mail – info@kbelectronics.com
www.kbelectronics.com
(A40267) – Rev. C – 3/2002