JVC KD-R995BTS, KD-R990BTS, KD-R895BTS, KD-R792BT, KD-R790BT Instruction Manual

...

Download

Page 1

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

KD-R995BTS / KD-R990BTS / KD-R895BTS / KD-R792BT / KD-R790BT / KD-RD99BTS / KD-RD79BT / KD-R99MBS

CD RECEIVER

INSTRUCTION MANUAL

JS_JVC_KD_R995BTS_K_C.indd 1JS_JVC_KD_R995BTS_K_C.indd 1 7/6/2017 8:36:57 AM7/6/2017 8:36:57 AM

Page 2

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

ENGLISH

CONTENTS BEFORE USE

IMPORTANT

• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.

• Please keep the manual in a safe and accessible place for future reference.

WARNING

•

Do not operate any function that takes your attention away from safe driving.

•

Do not ingest the battery, Chemical Burn Hazard

The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accidents.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.

• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

• Depending on the types of cars, the antenna will automatically extend when you turn on the unit with the antenna control wire connected

( 42)

. Turn off the unit when parking at a low ceiling area.

Remote control (RM-RK52):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

BEFORE USE 2

BASICS 3

GETTING STARTED 4

1 Cancel the demonstration 2 Set the clock and date 3 Set the basic settings

RADIO 5

CD/USB/iPod/ANDROID 8

Pandora® 10

iHeartRadio® 11

Spotify 12

SiriusXM® Radio 13

BLUETOOTH® 16

AUX 24

AUDIO SETTINGS 24

DISPLAY SETTINGS 29

LEARNING STEERING REMOTE CONTROL 31

REFERENCES 32

Maintenance More information

TROUBLESHOOTING 36

SPECIFICATIONS 39

INSTALLATION/ CONNECTION 40

How to read this manual

• Operations are explained mainly using buttons on the faceplate of

KD-R995BTS

• English indications are used for the purpose of explanation. You can select the display language from the menu.

( 5)

•

[XX]

indicates the selected items.

•

( XX)

indicates references are available on the stated page.

JS_JVC_KD_R995BTS_K_EN_03.indd 2JS_JVC_KD_R995BTS_K_EN_03.indd 2 7/6/2017 8:40:33 AM7/6/2017 8:40:33 AM

Page 3

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

ENGLISH

BASICS

To On the faceplate On the remote control

Turn on the power

Press

• Press and hold to turn off the power.

( Not available )

Adjust the volume Turn the volume knob. Press

or .

• Press and hold

to continuously increase the

volume to 15.

Press the volume knob to mute the sound or pause playback.

• Press again to cancel. The volume level returns to the previous level before muting or pause.

Press

to mute the sound or pause playback.

• Press again to cancel. The volume level returns to the previous level before muting or pause.

Select a source

• Press

repeatedly.

• Press

, then turn the volume knob within 2 seconds.

Press SOURCE repeatedly.

Change the display information

Press

repeatedly.

( 34, 35)

( Not available )

Remote control (RM-RK52)

(supplied for KD-R792BT)

Other models can be remotely controlled with an optionally purchased remote control.

Attach How to resetDetach

Volume knob Loading slot

Detach button

Display window

Faceplate

KD-R995BTS:

USB cable from the rear of the unit

How to replace the battery

Remote sensor (Do not expose to bright sunlight.)

Pull out the insulation sheet when using for the first time.

Reset the unit within 5 seconds after detaching the faceplate.

JS_JVC_KD_R995BTS_K_EN_03.indd 3JS_JVC_KD_R995BTS_K_EN_03.indd 3 7/6/2017 10:48:36 AM7/6/2017 10:48:36 AM

Page 4

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

GETTING STARTED

Cancel the demonstration

When you turn on the power for the first time (or

[FACTORY RESET]

is set

[YES], 5

), the display shows: “CANCEL DEMO” “PRESS” “VOLUME

KNOB”

1 Press the volume knob.

[YES]

is selected for the initial setup.

2 Press the volume knob again.

“DEMO OFF” appears.

Set the clock and date

Press and hold .

2 Turn the volume knob to select

[CLOCK]

, then press the knob.

To adjust the clock

3 Turn the volume knob to select

[CLOCK ADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Hour

Minute

5 Turn the volume knob to select

[CLOCK FORMAT]

, then press the knob.

6 Turn the volume knob to select

[12H]

[24H]

, then press the knob.

To set the date

7 Turn the volume knob to select

[DATE SET]

, then press the knob.

8 Turn the volume knob to make the settings, then press the knob.

Day

Month Year

9 Press to exit.

To return to the previous setting item, press

Set the basic settings

Press and hold .

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press

Default:

SYSTEM

KEY BEEP

(Not applicable when 3-way crossover is selected.)

:Activates the keypress tone.;

OFF

:Deactivates.

SOURCE SELECT

AM SRC

:Enables AM in source selection.;

OFF

:Disables.

( 5)

PANDORA SRC

*ON

:Enables PANDORA FRONT/PANDORA REAR/PANDORA in source

selection.;

OFF

:Disables.

( 10)

IHEART SRC

:Enables IHEARTRADIO-F/IHEARTRADIO-R/IHEARTRADIO in source

selection.;

OFF

:Disables.

( 11)

SPOTIFY SRC

:Enables SPOTIFY FRONT/SPOTIFY REAR/SPOTIFY in source

selection.;

OFF

:Disables.

( 12)

BUILT-IN AUX

*ON

:Enables AUX in source selection.;

OFF

:Disables.

( 24)

USER S. REMO

(for

KD-R792BT

)

See page31 for details.

Not displayed when the corresponding source is selected.

JS_JVC_KD_R995BTS_K_EN_03.indd 4JS_JVC_KD_R995BTS_K_EN_03.indd 4 7/6/2017 8:40:37 AM7/6/2017 8:40:37 AM

Page 5

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

F/W UPDATE

UPDATE SYSTEM

F/W UP xxxx

YES

:Starts upgrading the firmware.;

:Cancels (upgrading is not activated).

FACTORY RESET

YES

:Resets the settings to default (except the

stored station).;

:Cancels.

CLOCK

TIME SYNC

:The clock time is automatically set using

the Clock Time (CT) data in FM Radio Broadcast Data System signal/FM Radio Data System

signal.;

OFF

:Cancels.

CLOCK DISPLAY

:The clock time is shown on the

display even when the unit is turned off.;

OFF

:Cancels.

ENGLISH

Select the display language for menu and music information if applicable. By default,

ENGLISH

is selected.

ESPANOL

RADIO

“ST” or “STEREO” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Search for a station

Press repeatedly to select FM or AM.

2 Press (or press on the remote control) to search for a station automatically.

(or) Press and hold

(or press and hold on the remote control) until “M” flashes,

then press repeatedly to search for a station manually.

Settings in memory

You can store up to 18 stations for FM and 6 stations for AM.

Store a station

While listening to a station....

Press and hold one of the number buttons (1 to 6).

(or) 1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob.

The preset number flashes and “MEMORY” appears.

Select a stored station

Press one of the number buttons (1to6).

(or) 1 Press . 2 Turn the volume knob to select a preset number, then press the knob.

GETTING STARTED

JS_JVC_KD_R995BTS_K_EN_03.indd 5JS_JVC_KD_R995BTS_K_EN_03.indd 5 7/6/2017 8:40:39 AM7/6/2017 8:40:39 AM

Page 6

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Other settings

Press and hold .

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press

Default:

TUNER SETTING (except KD-R792BT)

RADIO TIMER

Turns on the radio at a specific time regardless of the current source.

1 ONCE/DAILY/WEEKLY/OFF

:Select how often the timer will be

turned on.

2 FM/AM/SIRIUS XM

:Select the source.

3 01

to 18 (for FM/SIRIUS XM)/01 to 06 (for AM):Select the preset

station.

Set the activation day

and time.

“

” lights up when complete.

Radio Timer will not activate for the following cases.

• The unit is turned off.

•

[OFF]

is selected for

[AM SRC]

[SOURCE SELECT]

after Radio Timer

for AM is selected.

( 4)

SSM

SSM 01–06 /SSM 07–12 /SSM 13–18

:Automatically presets up to 18

stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select

SSM 07–12/SSM 13–18

to store the following 12 stations.

RADIO

IF BAND AUTO

:Increases the tuner selectivity to reduce interference noises from

adjacent FM stations. (Stereo effect may be lost.);

WIDE

:Subjects to

interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

MONO SET ON

:Improves the FM reception, but the stereo effect will be lost.;

OFF

:Cancels.

AREA N.AMERICA

: For North/Central/South America, AM/FM intervals:

10kHz/200kHz.;

S.AMERICA

:For some South American countries, AM/

FM intervals: 10kHz/50kHz.;

EUROPE

:For any other areas, AM/FM

intervals: 9kHz/50kHz.

PTY SEARCH

Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

: Selectable only

when SiriusXM Vehicle Tuner is connected.

( 13)

Selectable only when

[ONCE]

[WEEKLY]

is selected in step 1.

Only for FM source.

PTY code

(except KD-R792BT)

NEWS

INFORM

(information),

SPORTS, TALK, ROCK, CLS ROCK

(classic rock),

ADLT HIT

(adult hits),

SOFT RCK

(softrock),

TOP 40, COUNTRY, OLDIES, SOFT

NOSTALGA

(nostalgia),

JAZZ, CLASSICL

(classical),

R & B

(rhythm and blues),

SOFT R&B

(soft rhythm and blues),

LANGUAGE, REL MUSC

(religious music),

REL TALK

(religious talk),

PERSNLTY

(personality),

PUBLIC, COLLEGE, HABL ESP

(Spanish talk),

MUSC ESP

(Spanish music),

HIP HOP, WEATHER

JS_JVC_KD_R995BTS_K_EN_03.indd 6JS_JVC_KD_R995BTS_K_EN_03.indd 6 7/6/2017 8:40:39 AM7/6/2017 8:40:39 AM

Page 7

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

RADIO

Default:

TUNER SETTING (for KD-R792BT)

RADIO TIMER

Turns on the radio at a specific time regardless of the current source.

1 ONCE/DAILY/WEEKLY/OFF

:Select how often the timer will be turned

on.

2 FM/AM

:Select the band.

3 01

to 18 (for FM)/01 to 06 (for AM):Select the preset station.

Set the activation day

and time.

“

” lights up when complete.

Radio Timer will not activate for the following cases.

• The unit is turned off.

•

[OFF]

is selected for

[AM SRC]

[SOURCE SELECT]

after Radio Timer for

AM is selected.

( 4)

SSM

SSM 01–06/SSM 07–12/SSM 13–18

: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select

SSM 07–12/SSM 13–18

to store the following 12 stations.

IF BAND AUTO

:Increases the tuner selectivity to reduce interference noises from

adjacent FM stations. (Stereo effect may be lost.);

WIDE

:Subjects to

interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.

MONO SET ON

:Improves the FM reception, but the stereo effect will be lost.;

OFF

:Cancels.

NEWS SET

:The unit will temporarily switch to News Programme if available.;

OFF

:Cancels.

REGIONAL

: Switches to another station only in the specific region using the “AF”

control.;

OFF

:Cancels.

AF SET

: Automatically searches for another station broadcasting the same

program in the same Radio Data System network with better reception

when the current reception is poor.;

OFF

: Cancels.

TI ON

: Allows the unit to temporarily switch to Traffic Information if available

(“TI” lights up) while listening to all sources except in AM. ;

OFF

:Cancels.

AREA N.AMERICA

: For North/Central/South America, AM/FM intervals:

10kHz/200kHz.;

S.AMERICA

:For some South American countries, AM/FM

intervals: 10kHz/50kHz.;

EUROPE

:For any other areas, AM/FM intervals:

9kHz/50kHz.

PTY SEARCH

Select a PTY code (see below). If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.

Selectable only when

[ONCE]

[WEEKLY]

is selected in step 1.

Only for FM source.

PTY code

(for KD-R792BT)

NEWS

AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP

(music),

ROCK M

(music),

EASY M

(music),

LIGHT M

(music),

CLASSICS, OTHER

(music),

WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL

LEISURE, JAZZ, COUNTRY, NATION M

(music),

OLDIES, FOLK M

(music),

DOCUMENT

JS_JVC_KD_R995BTS_K_EN_03.indd 7JS_JVC_KD_R995BTS_K_EN_03.indd 7 7/6/2017 8:40:40 AM7/6/2017 8:40:40 AM

Page 8

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

CD/USB/iPod/ANDROID

Selectable source:

•

KD-R995BTS: CD/USBFRONT/USBREAR/iPodFRONT/iPodREAR/ANDROIDFRONT/ANDROIDREAR

•

KD-R990BTS/KD-R895BTS/KD-R792BT/KD-R790BT/KD-RD99BTS/KD-RD79BT/KD-R99MBS: CD/USB/

iPodUSB/ANDROID

To On the faceplate On the remote control

Reverse/Fast-forward

Press and hold .

Press and hold

Select a track/file Press

Press

Select a folder

Press . Press .

Repeat play

Press repeatedly.

TRACK REPEAT/ALL REPEAT

: Audio CD

TRACK REPEAT/FOLDER REPEAT/ALL REPEAT

: MP3/WMA/AAC/WAV/

FLAC file

ONE REPEAT/ALL REPEAT/REPEAT OFF

: iPod or ANDROID

Random play

Press repeatedly.

ALL RANDOM/RANDOM OFF

: Audio CD

FOLDER RANDOM/ALL RANDOM/RANDOM OFF

: MP3/WMA/AAC/WAV/

FLAC file

SONG RANDOM/ALL RANDOM/RANDOM OFF

: iPod or ANDROID

Do not leave the cable inside the car when not using.

When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions

to install the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.

For ANDROID: Applicable only when

[AUTO MODE]

is selected.

( 9)

For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ANDROID.

For iPod/ANDROID: Applicable only when

[HEAD MODE]/[AUTO MODE]

is selected.

( 9)

Start playback

The source changes automatically and playback starts.

Eject disc

Label side

USB input terminal

USB 2.0 cable

(commercially available)

USB cable

(commercially available)

Accessory of the iPod/ iPhone

USB

iPod/iPhone

ANDROID

KD-R995BTS

: You can also connect to the USB cable from the rear of the unit.

JS_JVC_KD_R995BTS_K_EN_03.indd 8JS_JVC_KD_R995BTS_K_EN_03.indd 8 7/6/2017 8:40:40 AM7/6/2017 8:40:40 AM

Page 9

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Select control mode

While in iPodFRONT/iPodREAR/iPodUSB source, press repeatedly.

HEAD MODE

: Control iPod from this unit.

IPHONE MODE

: Control iPod using the iPod itself. However, you can still

play/pause or file skip from this unit.

While in ANDROIDFRONT/ANDROIDREAR/ANDROID source, press

repeatedly.

AUTO MODE

: Control Android device from this unit via JVC MUSIC PLAY

application installed in the Android device.

AUDIO MODE

: Control Android device using the Android device itself via

other media player applications installed in the Android device. However, you can still play/pause or file skip from this unit.

Select music drive

While in USBFRONT/USBREAR/USB source, press repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

Class).

• Selected drive of a multiple drives device.

Settings to use JVC Remote application

JVC Remote application is designed to control the JVC car receiver’s operations from the iPhone/iPod (via USB input terminal).

Preparation:

Install the latest version of JVC Remote application on your device before connecting.

You can make the settings in the same way as connection via Bluetooth.

( 22)

Select a file from a folder/list

For iPod/ANDROID, applicable only when

[HEAD MODE]/[AUTO MODE]

selected.

1 Press . 2 Turn the volume knob to select a folder/list, then press the knob. 3 Turn the volume knob to select a file, then press the knob.

Quick search

(applicable only for CD, USB FRONT, USB REAR, USB, ANDROID

FRONT, ANDROID REAR and ANDROID source)

If you have many files, you can search through them quickly.

Turn the volume knob quickly to browse through the list quickly.

Alphabet search

(applicable only for iPod FRONT, iPod REAR, iPod USB,

ANDROID FRONT, ANDROID REAR and ANDROID source)

You can search for a file according to the first character.

For iPodFRONT/iPodREAR/iPodUSB source Press

or turn the volume knob quickly to select the

desired character (A to Z, 0to9, OTHERS).

• Select “OTHERS” if the first character is other than AtoZ, 0to9.

For ANDROIDFRONT/ANDROIDREAR/ANDROID source

1 Press to enter character search. 2 Turn the volume knob to select the desired character.

^A^: Upper case letters (A to Z) _A_: Lower case letters (a to z)

-0-: Numbers (0 to 9)

-OTHERS-: Character other than AtoZ, 0to9 3 Press the volume knob to start searching.

• To return to the previous setting item, press

• To cancel, press and hold

CD/USB/iPod/ANDROID

JS_JVC_KD_R995BTS_K_EN_03.indd 9JS_JVC_KD_R995BTS_K_EN_03.indd 9 7/6/2017 8:40:41 AM7/6/2017 8:40:41 AM

Page 10

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Pandora®

(except KD-R792BT)

Preparation:

Install the latest version of the Pandora application on your device (iPhone/iPod touch), then create an account and log in to Pandora.

• Select

[ON]

for

[PANDORA SRC]

[SOURCE SELECT]. ( 4)

Start listening

Open the Pandora application on your device.

2 Connect your device to the USB input terminal.

3 Press repeatedly to select PANDORA FRONT/PANDORA

REAR/PANDORA.

Broadcast starts automatically.

To On the faceplate On the remote control

Playback/pause Press the volume knob.

Press

Skip a track

Press T. Press I.

Thumbs up or thumbs down*

Press . Press .

Do not leave the cable inside the car when not using.

If thumbs down is selected, the current track is skipped.

Create and store a new station

Press .

2 Turn the volume knob to select

[NEW STATION]

, then press the knob.

3 Turn the volume knob to select

[FROM TRACK]

[FROM ARTIST]

, then

press the knob.

A new station is created based on the current song or artist.

4 Press and hold one of the number buttons (3, 4, 5 or 6) to store.

To select a stored station: Press one of the number buttons (3, 4, 5 or 6).

Search for a registered station

Press .

2 Turn the volume knob to select an item, then press the knob.

[BY DATE]:

According to the registered date

[A-Z]:

By alphabetical order

3 Turn the volume knob to select the desired station, then press the

knob.

To cancel, press and hold

Bookmark current song information

Press and hold the volume knob.

“BOOKMARKED” appears and the information is stored to your device.

• The bookmark is available on your Pandora account but not on this unit.

USB input terminal

and/or

Accessory of the iPod/iPhone*

KD-R995BTS

: You can also connect to

the USB cable from the rear of the unit.

JS_JVC_KD_R995BTS_K_EN_03.indd 10JS_JVC_KD_R995BTS_K_EN_03.indd 10 7/6/2017 8:40:42 AM7/6/2017 8:40:42 AM

Page 11

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

iHeartRadio®

(except KD-R792BT)

Preparation:

Install the latest version of iHeartAuto application on your device (iPhone/iPod touch), then create an account and log in to iHeartRadio.

• Select

[ON]

for

[IHEART SRC]

[SOURCE SELECT]. ( 4)

Start listening

Open the iHeartAuto application on your device.

2 Connect your device to the USB input terminal.

3 Press repeatedly to select IHEARTRADIO-F/IHEARTRADIO-R/

IHEARTRADIO.

Broadcast starts automatically

* Do not leave the cable inside the car when not using.

To On the faceplate On the remote control

Playback/pause Press the volume knob.

Press

Skip a track for custom station

Press T. Press I.

Thumbs up or thumbs down

Press

. Press .

Create a new/ custom station

Press and hold the volume knob.

( Not available )

Scan for live station

1 Press 3 to start

scanning.

2 Press 3 again to listen

to the station.

( Not available )

Search and store a station

Press .

2 Turn the volume knob to select a category, then press the knob. 3 Turn the volume knob to select the desired station, then press the

knob.

When a city list appears, you can search cities in alphabetical order by

turning the volume knob quickly.

To cancel, press and hold

To store a station: Press and hold one of the number buttons (4, 5 or 6). To select a stored station: Press one of the number buttons (4, 5 or 6).

USB input terminal

Accessory of the iPod/iPhone*

KD-R995BTS

: You can also connect to

the USB cable from the rear of the unit.

and/or

JS_JVC_KD_R995BTS_K_EN_03.indd 11JS_JVC_KD_R995BTS_K_EN_03.indd 11 7/6/2017 8:40:43 AM7/6/2017 8:40:43 AM

Page 12

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Spotify

Preparation:

Install the latest version of the Spotify application on your device (iPhone/ iPod touch), then create an account and log in to Spotify.

• Select

[ON]

for

[SPOTIFY SRC]

[SOURCE SELECT]. ( 4)

Start listening

Open the Spotify application on your device.

2 Connect your device to the USB input terminal.

3 Press repeatedly to select SPOTIFYFRONT/SPOTIFYREAR/

SPOTIFY.

Broadcast starts automatically

* Do not leave the cable inside the car when not using.

To On the faceplate On the remote control

Playback/pause Press the volume knob.

Press

Skip a track

Press S

/ T. Press H

/ I.

Thumbs up or thumbs down

Press . Press .

Start radio Press and hold 5. ( Not available )

To On the faceplate On the remote control

Repeat play

Press repeatedly.

ALL REPEAT, ONE REPEAT

REPEAT OFF

( Not available )

Random play

Press repeatedly

ALL RANDOM, RANDOM OFF

( Not available )

Available for premium account users only.

This feature is available for tracks in Radio only. If thumbs down is selected, the current

track is skipped.

Available for tracks in Playlists only.

Save favorite song information

While listening to the Radio on Spotify...

Press and hold the volume knob.

“SAVED” appears and the information is stored to “Your Music” or “Your Library” on your Spotify account.

To unsave, repeat the same procedure. “REMOVED” appears and the information is removed from “Your Music” or “Your Library” on your Spotify account.

Search for a song or station

Press .

2 Turn the volume knob to select a list type, then press the knob.

The list types displayed differ depending on the information sent

from Spotify.

3 Turn the volume knob to select the desired song or station, then

press the knob.

You can browse through the list quickly by turning the volume knob

quickly.

To cancel, press and hold

USB input terminal

Accessory of the iPod/iPhone*

KD-R995BTS

: You can also connect to

the USB cable from the rear of the unit.

and/or

JS_JVC_KD_R995BTS_K_EN_03.indd 12JS_JVC_KD_R995BTS_K_EN_03.indd 12 7/6/2017 8:40:44 AM7/6/2017 8:40:44 AM

Page 13

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

SiriusXM® Radio

(for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)

Start listening

Press repeatedly to select SIRIUSXM.

2 Press .

“

” lights up.

3 Turn the volume knob to select a CATEGORY, then press the knob. 4 Turn the volume knob to select a category from the list, then press the knob.

If “ALL CHANNEL” is selected, all the available channels will be shown.

5 Turn the volume knob to select a channel, then press the knob.

(or) Press

to search for a channel manually.

• Pressing and holding

changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input screen appears. Enter the pass code to receive the channel.

( 15)

Settings in memory

You can store up to 18 channels.

Store a channel

While listening to a channel....

Press and hold one of the number buttons (1 to 6).

(or) 1 Press and hold the volume knob until “PRESETMODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob.

The preset number flashes and “MEMORY” appears.

Select a stored channel

Press one of the number buttons (1to6).

(or) 1 Press . 2 Turn the volume knob to select PRESET, then press the knob. 3 Turn the volume knob to select a preset number, then press the knob. (or)

Press

on the remote control.

Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and Subscription are required.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner

(commercially available).

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Vehicle Tuner and its packaging. The Radio ID does not include the letters I, O, S or F.

Press repeatedly to select SIRIUSXM to

start updating.

Antenna

Expansion port on the rear panel

SiriusXM Vehicle Tuner

JS_JVC_KD_R995BTS_K_EN_03.indd 13JS_JVC_KD_R995BTS_K_EN_03.indd 13 7/6/2017 8:40:45 AM7/6/2017 8:40:45 AM

Page 14

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Using SiriusXM tuner models later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.

• “

” appears at the last character of the channel name for the

SmartFavorites channels.

When you select a SmartFavorite channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if

[TUNE START]

is set

[ON] ( 15)

for most music channels stored as a SmartFavorite.

To On the faceplate

Select a stored SmartFavorite channel

Press one of the number buttons (1to6).

1 Press . 2 Turn the volume knob to select PRESET, then

press the knob.

3 Turn the volume knob to select a preset

number, then press the knob.

Cancel SmartFavorites channels

1 Press . 2 Turn the volume knob to select PRESET, then

press the knob.

3 Turn the volume knob to select a preset

number, then press and hold the knob.

“

” is removed from the last character.

Reassign SmartFavorites channels

Repeat steps

1 to 3 of cancelling SmartFavorites

channels.

“

” appears at the last character.

SiriusXM Replay™

While listening to a channel....

1 Press the volume knob.

“

” lights up and the unit memorizes this paused position.

2 Press the volume knob to start Replay.

Replay starts from the paused position in step

During Replay...

To On the faceplate On the remote control

Playback/pause Press the volume knob.

Press

Skip backward/ forward

Press

Rewind/Fast-forward Press and hold

Press and hold

Go to Live and exit Replay

Press and hold the volume knob.

Press and hold

1 Press . 2 Turn the volume knob

to select LIVE, then press the knob.

SmartFavorites and TuneStart™

User preset channels are initially assigned as the SmartFavorites channels. SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.

Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.

SiriusXM® Radio

(for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)

JS_JVC_KD_R995BTS_K_EN_03.indd 14JS_JVC_KD_R995BTS_K_EN_03.indd 14 7/18/2017 1:55:17 PM7/18/2017 1:55:17 PM

Page 15

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

TuneScan™

You can get a short preview of the songs that you have missed on each of your SmartFavorites music channels or currently tuned music channel.

1 Press . 2 Turn the volume knob to select TUNE SCAN, then press the knob.

Scanning start for the first 6 seconds of the recorded music contents.

• To listen to the current song, press the volume knob to stop scanning. The unit continues playing the current song.

• To select the previous/next song, press

• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.

SiriusXM settings

Press and hold .

2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press

Default:

SIRIUS XM

CHANNEL LOCK

To unlock settings:

Turn the volume knob to select a number.

Press to move to the entry position.

Repeat steps 1 and 2 to enter the current pass code.

(Initial pass code is 0000.)

Press the volume knob to confirm.

CODE SET

Press the volume knob to enter

[NEW CODE]

Turn the volume knob to select a number.

Press to move to the entry position.

Repeat steps 2 and 3 to enter a new 4-digit pass code.

Press the volume knob to confirm.

Repeat steps 2 to 5 to reconfirm the pass code.

• Make a note of the new pass code to enter channel lock settings for next time.

LOCK SETTING MATURE CH

:Selects the SiriusXM-defined lock setting.;

USER DEFINED

:Selects the individual channels the user wants to

lock.;

OFF

:Cancels.

CHANNEL EDIT

Turn the volume knob to select a category, then press the knob.

Turn the volume knob to select a channel you want to lock, then

press the knob. “L” appears in front of the channel number.

Press and hold to exit.

CHANNEL CLEAR

YES

:Clears all the locked channels.; NO:Cancels.

TUNE START

:All qualified music channels in the SmartFavorites will start

playback from the beginning of the song.;

OFF

:Cancels.

SIGNAL LEVEL

Shows the strength (

NO SIGNAL/WEAK/GOOD/STRONG

) of the

current received signal.

BUFFER USAGE

Shows the memory usage (0%to

100%

) for Replay buffer.

SXM RESET YES

:Resets stored channel and lock setting to default.; NO:Cancels.

Displayed only when

[USER DEFINED]

is selected.

Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports

SmartFavorites.

SiriusXM® Radio

(for KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS)

JS_JVC_KD_R995BTS_K_EN_03.indd 15JS_JVC_KD_R995BTS_K_EN_03.indd 15 7/6/2017 8:40:47 AM7/6/2017 8:40:47 AM

Page 16

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Pair and connect a Bluetooth device for the first time

Press to turn on the unit.

2 Search and select “KD-R9 BTS”/“KD-R8 BTS”/“KD-R7 BT”/“KD-RD9 BTS”/

“KD-RD7

BT”/“KD-R9 MBS” on the Bluetooth device.

“BTPAIRING” flashes on the display.

• For some Bluetooth devices, you may need to enter the Personal Identification Number

(PIN) code immediately after searching.

3 Perform (A) or (B) depending on what appears on the display.

For some Bluetooth devices, pairing sequence may vary from the steps described below.

(A) “[Device Name]”

“XXXXXX” “VOL–YES” “BACK–NO”

“XXXXXX” is a 6-digit passkey randomly generated during each pairing.

Ensure that the passkeys appear on the unit and Bluetooth device are the same. Press the volume knob to confirm the passkey. Operate the Bluetooth device to confirm the passkey.

(B) “[Device Name]”

“VOL–YES” “BACK–NO”

Press the volume knob to start pairing.

• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the Bluetooth device. You can change to a desired PIN code before pairing.

( 20)

• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing. “PAIRING COMPLETED” appears when pairing is completed and “

” will light up when the

Bluetooth connection is established.

• This unit supports Secure Simple Pairing (SSP).

• Up to five devices can be registered (paired) in total.

• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device,

20, [DEVICE DELETE]

• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.

However, while in BT AUDIO source, you can connect to five Bluetooth audio devices and

switch between these five devices. (

)

• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.

• Refer to the instruction manual of the Bluetooth device for more information.

BLUETOOTH®

BLUETOOTH — Connection

Supported Bluetooth profiles

– Hands-Free Profile (HFP) – Advanced Audio Distribution Profile (A2DP) – Audio/Video Remote Control Profile (AVRCP) – Serial Port Profile (SPP) – Phonebook Access Profile (PBAP)

Supported Bluetooth codecs

– Sub Band Codec (SBC) – Advanced Audio Coding (AAC)

Connect the microphone

* For the location of the microphone input terminal/microphone

input jack, refer to page“Connecting external amplifiers” on page43.

Adjust the microphone angle

Secure using cord clamps (not supplied) if necessary.

MIC (microphone input terminal)*

Microphone (supplied)

Rear panel

JS_JVC_KD_R995BTS_K_EN_03.indd 16JS_JVC_KD_R995BTS_K_EN_03.indd 16 7/6/2017 8:40:47 AM7/6/2017 8:40:47 AM

Page 17

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Auto Pairing

When you connect iPhone/iPod touch/ Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.

Press the volume knob to pair once you have confirmed the device name.

Automatic pairing request is activated only if: – Bluetooth function of the connected device is

turned on.

–

[AUTO PAIRING]

is set to

[ON]. ( 20)

– JVC MUSIC PLAY application is installed on

the Android device

( 8)

and

[AUTO MODE]

selected

( 9)

BLUETOOTH — Mobile phone

Receive a call

When there is an incoming call:

•

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

The buttons will blink in the color you have selected in

[RING COLOR]. ( 18)

KD-R792BT/KD-R790BT/KD-RD79BT

The buttons will blink in the blinking pattern you have selected in

[RING ILLUMI]. ( 18)

• The unit answers the call automatically if

[AUTO ANSWER]

is set to a selected time.

( 18)

During a call:

•

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

The buttons stop blinking and illuminate in the color you have selected in

[RING COLOR]. ( 18)

KD-R792BT/KD-R790BT/KD-RD79BT

The buttons stop blinking.

• If you turn off the unit or detach the faceplate, the Bluetooth connection is disconnected.

The following operations may differ or not available depending on the connected phone.

To On the faceplate On the remote control

First incoming call...

Answer a call

Press

or the volume knob.

Press

Reject a call

Press and hold

or the

volume knob.

Press and hold

End a call

Press and hold

or the

volume knob.

Press and hold

BLUETOOTH®

JS_JVC_KD_R995BTS_K_EN_03.indd 17JS_JVC_KD_R995BTS_K_EN_03.indd 17 7/6/2017 8:40:49 AM7/6/2017 8:40:49 AM

Page 18

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

To On the faceplate On the remote control

While talking on the first incoming call...

Answer another incoming call and hold the current call

Press

or the

volume knob.

( Not available )

Reject another incoming call

Press and hold or the volume knob.

( Not available )

While having two active calls...

End current call and activate held call

Press and hold or the volume knob.

Press and hold

Swap between the current call and held call

Press

( Not available )

Adjust the phone volume

[00]

[35]

(Default:

[15]

)

Turn the volume knob during a call.

Press

during a call.

Switch between hands-free and private talk modes

Press during a call.

( Not available )

This adjustment will not affect the volume of the other sources.

Press and hold to continuously increase the volume to 15.

Operations may vary according to the connected Bluetooth device.

Improve the voice quality

While talking on the phone....

1 Press and hold . 2 Turn the volume knob to select an item

(

see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press

Default:

MIC GAIN LEVEL –10

to

LEVEL +10(LEVEL –04

):The sensitivity of the

microphone increases as the number increased.

NR LEVEL LEVEL –05

to

LEVEL +05(LEVEL 00

):Adjust the noise

reduction level until the least noise is being heard during a phone conversation.

ECHO CANCEL LEVEL –05

to

LEVEL +05(LEVEL 00

):Adjust the echo

cancellation delay time until the least echo is being heard during a phone conversation.

Make the settings for receiving a call

Press to enter Bluetooth mode.

2 Turn the volume knob to select an item (see the following

table), then press the knob.

3 Repeat step 2 until the desired item is selected or activated.

To return to the previous setting item, press

Default:

SETTINGS

AUTO ANSWER

01 SEC

to

30 SEC

:The unit answers incoming call automatically in

the selected time (in seconds).;

OFF

:Cancels.

RING COLOR KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS

KD-R99MBS

COLOR 01

to

COLOR 49(COLOR 08

): Selects the light color for the

buttons as notification when there is an incoming call and during

a call.;

OFF

:Cancels.

RING ILLUMI KD-R792BT/KD-R790BT/KD-RD79BT

BLINK 01

to

BLINK 05(BLINK 02

): Selects the blinking pattern

for the buttons as notification when there is an incoming call.;

OFF

:Cancels.

BLUETOOTH®

JS_JVC_KD_R995BTS_K_EN_03.indd 18JS_JVC_KD_R995BTS_K_EN_03.indd 18 7/6/2017 8:40:51 AM7/6/2017 8:40:51 AM

Page 19

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

BATT/SIGNAL*KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

AUTO

:Shows the strength of the battery and signal when the unit detects a

Bluetooth device and the Bluetooth device is connected.;

OFF

:Cancels.

Functionality depends on the type of the phone used.

Make a call

You can make a call from the call history, phonebook, or dialing the number. Call by voice is also possible if your mobile phone has the feature.

1 Press to enter Bluetooth mode.

“(First device name)” appears.

• If two Bluetooth phones are connected, press again to switch to

another phone.

“(Second device name)” appears. 2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

To return to the previous setting item, press

RECENT CALL

(Applicable only if the phone supports PBAP.)

Press the volume knob to select a name or a phone number.

• “<” indicates call received, “>“ indicates call made, “M” indicates call missed.

• “NO HISTORY” appears if there is no recorded call history or call number.

Press the volume knob to call.

PHONEBOOK

(Applicable only if the phone supports PBAP.)

Press to select the desired letter (A to Z, 0to9, and OTHERS).

• “OTHERS” appears if the first character is other than Ato Z, 0 to 9.

Turn the volume knob to select a name, then press the knob.

Turn the volume knob to select a phone number, then press the knob to call.

• The phonebook of the connected phone is automatically transferred to the unit

when pairing.

• This unit can display only non-accent letters. (Accent letters such as “Ú” is

showns as “U”.)

BLUETOOTH®

DIAL NUMBER1 Turn the volume knob to select a number (0 to 9) or character

(

, #, +).

Press to move the entry position.

Repeat steps

and 2 until you finish entering the phone number.

Press the volume knob to call.

VOICE

Speak the name of the contact you want to call or the voice command to control the phone functions.

( Make a call using voice

recognition)

Make a call using voice recognition

Press and hold to activate the connected phone.

2 Speak the name of the contact you want to call or the voice

command to control the phone functions.

• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.

• This unit also supports the intelligent personal assistant function of iPhone.

Settings in memory

Store a contact in memory

You can store up to 6 contacts into the number buttons (1 to 6).

1 Press to enter Bluetooth mode. 2 Turn the volume knob to select

[RECENT CALL], [PHONEBOOK]

[DIAL NUMBER]

, then press the knob.

3 Turn the volume knob to select a contact or enter a phone

number.

If a contact is selected, press the volume knob to show the phone

number.

4 Press and hold one of the number buttons (1 to 6).

“MEMORY P(selected preset number)” appears when the contact

is stored.

To erase a contact from the preset memory, select

[DIAL NUMBER]

step

2 and store a blank number.

JS_JVC_KD_R995BTS_K_EN_03.indd 19JS_JVC_KD_R995BTS_K_EN_03.indd 19 7/6/2017 8:40:52 AM7/6/2017 8:40:52 AM

Page 20

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Make a call from memory

Press to enter Bluetooth mode.

2 Press one of the number buttons (1 to 6). 3 Press the volume knob to call.

“NO PRESET” appears if there is no contact stored.

Bluetooth mode settings

Press and hold .

2 Turn the volume knob to select an item

(

see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected/activated or follow the instructions

stated on the selected item.

4 Press to exit.

To return to the previous setting item, press

Default:

BT MODE

PHONE SELECT

Selects the phone or audio device to connect or disconnect. “

” appears in front of the device name when connected.

“

” appears in front of the current playback audio device.

AUDIO SELECT

DEVICE DELETE

Turn the volume knob to select a device to delete, then press the knob.

Turn the volume knob to select

[YES]

[NO]

, then press the knob.

PIN CODE EDIT (0000)

Changes the PIN code (up to 6 digits).

Turn the volume knob to select a number.

Press to move the entry position.

Repeat steps

and 2 until you finish entering the PIN code.

Press the volume knob to confirm.

RECONNECT ON

:The unit automatically reconnect when the last connected Bluetooth device is within

range.;

OFF

:Cancels.

AUTO PAIRING ON

:The unit automatically pair supported Bluetooth device (iPhone/iPod touch/Android

device) when it is connected through USB input terminal.Depending on the operating system

of the connected device, this function may not work. ;

OFF

:Cancels.

BLUETOOTH®

INITIALIZE YES

:Initializes all the Bluetooth settings (including

stored pairing, phonebook, and etc.).;

:Cancels.

INFORMATION MYBTNAME

: Displays the unit name

(“KD-R9

BTS”/“KD-R8 BTS”/“KD-R7 BT”/

“KD-RD9

BTS”/“KD-RD7 BT”/“KD-R9 MBS“).;

MYADDRESS

: Shows address of this unit.

You can only connect a maximum of two Bluetooth phones and one

Bluetooth audio device at any time.

Bluetooth compatibility check mode

You can check the connectivity of the supported profile between the Bluetooth device and the unit.

• Make sure there is no Bluetooth device paired.

1 Press and hold .

“BLUETOOTH”

“CHECK MODE” appears. “SEARCH

NOW USING PHONE”

“PIN IS 0000” scrolls on the

display.

2 Search and select “KD-R9 BTS”/“KD-R8 BTS”/

“KD-R7

BT”/“KD-RD9 BTS”/“KD-RD7 BT”/

“KD-R9

MBS“ on the Bluetooth device within

3minutes.

3 Perform (A), (B) or (C) depending on what appears

on the display.

(A) “PAIRING”

“XXXXXX” (6-digit passkey): Ensure

that the same passkey appears on the unit and Bluetooth device, then operate the Bluetooth device to confirm the passkey.

(B) “PAIRING”

“PIN IS 0000”: Enter “0000” on the

Bluetooth device.

confirm pairing.

JS_JVC_KD_R995BTS_K_EN_03.indd 20JS_JVC_KD_R995BTS_K_EN_03.indd 20 7/6/2017 8:40:53 AM7/6/2017 8:40:53 AM

Page 21

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

After pairing is successful, “PAIRING OK”

“[Device Name]” appears and Bluetooth compatibility check starts. If “CONNECT NOW USING PHONE” appears, operate the Bluetooth device to allow phonebook access to continue. “TESTING” flashes on the display.

The connectivity result flashes on the display.

“PAIRING OK” and/or “HANDS-FREE OK”*

and/

or “AUD.STREAM OK”*

and/or “PBAP OK”*3 :

Compatible *

Compatible with Hands-Free Profile (HFP)

Compatible with Advanced Audio Distribution Profile (A2DP)

Compatible with Phonebook Access profile (PBAP)

After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.

• To cancel, press and hold

to turn off the

power, then turn on the power again.

BLUETOOTH®

BLUETOOTH — Audio

Audio player via Bluetooth

Press repeatedly to select BTAUDIO (or press SOURCE on the remote control).

• Pressing enters BT AUDIO directly. 2 Operate the Bluetooth audio player to start playback.

To On the faceplate On the remote control

Playback/pause Press the volume knob.

Press

Select group or folder Press

. Press .

Reverse skip/Forward skip Press

Press

Reverse/Fast-forward Press and hold

Press and hold

Repeat play Press

repeatedly.

TRACK REPEAT, ALL REPEAT, REPEAT OFF

( Not available )

Random play

Press

repeatedly.

GROUP RANDOM, ALL RANDOM, RANDOM OFF

( Not available )

Select a file from a folder/ list

Refer to “Select a file from a folder/list” on page 9.

( Not available )

Switch between connected Bluetooth audio devices

Press 5.

( Not available )

* Pressing the “Play” key on the connected device itself also causes switching of sound output from the device.

Operations and display indications may differ according to their availability on the connected device.

While in BT AUDIO source, you can connect to five Bluetooth audio devices and switch between these five devices.

JS_JVC_KD_R995BTS_K_EN_03.indd 21JS_JVC_KD_R995BTS_K_EN_03.indd 21 7/6/2017 8:40:54 AM7/6/2017 8:40:54 AM

Page 22

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

STATUS

Shows the status of the selected device.

IOS CONNECTED

: You are able to use the application using the iPhone/iPod connected via Bluetooth or USB input terminal.

IOS NOT CONNECTED

: No IOS device is connected to use

the application.

ANDROID CONNECTED

: You are able to use the application using the Android smartphone connected via Bluetooth.

ANDROID NOT CONNECTED

: No Android device is

connected to use the application.

Listen to iPhone/iPod via Bluetooth

You can listen to the songs on the iPhone/iPod via Bluetooth on this unit.

Press

repeatedly to select iPodBT.

• You can operate the iPod/iPhone in the same way as iPod/iPhone via USB input terminal.

( 8)

• If you plug in an iPhone/iPod to the USB input terminal while listening to iPodBT source, the source automatically change to iPodUSB. Press

to select

iPodBT if the device is still connected via Bluetooth.

BLUETOOTH®

Settings to use JVC Remote application

JVC Remote application is designed to control the JVC car receiver’s operations from the iPhone/iPod (via Bluetooth or via USB input terminal) or Android smartphone (via Bluetooth).

Preparation:

Install the latest version of JVC Remote application on your device before connecting.

1 Press and hold . 2 Turn the volume knob to select an item

(

see the following table), then press the

knob.

3 Repeat step 2 until the desired item is selected or activated. 4 Press to exit.

To return to the previous setting item, press

Default:

REMOTE APP

SELECT

Select the device (IOS or ANDROID) to use the application.

IOS YES

:Selects iPhone/iPod to use the application via Bluetooth or connected via USB input

terminal.;

:Cancels.

If IOS is selected, select iPod BT source (or iPod USB if your iPhone/iPod is connected via USB input terminal) to activate the application.

• The connectivity of the application will be interrupted or disconnected if: – You change from iPod BT source to any playback source connected via the USB input terminal. – You change from iPod USB source to iPod BT source.

ANDROID YES

:Selects Android smartphone to use the application via Bluetooth.;NO: Cancels.

ANDROID LIST

Selects the Android smartphone to use from the list.

Displayed only when

[ANDROID]

[SELECT]

is set to

[YES]

JS_JVC_KD_R995BTS_K_EN_03.indd 22JS_JVC_KD_R995BTS_K_EN_03.indd 22 7/6/2017 8:40:55 AM7/6/2017 8:40:55 AM

Page 23

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Internet radio via Bluetooth

You can listen to internet radio (Pandora, iHeartRadio and Spotify) on the iPhone/iPod touch/Android device via Bluetooth on this unit.

• Make sure the USB input terminal is not connected to any device.

Listen to Pandora

(except KD-R792BT)

Preparation:

Select

[ON]

for

[PANDORA SRC]

[SOURCE SELECT]. ( 4)

1 Open the Pandora application on your device. 2 Connect your device via Bluetooth connection.

( 16)

3 Press repeatedly to select PANDORA (for iPhone/iPod) or

PANDORA BT (for Android device).

The source switches and broadcast starts automatically.

• You can operate Pandora in the same way as Pandora via USB input terminal.

( 10)

Listen to iHeartRadio

(except KD-R792BT)

Preparation:

Select

[ON]

for

[IHEART SRC]

[SOURCE SELECT]. ( 4)

1 Open the iHeartAuto application on your device. 2 Connect your device via Bluetooth connection.

( 16)

3 Press repeatedly to select IHEARTRADIO.

The source switches and broadcast starts automatically.

• You can operate iHeartRadio in the same way as iHeartRadio via USB input terminal.

( 11)

BLUETOOTH®

Listen to Spotify

Preparation:

Select

[ON]

for

[SPOTIFY SRC]

[SOURCE SELECT]. ( 4)

1 Open the Spotify application on your device. 2 Connect your device via Bluetooth connection.

( 16)

3 Press repeatedly to select SPOTIFY (for iPhone/iPod) or

SPOTIFY BT (for Android device).

The source switches and broadcast starts automatically.

• You can operate Spotify in the same way as Spotify via USB input terminal.

( 12)

JS_JVC_KD_R995BTS_K_EN_03.indd 23JS_JVC_KD_R995BTS_K_EN_03.indd 23 7/6/2017 8:40:56 AM7/6/2017 8:40:56 AM

Page 24

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Use a portable audio player

Connect a portable audio player (commercially available).

2 Select

[ON]

for

[BUILT-IN AUX]

[SOURCE SELECT]. ( 4)

3 Press repeatedly to select AUX. 4 Turn on the portable audio player and start playback.

Use a 3-core plug head stereo mini plug for optimum audio output.

3.5mm (1/8") stereo mini plug with “L”

shaped connector (commercially available)

Portable audio player

Auxiliary input jack

AUX AUDIO SETTINGS

1 Press and hold . 2 Turn the volume knob to select an item (see the following table),

then press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press

Default:

EQ SETTING

PRESET EQ

Select a preset equalizer suitable to the music genre.

• Select

[USER]

to use the settings made in

[EASY EQ]

[PRO EQ]

FLAT/DRVN 3/DRVN 2/DRVN 1/HARD ROCK/HIP HOP/JAZZ/POP/R&B

USER/CLASSICAL

Drive equalizer (

DRVN 3/DRVN 2/DRVN 1

) boosts specific frequencies in the audio signal to reduce the noise heard from outside the car or running noise of the tyres.

EASY EQ

Adjust your own sound settings.

• The settings are stored to

[USER]

• The settings made may affect the current settings of

[PRO EQ]

SUB.W SP

1*2

: 00to

+06

(Default:

+03

SUB.W

1*3

–50

to

+10

BASS

LVL–09

to

LVL+09

LVL 00

MID

LVL–09

to

LVL+09

LVL 00

TRE

LVL–09

to

LVL+09

LVL 00

)

1, *2, *3

( 25)

JS_JVC_KD_R995BTS_K_EN_03.indd 24JS_JVC_KD_R995BTS_K_EN_03.indd 24 7/6/2017 10:49:34 AM7/6/2017 10:49:34 AM

Page 25

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

PRO EQ

Adjust your own sound settings.

• The settings are stored to

[USER]

• The settings made may affect the current settings of

[EASY EQ]

62.5HZ

LEVEL –09

to

LEVEL +09 (LEVEL 00)

: Adjusts the level to memorize for each source.

(Before making an adjustment, select the source you want to adjust.)

:Turns on the extended bass.;

OFF

:Cancels.

100HZ/160HZ/250HZ/400HZ/630HZ/1KHZ/1.6KHZ/2.5KHZ/4KHZ/6.3KHZ/10KHZ

16kHZ

LEVEL –09

to

LEVEL +09 (LEVEL 00):

Adjusts the level to memorize for each source.

(Before making an adjustment, select the source you want to adjust.)

Q FACTOR 1.35/1.50/2.00

:Adjust the quality factor.

AUDIO CONTROL

BASS BOOST

LEVEL +01

to

LEVEL +05

: Selects your preferred bass boost level.;

OFF

:Cancels.

LOUDNESS LEVEL 01/LEVEL 02

:Boosts low or high frequencies to produce a well-

balanced sound at low volume.;

OFF

:Cancels.

SUB.W LEVEL

SPK-OUT

(Not applicable when 3-way crossover is selected.)

SUB.W 00

to

SUB.W +06(SUB.W +03

):Adjusts the

output level of the subwoofer connected via speaker lead.

( 42)

PRE-OUT

SUB.W –50

to

SUB.W +10(SUB.W 00

):Adjusts

the output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier.

( 43)

SUBWOOFER SET

: Turns on the subwoofer output.;

OFF

:Cancels.

FADER

(Not applicable when 3-way crossover is selected.)

POSITION R15

to

POSITION F15(POSITION 00

):Adjusts the front and

rear speaker output balance.

BALANCE

POSITION L15

to

POSITION R15(POSITION 00

):Adjusts the left and

right speaker output balance.

VOLUMEADJUST LEVEL –15

to

LEVEL +06(LEVEL 00

):Preset the initial volume level

of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust.

AMPGAIN LOWPOWER

:Limits the maximum volume level to 25. (Select if the maximum power of each speaker is less than 50W to prevent damaging the speakers.);

HIGH POWER

:The maximum volume level is 35.

SPK/PREOUT

(Not applicable when 3-way crossover is selected.) Depending on the speaker connection method, select the appropriate setting to get the desired output.

( 26, Speaker output settings)

SPEAKER SIZE

Depending on the crossover type you have selected (

[X ' OVER

TYPE]

), 2-way crossover or 3-way crossover setting items will be shown.

( 27, Crossover settings)

By default, 2-way crossover type is selected.

X ' OVER

DTA SETTINGS

For settings,

28, Digital Time Alignment settings

CAR SETTINGS

X ' OVER TYPE Caution

: Adjust the volume before changing the

[X ' OVER TYPE]

avoid the sudden increase or decrease of the output level.

2-WAY

(Displayed only when

[3-WAY]

is selected.)

YES

:Selects two way crossover type.; NO:Cancels.

3-WAY

(Displayed only when

[2-WAY]

is selected.)

YES

:Selects three way crossover type.; NO:Cancels.

Displayed only when

[SUBWOOFER SET]

is set to

[ON]

For 2-way crossover: Displayed only when

[SPK/PRE OUT]

is set to

[SUB.W/SUB.W]

( 26)

For 2-way crossover: Displayed only when

[SPK/PRE OUT]

is set to

[REAR/SUB.W]

[SUB.W/SUB.W]. ( 26)

This adjustment will not affect the subwoofer output.

AUDIO SETTINGS

JS_JVC_KD_R995BTS_K_EN_03.indd 25JS_JVC_KD_R995BTS_K_EN_03.indd 25 7/6/2017 8:40:58 AM7/6/2017 8:40:58 AM

Page 26

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

AUDIO SETTINGS

SOUND EFFECT

SPACE ENHANCE

(Not applicable for TUNER source.)

SMALL/MEDIUM/LARGE

: Virtually enhances the sound space.;

OFF

:Cancels.

SND RESPONSE LEVEL1/LEVEL2/LEVEL3

: Virtually makes the sound more realistic.;

OFF

:Cancels.

SOUND LIFT LOW/MIDDLE/HIGH

: Virtually adjust the sound position heard from

the speakers.;

OFF

:Cancels.

VOL LINK EQ ON

:Boosts the frequency to reduce the noise heard from outside the

car or running noise of the tyres.;

OFF

:Cancels.

K2 TECHNOLOGY

(Not applicable for TUNER source, SIRIUS XM source and AUX source.)

:Improve the sound quality of compressed music.;

OFF

:Cancels.

Speaker output settings

[SPK/PRE OUT]

(Applicable only if [X ' OVER TYPE ] is set to [2-WAY]) (

25)

Select the output setting for the speakers

[SPK/PRE OUT]

, based on the

speaker connection method.

Connection via lineout terminals

For connections through an external amplifier.

( 43)

KD-R995BTS

KD-R895BTS/KD-R99MBS

Setting on

[SPK/PRE OUT]

Audio signal through lineout terminal

FRONT REAR SW

REAR/REAR

(default) Front speakers

output

Rear speakers output Subwoofer output

REAR/SUB.W

( Not available ) ( Not available ) ( Not available )

SUB.W/SUB.W

Front speakers output

L (left): Subwoofer output R (right): (Mute)

Subwoofer output

KD-R990BTS/KD-R792BTKD-RD99BTS

Setting on

[SPK/PRE OUT]

Audio signal through lineout terminal

FRONT REAR/SW

REAR/REAR

Front speakers output Rear speakers output

REAR/SUB.W

(default) Front speakers output Subwoofer output

SUB.W/SUB.W

Front speakers output Subwoofer output

KD-R790BT/KD-RD79BT

Setting on

[SPK/PRE OUT]

Audio signal through lineout terminal

REAR/SW

REAR/REAR

Rear speakers output

REAR/SUB.W

(default) Subwoofer output

SUB.W/SUB.W

Subwoofer output

Connection via speaker leads

For connections without using an external amplifier. However, with this settings you can also enjoy the subwoofer output.

( 42)

Setting on

[SPK/PRE OUT]

Audio signal through rear speaker lead

L (left) R (right)

REAR/REAR

Rear speakers output Rear speakers output

REAR/SUB.W

Rear speakers output Rear speakers output

SUB.W/SUB.W

Subwoofer output (Mute)

[SUB.W/SUB.W]

is selected:

–

[120HZ]

is selected in

[SUBWOOFER LPF]

and

[THROUGH]

is not available.

–

[POSITION R02]

is selected in

[FADER]

and selectable range is

[POSITION

R15]

to

[POSITION 00]

JS_JVC_KD_R995BTS_K_EN_03.indd 26JS_JVC_KD_R995BTS_K_EN_03.indd 26 7/6/2017 8:40:59 AM7/6/2017 8:40:59 AM

Page 27

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

AUDIO SETTINGS

2-way crossover setting items

SPEAKER SIZE

FRONT SIZE

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8

6×9/7×10

TWEETER

SMALL/MIDDLE/LARGE/NONE

(not connected)

REAR

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9/7×10

NONE

(not connected)

SUBWOOFER

*2*

6.5"/8"/10"/12"/15" OVER/NONE

(not connected)

X ' OVER

TWEETER FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ

10KHZ/12.5KHZ

GAIN LEFT

–08DB

00DB

GAIN RIGHT

–08DB

00DB

FRONT HPF F-HPF FRQ

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

F-HPF SLOPE

–06DB/–12DB/–18DB/–24DB

F-HPF GAIN

–08DB

00DB

REAR HPF

R-HPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

R-HPF SLOPE

–06DB/–12DB/–18DB/–24DB

R-HPF GAIN

–08DB

00DB

SUBWOOFER LPF

*2*

SW LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ

120HZ/150HZ/180HZ/220HZ/250HZ/THROUGH

SW LPF SLOPE

–06DB/–12DB/–18DB/–24DB

SW LPF PHASE

REVERSE

(180°)/

NORMAL

(0°)

SW LPF GAIN –08DB

00DB

( 28)

Crossover settings

Below are the available setting items for 2-way crossover and 3-way crossover.

Caution

Select a crossover type according to how the speakers are connected.

( 42, 43)

If you select a wrong type:

• The speakers may damage.

• The output sound level may be extremely high or low.

SPEAKER SIZE

Selects according to the connected speaker size for optimum performance.

•

The frequency and slope settings are automatically set for the crossover of the selected speaker.

•

When 2-way crossover is selected, if

[NONE]

is selected for

[TWEETER]

[FRONT], [REAR]

and

[SUBWOOFER]

for

[SPEAKER SIZE]

, the

[X ‘ OVER]

setting

of the selected speaker is not available.

•

When 3-way crossover is selected, if

[NONE]

is selected for

[WOOFER]

[SPEAKER SIZE]

, the

[X ‘ OVER]

setting of

[WOOFER]

is not available.

X ‘ OVER

(crossover)

• [FRQ]/[F-HPF FRQ]/[R-HPF FRQ]/[SW LPF FRQ]/[HPF FRQ]/[LPF FRQ]

: Adjusts the crossover frequency for the selected speakers (high pass filter or low pass filter).

[THROUGH]

is selected, all signals are sent to the selected speakers.

• [SLOPE]/[F-HPF SLOPE]/[R-HPF SLOPE]/[SW LPF SLOPE]/[HPF SLOPE]

[LPF SLOPE]:

Adjusts the crossover slope.

Selectable only if a setting other than

[THROUGH]

is selected for the

crossover frequency.

• [SW LPF PHASE]/[PHASE]:

Selects the phase of the speaker output to be

in line with the other speaker output.

•

[GAIN LEFT]/[GAIN RIGHT]/[F-HPF GAIN]/[R-HPF GAIN]/[SW LPF GAIN]/[GAIN]:

Adjusts the output volume of the selected speaker.

JS_JVC_KD_R995BTS_K_EN_03.indd 27JS_JVC_KD_R995BTS_K_EN_03.indd 27 7/6/2017 8:41:00 AM7/6/2017 8:41:00 AM

Page 28

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

AUDIO SETTINGS

3-way crossover setting items

SPEAKER SIZE

TWEETER

SMALL/MIDDLE/LARGE

MID RANGE

3.5"/4"/4.75"/5"/6.5"/6.75"/7"/4×6/5×7/6×8/6×9

WOOFER

6.5"/8"/10"/12"/15" OVER/NONE

(not connected)

X ' OVER

TWEETER HPF FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ/10KHZ/12.5KHZ

SLOPE

–06DB/–12DB

PHASE

REVERSE

(180°)/

NORMAL

(0°)

GAIN –08DB

00DB

MID RANGE HPF FRQ

30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/120HZ

150HZ/180HZ/220HZ/250HZ/THROUGH

HPF SLOPE

–06DB/–12DB

LPF FRQ

1KHZ/1.6KHZ/2.5KHZ/4KHZ/5KHZ/6.3KHZ/8KHZ

10KHZ/12.5KHZ/THROUGH

LPF SLOPE

–06DB/–12DB

PHASE

REVERSE

(180°)/

NORMAL

(0°)

GAIN –08DB

00DB

WOOFER

LPF FRQ 30HZ/40HZ/50HZ/60HZ/70HZ/80HZ/90HZ/100HZ/120HZ

150HZ/180HZ/220HZ/250HZ/THROUGH

SLOPE

–06DB/–12DB

PHASE

REVERSE

(180°)/

NORMAL

(0°)

GAIN –08DB

00DB

Displayed only when

[SPK/PRE OUT]

is set to

[REAR/REAR]

[REAR/SUB.W]. ( 26)

Except

KD-R995BTS/KD-R895BTS/KD-R99MBS

: Displayed only when

[SPK/PRE OUT]

is set to

[REAR/SUB.W]

[SUB.W/SUB.W]. ( 26)

Displayed only when

[SUBWOOFER SET]

is set to

[ON]. ( 25)

Digital Time Alignment settings

Digital Time Alignment sets the delay time of the speaker output to create a more suitable environment for your vehicle.

• For more information,

29, Determining the value for [DISTANCE]

and [GAIN] of [DTA SETTINGS]

DTA SETTINGS

POSITION

Selects your listening position (reference point).

ALL

:Not compensating;

FRONT RIGHT:

Front right seat;

FRONT LEFT

:Front left seat;

FRONT ALL

:Front seat

•

[FRONT ALL]

is displayed only when

[X ' OVER TYPE]

set to

[2-WAY]. ( 25)

DISTANCE

0FT

20.01FT

:Fine adjust the distance to compensate.

GAIN

–8DB

0DB

:Fine adjust the output volume of the

selected speaker.

DTA RESET YES

:Resets the settings (

[DISTANCE]

and

[GAIN]

) of the

selected

[POSITION]

to default.; NO:Cancels.

CAR SETTINGS

Identify your car type and rear speaker location in order to make the adjustment for

[DTA SETTINGS]

CAR TYPE COMPACT/FULL SIZE CAR/WAGON/MINIVAN/SUV

MINIVAN(LONG)

:Selects the type of vehicle.;

OFF:

Not

compensating.

R-SP LOCATION

Selects the location of the rear speakers in your vehicle to calculate the furthest distance from the listening position selected (reference point).

•

DOOR/REAR DECK

:Selectable only when

[CAR TYPE]

is selected as

[OFF], [COMPACT], [FULL SIZE CAR]

[WAGON]

[SUV]

•

2ND ROW/3RD ROW

:Selectable only when

[CAR TYPE]

is selected as

[MINIVAN]

[MINIVAN(LONG)]

( 29)

JS_JVC_KD_R995BTS_K_EN_03.indd 28JS_JVC_KD_R995BTS_K_EN_03.indd 28 7/6/2017 8:41:00 AM7/6/2017 8:41:00 AM

Page 29

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

AUDIO SETTINGS

DISPLAY SETTINGS

Zone identification for brightness setting

KD-R792BT/KD-R790BT/KD-RD79BT/ KD-R99MBS

KD-R995BTS/KD-R990BTS/KD-R895BTS/ KD-RD99BTS

Zone identification for color setting

KD-R99MBSKD-R995BTS/KD-R990BTS/KD-R895BTS/

KD-RD99BTS

1 Press and hold . 2 Turn the volume knob to select an item (

), then press the

knob.

3 Repeat step 2 until the desired item is selected/activated or follow

the instructions stated on the selected item.

4 Press to exit.

To return to the previous setting item, press

Determining the value for [DISTANCE] and [GAIN] of [DTA SETTINGS]

If you specify the distance from the center of the currently set listening position to every speaker, the delay time will be automatically computed and set.

Determine the center of the currently set

listening position as the reference point.

Measure the distances from the reference

point to the speakers.

Calculate the differences between the distance

of the furthest speaker (rear speaker) and other speakers.

Set the

[DISTANCE]

calculated in step 3 for

individual speakers.

Adjust

[GAIN]

for individual speakers.

Example: When

[FRONT ALL]

is selected as the

listening position

Before making an adjustment, select the speaker:

When 2-way crossover is selected:

FRONT LEFT/FRONT RIGHT/REAR LEFT/REAR RIGHT/SUBWOOFER:

–

[REAR LEFT], [REAR RIGHT]

and

[SUBWOOFER]

is selectable only if a setting other than

[NONE]

is selected for

[REAR]

and

[SUBWOOFER]

[SPEAKER SIZE]. ( 27)

When 3-way crossover is selected:

TWEETER LEFT/TWEETER RIGHT/MID LEFT/MID RIGHT/WOOFER:

–

[WOOFER]

is selectable only if a setting other than

[NONE]

is selected for

[WOOFER]

[SPEAKER SIZE]. ( 28)

Displayed only when

[X ' OVER TYPE ]

is set to

[2-WAY] ( 25)

and if a setting other

than

[NONE]

is selected for [

REAR

] of

[SPEAKER SIZE]. ( 27)

JS_JVC_KD_R995BTS_K_EN_03.indd 29JS_JVC_KD_R995BTS_K_EN_03.indd 29 7/6/2017 8:41:01 AM7/6/2017 8:41:01 AM

Page 30

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Default:

DISPLAY

DIMMER

Dim the illumination.

OFF

:Dimmer is turned off. Brightness changes to

[DAY]

setting.

:Dimmer is turned on. Brightness changes to

[NIGHT]

setting.

( [BRIGHTNESS]) DIMMER TIME

:Set the dimmer on and off time.

Turn the volume knob to adjust the

[ON]

time, then press the knob.

Turn the volume knob to adjust the

[OFF]

time, then press the knob.

(Default:

[ON]: PM6:00

;

[OFF]: AM6:00

)

DIMMER AUTO

:Dimmer turns on and off automatically when you turn off or

on the car headlights.

BRIGHTNESS

Set the brightness for day and night separately.

1 DAY/NIGHT

:Select day or night.

Select a zone.

( 29)

3 LEVEL 00

LEVEL 31

: Set the brightness level.

TEXT SCROLL

SCROLL ONCE

:Scrolls the display information once.;

SCROLL AUTO

:Repeats

scrolling at 5-second intervals.;

SCROLL OFF

:Cancels.

COLOR

(for

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS

)

PRESET

Select illumination colors for the buttons on different zones separately.

Select a zone.

( 29)

Select a color for the selected zone.

•

COLOR 01

COLOR 49

•

USER

: The color you have created for

[DAY COLOR]

[NIGHT COLOR]

is shown.

•

COLOR FLOW01

COLOR FLOW03

: Color changes at different

speeds.

•

CRYSTAL/FLOWER/FOREST/GRADATION/OCEAN/SUNSET

RELAX

: The selected color pattern is shown.

(Selectable only when

[ALL ZONE]

is selected in step

1.)

DISPLAY SETTINGS

DAY COLOR

Store your own day and night illumination colors for different zones.

Select a zone.

( 29)

2 RED/GREEN/BLUE

:Select a primary color.

3 00

to 31:Select the level.

Repeat steps

and 3 for all the primary colors.

• Your setting is stored to

[USER]

[PRESET]

•

[NIGHT COLOR]

[DAY COLOR]

is changed by turning on or off your

car’s headlight.

NIGHT COLOR

COLOR GUIDE

:Changes the button illumination when settings are performed on

menu and list search.;

OFF

:Cancels.

COLOR

(for

KD-R99MBS

)

PRESET

Select illumination colors for the buttons.

•

COLOR 01

COLOR 49

•

USER

: The color you have created for

[DAY COLOR]

[NIGHT COLOR]

is shown.

•

COLOR FLOW01

COLOR FLOW03

: Color changes at different

speeds.

DAY COLOR

Store your own day and night illumination colors for the buttons.

1 RED/GREEN/BLUE

:Select a primary color.

2 00

to 31:Select the level.

Repeat steps

and 2 for all the primary colors.

• Your setting is stored to

[USER]

[PRESET]

•

[NIGHT COLOR]

[DAY COLOR]

is changed by turning on or off your

car’s headlight.

NIGHT COLOR

( 31)

JS_JVC_KD_R995BTS_K_EN_03.indd 30JS_JVC_KD_R995BTS_K_EN_03.indd 30 7/6/2017 10:53:52 AM7/6/2017 10:53:52 AM

Page 31

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

You can control the unit with the steering remote control keys on your vehicle. After connection, you can configure the control keys according to your preference.

• You can only make this configuration if your vehicle is equipped with the electrical steering remote control.

• If the steering remote control in your car is not compatible, configuration may not be completed and an error message may appear.

( 36)

Make the connection

Configure the control keys

Press and hold .

2 Turn the volume knob to select

[SYSTEM]

, then press the knob.

3 Turn the volume knob to select

[USER S.REMO]

, then press the knob.

4 Turn the volume knob to select

[SET KEY]

, then press the knob.

A key list of 16 assignable keys appears.

•

K## NONE

: No function has been assigned.

5 Turn the volume knob to select any key from the key list to assign the function, then press

the knob.

“PRESS KEY TO ASSIGN K##” appears.

DISPLAY SETTINGS

MENU COLOR ON

: The color of button illumination changes to white color when in menu mode or when selecting a music file from a folder/list.;

OFF

:Cancels.

The illumination control wire connection is required.

( 42)

Some characters or symbols will not be shown correctly

(or will be blanked).

If one of these color pattern is selected, the

[ZONE 1]

and

[ZONE 2]

illumination colors will change to the

default colors.

LEARNING STEERING REMOTE CONTROL

(for KD-R792BT)

Rear panel

Learning steering remote input terminal

Gray/red

Bright green/red

Purple/red

Steering remote cable (supplied)

Connect to your vehicle’s steering remote harness. Contact your JVC dealer for details.

JS_JVC_KD_R995BTS_K_EN_03.indd 31JS_JVC_KD_R995BTS_K_EN_03.indd 31 7/6/2017 8:41:03 AM7/6/2017 8:41:03 AM

Page 32

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

REFERENCES

Maintenance

Cleaning the unit

Wipe off dirt on the faceplate with a dry silicone or soft cloth.

Cleaning the connector

Detach the faceplate and clean the connector gently with a cotton swab, being careful not to damage the connector.

Handling discs:

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move outward.

• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.

• When removing discs from this unit, pull them out horizontally.

• Remove burrs from the center hole and disc edge before inserting a disc.

General

• This unit can only play the following CDs:

•

DualDisc playback:

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended.

Connector (on the reverse side of the faceplate)

LEARNING STEERING REMOTE CONTROL

(for KD-R792BT)

6 Press and hold any control keys on your steering remote control which

you want to assign.

A list of key functions will appear on the display.

NONE

(default)/MUTE/SEEK UP/SEEK DOWN/VOL UP/VOL DOWN/MODE/ON HOOK

OFF HOOK/VOICE/ENTER

7 Turn the volume knob to select a function to assign, then press the knob.

The selected key function is assigned to the steering remote control key you have selected in step 6. The display returns to the key list as on step 4.

•

K## (Function)

: When certain function has been assigned to a key.

8 Repeat steps 5, 6 and 7 to assign other control keys. 9 Press to exit.

To reassign the control keys 1

Press and hold .

2 Turn the volume knob to select

[SYSTEM]

, then press the knob.

3 Turn the volume knob to select

[USER S.REMO]

, then press the knob.

4 Turn the volume knob to select

[RESET KEY]

, then press the knob.

5 Turn the volume knob to select

[YES]

, then press the knob.

All the control keys will be reset.

Selecting

[NO]

will cancel the operation.

When

[FACTORY RESET]

is set to

[YES] ( 5)

, it will also reset the learning remote

control. To return to the previous setting item, press

JS_JVC_KD_R995BTS_K_EN_03.indd 32JS_JVC_KD_R995BTS_K_EN_03.indd 32 7/18/2017 12:05:15 PM7/18/2017 12:05:15 PM

Page 33

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

REFERENCES

Playable files

• Playable audio file: For disc: MP3(.mp3), WMA(.wma), AAC(.aac) For USB mass storage class device:

MP3(.mp3), WMA(.wma), AAC(.aac), AAC(.m4a), WAV (.wav), FLAC (.flac)

•

Playable disc media: CD-R/CD-RW/CD-ROM

• Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.

• Playable USB device file system: FAT12, FAT16, FAT32

Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device. The AAC (.m4a) file in a CD encoded by iTunes cannot be played on this unit.

Unplayable discs

• Discs that are not round.

• Discs with coloring on the recording surface or discs that are dirty.

• Recordable/ReWritable discs that have not been finalized.

• 8cm CD. Attempting to insert using an adapter may cause malfunction.

About USB devices

• You cannot connect a USB device via a USB hub.

• Connecting a cable whose total length is longer than 5m may result in abnormal playback.

• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1.5A.

About iPod/iPhone

• Via USB input terminal: Made for – iPod touch (5th and 6th generation) – iPod nano (7th generation) – iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus

• Via Bluetooth: Made for – iPod touch (5th and 6th generation) – iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus

• It is not possible to browse video files on the “Videos” menu in

[HEAD MODE]

• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.

• Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit.

About Android device

• This unit supports Android OS 4.1 and above.

• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory

(AOA)2.0.

• If the Android device supports both mass storage class device and AOA2.0, this unit always playback via AOA2.0 as priority.

About iHeartRadio

• iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.

• Some iHeartRadio® functionality cannot be operated from this unit.

About Spotify

• Spotify application supports: – iPhone 4S, 5, 5S, 5C, 6, 6 Plus, 6S, 6S Plus, SE, 7, 7 Plus (iOS 8 or above) – iPod touch (5th and 6th generation) – Android OS 4.0.3 or above

• Spotify is a third party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.

• Some functions of Spotify cannot be operated from this unit.

JS_JVC_KD_R995BTS_K_EN_03.indd 33JS_JVC_KD_R995BTS_K_EN_03.indd 33 7/6/2017 8:41:04 AM7/6/2017 8:41:04 AM

Page 34

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

REFERENCES

About Bluetooth

• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.

• This unit may not work with some Bluetooth devices.

• Signal conditions vary, depending on the surroundings.

Change the display information

Each time you press , the display information changes.

• If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg. station name) appears or display will be blank.

Source name

Display information

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS KD-R792BT/KD-R790BT/KD-RD79BT

Frequency (Date/Clock)

Frequency (Date) with music synchronisation*2 (back to the

beginning)

Frequency Clock Frequency with music synchronisation*2 (back to the beginning)

(For FM Radio Broadcast Data System stations only)

Station name (PS)/Program type (PTY) (Date/Clock)

Radiotext (Date/Clock)

Radiotext+ (Radiotext+)

Song title (Artist) Song title (Date/Clock)

Frequency

(Date/Clock)

Station name (PS)/Program type (PTY) (Date) with music synchronisation*2

(back to the beginning)

(For FM Radio Broadcast Data System stations/FM Radio Data signal only)

Station name (PS)/Program type (PTY) Radiotext Radiotext+

Radiotext+ title/Radio text+ artist Frequency

Clock Station name (PS)/Program type (PTY) with music

synchronisation*

(back to the beginning)

USB FRONT/

USB REAR/USB

(For CD-DA)

Track title (Artist) Track title (Disc name) Track title (Date/Clock)

Playing time (Date/

Clock)

Track title (Artist) with music synchronisation*2 (backtothebeginning)

(For CD-DA)

Disc title/Artist Track title/Artist Playing time Clock Disc title/Artist with music synchronisation*

(back to the

beginning)

(For MP3/WMA/AAC/WAV/FLAC files)

Song title (Artist) Song title (Album name) Song title (Date/Clock)

File name (Folder

name)

File name (Date/Clock)

Playing time (Date/Clock)

Song title (Artist) with

music synchronisation*

(backtothebeginning)

(For MP3/WMA/AAC/WAV/FLAC files)

Song title/Artist Album name/Artist Folder name

File name Playing time Clock Song title/Artist with

music synchronisation*

(backtothebeginning)

iPod FRONT/iPod REAR/ iPod USB/iPod BT

ANDROID FRONT/ ANDROID REAR/ANDROID

When

[HEAD MODE]/[AUTO MODE]

is selected

( 9)

Song title (Artist)

Song title (Album name) Song title (Date/Clock)

Playing time

(Date/Clock)

Song title (Artist) with music synchronisation*2 (backtothebeginning)

When

[HEAD MODE]/[AUTO MODE]

is selected

( 9)

Song title/Artist

Album name/Artist Playing time

Clock

Song title/Artist with music synchronisation*2

(backtothebeginning)

, :

( 35)

JS_JVC_KD_R995BTS_K_EN_03.indd 34JS_JVC_KD_R995BTS_K_EN_03.indd 34 7/6/2017 8:41:04 AM7/6/2017 8:41:04 AM

Page 35

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

REFERENCES

Source name

Display information

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS KD-R792BT/KD-R790BT/KD-RD79BT

PANDORA FRONT/ PANDORA REAR/PANDORA/ PANDORA BT

Station name (Date/Clock)

Shared/Radio (Date/Clock)

Song title (Artist) Song title

(Album name)

Song title (Date/Clock)

Playing time (Date/Clock)

Station name

(Date) with music synchronisation*

(back to the beginning)

Station name

Shared/Radio Song title Artist name

Album name

Playing time Clock Station name with music

synchronisation*

(back to the beginning)

IHEARTRADIO-F/ IHEARTRADIO-R/ IHEARTRADIO

Station name (Date/Clock)

Song title (Artist) Song title (Date/Clock)

Station name

(Date) with music synchronisation*

(back to the beginning)

Station name

Song title/Artist Clock Station name with

music synchronisation*

(back to the beginning)

SPOTIFY FRONT/ SPOTIFY REAR/SPOTIFY/ SPOTIFY BT

Context title (Date/Clock)

Song title (Artist) Song title (Album name) Song

title (Date/Clock)

Playing Time (Date/Clock)

Context title (Date) with music

synchronisation*

(back to the beginning)

Context title

Song title Artist name Album name

Playing Time Clock Context title with music

synchronisation*

(back to the beginning)

SIRIUS XM

Channel number (Status) Channel name (Status) Artist (Status) Song title (Status) Content information (Status)

Category name (Status) Date (Status) Channel number

(Status) with music synchronisation*

(back to the beginning)

—

BT AUDIO

Song title (Artist) Song title (Album name) Song title (Date/Clock)

Playing time

(Date/Clock)

Song title (Artist) with music synchronisation*2 (back to the beginning)

Song title/Artist

Album name/Artist Playing time Clock

Song title/Artist with music synchronisation*2 (back to the

beginning)

AUX

AUX (Date/Clock)

AUX (Date) with music synchronisation*2 (back to the beginning) AUX Clock AUX with music synchronisation*2 (back to

the beginning)

Battery and signal strength of the Bluetooth device will be shown if

[BATT/SIGNAL]

is set to

[AUTO]. ( 19)

For

KD-R995BTS/KD-R990BTS/ KD-R895BTS/KD-RD99BTS/KD-R99MBS

: The color of the button illumination changes and synchronises with the music.

For

KD-R792BT/KD-R790BT/KD-RD79BT

: The brightness of the button illumination changes and synchronises with the music.

JS_JVC_KD_R995BTS_K_EN_03.indd 35JS_JVC_KD_R995BTS_K_EN_03.indd 35 7/6/2017 8:41:10 AM7/6/2017 8:41:10 AM

Page 36

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Symptom Remedy

General

Sound cannot be heard. • Adjust the volume to the optimum level.

• Check the cords and connections.

“MISWIRING CHECK WIRING THEN PWR ON” appears.

Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.

“PROTECTING SEND SERVICE” appears.

Send the unit to the nearest service center.

Source cannot be selected. Check the

[SOURCE SELECT]

setting.

( 4)

“ERROR”/ “FAIL” (For

KD-R792BT

)

Your steering remote controller is not compatible, learning may not be completed. Consult your car audio dealer for details.

Radio

• Radio reception is poor.

• Static noise while listening to the radio.

Connect the antenna firmly.

CD/USB/iPod

Disc cannot be ejected.

Press and hold

to forcibly eject the disc. Be careful

not to drop the disc when it is ejected.

“IN DISC” appears. Make sure nothing is blocking the loading slot when

you eject the disc.

“PLEASE EJECT” appears.

Press

, then insert the disc correctly.

Playback order is not as intended.

The playback order is determined by the file name (USB) or the order in which files were recorded (disc).

Elapsed playing time is not correct.

This depends on the recording process earlier.

“NOT SUPPORT” appears and track skips.

Check whether the track is a playable format.

( 32, 33)

“READING” keeps flashing. • Do not use too many hierarchical levels and folders.

• Reload the disc or reattach the USB device.

TROUBLESHOOTING

Symptom Remedy

CD/USB/iPod

“UNSUPPORTED DEVICE” appears.

• Check whether the connected device is compatible with this unit and ensure the file systems are in supported formats.

( 32, 33)

• Reattach the device.

“UNRESPONSIVE DEVICE” appears.

Make sure the device is not malfunction and reattach the device.

“USB HUB IS NOT SUPPORTED” appears.

This unit cannot support a USB device connected via a USB hub.

“CANNOT PLAY” appears. Connect a USB device that contains playable audio files.

• The source does not change to “USB” when you connect a USB device while listening to another source.

• “USB ERROR” appears

The USB port is drawing more power than the design limit. Turn the power off and unplug the USB device. Then, turn on the power and reattach the USB device. If this does not solve the problem, turn the power off and on (or reset the unit) before replacing with another USB device.

The iPod/iPhone does not turn on or does not work.

• Check the connection between this unit and iPod/ iPhone.

• Disconnect and reset the iPod/iPhone using hard reset.

“LOADING” appears when you enter search mode by pressing

This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later.

Correct characters are not displayed.

• This unit can only display uppercase letters, numbers, and a limited number of symbols.

• Depending on the display language you have selected

( 5)

, some characters may not be displayed

correctly.

JS_JVC_KD_R995BTS_K_EN_03.indd 36JS_JVC_KD_R995BTS_K_EN_03.indd 36 7/6/2017 8:41:17 AM7/6/2017 8:41:17 AM

Page 37

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

TROUBLESHOOTING

Symptom Remedy

Pandora

“UPGRADEAPP” Make sure you have installed the latest version of the

Pandora application on your device.

“CONNECT ERR” Communication is unstable.

“RATING ERR” Registration of thumbs up/thumbs down has failed due

to insufficient network connectivity.

“THUMBS N/A” Registration of thumbs up/thumbs down is not allowed.

“LICENSE ERR” You try to access from a country which Pandora is not

deliverable.

iHeartRadio

Station cannot be selected. If “Explicit Content” in [Account Settings] is checked

in the web version of iHeartRADIO, custom stations become unavailable.

“NOT CONNCTD” Link to the application is impossible.

Spotify

“DISCONNECTED” USB is disconnected from the head unit. Please make

sure the device is connected properly through USB.

“CONNECTING” • Connected via USB input terminal: The device is

connecting to the head unit. Please wait.

• Connected via Bluetooth: The Bluetooth is disconnected. Please check Bluetooth connection and make sure both the device and unit are paired and connected.

“CHECK APP” The Spotify application is not connected properly or

user is not login. End the Spotify application and restart. Then, log in to your Spotify account.

SiriusXM® Radio

“CHLOCKED LOCK CODE?” The selected channel is locked. Enter the correct pass

code to unlock.

( 15)

“CHANUNSUB”

The selected channel is unsubscribed.

Symptom Remedy

ANDROID

• Sound cannot be heard during playback.

• Sound output only from the Android device.

• Reconnect the Android device.

• If in

[AUDIO MODE]

, launch any media player application

on the Android device and start playback.

• If in

[AUDIO MODE]

, relaunch the current media player

application or use another media player application.

• Restart the Android device.

• If this does not solve the problem, the connected Android device is unable to route the audio signal to unit.

( 33)

Cannot playback at

[AUTO MODE]

• Make sure JVC MUSIC PLAY APP is installed on the Android device.

( 8)

• Reconnect the Android device and select the appropriate control mode.

( 9)

• If this does not solve the problem, the connected Android device does not support

[AUTO MODE]. ( 33)

“NO DEVICE” or “READING” keeps flashing.

• Switch off the developer options on the Android device.

• Reconnect the Android device.

• If this does not solve the problem, the connected Android device does not support

[AUTO MODE]. ( 33)

Playback is intermittent or sound skips.

Turn off the power saving mode on the Android device.

“CANNOT PLAY” • Make sure Android device contains playable audio files.

• Reconnect the Android device.

• Restart the Android device.

Pandora

“ADDERROR” New station creation is unsuccessful.

“CHKDEVICE” Check the Pandora application on your device.

“NOSKIPS” The skip limit has been reached.

“NOSTATIONS” No stations are found.

“STATIONLMT” The number of registered stations has reached its limit.

Retry after deleting unnecessary stations from your device.

JS_JVC_KD_R995BTS_K_EN_03.indd 37JS_JVC_KD_R995BTS_K_EN_03.indd 37 7/6/2017 8:41:18 AM7/6/2017 8:41:18 AM

Page 38

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Symptom Remedy

Bluetooth®

Sound is being interrupted or skipped during playback of a Bluetooth audio player.

• Reduce the distance between the unit and the Bluetooth audio player.

• Turn off, then turn on the unit and try to connect again.

• Other Bluetooth devices might be trying to connect to the unit.

The connected Bluetooth audio player cannot be controlled.

• Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP). (Refer to the instructions of your audio player.)

• Disconnect and connect the Bluetooth player again.

“PLEASE WAIT” The unit is preparing to use the Bluetooth function. If

the message does not disappear, turn off and turn on the unit, then connect the device again.

“NOT SUPPORT” The connected phone does not support Voice

Recognition feature.

“ERROR” Try the operation again. If “ERROR” appears again, check

if the device supports the function you have tried.

“H/W ERROR” Reset the unit and try the operation again. If “H/W

ERROR” appears again, consult your nearest service center.

“SWITCHING NG” The connected phones might not support phone

switching feature.

If you have any troubles, try the following:

1 Check TROUBLESHOOTING 2

Reset the unit

( 3)

TROUBLESHOOTING

Symptom Remedy

SiriusXM® Radio

“CHUNAVAIL”

The selected channel is unavailable.

“CHECKANTENNA” Check that the antenna and its connection are in good

condition.

“CHECKTUNER” Make sure the SiriusXM Vehicle Tuner is connected to

the unit.

“NOSIGNAL” Make sure the antenna is mounted outside the vehicle.

“SUBSCRIPTION UPDATED – PRESS ENTER TO CONTINUE.”

Your subscription is updated. Press the volume knob to continue.

“CODE ERROR” Make sure you have entered the correct pass code.

( 15)

“NO CONTENT” There is insufficient content to start TuneScan.

“SCAN CANCEL” TuneScan has been aborted.

Bluetooth®

No Bluetooth device is detected.

• Search from the Bluetooth device again.

• Reset the unit.

( 3)

Pairing cannot be made. • Make sure you have entered the same PIN code to both

the unit and Bluetooth device.

• Delete pairing information from both the unit and the Bluetooth device, then perform pairing again.

( 16)

Echo or noise occurs. • Adjust the microphone unit’s position.

( 16)

• Check the

[ECHO CANCEL]

setting.

( 18)

Phone sound quality is poor.

• Reduce the distance between the unit and the Bluetooth device.

• Move the car to a place where you can get a better signal reception.

JS_JVC_KD_R995BTS_K_EN_03.indd 38JS_JVC_KD_R995BTS_K_EN_03.indd 38 7/6/2017 8:41:19 AM7/6/2017 8:41:19 AM

Page 39

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

SPECIFICATIONS

Tuner

FM Frequency Range 87.9MHz — 107.9MHz (200kHz step)

87.5MHz — 108.0MHz (50kHz step) Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω) Quieting Sensitivity (DINS/N=46dB) 17.2dBf (2.0μV/75Ω) Frequency Response (±3dB) 30Hz — 15kHz Signal-to-Noise Ratio (MONO) 64dB Stereo Separation (1kHz) 40dB

AM Frequency Range 530kHz — 1700kHz (10kHz step)

531kHz — 1611kHz (9kHz step)

Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)

CD player

Laser Diode GaAIAs Digital Filter (D/A) 8 times over sampling Spindle Speed 500 rpm — 200 rpm (CLV) Wow & Flutter Below measurable limit

Frequency Response (±1dB) 20Hz — 20kHz

Total Harmonic Distortion (1 kHz) 0.01 % Signal-to-Noise Ratio (1 kHz) 105dB Dynamic Range 90dB Channel Separation 85dB MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.aac” files

USB

USB Standard USB1.1, USB2.0 (Full speed) Compatible Devices Mass storage class File System FAT12/16/32 Maximum Supply Current DC5V

1.5A Digital Filter (D/A) Converter 24Bit Frequency Response (±1dB) 20Hz — 20kHz

Signal-to-Noise Ratio (1 kHz) 105dB Dynamic Range 90dB Channel Separation 85dB MP3 Decode Compliant with MPEG-1/2 Audio Layer-3 WMA Decode Compliant with Windows Media Audio AAC Decode AAC-LC “.aac”, “.m4a” files WAV Decode Linear-PCM FLAC Decode FLAC file, up to 24bit/96kHz

Auxiliary

Frequency Response (±3dB) 20Hz—20kHz

Input Maximum Voltage 1000mV Input Impedance 30kΩ

Bluetooth

Version Bluetooth 3.0 Frequency Range 2.402 GHz — 2.480 GHz Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2 Maximum Communication Range Line of sight approx. 10 m (32.8 ft) Pairing SSP (Secure Simple Pairing) Profile HFP1.6 (Hands-Free Profile)

A2DP (Advanced Audio Distribution Profile) AVRCP1.5 (Audio/Video Remote Control Profile) PBAP (Phonebook Access Profile) SPP (Serial Port Profile)

JS_JVC_KD_R995BTS_K_EN_03.indd 39JS_JVC_KD_R995BTS_K_EN_03.indd 39 7/6/2017 10:54:16 AM7/6/2017 10:54:16 AM

Page 40

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Warning

• The unit can only be used with a 12V DC power supply, negative ground.

• Disconnect the battery’s negative terminal before wiring and mounting.

• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire (black) to prevent a short circuit.

• To prevent short circuit: – Insulate unconnected wires with vinyl tape. – Be sure to ground this unit to the car’s chassis again after installation. – Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into

contact with metal parts to protect the wires.

Caution

• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.

• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.

• Do not connect the

wires of speakers to the car chassis or Ground wire (black), or connect

them in parallel.

• Connect speakers with a maximum power of more than 50W. If the maximum power of

the speakers is lower than 50W, change the

[AMP GAIN]

setting to avoid damaging the

speakers.

( 25)

• Mount the unit at an angle of less than 30º.

• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.

• Keep all cables away from heat dissipate metal parts.

• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.

• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.

INSTALLATION/CONNECTION

Audio

Maximum Output Power 50W×4 or

50W×2 + 50W×1 (Subwoofer = 4Ω)

Full Bandwidth Power

(at less than 1% THD)

22W×4

Speaker Impedance 4Ω—8Ω Preout Level/Load (CD/USB)

KD-R995BTS

5000mV/10kΩ load

KD-R895BTS/KD-R99MBS

4000mV/10kΩ load

KD-R990BTS/KD-R792BT/KD-R790BT

KD-RD99BTS/KD-RD79BT

2500mV/10kΩ load

Preout Impedance ≤600Ω

General

Operating Voltage

(10.5V—16V allowable)

14.4V

Maximum Current Consumption 10A Operating Temperature Range –10°C — +60°C

Installation Size (W×H×D) 182mm×53mm×158mm

(7-3/16"×2-1/8"×6-1/4")

Net Weight (includes Trimplate, Mounting Sleeve)

1.2k

(2.7lbs)

Subject to change without notice.

SPECIFICATIONS

JS_JVC_KD_R995BTS_K_EN_03.indd 40JS_JVC_KD_R995BTS_K_EN_03.indd 40 7/6/2017 8:41:20 AM7/6/2017 8:41:20 AM

Page 41

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Installing the unit (in-dash mounting)

Part list for installation

Basic procedure

Remove the key from the ignition switch, then disconnect

the

terminal of the car battery.

Connect the wires properly.

See Wiring connection.

( 42)

Install the unit to your car.

See Installing the unit (in-dash mounting).

Connect the terminal of the car battery.

Press to turn on the power.

Detach the faceplate and reset the unit within 5 seconds.

( 3)

How to remove the unitWhen installing without the mounting sleeve

Remove the mounting sleeve and trim plate from the unit.

Align the holes in the unit (on both sides) with the

vehicle mounting bracket and secure the unit with screws (commercially available).

Use only the specified screws. Using wrong screws might

damage the unit.

Do the required wiring.

(42)

Bend the appropriate tabs to hold the sleeve firmly in place.

Hook on the top side

Orientate the trim plate as illustrated before fitting.

Dashboard of your car

(A)

Faceplate

(C)

Mounting sleeve

(B)

Trim plate

(D)

Wiring harness

(E)

Extraction key

INSTALLATION/CONNECTION

JS_JVC_KD_R995BTS_K_EN_03.indd 41JS_JVC_KD_R995BTS_K_EN_03.indd 41 7/6/2017 8:41:20 AM7/6/2017 8:41:20 AM

Page 42

ENGLISH

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Car fuse block

Ignition switch

Light blue/yellow

Blue/white: To amplifier

Blue: To power antenna

Make this connection if your vehicle factory wiring

harness does not have “12V ignition switch” wire.

Separate red wire

Wiring connection

To the steering wheel

remote control adapter

Fuse (10A)Antenna terminal

Factory wiring

harness (vehicle)

Black: Ground

Yellow: Battery 12V

White: Front speaker/3-way crossover: Mid range speaker (left) White/black

Gray: Front speaker/3-way crossover: Mid range speaker (right) Gray/black

Purple: Rear speaker/3-way crossover: Tweeter (right) Purple/black

Join the same color wires together.

Red: Ignition 12V

Orange/white: Illumination

Blue/white: Remote (12 V

350mA)

Brown (not used)

Green: Rear speaker *

/3-way crossover: Tweeter (left)

Green/black *

You can also connect a subwoofer speaker directly using

this lead without an external subwoofer amplifier. For setting,

Custom wiring harness (separately purchased)

Vehicle

dashboard

Recommended connection

INSTALLATION/CONNECTION

IMPORTANT

We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer.

JS_JVC_KD_R995BTS_K_EN_03.indd 42JS_JVC_KD_R995BTS_K_EN_03.indd 42 7/6/2017 8:41:22 AM7/6/2017 8:41:22 AM

Page 43

Data Size: B6L (182 mm x 128 mm) Book Size: B6L (182 mm x 128 mm)

Connecting external components

INSTALLATION/CONNECTION

Connecting external amplifiers

KD-R995BTS/ KD-R895BTS/ KD-R99MBS

KD-R990BTS/ KD-R792BT/ KD-RD99BTS

KD-R790BT/ KD-RD79BT

JVC Amplifier

Remote wire (not supplied)

Signal cord (not supplied)

To remote lead (blue/white) of the wiring harness.

( 42)

Firmly connect the ground wire of the amplifier to the car’s chassis to avoid damaging the

unit.

Output terminals

KD-R792BT/KD-R790BT/KD-RD79BT:

Microphone input jack

( 16)

KD-R792BT

: Learning steering remote

( 31)

KD-R995BTS

: USB cable (DC 5 V 1.5 A) (approx. 1.2 m/4 feet)

KD-R995BTS/KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

MIC (Microphone input terminal)

( 16)

KD-R995BTS

KD-R990BTS/KD-R895BTS/KD-RD99BTS/KD-R99MBS

Expansion port (12 V

500mA) To the optional SiriusXM Vehicle Tuner

(commercially available)

( 13)

Output terminals 2-way crossover setting 3-way crossover setting

REAR : FRONT : SW :

Rear output Front output Subwoofer output

Tweeter output Mid Range output Woofer output

FRONT : REAR/SW :

Front output Rear/subwoofer output

Mid Range output Woofer output

REAR/SW : Rear/subwoofer output Woofer output

JS_JVC_KD_R995BTS_K_EN_03.indd 43JS_JVC_KD_R995BTS_K_EN_03.indd 43 7/6/2017 8:41:22 AM7/6/2017 8:41:22 AM

Learn more about car stereos we have.