JVC RX-5062-SE Service manual
SERVICE MANUAL
AUDIO/VIDEO CONTROL RECEIVER
MB50420062
RX-5060BJ,RX-5060BC,
RX-5060BE,RX-5062SB,
RX-5062SE,RX-5062SEN,
RX-5062SEV
TA/NEWS/INFO
DISPLAY MODE
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
COPYRIGHT © 2006 Victor Company of Japan, Limited
No.MB504
2006/2
SPECIFICATION
Northern america version
Amplifier
Output Power Front channels 100 W per channel, min. RMS, driven into 8
total harmonic distortion.
Center channel 100 W, min. RMS, driven into 8
ic distortion.
Surround channels 100 W per channel, min. RMS, driven int 8
total harmonic distortion.
Audio Audio Input Sensitivity/Impedance (1 kHz) CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 220 mV/47 k
Audio Input (DIGITAL IN)* Coaxial DIGITAL 1 (DVD) : 0.5 V(p-p)/75 Ω
Optical DIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm ±30 nm)
Recording Output Level TAPE/CDR, VCR : 220 mV
Signal-to-Noise Ratio ('66 IHF/'78 IHF) CD, TAPE/CDR, VCR, TV SOUND, DVD : 62 dB/71 dB
Frequency Response (8
Equalization (5 bands) 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : ±8 dB (in 2 dB steps)
Video Video Input Sensitivity/Impedance Composite video DVD, VCR, AUX : 1 V(p-p)/75
Video Output Level Composite video VCR, MONITOR OUT : 1 V(p-p)/75 Ω
Synchronization Negative
Signal-to-Noise Ratio 45 dB
Tuning Range 87.5 MHz to 108.0 MHz
Usable Sensitivity Monaural 12.8 dBf (1.2
50 dB Quieting Sensitivity Monaural 16.0 dBf (1.7
Stereo Separation at OUT (REC) 35 dB at 1 kHz
Tuning Range 530 kHz to 1 710 kHz
Power Requirements AC 120V , 60 Hz
Power Consumption 155 W/200 VA (at operation)
Dimensions (W
Mass 7.0 kg
× H × D) 435 mm × 146.5 mm × 369.5 mm
Ω) CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (±1 dB)
FM tuner (IHF)
µV/75 Ω)
µV/75 Ω)
Stereo 37.5 dBf (20.5
AM tuner
General
0.8 W (in standby mode)
µV/75 Ω)
Ω, at 1 kHz with no more than 10% total harmon-
Ω
Ω, at 1 kHz with no more than 10%
Ω, at 1 kHz with no more than 10%
Ω
1-2 (No.MB504)
Europian version
Amplifier
Output Power Front channels 100 W per channel, min. RMS, driven into 8
total harmonic distortion.
Center channel 100 W, min. RMS, driven into 8
ic distortion.
Surround channels 100 W per channel, min. RMS, driven into 8
total harmonic distortion.
Audio Audio Input Sensitivity/Impedance (1 kHz) CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 220 mV/47 k
Audio Input (DIGITAL IN) Coaxial DIGITAL 1 (DVD) : 0.5 V(p-p)/75 Ω
Optical DIGITAL 2 (CD) : -21 dBm to -15 dBm (660 nm ±30 nm)
Recording Output Level TAPE/CDR, VCR : 220 mV
Signal-to-Noise Ratio ('66 IHF/DIN) CD, TAPE/CDR, VCR, TV SOUND, DVD : 66 dB/62 dB
Frequency Response (8
Equalization (5 bands) 63 Hz, 250 Hz, 1 kHz, 4 kHz, 16 kHz : ±8 dB (in 2 dB steps)
Video Video Input Sensitivity/Impedance Composite video DVD, VCR, AUX : 1 V(p-p)/75
Video Output Level Composite video VCR, MONITOR OUT : 1 V(p-p)/75 Ω
Synchronization Negative
Signal-to-Noise Ratio 45 dB
Tuning Range 87.50 MHz to 108.00 MHz
Usable Sensitivity Monaural 17.0 dBf (1.9
50 dB Quieting Sensitivity Monaural 21.3 dBf (3.2
Stereo Separation at OUT (REC) 35 dB at 1 kHz
Tuning Range 522 kHz to 1 629 kHz
General
Power Requirements AC 230 V , 50 Hz
Power Consumption 140 W (at operation)
Dimensions (W
Mass 7.0 kg
× H × D) 435 mm × 146.5 mm × 369.5 mm
Ω) CD, TAPE/CDR, VCR, TV SOUND, DVD, AUX : 20 Hz to 20 kHz (±1 dB)
FM tuner (IHF)
µV/75 Ω)
µV/75 Ω)
Stereo 41.3 dBf (31.8
AM (MW) tuner
0.8 W (in standby mode)
µV/75 Ω)
Ω, at 1 kHz with no more than 10% total harmon-
Ω
Ω, at 1 kHz with no more than 10%
Ω, at 1 kHz with no more than 10%
Ω
* Corresponding to Linear PCM, Dolby Digital, and DTS Digital Surround (with sampling frequency?32 kHz, 44.1 kHz, 48 kHz)
Designs and specifications are subject to change without notice.
(No.MB504)1-3
SECTION 1
PRECAUTION
1.1 Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2 Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3 Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4 Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
1-4 (No.MB504)
1.5 Importance administering point on the safety
FW201
FC211
B104
PW103
FC261
FC262
CN251
FC221
FC271
FC272
110 111112 113114 120121 122130 131
FC212
B103
PW101
EP1
R1
B107
PW102
B101
B102
B108
PW105
B106
FC222
TA201TA202
B105
PW104
B110
B109
R201
FC231
FC232
Full Fuse Replacement Marking
Graphic symbol mark
(This symbol means fast blow type fuse.)
should be read as follows ;
FUSE CAUTION
FOR CONTINUED PROTECTION AGAINST RISK
OF FIRE, REPLACE ONLY WITH SAME TYPE
AND RATING OF FUSES ;
F201,F206,F207: 5A 125V
F202,F203 : 2A 125V
Marquage Pour Le Remplacement
Complet De Fusible
Le symbole graphique (Ce symbole signifie
fusible de type a fusion rapide.)
^
doit etre interprete comme suit ;
PRECAUTIONS SUR LES FUSIBLES
POUR UNE PROTECTION CONTINUE CONTRE
DES RISQUES D'INCENDIE, REMPLACER
SEULEMENT PAR UN FUSIBLE DU MEME TYPE ;
F201,F206,F207: 5A 125V
F202,F203 : 2A 125V
(No.MB504)1-5
Loading...