JVC RX-7012R, RX-7010R Manual

AUDIO/VIDEO CONTROL RECEIVER

RX-7010RBK / RX-7012RSL

CATV/DBS

VCR

TV

AUDIO

DVD

DVD MUILTI

CD

FM/AM

TV/DBS

VCR

TAPE/CDR

PHONO

− BASS +

−TREBLE +

SURROUND

DSP ANALOG/DIGITAL

SLEEP

ON/OFF

MODE

INPUT

BASSBOOST

EFFECT

+ CENTER –

1

2

3

MENU

TEST

+ REAR•L –

4

5

6

SOUND

ENTER

AUDIO/VIDEO CONTROL RECEIVER

– REAR•R +

7/P

8

9

FM/AM TUNING

FM/AM PRESET

FM MODE

EON

PTY SEARCH TA/NEWS/INFO DISPLAY MODE

MUTING

–SUBWOOFER+

COMPULINK

10

0

+10

STANDBY

Remote

RETURN

FMMODE

100+

MEMORY

MASTER VOLUME

CATV/DBS

CONTROL

+

+

+

STANDBY/ON

CH

TV VOL

VOLUME

D I G I T A L

TV/VIDEO

−

−

−

PLAY

SURROUND ON/OFF

INPUT

+

ANALOG/DIGITAL

BASS BOOST

ADJUST

SETTING

INPUT ATT

DVD MULTI

DVD

VCR

TV SOUND/DBS

/REW

FF/

TUNING

PAUSE

SOURCE NAME

−

DSP MODE

CONTROL

SPEAKERS ON/OFF

DOWN

UP

REC

PTY– PTY SEARCH

PTY+

1

2

PHONO

CD

TAPE/CDR

FM/AM

PAUSE

SOURCE NAME

STOP CONTROL

DISPLAY

PHONES

RM-SRX7010R

A/V CONTROL RECEIVER

D I G I T A L

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.

Serial No.

LVT0579-005A

[B]

Warnings, Cautions and Others

IMPORTANT for the U.K.

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with an identical approved type, as originally fitted.

If nonetheless the mains plug is cut off ensure to remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not supplied fitted with a mains plug then follow the instructions given below:

IMPORTANT.

DO NOT make any connection to the terminal which is marked with the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wires in the mains lead on this product are coloured in accordance with the following code:

Blue : Neutral

Brown : Live

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1.Do not remove screws, covers or cabinet.

2.Do not expose this appliance to rain or moisture.

Caution –– switch!

Disconnect the mains plug to shut the power off completely. The switch in any position does not disconnect the mains line. The power can be remote controlled.

CAUTION

•Do not block the ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

•Do not place any naked flame sources, such as lighted candles, on the apparatus.

•When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

•Do not use this apparatus in a bathroom or places with water. Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this apparatus.

G-1

SAFETY INSTRUCTIONS

“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”

This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

Do read the operating instructions before you attempt to use the equipment.

Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.

Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.

Do be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw the mains plug and consult your dealer.

DON’T remove any fixed cover as this may expose dangerous voltages.

DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode.

Switch off using the switch on the equipment and make sure that your family know how to do this.

Special arrangements may need to be made for infirm or handicapped people.

DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.

DON’T listen to headphones at high volume as such use can permanently damage your hearing.

DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.

Overheating will cause damage and shorten the life of the equipment.

DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions.

DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL

—NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal electrical shock.;

—NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!

Caution: Proper Ventilation

To avoid risk of electric shock and fire and to protect from damage.

Locate the apparatus as follows:

Front:	No obstructions open spacing.
Sides:	No obstructions in 10 cm from the sides.
Top:	No obstructions in 10 cm from the top.
Back:	No obstructions in 15 cm from the back
Bottom:	No obstructions, place on the level surface.

In addition, maintain the best possible air circulation as illustrated.

Spacing 15 cm or more

Front

Wall or obstructions

RX-7010RBK/

RX-7012RSL

Stand height 15 cm or more

Floor

G-2

Table of Contents
Parts Identification ......................................	2
Getting Started...........................................	3
Before Installation ......................................................................	3
Checking the Supplied Accessories ...........................................	3
Connecting the FM and AM (MW/LW) Antennas .....................	3
Connecting the Speakers ............................................................	4
Connecting Audio/Video Components .......................................	5
Connecting the Power Cord .......................................................	9
Putting Batteries in the Remote Control ....................................	9
Basic Operations .......................................	10
Turning the Power On and Off (Standby) ................................	10
Selecting the Source to Play .....................................................	10
Adjusting the Volume ...............................................................	11
Selecting the Front Speakers ....................................................	11
Muting the Sound .....................................................................	12
Reinforcing the Bass ................................................................	12
Adjusting the Tone ...................................................................	12
Attenuating the Input Signal ....................................................	12
Adjusting the Subwoofer Output Level ....................................	12
Basic Settings...........................................	13
Recording a Source ..................................................................	13
Adjusting the Front Speaker Output Balance ...........................	13
Changing the Source Name ......................................................	13
Setting the Subwoofer Information ..........................................	14
Setting the Speakers for the DSP Modes .................................	14
Digital Input (DIGITAL IN) Terminal Setting .........................	16
Selecting the Analog or Digital Input Mode ............................	16
Storing the Basic Settings and Adjustments .............................	17
Using the Sleep Timer ..............................................................	17
Receiving Radio Broadcasts ........................	18
Tuning in Stations Manually ....................................................	18
Using Preset Tuning .................................................................	18
Selecting the FM Reception Mode ...........................................	19
Using the RDS (Radio Data System) to Receive FM Stations . 20
Searching for a Program by PTY Codes ..................................	20
Switching to a Broadcast Program of
Your Choice Temporarily ...................................................	21
Using the DSP Modes ................................	23
What are the DSP Modes? ........................................................	23
Reproducing the Sound Field ....................................................	24
Available DSP Modes According to the Speaker Arrangement ..	25
Adjusting the Surround Modes ................................................	26
Adjusting the DAP Modes .......................................................	28
Activating the DSP Modes .......................................................	29

Using the DVD MULTI Playback Mode ..........	30
Activating the DVD MULTI Playback Mode ..........................	30
COMPU LINK Remote Control System .........	31
Operating JVC’s Audio/Video Components ...	32
Operating Audio Components ..................................................	32
Operating Video Components ..................................................	34
Operating Other Manufacturers’ Video
Equipment ............................................	35
Troubleshooting .........................................	39
Specifications............................................	40

1

Parts Identification

Become familiar with the buttons and controls on the receiver before use.

Refer to the pages in parentheses for details.

1

2

3

4 5

6

7

8

AUDIO/VIDEO CONTROL RECEIVER

FM/AM TUNING

FM/AM PRESET

FM MODE

EON

PTY SEARCH

TA/NEWS/INFO DISPLAY MODE

COMPULINK

Remote

STANDBY

MEMORY

MASTER VOLUME

STANDBY/ON

D I G I T A L

S U R R O U N D

D I G I T A L

SURROUND ON/OFF

INPUT

ANALOG/DIGITAL

BASS BOOST

ADJUST SETTING

DVD MULTI

DVD

VCR

TV SOUND/DBS

INPUT ATT

SOURCE NAME

DSP MODE

CONTROL

SPEAKERS ON/OFF

DOWN

UP

1

2

PHONO

CD

TAPE/CDR

FM/AM

SOURCE NAME

PHONES

9 p q w e r

t y u i o ;

Remote Control

Front Panel

1 a

2	CATV/DBS	VCR		TV		AUDIO
	DVD	DVD MUILTI		CD		FM/AM
3	TV/DBS	VCR		TAPE/CDR		PHONO
4	− BASS +			−TREBLE+
5	SURROUND	DSP	ANALOG/DIGITAL			SLEEP
	ON/OFF	MODE		INPUT
6	BASSBOOST	EFFECT		– CENTER+
7		1		2		3
				MENU
		TEST		– REAR• L+
		4		5		6
				ENTER
8	SOUND			– REAR• R+
		7/P		8		9
9	MUTING			–SUBWOOFER+
		10		0		+10
		RETURN		FMMODE		100+
	CATV/DBS	+		+		+
p	CONTROL
q		CH		TV VOL		VOLUME
	TV/VIDEO	−		−		−
w	+			PLAY
e		/REW		PAUSE		FF/
	TUNING
	−		PTY SEARCH
	REC	PTY–				PTY+
r	PAUSE
				STOP	CONTROL
				DISPLAY

RM-SRX7010R

A/V CONTROL RECEIVER

	1	Display window (See below) *		1	STANDBY/ON			button and STANDBY
		a: Remote control operation mode indicator			lamp (10)
		b: Signal transmission indicator		2	FM/AM TUNING 5/ buttons (18)
b			Lights up when transmitting the remote	3	FM/AM PRESET 5/ buttons (18)
			control signal.	4	FM MODE button (19)
	2		buttons (10, 34 – 38)	5	MEMORY button (18)
		CATV/DBS, VCR, TV, AUDIO		6	Display (10)
	3	Source selecting buttons (10, 17) *		7	Remote sensor (9)
		DVD, DVD MULTI, CD, FM/AM,TV/DBS,VCR,		8	RDS operation buttons (20 – 21)
		TAPE/CDR, PHONO			EON, PTY SEARCH, TA/NEWS/INFO,
t 4 BASS +/– buttons (12)					DISPLAY MODE
y 5 SURROUND ON/OFF button (26, 29)				9	PHONES jack (11)
u 6 DSP MODE button (27 – 29)				p SURROUND ON/OFF button (26, 29)
	7	BASS BOOST button (12)		q DSP MODE button (27 – 29)
	8	SOUND button (12, 26 – 28, 30) *		w INPUT ANALOG/DIGITAL button (17)
i 9 MUTING button (12)					INPUT ATT button (12)
	p CATV/DBS CONTROL button (36) *			e SPEAKERS ON/OFF 1 button (11)
o	q TV/VIDEO button (34, 35)				SPEAKERS ON/OFF 2 button (11)
	w CH(annel) +/– buttons (34 – 37)			r BASS BOOST button (12)
;	e TUNING +/– buttons (18)			t Source selecting buttons (10, 16)
	r REC PAUSE button (33, 34, 37)				DVD MULTI, DVD, VCR, TV SOUND/DBS,
	t TREBLE +/– buttons (12)				PHONO, CD, TAPE/CDR, FM/AM
	y SLEEP button (17)			y SOURCE NAME buttons (13)
a u ANALOG/DIGITAL INPUT button (17)					• The TV SOUND/DBS button and TAPE/CDR
	i • 10 keys for selecting preset channels (19)
s					button also function as the SOURCE NAME
		• 10 keys for adjusting sound (12, 19, 26 – 28, 30)
					button.
		• 10 keys for operating audio/video components
				u ADJUST button (12, 13, 26 – 28, 30)
		(32 – 38)		i CONTROL UP 5/DOWN buttons
	o TV VOL(ume) +/– buttons (34, 35)			o SETTING button (14 – 16)

	; VOLUME +/– buttons (11)	; MASTER VOLUME control (11)
	a • RDS operation buttons (20 – 21)
	PTY SEARCH, PTY +/–, DISPLAY
	• Operating buttons for audio/video components
	(32 – 34, 37, 38)
	s CONTROL button (33, 34) *

*When you press one of these buttons, the remote control operation mode appears on the display window for about 10 seconds.

Ex.: When you press CD button

Buttons on the Remote Control	Remote Control Operation Mode
FM/AM	TUNER
CD	CD
PHONO	PHONO
TAPE/CDR	TAPE
DVD	DVD
DVD MULTI	DVD

Buttons on the Remote Control	Remote Control Operation Mode
TV/DBS	TV
VCR	VCR
CATV/DBS CONTROL	DBS
CONTROL	Current setting or VCR or TAPE
	or CDDSC
SOUND	SOUND

2

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM (MW/LW) Loop Antenna (1)

•FM Antenna (1)

If anything is missing, contact your dealer immediately.

Connecting the FM and AM (MW/LW)

Antennas

FM Antenna Connections

A	ANTENNA	75	B	ANTENNA	75
		FM			FM
		COAXIAL			COAXIAL
	AM	AM		AM	AM
		EXT			EXT
	LOOP			LOOP
			FM Antenna
ANTENNA			Extend the supplied FM antenna horizontally.
	FM 75
	COAXIAL

AM	Outdoor FM Antenna Cable
LOOP

AM

EXT

A.Using the Supplied FM Antenna

The FM antenna provided can be connected to the FM 75 Ω COAXIAL terminal as temporary measure.

B.Using the Standard Type Connector (Not Supplied)

A standard type connector (IEC or DIN45325) should be connected to the FM 75 Ω COAXIAL terminal.

Note:

If reception is poor, connect the outdoor antenna.

Before attaching a 75 Ω coaxial cable (the kind with a round wire going to an outdoor antenna), disconnect the supplied FM antenna.

3

AM (MW/LW) Antenna Connections

				Snap the tabs on the loop into the
				slots of the base to assemble the
ANTENNA
		FM 75		AM (MW/LW) loop.
		COAXIAL

AM

LOOP

AM		AM (MW/LW) Loop Antenna
EXT
1	2	3

Outdoor single vinyl-covered wire (not supplied)

Turn the loop until you have the best reception.

Notes:

• If the AM (MW/LW) loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown in the diagram.

•Make sure the antenna conductors do not touch any

other terminals, connecting cords and power cord. This could cause poor reception.

•If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM (MW/LW) loop antenna connected.)

Connecting the Speakers

Basic connecting procedure

1	2	3	4
	1		1
	RIGHT		RIGHT

1

RIGHT

1Cut, twist and remove the insulation at the end of each speaker signal cable (not supplied).

2Turn the knob counterclockwise.

3Insert the speaker signal cable.

4Turn the knob clockwise.

Connecting the front speakers

You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).

1

2

Right speaker

Right speaker

You can connect the following speakers:

•Two pairs of front speakers to produce normal stereo sound.

•One pair of rear speakers to enjoy the surround effect.

•One center speaker to produce more effective surround effect (to emphasize human voices).

•One subwoofer to enhance the bass.

IMPORTANT:

After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 14.

For each speaker (except for a subwoofer), connect the (+) and (–) terminals on the rear panel to the (+) and (–) terminals marked on the speakers. For connecting a subwoofer, see page 5.

CAUTION:

Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.

1	FRONT	2
	SPEAKERS
FRONT	+	+	FRONT
SPEAKERS	–	–	SPEAKERS
1			2
	RIGHT	LEFT
RIGHT	LEFT

Left speaker			Left speaker

4

About the speaker impedance

The required speaker impedance of the front speakers does differ depending on whether both the FRONT SPEAKERS 1 and FRONT SPEAKERS 2 terminals are used or only one of them is used.

CASE 1 When you connect only one pair of front speakers

Front	Front
speaker	speaker
1	1

Use front speakers with 8 Ω – 16Ω impedance.

CASE 2 When you connect two pairs of front speakers

Front	Front
speaker	speaker
2	2
Front	Front
speaker	speaker
1	1

Use front speakers 16 Ω – 32Ω impedance.

Connecting the rear and center speakers

Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.

Center speaker

		CENTER		REAR
				SPEAKERS
		SPEAKER

+

Left rear	Right rear
speaker	speaker

–

RIGHT LEFT

Connecting the subwoofer speaker

You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the

SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).

SUBWOOFER

OUT

Powered subwoofer

Connecting Audio/Video Components

You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components.

Audio Components	Video Components
• Turntable	• DVD player*
• CD player*	• TV*
• Cassette deck	• DBS tuner*
or CD recorder*	• VCR

*You can connect these components using the methods described in

“Analog connections” (below) or in “Digital connections” (see page

8).

Analog connections

Audio component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, and the red plug to the audio right jack.

CAUTION:

If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.

Turntable

If an earth cable is provided for your turntable, connect the cable to the AM (H) terminal on the rear panel.

Turntable

	PHONO
	CD
To audio
output	OUT
	(REC)
	TAPE
	CDR
Ex.: This connection is for the	IN
	(PLAY)
turntable with an MM (moving-
magnet) type cartridge.	OUT
	(REC)
	VCR
Note:	IN
	(PLAY)
Any turntables incorporating a small-output cartridgeTV		such as an MC
	SOUND
(moving-coil) type must be connected to this receiver through a
	DBS
commercial head amplifier or step-up transformer. DirectRIGHT connectionLEFT
may result in insufficient volume.		AUDIO

5

CD player

PHONO

CD player

	CD
	OUT
	(REC)
To audio output	TAPE
	CDR
	IN
	(PLAY)
	OUT
	(REC)
	VCR

Cassette deck or CD recorder

	Cassette deck
To audio input	To audio output

PHONO

CD

OUT (REC)

TAPE

CDR

IN (PLAY)

OUT (REC)

VCR

IN (PLAY)

TV

SOUND

DBS

RIGHT LEFT

AUDIO

To audio input					To audio output
		CD recorder

Note:

You can connect either a cassette deck or a CD recorder to the TAPE/

CDR jacks. When connecting a CD recorder to the TAPE/CDR jacks, change the source name, which will be shown on the display when selected as the source, to “CDR.” See page 13 for details.

If your audio components have a COMPU LINK jack

See also page 31 for detailed information about the connection and the COMPU LINK remote control system.

Video component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack.

If your video components have S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied). Connecting these video components through the S-video input/output terminals will give you better picture playback (or recording) quality.

IMPORTANT:

This receiver is equipped with both the composite video and S-video input/output terminals for connecting video components.

You do not have to connect both the composite video and S-video terminals.

However, remember that the video signals from the composite video input terminals are output only through the composite video output terminals, while the ones from the S-video input terminals are output only through the S-video output terminals.

Therefore, if a recording video component and a playing video component are connected to the receiver through the different video terminals, you cannot record the picture from the playing component on the recording component. In addition, if the TV and a playing video component are connected to the receiver through the different video terminals, you cannot view the playback picture from the playing component on the TV.

VCR

A		S-VHS (or VHS) VCR	C	D
	B		E	F

PHONO

CD

MONITOR

OUT OUT (REC)

TAPE
CDR		DVD
IN
(PLAY)
OUT		OUT
(REC)		(REC)
VCR		VCR
IN		IN
(PLAY)		(PLAY)
TV		DBS
SOUND
DBS
RIGHT	LEFT
AUDIO		VIDEO

Å To left/right channel audio output ı To left/right channel audio input Ç To S-video output

Î To composite video output ‰ To composite video input Ï To S-video input

6

TV and/or DBS tuner

To S-video input

To composite video input

	PHONO
	Connect the TV to the MONITOR
	OUT jack to view the playback
	CD
	picture from the other connected	MONITOR
	video components.
		OUT
	OUT
	(REC)
	TAPE
	CDR	DVD
	IN
	(PLAY)

OUT	OUT
(REC)	(REC)
VCR	VCR
IN	IN
(PLAY)	(PLAY)

TV

TV

	SOUND	DBS
To audio	DBS
	RIGHT LEFT
output
	AUDIO	VIDEO

When connecting the TV to the AUDIO jacks (TV SOUND/DBS), DO NOT connect the TV’s video output to these video input terminals.

DVD player

• When you connect the DVD player with stereo output jacks:

A

DVD player

B C

DVD

MONITOR

OUT

AUDIO

	RIGHT	LEFT
	FRONT		DVD
		DVD
	SUB	CENTER	OUT
			(REC)
	WOOFER
	REAR		VCR
			IN
			(PLAY)
	RIGHT	LEFT
			DBS
	SUBWOOFER
	OUT		VIDEO

Å To front left/right channel audio output (or to audio mixed output if necessary)

ı To S-video output

Ç To composite video output

• When you connect the DVD player with its analog discrete output (5.1 CH reproduction) jacks:

A

E

DVD player

C

							DVD
			VCR		VCR	B
			IN		IN	D	F
			(PLAY)		(PLAY)
			TV				MONITOR
					DBS		OUT
			SOUND			AUDIO
			DBS			RIGHT	LEFT
			RIGHT	LEFT
	To audio
		DBS tuner	AUDIO		VIDEO	FRONT	DVD
	output
							DVD

DBS

To composite video output

To S-video output

Note:

When connecting the DBS tuner to the TV SOUND/DBS jacks, change the source name, which will be shown on the display when selected as the source, to “DBS.” See page 13 for details.

SUB	CENTER	OUT
WOOFER		(REC)

VCR

REAR

	IN
	(PLAY)
RIGHT	LEFT
	DBS
SUBWOOFER
OUT	VIDEO

Å To center channel audio output ı To subwoofer audio output

Ç To S-video output

Î To front left/right channel audio output ‰ To rear left/right channel audio output Ï To composite video output

7

Digital connections

This receiver is equipped with four DIGITAL IN terminals — one digital coaxial terminal and three digital optical terminals, and one DIGITAL OUT terminal.

You can connect any digital equipment such as —

•DBS tuner,

•Digital TV broadcast tuner,

•DVD player,

•CD player, and

•CD recorder.

IMPORTANT:

•When connecting the DVD player, digital TV broadcast tuner or DBS tuner using the digital terminals, you also need to connect it to the video jack (either composite video terminal or S-video terminal) on the rear. Without connecting it to the video jack, you can view no playback picture.

•After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary.

–Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 16.

–Select the digital input mode correctly. For details, see “Selecting the Analog or Digital Input Mode” on page 16.

Digital input terminals

Digital TV

DVD player

DVD

CD player

CD recorder

Notes:

•When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components.

–DIGITAL 1 (coaxial): For DVD player

–DIGITAL 2 (optical): For CD player

–DIGITAL 3 (optical): For digital TV broadcast tuner

–DIGITAL 4 (optical): For CD recorder

•When you want to operate the CD player or CD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see page 6).

Digital output terminal

CD recorder, etc.

Digital optical cable (not supplied) between digital optical terminals

When the digital recording equipment such as a CD recorder has a digital optical input terminal, connecting it to the DIGITAL OUT terminal enables you to perform

digital-to-digital recording. DOLBY DIGITAL/PCM

/DTS

DIGITAL OUT

Digital coaxial cable (not supplied) between digital coaxial terminals

Digital optical cable (not supplied) between digital optical terminals

When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DVD) terminal, using the digital coaxial cable (not supplied).

When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD), DIGITAL 3 (TV), or DIGITAL 4 (CDR) terminal, using the digital optical cable (not supplied).

Before connecting a digital optical cable, unplug the protective plug.

DIGITAL 1 (DVD)

DIGITAL 2 ( CD )

DIGITAL 3 ( TV )

DIGITAL 4 (CDR)

DIGITAL IN

8

Connecting the Power Cord

Before plugging the receiver into an AC outlet, make sure that all connections have been made.

Plug the power cord into an AC outlet.

Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.

Note:

The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:

–When you unplug the power cord.

–When a power failure occurs.

CAUTIONS:

•Do not touch the power cord with wet hands.

•Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.

Putting Batteries in the Remote Control

Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.

1

2

R6P(SUM-3)/AA(15F)

3

1.On the back of the remote control, remove the battery cover.

2.Insert batteries. Make sure to match the polarity:

(+) to (+) and (–) to (–).

3.Replace the cover.

If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.

CAUTION:

Follow these precautions to avoid leaking or cracking cells:

•Place batteries in the remote control so they match the polarity:

(+) to (+) and (–) to (–).

•Use the correct type of batteries. Batteries that look similar may differ in voltage.

•Always replace both batteries at the same time.

•Do not expose batteries to heat or flame.

9

Basic Operations

The following operations are commonly used when you play any sound source.

Turning the Power On and Off (Standby)

On the front panel:

To turn on the power, press STANDBY/ON				STANDBY
	. The STANDBY lamp goes off. The name
of the current source (or station frequency)				STANDBY/ON
appears on the display.
		Current source name appears
		SPK 1
		ANALOG L R		VOLUME

Current volume level is shown here

To turn off the power (into standby mode), press STANDBY/ON again. The STANDBY lamp lights up. A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.

From the remote control:

To turn on the power, press AUDIO . The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.

To turn off the power (into standby mode), press AUDIO again. The STANDBY lamp lights up.

STANDBY

STANDBY/ON

AUDIO

Selecting the Source to Play

Press one of the source selecting buttons.

On the front panel:

DVD MULTI	DVD	VCR	TV SOUND/DBS
			SOURCE NAME
PHONO	CD	TAPE/CDR	FM/AM
		SOURCE NAME

From the remote control:

DVD DVD MUILTI

CD

FM/AM

TV/DBS VCR TAPE/CDR PHONO

Selected source name appears

DIGITAL AUTO	SPK 1 2			BASS BOOST INPUT ATT	EON RDS	SLEEP
ANALOG	L	C	R	PROLOGIC DSP H.PHONE AUTOMUTING TUNED STEREO TA NEWS INFO VOLUME
LINEAR PCM	S.WFR LFE
DIGITAL	LS	S	RS
			CH-

DVD MULTI	Select the DVD player for viewing the digital
	video disc using the analog discrete output mode
	(5.1 CH reproduction).
	To enjoy the DVD MULTI playback, see page
	30.
DVD	Select the DVD player.
VCR	Select the video component connected to the
	VCR jacks.
TV SOUND/DBS Select TV sounds (or the DBS tuner).
PHONO*	Select the turntable.
CD*	Select the CD player.
TAPE/CDR*	Select the cassette deck (or the CD recorder).
FM/AM*	Select an FM or AM (MW/LW) broadcast.
	• Each time you press the button, the band

alternates between FM and AM (MW/LW).

Notes:

•When connecting a CD recorder (to the TAPE/CDR jacks), and a DBS tuner (to the TV SOUND/DBS jacks), change the source name shown on the display. For details, see page 13.

•When you press one of the source selecting buttons on the remote control marked above with an asterisk (*), the receiver automatically turns on.

Signal and speaker indicators on the display

The signal indicators light up in the following cases:

•Only the indicators for the incoming signals light up.

•When analog input is selected, “L” and “R” always light up.

•When “DVD MULTI” is selected as the source, “L,” “C,” “R,” “LFE,” “LS” and “RS” light up.

The speaker indicators light up only —:

•When the corresponding speaker is activated.

AND

•When the corresponding speaker is required for the DSP mode selected currently.

Signal indicators light up in	Speaker indicators light up
red:	in white:

L	C	R	L	C	R
S.WFR LFE			S.WFR LFE
LS	S	RS	LS	S	RS
L: • When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.

R: • When digital input is selected: Lights up when the right channel signal comes in.

• When analog input is selected: Always lights up.

C: Lights up when the center channel signal comes in. LS: Lights up when the left rear channel signal comes in. RS: Lights up when the right rear channel signal comes in.

S: Lights up when the monaural rear channel signal comes in. LFE: Lights up when the LFE channel signal comes in.

Notes:

• When “SUBWOOFER” is set to “YES,” S.WFR lights up.

•When you select “DVD MULTI,” all the signal indicators except “S” light up.

10

Selecting different sources for picture and sound

You can watch picture from a video component while listening to sound from another component.

Press one of the audio source selecting buttons — PHONO, CD, TAPE/CDR, FM/AM, TV SOUND/DBS* (or TV/DBS on the remote control), while viewing the picture from a video component such as the VCR, DVD player, or DBS tuner, etc.

Notes:

• Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.

*The TV SOUND/DBS (or TV/DBS on the remote control) only works for selecting “DBS” as the source but not for selecting “TV SOUND (or TV on the remote control).” When you use the DBS tuner, change the source name correctly (see page 13).

Adjusting the Volume

On the front panel:

To increase the volume, turn MASTER VOLUME clockwise.

To decrease the volume, turn it counterclockwise.

• When you turn MASTER VOLUME

rapidly, the volume level also changes rapidly.

• When you turn MASTER VOLUME slowly, the volume level also changes slowly.

From the remote control:

To increase the volume, press VOLUME +. To decrease the volume, press VOLUME –.

CAUTION:

MASTER VOLUME

+

VOLUME

−

Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.

Note:

The volume level can be adjusted within the range of “0” (minimum) to

“80” (maximum).

Selecting the Front Speakers

On the front panel ONLY:

When you have connected two pairs of the front speakers, you can select which to use.

SPEAKERS ON/OFF

1

2

To use the speakers connected to the FRONT SPEAKERS 1 terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator lights up on the display. (Make sure that the SPK 2 is not on the display.)

To use the speakers connected to the FRONT SPEAKERS 2 terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator lights up on the display. (Make sure that the SPK 1 is not on the display.)

To use both sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators light up on the display.

To use neither sets of the speakers, press SPEAKERS ON/OFF 1 and 2 so that the SPK 1 and SPK 2 indicators disappear from the display.

Notes:

•If you select any of the DSP modes while using both the speakers connected to the FRONT SPEAKERS 1 and 2 terminals, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.

•While the DSP MODE is in use, you can only select either the speakers connected to the FRONT SPEAKERS 1 or 2 terminals.

Listening only with headphones

You must turn off both pairs of speakers when you listen with headphones.

1.Connect a pair of headphones to the PHONES jack on the front panel.

2.Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so that neither the SPK 1 nor SPK 2 indicator appears on the display.

This cancels the DSP mode currently selected, and activates the HEADPHONE mode (see below).

•“HEADPHONE” appears and H. PHONE indicator lights up on the display.

HEADPHONE mode:

This mode can reproduce the LFE channel signals, mixing them with the front channel signals. So you will not miss the subwoofer sounds even if you listen to a source using the headphones.

Notes:

•While in the HEADPHONE mode, you cannot use any DSP modes (see page 23.)

•Activating the speaker cancels the HEADPHONE mode and turns on the DSP mode previously selected.

CAUTION:

Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.

11