Installation Guide
Instruccionnes de Instalación
Instructions d’installation
Para obtener instrucciones en Español, diríjase a la página 5. Pour des instructions en Francais, référez-vous à la page 9.
VM9114
Multimedia Receiver
VM9114
160 Watts
What’s in the Box
VM9114 Head Unit
Single DIN Sleeve
Wiring Harness
Parking Brake Sensor Extension Wire
Mounting Hardware
3.5mm to 3.5mm Media Adaptor Cable
Cosmetic Trim Ring
Owners Manual
Installation Guide
Tools and Supplies
You will need these tools and supplies to install your VM9114:
• Torx type, fl at-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
A/V
INPUT
EJECT
WARNING! Never install this unit where operation and viewing could interfere with safe driving
conditions.
1
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the VM9114 is to be installed in a car equipped with an on-board drive or navigation computer, do
not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Pre-installation
Remove the four screws that attach the mounting sleeve to the
1
radio and remove the sleeve.
Install the mounting sleeve.
2
a. Install mounting sleeve into the dashboard or optional
adapter. Do not force the sleeve into the opening or cause
it to bend or bow.
b. Locate the series of bend-tabs along the top, bottom and
sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs
outward as necessary so that the sleeve is fi rmly secured
to the dashboard.
c. Install support strap to make the unit more stable.
EJECT
A
/
V
INPU
T
Place the radio in front of the dashboard opening so the wiring
3
can be brought through the mounting sleeve.
CAUTION! Be careful not to damage the car wiring.
TAB
TAB
DASHBOARD
DASHBOARD
2
Wiring
WARNING! Only connect the unit to a 12-volt power supply with proper grounding.
Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The
VM9114 uses one 15 amp fuse, located in the black fi lter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to confi rm operation (ignition switch must be on). If
unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off
the ignition switch and proceed with fi nal mounting of the chassis.
Connect wiring adapter to existing wiring harness.
1
Connect antenna lead.
2
Carefully slide the radio into the mounting sleeve, making
3
sure it is right-side-up, and secure with the original 4 screws.
Attach one end of the perforated support strap (supplied) to
4
the screw stud, which is screwed into the threaded insert on
the back of the unit, using the hex nut provided. Fasten the
other end of the perforated strap to a secure part of the
dashboard either above or below the radio using the screw
and hex nut provided. Bend the strap to position it as
necessary.
Replace any items you removed from the dashboard.
5
ISO-DIN Installation
Remove mounting sleeve brackets.
1
Remove trim ring.
2
Mount factory brackets on new radio using existing screws
3
from old radio.
Slide radio chassis into dash opening and secure.
4
Re-install dash panel.
5
EJECT
A
/
V
INPUT
CAUTION! The rear of the radio must be
supported with the strap to prevent damage to the dashboard from the weight of
the radio or improper operation due to
vibration.
NOTE: For proper operation of the CD/
DVD player, the chassis must be mounted
within 20° of horizontal. Make sure the unit
is mounted within this limitation.
EJECT
A
/
V
INPUT
Remove Mounting
Sleeve Brackets
EJECT
A
/
V
INPUT
3
Wiring Diagram
IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or
have the installation handled by an experienced technician.
REAR R
REAR L
PRK SW
PINK
PARKING BRAKE
Harness Cord
BLUE
ANT.CONT
BLUE/WHITE
P.CONT
BROWN
MUTE
External Power Amplifier
Antenna Jack
Antenna
Auto antenna control (connect to antenna
control lead & power supply of antenna
External power amplifier control
Mute (leave open if not connected)
amplifier)
Car Phone
Car
Ignition Switch
BATTERY +
Battery
Ground
ACC
FUSE (15A)
BATTERY
RED
ACC
YELLOW
BATT
BLACK
GND
Need Help?
For technical assistance, call the Jensen
customer support line at 1-800-323-4815.
WHITE +
WHITE/BLACK -
GREY +
GREY/BLACK -
PURPLE +
PURPLE/BLACK -
GREEN +
GREEN/BLACK -
FRONT L
FRONT R
REAR R
REAR L
4
Loading...