Hisense HASR09A, HASC09A, HASR12A, HASC12A, HASR24A User Manual
...
User Manual
Conventional Split Type Room Air Conditioner
HASR09A HASC09A
HASR12A HASC12A
HASR24A HASC24A
HASR30C HASC30C
Thank you very much for purchasing a 
air conditioner, please read this User Manual carefully before installing and using this appliance and keep this manual for future reference.
Contents
Preparation before use |
2 |
|
Safety Precautions |
3 |
|
Identification of parts |
|
|
Indoor unit |
4 |
|
Outdoor unit |
4 |
|
Operating and display |
5 |
|
|
||
Remote controller |
6 |
|
Operation instructions |
|
|
Operation modes |
8 |
|
Air flow direction control |
9 |
|
Smart mode |
10 |
|
Timer mode |
11 |
|
Sleep mode |
12 |
|
Super mode |
||
12 |
||
|
||
Maintenance |
13 |
|
Protection |
14 |
|
Troubleshooting |
15 |
|
Installation instructions |
|
|
Installation diagram of air conditioner |
16 |
|
Select the installation locations |
17 |
|
Indoor unit installation |
18 |
|
Outdoor unit installation |
23 |
|
Air purging |
23 |
|
Notes |
24 |
1
Preparation before use
Before using the air conditioner, be sure to check and preset the following.
Remote Controller presetting
The remote controller is NOT preset as Cooling Only Air Conditioner or Heat Pump by manufacturer.
Each time after the remote controller replaces batteries or is energized, the Cooling indicator |
and |
|
Heating indicator |
will flash alternately on the LCD of the remote controller. |
|
The user can preset the remote controller type depending on the air conditioner type you have purchased as follows:
Press any button when flashes, Heat Pump is set.
Press any button when 
flashes, Cooling Only is set.
If you don't press any button within 12 seconds, the remote controller is preset as Heat Pump automatically.
Note:
If the air conditioner you purchased is a Cooling Only, however you preset the remote controller as Heat Pump, it doesn't bring any matter. But if the air conditioner you purchased has a Heat Pump one, and you preset the remote controller as Cooling Only, then you CAN NOT preset the Heating operation with the remote controller.
Auto Restart Presetting
If you want auto restart function, hold down the Emergency button (ON/OFF) on the indoor unit until the appliance is energized.Auto restart function is set after the buzz sound three times.Air conditioner is on standby.
If auto restart has been set, hold down the Emergency button (ON/OFF) on the indoor unit until the appliance is energized. Auto restart function is cancelled after two buzzing sounds. Air conditioner is on standby.
2
Safety precautions
Symbols in this Use and Care Manual are interpreted as shown below.
Do not do.
The feature of the appliance, instead of a fault.
Pay attention to such a situation.
Be sure to follow this instruction.
Grounding is essential.
Warning: Incorrect handling could cause a serious hazard, such as death, serious injury, etc.
ON |
ON |
Use correct power supply in |
OFF |
|
|
OFF |
|||||||||||||||||
accordance with the rating plate |
|
|
|||||||||||||||||||
|
|
|
|
|
|
|
|
||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
requirement. Otherwise, serious |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
faults or hazard may occur or a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
fire maybe break out. |
Keep the power supply circuit breaker |
Do not use the power supply circuit |
|||||||||||||||||||
or plug from dirt. Connect the power |
|||||||||||||||||||||
|
|||||||||||||||||||||
|
breaker or pull off the plug to turn it off |
||||||||||||||||||||
|
supply cord to it firmly and correctly, |
||||||||||||||||||||
|
during operation. This may cause a fire |
||||||||||||||||||||
|
lest an electric shock or a fire break out |
||||||||||||||||||||
|
due to insufficient contact. |
due to spark, etc. |
|||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Do not knit, pull or press the power supply |
Never insert any obstacle's into the unit. |
It is harmful to your health if the cool air |
||
cord, lest the power supply cord be broken. |
||||
Since the fan rotates at high speed, this |
reaches you for a long time. It is advisable |
|||
An electric shock or fire is probably caused |
||||
by a broken power supply cord. |
may cause an injury. |
to let the air flow be deflected to all the room. |
||
|
ON |
|
|
|
|
OFF |
|
|
|
U |
RT |
|
|
|
S |
|
|
|
|
PE |
A |
|
|
|
R |
SM |
|
|
|
|
FAN |
|
|
|
ME |
G |
|
|
|
TI |
|
|
|
|
RO |
IN |
|
|
|
N |
SW |
|
|
|
|
T |
|
|
|
|
MIE |
|
|
|
|
RO |
|
|
|
|
FF |
|
|
|
|
CLOCK |
|
|
|
Turn off the appliance by remote control |
Do not attempt to repair the appliance. |
Prevent the air flow from reaching the gas |
||
firstly before cutting off the power supply |
Please call for a qualified service |
|||
burners and stove. |
||||
if malfunction occurs. |
technician. |
|||
|
||||
Do not touch the operation buttons when your hands are wet.
Do not place any objects on the outdoor unit.
It is the user's responsibility to make the appliance be grounded according to local codes or ordinances by a licenced technician.
3
Identification of parts
Indoor unit
US
ON
OFF 
REP
FAN
MODE
CL |
|
O |
P |
CK |
SLEE |
|
LOCK |
Outdoor unit
Air Intake
Front Panel
Display Panel
Emergency Button
Air Outlet
Vertical Adjustment
Louver
Horizontal Adjustment
Louver
Air Filter
Remote Controller
Air Intake
Pipes and Power
Connection Cord
Drain Hose
Note: Condensate water drains at COOLING or DRY operation.
Air Outlet
The figures in this manual are based on the external view of a standard model. Consequently, the shape may differ from that of the air conditioner you have selected.
The pipes and power connection cords will not be provided. They must be purchased by the customer.
4
Identification of parts
UP series operating and display
Timer Indicator Temperature Display Sleep Indicator
Lights up during the |
Display set temperature. |
Lights up when the |
|
set time. |
unit is in sleep mode. |
||
|
Compressor Indicator |
Signal Receptor |
Run Indicator |
It lights up when |
Receive signal from |
It is on during |
. |
the remote controller. |
operation. |
compressor is running. |
The shape and position of the switches and indicators may vary from different models, but their function are similar.
UL series operating and display
Timer Indicator Temperature display
Lights up during the |
Display set temperature. |
|
set time. |
||
Display trouble symbol.. |
Sleep indicator
Lights up when the sleep mode
.
is being set and within 10s after the sleep mode has been set.
Timer |
Comp. |
Run |
Sleep |
Compressor Indicator |
Signal Receptor |
It lights up when |
Receive signal from |
. |
the remote controller. |
compressor is running. |
Run Indicator
Is on during operation and flashes within 10s after the sleep mode has been set.
5
Remote controller
Remote controller
The remote controller transmits signals to the system.
1 ON/OFF BUTTON
The appliance will start turn on when energized or will turn off when it is in operation, if you press this button.
2MODE BUTTON
Press this button to select the operation mode.
3 |
FAN BUTTON |
|
|
Used to select fan speed in sequence |
|
|
auto, high, medium or low. |
4 |
4 |
5 ROOM TEMPERATURE |
3 |
|
SETTING BUTTONS |
|
|
|
|
|
Used to adjust the room temperature and |
|
|
the timer, also real time. |
|
6 |
SMART BUTTON |
13 |
|
Used to enter fuzzy logic operation directly, |
|
regardless if the unit is on or off. |
12 |
|
7SWING BUTTON
|
Used to stop or start vertical adjustment |
11 |
|
louver swinging and set the desired up/down |
|
|
airflow direction. |
10 |
8 |
SLEEP BUTTON |
|
|
Used to set or cancel Sleep Mode operation. |
|
9 |
LOCK BUTTON |
|
S
U
P
ER
FAN
TI
MER
ON
TIMER
OFF
CLOCK
When you press this button, all the buttons are locked and not available. Press again to cancel it.
1
ON
OFF
2
6
|
|
|
SMART |
7 |
MODE |
|
|
|
|
|
|
|
|
|
|
|
SW |
ING |
|
|
|
|
|
|
SL |
EEP |
|
|
5 |
|
|
|
|
|
K |
|
|
|
8 |
LOC |
|
|
|
|
|
|
|
|
9 |
10 CLOCK BUTTON
Used to set the current time.
11 12 TIMER ON/OFF BUTTON
Used to set or cancel the timer operation.
Indication symbols on LCD:
Cooling indicator |
|
Auto fan speed |
|
||
Dry indicator |
|
High fan speed |
Fan only indicator |
|
Medium fan speed |
Heating indicator |
|
Low fan speed |
13 SUPER BUTTON
Used to start or stop the fast cooling operation. (Fast cooling operates at high fan speed with 18 C set temp automatically )
Smart |
indicator |
|
Signal transmit. |
Sleep indicator |
ON |
Display set timer |
|
|
|
||
|
|
OFF |
Display current time |
Lock |
indicator |
|
|
|
|
||
Super |
indicator |
|
Display set temperature |
Note: Each mode and relevant function will be further specified in following pages.
6
Remote controller
Remote controller
How to Insert the Batteries
Remove the battery cover according to the arrow direction.
Insert new batteries making sure that the (+) and (-) of battery are matched correctly.
Reattach the cover by sliding it back into position.
Note:
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type when the display becomes dim.
If the replacement is done within 1 minute, the remote controller will keep original presetting. However, if you want to change the presetting from Heat Pump to Cool Only or Cool Only to Heat Pump, you should reload batteries 3 minutes after removing the old ones. (Please refer to page 1 for details.)
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
ON
OFF
ON
OFF
FAN
MODE
FAN
MODE
How to Use
To operate the room air conditioner, aim
the remote controller to the signal receptor. The remote controller will operate the air
conditioner at a distance of up to 7m when pointing at signal receptor of indoor unit.
Signal receptor
Choose Cooling Only Remote controller or Heat Pump
Please refer to page 1 " Preparation before use" for details.
7
Operation instructions
Operation modes
Selecting mode
Each time MODE button is pressed, the operation mode is changed in sequence:
COOLING 
DRY 
FAN ONLY 
HEATING
Heating mode is NOT available for cooling only air conditioner.
FAN mode
Each time the "FAN" button is pressed, the fan speed is changed in sequence:
Auto |
High |
Medium |
Low |
At "FAN ONLY" mode, only "High","Medium" and "Low" are available. At "DRY" mode, Fan speed is set at "Low" automatically, "FAN" button is ineffective in this case.
Setting temperature
Press once to raise temperature setting by 1
Press once to lower temperature setting by 1
Range of available set temperature
*HEATING, COOLING |
18 ~32 |
DRY |
unable to set |
FAN ONLY |
unable to set |
ON
OFF
S |
|
4 |
T |
UPER |
|
|
MAR |
|
|
S |
|
|
|
|
|
FAN |
|
MODE |
ING |
TIM |
|
|
|
ER |
|
|
1SW |
2 |
|
|
|
ON |
|
|
|
TIMER |
3 |
SLEEP |
|
OFF |
|
|
|
CLOCK |
LOCK |
|
|
*Note: Heating mode is NOT available for cooling only models.
Turning on
Press 
button, when the appliance receives the signal, the RUN indicator of the indoor unit lights up.
SWING, SMART, TIMER ON, TIMER OFF, CLOCK, SLEEP and SUPER operation modes will be specified in the following pages.
Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes.
During heating operation, air flow is not discharged at the beginning. After 2 5 minutes, the air flow will be discharged until temperature of indoor heat exchanger rises.
Wait 3 minutes before restarting the appliance.
8
Loading...