Quick Start Guide
An easy step-by-step guide to using the iRobot Scooba
www.irobot.com
Instructional videos available at www.irobot.com/usetips
Understand how iRobot Scooba cleans
Before You Get Started
Scooba’s Cleaning Pattern
Scooba is a robot that cleans differently than
the way most people clean their floors. Scooba
uses iRobot’s AWARE™ Robot Intelligence
System to determine the best way to pass
over and clean every section of the floor.
While Scooba is cleaning, it calculates the best
path to clean your floor and it determines the best
times to exhibit its various cleaning behaviors:
Spiraling: Enables Scooba to efficiently clean a
concentrated dirty area
Wall following: Enables Scooba to clean the room
perimeter and navigate around furniture and
obstacles
Room crossing: Enables Scooba to clean new
areas while crisscrossing the room
IMPORTANT:
Let Scooba complete an entire
cleaning cycle every time you clean
Scooba’s Cleaning System
Scooba performs 4 cleaning methods in one pass:
Preps – Picks up loose crumbs, sand, and dirt
Washes – Uses fresh, clean solution
Scrubs – Gently scrubs your floor, removing
dirt, grime, and spills
Dries – Picks up the dirty solution, leaving the
floor clean and dry*
* Floor drying time may vary.
Grasp the handle
and pull Scooba’s
tank up.
Release Scooba’s
tank by pushing
the handle.
1
2
Scooba’s Cleaning Pattern
SINK
STOVE
FRIDGE
TABLE
START
Internal Dry Mode
At the end of the cleaning cycle, Scooba will
enter a brief internal drying mode to remove
any liquid remaining on its brushes and inside
its cleaning mechanisms. During this time
Scooba’s Clean light will blink blue.
Charge Scooba’s Battery
Instructional videos available at www.irobot.com/usetips
Slowly fill the remainder of the Clean
tank with warm or cold tap water. Tilt
the tank and ensure it is completely
filled to the top.
4
Secure the tank cap and place
the tank back in the tank holder.
5
Open Scooba’s tank.
1
Lift the tank clear of the robot and
place the tank on a flat surface.
2
Close the tank by pressing
down on the tank. You will
hear a click when the tank
is properly installed.
6
Fill Scooba’s Tank
Place battery in Scooba by rotating
the battery into its slot, making
sure the yellow tabs fit inside the
guide holes.
3
3
Using the included measuring
cup, measure and pour Clorox®
Scooba cleaning solution into
the Clean tank.
3
4
Plug the Power Supply into Scooba
to charge the battery. For best
performance, iRobot recommends
charging Scooba's battery
overnight the first time only.
Power Button Light
Red
Green pulse
Green fast pulse
Solid Green
Blinking Red
Battery Status
Battery empty
Charging
16-hour refresh charge
Fully charged
Battery not installed
Use of plain tap water or extremely small amounts of cleaning solution reduces Scooba’s ability to
recognize water in the Clean tank. Always use the recommended amount of cleaning solution and water.
3
When Scooba has completed a cleaning cycle,
empty and rinse Scooba’s tanks.
Empty Scooba
5
Remove and clean Scooba's
cleaning head and brush.
6
Replace Scooba’s tank.
Clean With Scooba
With the Clean tank filled and properly installed, place
Scooba in the center of the room, press “Power” and
then press “Clean.” Scooba will begin a cleaning cycle.
Let Scooba clean until the tank is empty (approximately 45
minutes). Scooba’s “Clean” button will display the following:
© 2006 iRobot Corporation, 63 South Avenue, Burlington, MA 01803. All rights reser ved. iRobot is a registered trademark of iRobot Corporation. Scooba is a trademark of
iRobot Corporation. US Pat. Nos. 6,690,134 | 6,809,490 | 6,594,844. Other patents pending. Clorox is a registered trademark of The Clorox Company. All rights reserved.
See the Owner’s Manual for important tips and maintenance
instructions, or visit www.irobot.com
Open the Dirty and Clean
tanks and drain.
2
Remove Scooba’s tank.
1
Rinse the Dirty and Clean
tanks with warm water.
3
Clean Button Light
Green
Blue/Green pulse
Solid blue
What it means
Cleaning
Almost complete
Complete
Remove and rinse Scooba’s
filter.
4
Loading...