Jensen VX7020 Installation Manual

VX7020

6.2” Double DIN Multimedia Receiver

DVD / NAV / SiriusXM-Ready®/ Built-in Bluetooth / Pandora Link
Compatible with iPhone /Compatible with iPod / USB / Aux In

INSTALLATION GUIDE

What’s in the Box

The following items are supplied with
the VX7020:

• VX7020 Head Unit

• Trim Ring

• Hardware Bag

• Power/Speaker Output Harness

• Remote Control

• External Microphone

• GPS Antenna

• Owners Manual & Warranty Card

• Installation Guide

WARNING! Never install this unit where operation and viewing could interfere with
safe driving conditions.

The following tools and supplies are
needed to install the VX7020:

• Torx type,  at-head and Philips

• Wire cutters and strippers

• Tools to remove existing radio (screw

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Tools and Supplies

screwdrivers

driver, socket wrench set or other
tools)

Optional Equipment

• Steering Wheel Control (SWC)- The VX7020 is SWC ready for vehicles equipped with the option. See wiring diagram for
installation details. For SWC programming details, please see the operation manual.

• Rear Camera- The VX7020 is Rear Camera ready for vehicles equipped with the option. See wiring diagram for installation
details.

Disconnect the Battery

• To prevent a short circuit, be sure to turn o the ignition and remove the negative (-) battery cable prior to installation.

NOTE: If the VX7020 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the
battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution
during installation to avoid causing a short circuit.

Replacing the Fuse

• When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating
could damage the unit and cause a  re.

ISO-DIN Installation

The VX7020 is designed to  t into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may be
used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount
the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation.

1. Remove the existing factory radio from the dashboard or
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.

2. Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.

CAUTION! Do not exceed M5 X 6MM screw size. Longer screws
may damage components inside the chassis.

3. Place the radio in front of the dashboard opening so the wiring

can be brought through the mounting sleeve. Follow the
wiring diagram carefully and make certain all connections are
secure and insulated with wire nuts or electrical tape. After
completing the wiring connections, plug the ISO connectors
into the mating sockets on the rear of the chassis. Turn the
unit on to con rm operation (vehicle ignition switch must be
“ON”). If the unit does not operate, re-check all wiring until the
problem is corrected.

4. Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.

CAUTION! Be careful not to damage the car wiring.

NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal laws.
The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.

Using the Cosmetic Trim Ring

A cosmetic trim ring is supplied with the head unit for installation
 exibility. This unit will  t into most import dashes with little or no
modi cation to the dash board/cavity. Some US domestic vehicle
dashes will accept a Double-DIN chassis, but there is usually a
small gap between the radio and dash piece after installation is
complete. In this case, use the trim ring to conceal any gaps that
may be present.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the unit is
mounted within this limitation.

1

Wiring Diagram

CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully,
or have the installation handled by an experienced technician.

Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815.

The VX7020 has a built-in SWC Interface compatible with most resistive type OE steering wheel controls. In most installations, only two of the three wires will be needed to

interface the OE steering wheel controls to the VX7020.

SWC A - Primary SWC Wire

SWC B - Secondary SWC Wire

SWC Ground - Chassis ground

Initial wiring of the SWC interface should include the SWC A and SWC Ground wire. If this combination of wiring does not support your vehicle functions, then try the SWC B

and SWC Ground wire combination. Do not use only SWC A and SWC B. The SWC Ground must be connected.

Some vehicles may not support all SWC functions.

Professional Installation is recommended.

Black/SiriusXM

Black/MICROPHONE

BT Antenna

SWC (BLACK)

GREEN/WHITE

WHITE/PURPLE

WHITE/BROWN

REVERSE

KEY A

KEY B

KEY GNDBROWN/BLACK

BLACK

YELLOW

RED

PINK

BLUE

GREEN/BLACK

GREEN

ORANGE

GROUND

BATTERY 12V (+)

BRAKE

POWER ANT & AMP. CONT

LEFT REAR SPEAKER (-)

LEFT REAR SPEAKER (+)

ILLUMINATION

ACC / IGNITION

)

WHITE/BLACK

WHITE

GRAY/BLACK

GRAY

PURPLE/BLACK

PURPLE

LEFT FRONT SPEAKER (-)

LEFT FRONT SPEAKER (+)

RIGHT FRONT SPEAKER (-)

RIGHT FRONT SPEAKER (+)

RIGHT REAR SPEAKER (-)

RIGHT REAR SPEAKER (+)

SPEAKER (-)

SPEAKER (+)

2

NOTES:

3

Installation Guide

Voxx Electronics Corporation

Hauppauge, NY 11788

Technical Assistance: 1-800-323-4815

www.jensenmobile.com

© 2014

Printed in China

128-9293