JVC KD-R741BTE User Manual

KD-R841BT / KD-R741BT

ENGLISH

FRANÇAIS

CD RECEIVER

INSTRUCTION MANUAL

RÉCEPTEUR CD

MANUEL D’INSTRUCTIONS

Please read all instructions carefully before operation to obtain the best possible performance from the unit.

Veuillez lires les instructions attentivement avant d’utiliser l’appareil afin d’obtenir les meilleures performances possibles de l’appareil.

GET0844-001B [E/EN/EU]

Information on Disposal of Old Electrical and Electronic Equipment and Batteries (applicable for EU countries that have adopted separate waste collection systems)

Products and batteries with the symbol (crossed-out wheeled bin) cannot be disposed as household waste. Old electrical and electronic equipment and batteries should be recycled at a facility capable of handling these items and their waste byproducts. Contact your local authority for details in locating a recycle facility nearest to you. Proper recycling and waste disposal will help conserve resources whilst preventing detrimental effects on our health and the environment. Notice: The sign “Pb” below the symbol for batteries indicates that this battery

contains lead.

Information sur l’élimination des anciens équipements électriques et électroniques et piles électriques (applicable dans les pays de l’Union Européenne qui ont adopté des systèmes de collecte sélective)

Les produits et piles électriques sur lesquels le pictogramme (poubelle barrée) est apposé ne peuvent pas être éliminés comme ordures ménagères. Les anciens équipements électriques et électroniques et piles électriques doivent être recyclés sur des sites capables de traiter ces produits et leurs déchets. Contactez vos autorités locales pour connaître le site de recyclage le plus proche. Un recyclage adapté et l’élimination des déchets aideront à conserver les ressources et à nous préserver des leurs effets nocifs sur notre santé et sur l’environnement. Remarque: Le symbole “Pb“ ci-dessous sur des piles électrique indique que cette

pile contient du plomb.

The marking of products using lasers

The label is attached to the chassis/case and says that the component uses laser beams that have been classified as Class 1. It means that the unit is utilizing laser beams that are of a weaker class. There is no danger of hazardous radiation outside the unit.

Marquage des produits utilisant un laser

L’étiquette est attachée au châssis/boîtier de l’appareil et indique que l’appareil utilise des rayons laser de classe 1. Cela signifie que l’appareil utilise des rayons laser d’une classe faible. Il n’y a pas de danger de radiation accidentelle hors de l’appareil.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

• “Made for iPod,” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod, or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPod, or iPhone may affect wireless performance.

• iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

• Android is trademark of Google Inc.

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVC KENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.

CONTENTS

BEFORE USE

BEFORE USE 2

BASICS 3

GETTING STARTED 4

RADIO 5

AUX 6

CD / USB / iPod 7

ILLUMINATION

(

KD-R841BT

only)

BLUETOOTH® 9

AUDIO SETTINGS 14

MORE INFORMATION 15

TROUBLESHOOTING 16

SPECIFICATIONS 17

INSTALLATION / CONNECTION 18

How to read this manual

• Operations explained mainly using buttons on the faceplate of

• [XX] indicates the selected items.

•

(➜ XX)

indicates references are available on

the stated page number.

KD-R741BT

Warning

Do not operate any function that takes your attention away from safe driving.

Caution

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to prevent accident.

• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.

General:

• Avoid using the USB device or iPod/iPhone if it might hinder driving safety.

• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short circuit.

• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.

• USB rating is indicated on the main unit. To view, detach the faceplate. (

Remote control (RM-RK52):

• Do not leave the remote control in hot places such as on the dashboard.

• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.

• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

• Keep battery out of reach of children and in original package until ready to use. Dispose of used batteries promptly. If swallowed, contact a physician immediately.

KD-R741BT

only)

Maintenance

Cleaning the unit: Wipe off dirt on the faceplate with a dry silicon or soft cloth. Cleaning the connector: Detach the faceplate and clean the connector with a

cotton swab gently, being careful not to damage the connector.

Handling discs:

• Do not touch the recording surface of the disc.

• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.

• Do not use any accessories for the disc.

• Clean from the center of the disc and move outward.

• Clean the disc with a dry silicon or soft cloth. Do not use any solvents.

• When removing discs from this unit, pull them out horizontally.

• Remove burrs from the center hole and disc edge before inserting a disc.

Connector (on the reverse side of the faceplate)

BASICS

Faceplate

KD-R841BT

Volume knob

(turn/press) Loading slot

Display window

Attach

Remote control (RM-RK52)

(Need to purchase separately)

Remote sensor (Do not expose to bright sunlight.)

Detach

KD-R741BT

Pull out the insulation sheet

How to reset

Your preset adjustments will

Detach button

To Do this (on the faceplate) Do this (on the remote control)

Turn on the power Press and hold L SOURCE.

Adjust the volume Turn the volume knob. Press VOL + or VOL –.

Select a source • Press L SOURCE repeatedly.

Change the display information

• Press and hold to turn off the power.

Press the volume knob to mute the sound or pause playback.

• Press again to cancel.

• Press L SOURCE, then turn the volume knob within 2 seconds.

Press DISP repeatedly.

• Press and hold to scroll the current display information.

(➜ 15)

also be erased.

( not available )

Press

• Press again to cancel.

Press SOURCE repeatedly.

( not available )

when using for the first time.

How to replace the battery

to mute the sound or pause playback.

ENGLISH

GETTING STARTED

Cancel the demonstration

Press and hold

Press the volume knob to select

Turn the volume knob to select

Press

Set the clock

Press and hold

Turn the volume knob to select

Turn the volume knob to select the day, then press the knob.

Turn the volume knob to adjust the hour, then press the knob.

Turn the volume knob to adjust the minute, then press the knob.

Turn the volume knob to select

Turn the volume knob to select the knob.

Press

Set the basic settings

Press and hold

Turn the volume knob to make a selection (see the following table), then press the knob.

Press

To return to the previous hierarchy, press G

CLOCK

24H/12H CLOCK ADJ

to exit.

24 HOUR/ 12 HOUR: Selects the clock format. AUTO: The clock time is automatically set using the Clock Time (CT)

data in FM Radio Data System signal. ; OFF: Cancels.

[DEMO]

[DEMO OFF]

[CLOCK] [CLOCK SET]

[24H/12H] [24 HOUR]

, then press the knob.

, then press the knob. or

T/P

[12 HOUR]

then press

Default:

CLOCK

CLOCK DISP

DIMMER

DIMMER SET

BRIGHTNESS Sets the display and button brightness for day and night separately.

DISPLAY

SCROLL

TAG DISPLAY

(

KD-R841BT

USB *

DRIVECHANGE Selects to change the drive when a multiple drives device is connected to the USB input

IPOD SWITCH

HEAD MODE: Controls music playback only from this unit. ; IPOD MODE: Controls music playback from both the unit and iPod/iPhone. ; EXT MODE: Controls music playback only from the iPod/iPhone.

AUDIOBOOKS

NORMAL / FASTER / SLOWER: Selects the playback speed of the Audiobooks sound file in your iPod/iPhone.

(Default:

SRC SELECT

AUX

The illumination control wire connection is required. (➜

Some characters or symbols will not be shown correctly (or will be blanked).

Displayed only when the source is USB FRONT or USB REAR.

Displayed only when the source is USB-IPOD.

Not displayed when the corresponding source is selected.

ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels.

Selects the display and button illumination adjusted in the [BRIGHTNESS] setting. AUTO: Changes between the day and night adjustments when you turn off or on the car headlights. *

1 2

ONCE: Scrolls the display information once. ; AUTO: Repeats scrolling at 5-second intervals. ; OFF: Cancels.

ON: Shows the TAG information while playing MP3/WMA/WAV files. ; OFF: Cancels. only)

terminal (front/rear).

*4 (

KD-R841BT

Depends on your iPod/iPhone setting.)

ON: Enables AM in source selection. ; OFF: Disables. ON: Enables AUX in source selection. ; OFF: Disables.

; ON: Selects the night adjustments. ; OFF: Selects the day adjustments.

DAY/ NIGHT: Select day or night. Select the zone for setting.

KD-R841BT KD-R741BT

Set the brightness level (00 to 31).

Default: KD-R841BT

: BTN ZONE 1/ 2/ 3 / DISP ZONE / VOL ZONE (➜ 8) : BUTTON ZONE / DISP ZONE

KD-R741BT

only)

: DAY: 31 ; NIGHT: 11 : BUTTON ZONE: DAY: 25 ; NIGHT: 09

DISP ZONE: DAY: 31 ; NIGHT: 12

19)

Default:

RADIO

“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Search for a station

1 Press L SOURCE to select FM or AM. 2 Press E / F (or 2 / 3 on RM-RK52) to search for a station automatically. (or) Press and hold E / F (or 2 / 3 on RM-RK52) until “M” flashes, then press

repeatedly to search for a station manually.

Store a station

You can store up to 18 stations for FM and 6 stations for AM.

While listening to a station....

Press and hold one of the number buttons (1 to 6) to store.

(or) 1 Press and hold the volume knob until “PRESET MODE” flashes. 2 Turn the volume knob to select a preset number, then press the knob. The preset number flashes and “MEMORY” appears.

Select a stored station

Press one of the number buttons (1 to 6).

(or) 1 Press MENU. 2 Turn the volume knob to select a preset number, then press the knob.

Search for your favorite program (PTY Search)

Available only for FM Radio Data System stations.

1 Press and hold G 2 Turn the volume knob to select a PTY code (➜

T/P.

), then press the knob.

If there is a station broadcasting a program of the same PTY code as you have

selected, that station is tuned in.

Activate TA Standby Reception

Available only for FM Radio Data System stations.

T/P.

Press G

The unit will temporarily switch to Traffic Announcement (TA) (if available) from any source other than AM.

• To deactivate, press G T/P again.

Other settings

1 Press and hold MENU. 2 Turn the volume knob to select

[TUNER]

, then press the knob.

3 Turn the volume knob to make a selection (see the following table), then

press the knob.

4 Press MENU to exit.

Default:

SSM SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18: Automatically presets up to 18

AF-REG

NEWS-STBY

P-SEARCH

* Only for FM Radio Data System stations.

stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select SSM 07 – 12 / SSM 13 – 18 to store the following 12 stations.

AF ON: Automatically searches for another station broadcasting the same program in the same Radio Data System network with better reception when the current reception is poor. ; AF-REG ON: Switches to another station only in the specific region using the AF control. ; AF OFF: Cancels.

Displayed only when the source is FM.

ON: The unit will temporarily switch to News Programme if available. ; OFF: Cancels.

ON: When the signal of a preset station you have selected is weak, this unit searches for another station possibly broadcasting the same programme as the original preset station is broadcasting. ; OFF: Cancels.

ENGLISH

MONO Displayed only when the source is FM.

IF BAND

MONO ON: Improves the FM reception, but the stereo effect will be lost. ; MONO OFF: Cancels.

AUTO: Increases the tuner selectivity to reduce interference noises from adjacent stations. (Stereo effect

may be lost.) ; WIDE: Subjects to interference noises from adjacent stations, but sound quality will not be degraded and the stereo effect will remain.

Default:

AUXRADIO

Use a portable audio player

1 Connect a portable audio player (commercially available).

3.5 mm stereo mini plug with “L” shaped connector (commercially available)

RADIO TIMER

PTY code:

NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M

(music)

SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M DOCUMENT

Turns on the radio at a specific time regardless of the current source.

ONCE/ DAILY/ WEEKLY/ OFF: Select how often the timer will be turned on.

FM/ AM: Select the FM or AM band.

01 to 18 (for FM)/ 01 to 06 (for AM): Select the preset station.

Set the activation day and time.

• “M” lights up when complete. Radio Timer will not activate for the following cases.

• The unit is turned off.

• [OFF] is selected for [AM] in [SRC SELECT] after Radio Timer for AM is selected. (➜ 4)

, EASY M

(music)

, LIGHT M

(music)

, CLASSICS, OTHER M

(music)

, WEATHER, FINANCE, CHILDREN,

(music)

, ROCK M

, OLDIES, FOLK M

(music)

Auxiliary input jack

2 Select

[ON]

for

[AUX]

Portable audio player

[SRC SELECT]. (➜ 4)

3 Press L SOURCE to select AUX. 4 Turn on the portable audio player and start playback.

Use a 3-core plug head stereo mini plug for optimum audio output.

CD / USB / iPod

Start playback

Label side

The source changes to CD and playback starts.

• To eject a disc, press 0.

USB

USB input terminal

USB 2.0 cable

(commercially available)

and/ or

USB cable from the rear of the unit (KD-R841BT only)

The source changes to USB FRONT, USB REAR or USB and playback starts.

iPod/iPhone

USB input terminal

USB 2.0 cable* (accessory of the

iPod/iPhone)

and/ or

USB cable from the rear of the unit (KD-R841BT only)

The source changes to playback starts (for

USB-IPOD

KD-R841BT

and

: depending

on the status of the connected device). Press 4 iPod MODE repeatedly to select the

control mode (

[EXT MODE]

• See also

[HEAD MODE]

) directly.

[IPOD SWITCH]. (➜ 4)

[IPOD MODE]

Note: WAV files are playable only for

KD-R841BT

in USB source.

: Applicable

— : Not applicable

To Do this CD USB iPod

Select a track/file Press E / F (or 2 / 3 on RM-RK52).

Select a folder

Press 1 ∞ / 2 5 (or 5 / ∞ on RM-RK52).

(MP3/WMA/WAV)

Reverse/Fast-forward Press and hold E / F (or 2 / 3 on RM-RK52).

Select a track/file from a list

1 Press MENU 2 Turn the volume knob to make a selection, then press the knob.

• MP3/WMA/WAV file: Select the desired folder, then a file.

• iPod or JVC Playlist Creator (JPC) / JVC Music Control (JMC) file*3: Select the desired file from the list (PLAYLISTS, ARTISTS, ALBUMS, SONGS, PODCASTS*4, GENRES, COMPOSERS*4, AUDIOBOOKS*5).

• To return to the previous hierarchy, press G T/P.

• To cancel, press MENU.

Note: Turn the volume knob quickly to fast-search or use

Character search (➜

Repeat play Press 6 B repeatedly to make a selection.

• Audio CD or JPC / JMC file: TRACK RPT, RPT OFF

• MP3/WMA/WAV file: TRACK RPT, FOLDER RPT, RPT OFF

• iPod: ONE RPT, ALL RPT

Random play Press 5 A repeatedly to make a selection.

• Audio CD: ALL RND, RND OFF

• MP3/WMA/WAV file or JPC / JMC file: FOLDER RND, ALL RND, RND OFF

• iPod: SONG RND, ALBUM RND

Do not leave the cable inside the car when not using.

Applicable under

Only for files registered in the database created with JPC / JMC. (➜

Only for iPod.

[HEAD MODE]

and

[IPOD MODE]

only. (➜

, RND OFF

KD-R841BT

Applicable under

Not applicable for some iPod/iPhone.

15)

only.

[HEAD MODE]

only. (➜

ENGLISH

—

CD / USB / iPod

Character search

KD-R841BT

( If you have many folders or tracks/files, you can search through them quickly according to the first character (A to Z, 0 to 9 and OTHERS).

• “OTHERS” appear if the first character is other than A to Z, 0 to 9.

1 Press MENU . 2 For iPod: Turn the volume knob to select the

For MP3/WMA/WAV: Go to step 3.

3 Press 1 ∞ / 2 5 to select the desired character. 4 Turn the volume knob to select the desired folder

only)

desired list, then press the knob.

or track/file, then press the knob.

ILLUMINATION

(

KD-R841BT

only)

1 Press and hold MENU. 2 Turn the volume knob to select

[COLOR]

[COLOR SETUP]

, then press the knob.

3 Turn the volume knob to make a selection (see the following table), then press the knob. 4 Press MENU to exit.

COLOR

: Select a color for each zone separately.

BTN ZONE 1 / BTN ZONE 2 / BTN ZONE 3 / DISP ZONE / VOL ZONE / ALL ZONE: Select a zone.

COLOR 01 to COLOR 29: Select a color.

USER: Select a user color (created in [COLOR SETUP]). COLOR FLOW 01 to COLOR FLOW 03: Select a color changes pattern/speed.

SPECTRUM / GROOVE / TECHNO / EMOTION / RELAX / NIGHTSWEEP: (Selectable only if [ALL ZONE] is selected in step 1.)

(Default: BTN ZONE 1 / BTN ZONE 2 / ALL ZONE: [06] ; BTN ZONE 3: [27] ; DISP ZONE: [01] ; VOL ZONE: [COLOR FLOW 02])

COLOR SETUP

DAY COLOR

NIGHT COLOR

COLOR GUIDE ON: Changes the display and buttons illumination to white when settings are performed on menu and list

[NIGHT COLOR]

: Store your own day and night colors for each zone separately.

BTN ZONE 1 / BTN ZONE 2 / BTN ZONE 3 / DISP ZONE / VOL ZONE: Select a zone.

RED / GREEN / BLUE: Select a primary color.

00 to 31: Select the level.

Repeat steps 2 and 3 for all the primary colors.

• Your setting is stored to [USER] in [COLOR].

• If [00] is selected for all primary colors for [DISP ZONE], nothing appears on the display.

search. ; OFF: Display and buttons illumination remain the same even in menu and list search operation.

[DAY COLOR]

is changed by turning on or off your car’s headlight.

Default:

BLUETOOTH®

You can operate Bluetooth devices using this unit.

Connect the microphone

MIC (Microphone input terminal)

Rear panel

If you turn off the unit or detach the control panel during a phone call conversation, the Bluetooth connection is disconnected. Continue the conversation using your mobile phone.

Supported Bluetooth profiles

• Hands-Free Profile (HFP 1.5)

• Object Push Profile (OPP 1.1)

• Phonebook Access Profile (PBAP 1.0)

• Advanced Audio Distribution Profile (A2DP 1.2)

• Audio/Video Remote Control Profile (AVRCP 1.3)

Microphone (supplied)

Secure using cord clamps (not supplied) if necessary.

Adjust the microphone angle

Pair a Bluetooth device

When connecting a Bluetooth device to the unit for the first time, perform pairing between the unit and the device. Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit.

Up to five devices can be registered (paired) in total.

•

A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time. This unit supports Secure Simple Pairing (SSP).

•

Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually. Refer to the instruction manual of the Bluetooth device for more information.

1 Press and hold L SOURCE to turn on the unit. 2 Search and select “JVC UNIT” on the Bluetooth device. “BT PAIRING” flashes on the display.

• For some Bluetooth devices, you may need to enter the Personal Identification Number (PIN)

code immediately after searching.

3 Perform (A) or (B) depending on what scrolls on the display.

• For some Bluetooth devices, pairing sequence may vary from the steps described below.

(A) “[Device Name]” ] “XXXXXX” ] “VOL – YES” ] “BACK – NO”

• “XXXXXX” is a 6-digit passkey randomly generated during each pairing. 1 Ensure that the passkey which appears on the unit and Bluetooth device is the same. 2 Press the volume knob to confirm the passkey. 3 Operate the Bluetooth device to confirm the passkey.

(B) “[Device Name]” ] “VOL – YES” ] “BACK – NO”

1 Press the volume knob to start pairing. 2 • If “PAIRING” ] “PIN 0000” scrolls on the display, enter the PIN code “0000” into the

Bluetooth device. (You can change to a desired PIN code before pairing. (➜

13)

)

• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.

“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when Bluetooth connection is established.

• “ ” will light up when a Bluetooth mobile phone is connected.

• “ ” will light up when a Bluetooth audio player is connected.

See page 12 for Bluetooth compatibility check mode operation.

9 ENGLISH

BLUETOOTH®

Bluetooth mobile phone

To Do this

Receive a call

KD-R841BT KD-R741BT

On RM-RK52: Press 5 / ∞ / 2 / 3 / SOURCE.

Reject an incoming call

• When

[AUTO ANSWER]

unit answers incoming call automatically. (➜

KD-R841BT

G T/P. (Red area)

KD-R741BT

On RM-RK52: Press and hold 5 / ∞ / 2 / 3 / SOURCE.

End a call

Press and hold or the volume knob. On RM-RK52: Press and hold 5 / ∞ / 2 / 3 / SOURCE.

KD-R841BT

Receiving a call Talking

Flashes in green Lights up in red

: Press the volume knob. (Green area) : Press or the volume knob.

is set to the selected time, the

11)

: Press / L SOURCE / MENU / E / F /

: Press and hold or the volume knob.

After ending a

call

To Do this

Activate or deactivate hands-free mode

Adjust the phone volume

Press the volume knob during a call.

• Operations may vary according to the connected

Bluetooth mobile phone.

Turn the volume knob during a call. Phone volume:

• This adjustment will not affect the volume of the

other sources.

Adjust the microphone’s sensitivity level

Set the echo cancellation delay time

Text message notification

Press 1 ∞ / 2 5 during a call. Sensitivity level:

Press E / F during a call. Delay time:

When the phone receives a text message, the

unit rings and “RCV MESSAGE” ] [Device name] appears.

•

[MSG NOTICE]

• You cannot read, edit, or send a message through

the unit.

• To clear the message, press any button.

Switch between two connected phones

• To enter 1st phone’s hands-free menu: Press .

• To enter 2nd phone’s hands-free menu: Press twice.

• To return to 1st phone’s hands-free menu: Press G

[00]

[01]

must be set to

T/P.

[10]

[50]

(Default:

[03]

(Default:

[ON]. (➜ 11)

[15]

)

[02]) (➜ 11)

[04]) (➜ 11)

Flashes in red Return to [COLOR]

setting’s color (

➜

Return to [COLOR] setting’s color (➜ 8)

+ 28 hidden pages