SETUP & OPERATION MANUAL
FEATURES
Horizontal or vertical cutting.
Automatic shut-off.
Chip brush and safety guard included.
Quick-adjust vise with full to 45º to 90º mitering.
Adjustable blade tension and guide bearings.
Adjustable hydraulic down feed control.
Coolant system with built-in tank and pump.
4-speed design.
7” X 12” METAL CUTTING BANDSAW
SPECIFICATIONS
• Cutting capacity at 90º (Rectangular)
7” x 12” (179 x 305 mm)
• Cutting capacity at 90º (Round)
7” (179 mm)
• Cutting capacity at 45º (Rectangular)
4” x 7” (102 x 178 mm)
• Cutting capacity at 45º (Round)
4” (102 mm)
• Blade size
3/4” x 0.035” x 93” (19 x 0.9 x 2360 mm)
• Blade speeds
86, 132, 178 & 260 fpm
• Base dimensions
51” x 20” (1295 x 508 mm)
• Overall dimensions
49 1/4” x 27 1/8” x 40 3/4” (1250 x 690 x 1035 mm)
• Motor (pre-wired 120 V)
1 HP, 120/240 V, 1 Ph, 9/4.5 A
• Weight
330 lbs (150 kg)
Version #2_Revision #1 - April 2015
© Copyright General International
MODEL
#
90-725
GENERAL® INTERNATIONAL
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Telephone (514) 326-1161 • Fax (514) 326-5555 • www.general.ca
THANK YOU
for choosing this General® International model 90-725 7” x
12” Metal Cutting Bandsaw. This bandsaw has been carefully tested and inspected before
shipment and if properly used and maintained, will provide you with years of reliable service.
For your safety, as well as to ensure optimum performance and trouble-free operation, and to
get the most from your investment, please take the time to read this manual before assembling,
installing and operating the unit.
The manual’s purpose is to familiarize you with the safe operation, basic function, and
features of this bandsaw as well as the set-up, maintenance and identification of its parts and
components. This manual is not intended as a substitute for formal metalworking instruction,
nor to offer the user instruction in the craft of metalworking. If you are not sure about the safety
of performing a certain operation or procedure, do not proceed until you can confirm, from
knowledgeable and qualified sources, that it is safe to do so.
Once you’ve read through these instructions, keep this manual handy for future reference.
DISCLAIMER: The information and specifications
in this manual pertain to the unit as it was supplied
from the factory at the time of printing. Because we
are committed to making constant improvements,
General® International reserves the right to make
changes to components, parts or features of this unit
as deemed necessary, without prior notice and without
obligation to install any such changes on previously
delivered units. Reasonable care is taken at the factory
to ensure that the specifications and information in this
manual corresponds with that of the unit with which it
was supplied. However, special orders and “after factory”
modifications may render some or all information in
this manual inapplicable to your machine. Further,
as several generations of this model of Metal Cutting
Bandsaw and several versions of this manual may be
in circulation, if you own an earlier or later version of
this unit, this manual may not depict your unit exactly. If
you have any doubts or questions contact your retailer
or our support line with the model and serial number of
your unit for clarification.
GENERAL® INTERNATIONAL WARRANTY
All component parts of General® International and Excalibur by General International® products
are carefully inspected during all stages of production and each unit is thoroughly inspected upon
completion of assembly.
Limited Lifetime Warranty
Because of our commitment to quality and customer satisfaction, General® International agrees to
repair or replace any part or component which upon examination, proves to be defective in either
workmanship or material to the original purchaser for the life of the tool. However, the Limited Lifetime
Warranty does not cover any product used for professional or commercial production purposes nor
for industrial or educational applications. Such cases are covered by our Standard 2-year Limited
Warranty only. The Limited Lifetime Warranty is also subject to the “Conditions and Exceptions” as listed
below.
Standard 2-Year Limited Warranty
All products not covered by our lifetime warranty including products used in commercial, industrial
and educational applications are warranted for a period of 2 years (24 months) from the date of
purchase. General® International agrees to repair or replace any part or component which upon
examination, proves to be defective in either workmanship or material to the original purchaser during
this 2-year warranty period, subject to the “conditions and exceptions” as listed below.
To file a Claim
To file a claim under our Standard 2-year Limited Warranty or under our Limited Lifetime Warranty,
all defective parts, components or machinery must be returned freight or postage prepaid to
General® International, or to a nearby distributor, repair center or other location designated by
General® International. For further details call our service department at 1-888-949-1161 or your local
distributor for assistance when filing your claim.
Along with the return of the product being claimed for warranty, a copy of the original proof of purchase
and a “letter of claim” must be included (a warranty claim form can also be used and can be obtained,
upon request, from General® International or an authorized distributor) clearly stating the model and
serial number of the unit (if applicable) and including an explanation of the complaint or presumed
defect in material or workmanship.
CONDITIONS AND EXCEPTIONS:
This coverage is extended to the original purchaser only. Prior warranty registration is not required but
documented proof of purchase i.e. a copy of original sales invoice or receipt showing the date and
location of the purchase as well as the purchase price paid, must be provided at the time of claim.
Warranty does not include failures, breakage or defects deemed after inspection by
General® International to have been directly or indirectly caused by or resulting from; improper use,
or lack of or improper maintenance, misuse or abuse, negligence, accidents, damage in handling or
transport, or normal wear and tear of any generally considered consumable parts or components.
Repairs made without the written consent of General® International will void all warranty.
TABLE OF CONTENTS
Rules for safe operation ..................................................................................................... 5
Electrical requirements ...................................................................................................... 6
Identification of main parts and components .................................................................. 7
Unpacking .......................................................................................................................... 8
Basic functions ................................................................................................................... 8
Placement within the shop/Safety zone ............................................................................ 9
Placement within the shop ................................................................................................................................ 9
Establishing a safety zone .................................................................................................................................. 9
Assembly instructions ................................................................................................... 9-11
Installing the wheels ........................................................................................................................................... 9
Installing the pulley cover ................................................................................................................................10
Installing the workpiece stop .......................................................................................................................... 10
Installing the table for vertical cutting ............................................................................................................ 10
Install the coolant/recovery tray filter ............................................................................................................ 11
Basic adjustments and controls ................................................................................. 11-19
Connecting to a power source .......................................................................................................................11
Main On/Off power switch ...............................................................................................................................11
Overload protection ......................................................................................................................................... 12
Changing the blade ................................................................................................................................... 12-13
Adjusting blade tension ................................................................................................................................... 14
Adjusting blade tracking ............................................................................................................................ 14-15
Squaring the blade to the table work ............................................................................................................ 15
Squaring the vise to the table/using the vise ........................................................................................... 15-16
Adjusting the blade guides ............................................................................................................................. 16
Adjusting the thrust bearings ........................................................................................................................... 17
Adjusting the blade guards ............................................................................................................................. 17
Changing speeds ............................................................................................................................................. 17
Speed selection chart ...................................................................................................................................... 18
Cutting feed rate / saw arm tension .............................................................................................................. 18
Using the coolant pump .................................................................................................................................. 18
Immobilizing the machine .............................................................................................................................. 19
Operating Instructions ..................................................................................................... 18
Checklist before starting .................................................................................................................................. 19
Operations step-by-step ................................................................................................................................... 19
Maintenance .................................................................................................................... 20
Cleaning ............................................................................................................................................................ 20
Lubrication ......................................................................................................................................................... 20
Changing the belt/Aligning the pulleys ........................................................................................................ 20
Trouble shooting ......................................................................................................... 21-22
Parts list & diagram .................................................................................................... 23-29
Contact information ........................................................................................................ 30
RULES FOR SAFE OPERATION
To help ensure safe operation, please take a moment to learn the machine’s applications and limitations,
as well as potential hazards. General
harmless for any injury that may result from the improper use of it’s equipment.
1. Do not operate the bandsaw when tired, distracted
or under the effects of drugs, alcohol or any medI cation that impairs reflexes or alertness.
2. The work area should be well lit, clean and free
of debris.
3. Keep children and visitors at a safe distance when
the bandsaw is in operation; do not permit them to
operate the bandsaw.
4. Childproof and tamper proof your shop and all ma chinery with locks, master electrical switches and
switch keys, to prevent unauthorized or unsupervised
use.
5. STAY ALERT! Give your work your undivided attention.
Even a momentary distraction can lead to serious
injury.
6. Fine particulate dust is a carcinogen that can be
hazardous to health. Work in a well-ventilated area.
Wear face, eye, ear, respiratory and body protec tion devices.
7. Do not wear loose clothing, gloves, bracelets,
necklaces or other jewelry while the bandsaw is in
operation.
8. Be sure that adjusting wrenches, tools, drinks and
other clutter are removed from the machine and/or
the table surface before operating.
9. Keep hands well away from the blade and all
moving parts. Use a brush, not hands, to clear away
chips and dust.
10. Adjust and position the blade guides before starting
to cut.
11. Adjust blade tension and tracking before starting to
cut.
12. Blade teeth must point down toward the table.
13. Be sure that the blade has gained full operating
speed before starting to cut.
14. Always use a clean, properly sharpened blade.
Dirty or dull blades are unsafe and can lead to
accidents.
®
International disclaims any real or implied warranty and holds itself
15. Use suitable workpiece support if the workpiece
does not have a flat surface.
16. Make sure the workpiece is securely held in place
in the vise.
17. Do not work on long stock without adequate sup port on the out feed end of the table.
18. Do not push or force stock into the blade. The band saw will perform better and more safely when work ing at the rate for which it was designed.
19. Avoid working from awkward or off balance posi tions. Do not overreach and keep both feet on floor.
20. Keep guards in place and in working order. If a
guard must be removed for maintenance or clean ing be sure it is properly re-attached before using
the saw again.
21. Never leave the machine unattended while it is run- ning or with the power on.
22. Use of parts and accessories NOT recommended
by General
malfunction or risk of injury.
23. Never stand on machinery. Serious injury could re sult if the tool is tipped over or if the cutting tool is
unintentionally contacted.
24. Always disconnect the saw from the power
source before servicing or changing accessories
such as blades, or before performing any mainte nance or cleaning, or if the machine will be left
unattended.
25. Make sure that the switch is in the “OFF” position
before plugging in the power cord.
26. Make sure the machine is properly grounded. If
equipped with a 3-prong plug it should be used with
a three-pole receptacle. Never remove the third
prong.
27. Do not use this bandsaw for other than its intended
use. If used for other purposes,General® International
disclaims any real or implied warranty and holds it
self harmless for any injury, which may result from
that use.
®
International may result in equipment
5
ELECTRICAL REQUIREMENTS
BEFORE CONNECTING THE MACHINE TO THE POWER SOURCE, VERIFY THAT THE VOLTAGE OF YOUR POWER
SUPPLY CORRESPONDS WITH THE VOLTAGE SPECIFIED ON THE MOTOR I.D. NAMEPLATE. A POWER SOURCE
WITH GREATER VOLTAGE THAN NEEDED CAN RESULT IN SERIOUS INJURY TO THE USER AS WELL AS DAMAGE
TO THE MACHINE. IF IN DOUBT, CONTACT A QUALIFIED ELECTRICIAN BEFORE CONNECTING TO THE POWER
SOURCE.
THIS TOOL IS FOR INDOOR USE ONLY. DO NOT EXPOSE TO RAIN OR USE IN WET OR DAMP LOCATIONS.
A
B
GROUNDING INSTRUCTIONS
In the event of an electrical malfunction or short circuit,
grounding reduces the risk of electric shock. The motor
of this machine is wired for 120 V single phase operation and is equipped with a 3-conductor cord and a
3-prong grounding plug A to fit a grounded type receptacle B. Do not remove the 3rd prong (grounding pin)
to make it fit into an old 2-hole wall socket or extension
cord. If an adaptor plug is used C, it must be attached
to the metal screw of the receptacle.
Note: The use of an adaptor plug is illegal in some areas.
Check your local codes. If you have any doubts or if the
supplied plug does not correspond to your electrical outlet, consult a qualified electrician before proceeding.
CIRCUIT CAPACITY
Make sure that the wires in your circuit are capable of
handling the amperage draw from your machine, as
well as any other machines that could be operating on
the same circuit. If you are unsure, consult a qualified
electrician. If the circuit breaker trips or the fuse blows
regularly, your machine may be operating on a circuit
that is close to its amperage draw capacity. However,
if an unusual amperage draw does not exist and a
power failure still occurs, contact a qualified technician
or our service department.
C
CONVERTING THE MOTOR TO 240V
Note: When converting motor voltage on a machine that
is equipped with a magnetic switch, the switch contactor
must also be changed out for one made for the appropriate voltage, as well as the thermal relay/circuit breaker
and “power in” indicator light (if applicable). Failure to
make these necessary modifications to the switch will lead
to malfunction and permanent switch failure.
Should you need to convert your machine’s motor
from 120 V to 240 V power, contact a qualified electrician. Unless you are a qualified electrician, we do
not recommend attempting this conversion on your
own. If you choose to do so, you may risk serious personal injury, damage to the motor and voiding the
warranty of your machine. We suggest you ask your
local General International distributor to recommend
qualified electricians in your area (or perhaps one of
their own technicians) who can make this conversion
properly and safely.
EXTENSION CORDS
If you find it necessary to use an extension cord with
your machine, use only 3-wire extension cords that have
3-prong grounding plug and a matching 3-pole receptacle that accepts the tool’s plug. Repair or replace a
damaged extension cord or plug immediately. Make
sure the cord rating is suitable for the amperage listed
on the motor I.D. plate. An undersized cord will cause a
drop in line voltage resulting in loss of power and overheating. The accompanying chart shows the correct
size extension cord to be used based on cord length
and motor I.D. plate amp rating. If in doubt, use the next
heavier gauge. The smaller the number, the heavier the
gauge.
TABLE - MINIMUM GAUGE FOR CORD
EXTENSION CORD LENGTH
AMPERES 50 feet 100 feet 200 feet 300 feet
< 5
6 to 10
10 to 12
12 to 16
*NR = Not Recommended
18 16 16 14
18 16 14 12
16 16 14 12
14 12 *NR *NR
6
IDENTIFICATION OF MAIN PARTS AND COMPONENTS
R
F
E
A
T
S
I
B
O
J
C
D
H
L
U
V
P
N
G
Q
K
M
A. BLADE TENSIONING HANDLE
B. SAW ARM
C. VISE
D. VISE ADJUSTMENT HANDWHEEL
E. MAIN ON/OFF SWITCH
F. COOLANT PUMP SWITCH
G. WHEELS (4)
H. BLADE
I. GEAR BOX
J. MOTOR
K. WORKPIECE STOP
L. COOLANT RECOVERY TRAY
M. STAND
N. CYLINDER
O. BLADE GUIDES (2)
P. RECOVERY TRAY FILTER
Q. CYLINDER VALVE
R. BLADE TENSION INDICATOR
S. PULLEY COVER
T. EMERGENCY STOP BUTTON
U. CUT OFF LIMIT SWITCH
V. ELECTRICAL BOX
7
UNPACKING
Carefully unpack and remove the unit and its components from its shipping container and check for missing or
damaged items as per the list of contents below.
NOTE: PLEASE REPORT ANY DAMAGED OR MISSING ITEMS TO YOUR GENERAL® INTERNATIONAL DISTRIBUTOR IMMEDIATELY.
LIST OF CONTENTS QTY
A. PULLEY COVER ......................................................................... 1
B. COOLANT FILTER ...................................................................... 1
C. LOCK KNOB ............................................................................. 1
D. HEX HEAD BOLT ....................................................................... 2
E. WORKPIECE STOP .................................................................... 1
F. VERTICAL CUTTING TABLE ....................................................... 1
G. WHEEL ...................................................................................... 4
H. WHEEL AXLE ............................................................................. 2
I. STOP SHAFT .............................................................................. 1
J. COTTER PIN ............................................................................. 4
K. FLAT WHEEL WASHER ................................................................ 4
L. PULLEY COVER WASHER .......................................................... 2
ADDITIONAL REQUIREMENTS FOR SET UP
A
C
D E
B
A. EXTRA PERSON FOR HELP WITH LIFTING
B. PHILLIPS SCREWDRIVER
C. 10, 12,14 & 20 MM WRENCHES
D. 4 & 6 MM ALLEN KEYS
E. PLIERS
F. SQUARE
A
C
E
H
G
F
B
F
D
I
J
LK
BASIC FUNCTIONS
This 7” x 12” horizontal metal cutting band saw is designed for both vertical and horizontal cutting in metalworking
and machine shops for cutting various types of bar stock, channel stock, piping, and thin-walled tubing.
With four blade speeds to accommodate a wide range of cutting needs, the unit features an automatic hydraulically controlled down feed with auto shutoff at the end of the cutting cycle.
The coolant system with built-in pump is designed to supply a continuous flow of liquid coolant to the cutting area
to prevent overheating of both the blade and the workpiece, providing cleaner cuts and prolonging blade life.
8
PLACEMENT WITHIN THE SHOP / SAFETY ZONE
THIS MODEL 90-725 METAL CUTTING BANDSAW IS HEAVY. DO NOT OVER-EXERT. A HOIST OR FORKLIFT WITH STRAPS
SHOULD BE USED TO LIFT THIS MACHINE. TO LIMIT THE RISK OF SERIOUS INJURY OR DAMAGE TO THE MACHINE,
ANY EQUIPMENT USED TO LIFT THIS MACHINE SHOULD HAVE A RATED CAPACITY IN EXCESS OF 330 LBS (150 KG).
PLACEMENT WITHIN THE SHOP
This machine should be installed and operated only on
a solid, flat and stable floor that is able to support the
weight of the machine (330 lbs - 150 kg) and the operator. Using the dimensions shown as a guideline, plan for
placement within your shop that will allow the operator
to work unencumbered and unobstructed by foot traffic (either passing shop visitors or other shop workers) or
other tools or machinery.
ESTABLISHING A SAFETY ZONE
For shops with frequent visitors or multiple operators,
it is advisable to establish a safety zone around shop
machinery. A clearly defined “no-go” zone on the floor
around each machine can help avoid accidents that
could cause injury to either the operator or the shop
visitor.
It is advisable to take a few moments to either paint
(using non-slip paint) or using tape, define on the floor
the limits or perimeter of each machines safety zone.
Take steps to ensure that all operators and shop visitors are aware that these areas are off limits whenever
a machine is running for everyone but the individual
operating the unit.
50"
40"
16"
ASSEMBLY INSTRUCTIONS
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
TIP: TO INSTALL THE WHEELS, YOU WILL NEED TO LIFT THE MACHINE. DUE TO THE WEIGHT OF THE MACHINE, ADEQUATE LIFTING
EQUIPMENT SUCH AS A JACK, HOIST, OR FORKLIFT WITH STRAPS IS REQUIRED. ANY EQUIPMENT USED TO LIFT THE MACHINE MUST
HAVE A MINIMUM WEIGHT CAPACITY OF 330 LBS (150 KG).
INSTALLING THE WHEELS
1. At one end of the machine, install an axle A as
shown.
Note: The ends of the axle should protrude beyond the
sides of the machine.
2. Lift the machine and install the wheels on the ends
of the axle.
3. Slide a flat washer onto the axle and against each
wheel and then insert a cotter pin through the
holes on each end of the axle as shown B.
4. Fold down the prongs of the cotter pin as shown.
5. Repeat the previous steps with the other axle and
wheels.
A
B
9
BEFORE ASSEMBLING, MAKE SURE THAT THE SWITCH IS IN THE “OFF” POSITION AND THAT THE POWER CORD IS
UNPLUGGED. DO NOT PLUG IN OR TURN ON THE MACHINE UNTIL YOU HAVE COMPLETED THE ASSEMBLY AND
INSTALLATION STEPS DESCRIBED IN THIS SECTION OF THE MANUAL.
INSTALLING THE PULLEY COVER
A B
1. Slide the pulley cover behind the pulleys A and line
up its mounting holes with the corresponding holes
on the machine B.
INSTALLING THE WORKPIECE STOP
F
C
2. Attach the cover to the machine using a flat washer
and bolt C with a 10 mm wrench. Then screw the
lock knob in place D to keep the cover door closed
during operations.
G
H
D
E
1. Using a 12 mm wrench loosen bolt E without re-
moving it, then slide the stop bar all the way into its
mounting hole F and re-tighten the bolt to secure
the bar in place.
INSTALLING THE TABLE FOR VERTICAL CUTTING
I
1. To lock the blade arm in the UP position shut off the
hydraulic downfeed control valve I and lift the arm
into the vertical position.
2. Slide the workpiece stop onto the bar as shown G
and tighten the thumbscrew H to secure it in place.
K
J
2. Remove the screws on either side of the blade J.
Guide the table slot around the blade and line up
the holes in the table with the holes in the bracket
K. Secure the table to the bracket using the screws
removed in step 1.
10
INSTALL THE COOLANT SYSTEM/RECOVERY TRAY FILTER
The coolant system with built-in pump is designed to
supply a continuous flow of liquid coolant to the cutting area to prevent overheating of both the blade and
the workpiece, providing cleaner cuts and prolonging
blade life.
1. Fit the steel mesh filter A over the coolant recovery
tank drain B.
Note: To prolong the life of the pump and prevent blockages in the coolant system, remove and clean the filter regularly using a compressed air blow gun to remove metal
chips and other debris.
A
BASIC ADJUSTMENTS & CONTROLS
TO REDUCE THE RISK OF SHOCK OR FIRE DO NOT OPERATE THE UNIT WITH A DAMAGED POWER CORD OR PLUG. REPLACE DAMAGED CORD OR PLUG IMMEDIATELY. TO AVOID UNEXPECTED OR UNINTENTIONAL START-UP, MAKE SURE
THE POWER SWITCH IS IN THE OFF POSITION BEFORE CONNECTING TO A POWER SOURCE.
CONNECTING TO A POWER SOURCE
Once the assembly steps have been completed, plug
the power cord into an appropriate outlet.
Refer back to the section entitled “Electrical Require
ments” and make sure all requirements and grounding
instructions are followed. When operations have been
completed unplug the saw from the power source.
-
B
SWITCH OFF
TO AVOID UNEXPECTED OR UNINTENTIONAL
START-UP, MAKE SURE THAT THE POWER SWITCH
IS IN THE OFF POSITION BEFORE CONNECTING
TO A POWER SOURCE.
MAIN ON/OFF POWER SWITCH
This machine is equipped with a magnetic safety switch
designed to protect the unit and the user from power
surges, power outages and unwanted or unintentional
start-up.
The switch assembly is equipped with a green “start”
button A, a red “stop” button B and an emergency
stop button twist lock-out device C. Once this button
has been pressed, the machine can only be started
by turning the button to the right to release the stop
button, C.
The limit switch E on the end of the stand is designed to
make contact with the stop on the saw head to turn off
the machine automatically.
If necessary the position of the stop can be adjusted
loosening the bolt G with a 10 mm wrench and sliding
the stop right or left along its elongated slot. Once the
stop is adjusted to be able to turn off the machine F,
retighten the bolt G to secure the tab in place.
Switch D allows you to turn the coolant system pump
on or off. To start the pump, turn the switch to the right.
To stop the pump, turn the switch to the left.
C
D
B
A
E
G
F
11
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
OVERLOAD PROTECTION
The magnetic safety switch on this machine is equipped with an overload protection feature. To prevent an electrical overload from damaging the motor, in the event of a spike in line voltage or amperage draw, the internal
overload protector will automatically be tripped, thereby cutting off power to the motor.
Common causes of such overloads:
1. Overworking the motor by attempting to remove too much material in one single pass or by feeding the workpiece too quickly, thereby causing an increase in power consumption and a spike in amperage draw.
2. An electrical extension cord that is too long or not the correct gauge of wire, which can also cause an increase in amperage draw. If an electric extension cord must be used, follow the instructions and refer to the
chart in the electrical requirements section at the beginning of this manual.
3. Overworked circuit caused by operating on a circuit that is close to its amperage draw capacity. Make sure
the circuit being used is capable of handling the amperage draw from this machine as well as any other
electrical devices operating on the same circuit. If you are unsure, consult a qualified electrician.
To reset the overload protection switch after it has been tripped proceed as follows:
A
B
Loosen the bolt A with a 10 mm wrench and open the overload protection access door. Press on the button B to
reset the overload protection switch. Close the overload protection access door and retighten bolt A before restarting the machine.
Note: If the machine still does not work after resetting the overload protector, check all three fuses located inside the
electrical box and replace them as needed with matching amperage fuses.
CHANGING THE BLADE
There are a variety of different types of bandsaw blades on the market to suit various cutting applications. Your
results may vary based on usage, experience and personal preference. Ask your local tool dealer for suggestions
for bandsaw blades in 0.035” (0,9 mm) thickness and 3/4” (19 mm) width x 93” (2360 mm) length.
Note: Generally speaking, because one wheel height is somewhat adjustable (to allow for blade tensioning), a blade
length variation of plus or minus 1/2” from the “ideal blade length” can be accommodated.
The blades with fewer teeth per inch are best suited to cut quickly and aggressively but do have a tendency to
bind (or get stuck in the cut) if turned too sharply. Thinner blades with more teeth per inch will cut more slowly but
can cut with more precision.
Common causes of blade breakage:
• Poor blade guide or support bearing alignment and
adjustment.
• Dull teeth.
• Setting blade guard assembly too far from the work-
• Too much blade tension.
• Lumpy or improperly finished braze or weld on the
blade.
• Cutting feed rate too high.
piece.
12
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
INSTALLING A BLADE (CONTINUED)
A
B
1. Lift the arm into the vertical position. Loosen the lock
knob A and then push the guard down as shown.
Remove the two lock knobs B and open the blade
cover.
3. Remove the metal brush with a Phillips screwdriver
as shown.
WHEEL SHOULDER
SHOULDER
2. Loosen the blade by turning the tensioning handle
counterclockwise.
THE SAW BLADES ARE SHARP, HANDLE THEM CAREFULLY AND MAKE SURE YOU HAVE PROTECTIVE
GLOVES IF NECESSARY TO AVOID INJURY.
4. Carefully remove the blade from the wheels.
C
BLADE
BLADE
BLADE
WHEEL SHOULDER
BLADE
5. Install a new blade with the teeth towards you. To ten-
sion the blade, hold the blade against the shoulder
of the wheels as shown, and then turn the tension
handle.
Note: See section “Adusting blade tension”.
6. Re-install the metal brush positioning it along its
elongated mounting holes C, and close the blade
cover.
13
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
ADJUSTING BLADE TENSION
A properly tensioned blade is critical to obtaining maximum performance from any bandsaw. A properly tensioned blade will last longer and be much less likely to break prematurely.
If the blade tension is too loose you will notice that the blade will have a tendency to drift or slip off-line when
cutting and you will have more difficulty controlling your cuts. A blade that is tensioned too tightly will break prematurely.
The following information can be used as a guideline or starting point to assist you in determining ideal blade tension. This bandsaw is equipped with a blade tension scale, which can be used as a reference for the ideal tension
with various blade widths.
To adjust the blade tension
1. Lower the arm into the horizontal posi-
tion.
2. Turn the handle A clockwise to ten-
sion the blade or counterclockwise to
loosen. The white mark B shoud be centered in the shaded zone C of the tension indicator.
3. Make a test cut on a sample piece and
if needed, re-adjust the blade tension.
Note: To check the blade tension, apply gentle
finger pressure on the blade side facing you.
The blade should not move more than 0.004”.
C
A
B
A
ADJUSTING BLADE TRACKING
The upper wheel is aligned at the factory, but it may eventually be necessary to re-adjust the alignment after a
long period of use or after maintenance. This potential misalignment can be corrected by adjusting the tilt of the
upper wheel.
F
D
E
1. Shut off the hydraulic downfeed control valve and
lift the arm into the vertical position. Loosen lock
knob D and slide the blade guard down as shown.
Remove the two lock knobs E and open the blade
cover.
14
2. Loosen the two bolts F with a 14 mm wrench.
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
ADJUSTING BLADE TRACKING (CONTINUED)
3. Loosen the blade by turning the handwheel coun-
terclockwise.
SQUARING THE BLADE TO THE WORK TABLE
C
BLADE
BLADE
SHOULDER
A
BLADE
B
BLADE
4. Adjust the wheel tilt by turning the screw A with a 4
mm Allen key, so that the blade stays against the
shoulder of the pulley. Tighten two bolts B, close the
blade cover and tension the blade.
D
E
SQUARE
WORK TABLE
1. Lower the arm into the horizontal position and then
place a square against the vise face and against
the blade as shown E. If the blade is not square to
the table go to step 2.
SQUARE
WORK TABLE
2. Loosen screw D with a 6 mm Allen key and make
sure that the blade is parallel with the square by
turning the blade support E. Retighten screw D once
finished adjusting. Repeat with the second support
on the other side.
SQUARING THE VISE TO THE BLADE/USING THE VISE
The vise can accommodate workpieces up to 7" wide. Adjust the angle of cut or square the vise to the table as follows:
F
VISE JAW
VISE JAW
SQ
U
B
A
BL
L
RE
AD
A
DE
E
SQ
U
A
B
L
RE
A
D
E
1. Lower the arm into the horizontal position and place
a square against one of the jaws and the blade as
shown.
Note: The blade must be perfectly squared to the vise F. If
the blade is not squared, go to the next step.
15
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORM-
0,001"
0,001"
ING ANY MAINTENANCE OR ADJUSTMENTS.
SQUARING THE VISE TO THE BLADE/USING THE VISE (CONTINUED)
2. To adjust the left jaw, loosen bolts A and B using a
20 mm wrench.
3. Position the jaw to the desired angle, or squared to
the blade, and then tighten bolts A and B.
4. Repeat the previous steps with the right jaw using
the bolts C and D.
Note: Use the vise handwheel to open or close the vise.
A
A
B
D
C
ADJUSTING THE BLADE GUIDES
The guide bearings K keep the blade from moving from side to side during the cutting and must be adjusted
close to the blade (but not touching the blade) in order to ensure accurate cuts. The space between each guide
bearing and the blade must not exceed 0.001”. If less space is left, the blade will get stuck or jammed between the
bearings. Too much friction will cause the blade to overheat and break.
Note: Before adjusting the blade guides, make sure the blade is tensioned and tracking properly. Re-adjust the blade
guides after each blade tension or tracking adjustment.
LEFT SIDE
RIGHT SIDE
H
E
G
1. Loosen lock knobs E & F and push the two blade
guards G & H in the direction of thSe arrows. Shut
off the hydraulic downfeed control, and then lift the
arm into the vertical position.
F
K
J
I
2. Loosen nut I using a 14 mm wrench.
3. Turn the eccentric shaft J with pliers until the blade
and bearing are about 0.001” apart as shown K.
4. To lock the bearing position, retighten nut I while
holding shaft J with pliers. Repeat steps 2 to 4 for the
other bearing, and then for the second assembly
located on the other side of the saw arm.
5. Make a test cut and re-adjust the blade guides if
needed.
16
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
ADJUSTING THE THRUST BEARINGS
The thrust bearing keeps the blade from moving back and out of position when the saw arm pushes against the
workpiece. The thrust bearing must be very close to the back of the blade A to prevent damage to the blade during cutting. To adjust it, proceed as follows:
A
1. Shut off the hydraulic downfeed control valve and
lift the arm into the vertical position. Loosen screw B
on bracket C.
ADJUSTING THE BLADE GUARDS
The blade guards should be adjusted based the dimensions of the workpiece.
To prevent the blade (which is flexible and which would
not otherwise be supported) from slipping out of position during cutting, and to reduce risks of injuries, a
minimum amount of blade should be exposed.
For a straight cut and to reduce the risk of twisting, loosen lock knobs I & J and position the blade guards G &
H as close as possible to the workpiece, then retighten
the lock knobs.
D
E
1/32”
B
C
2. Push bracket C as shown D until the thrust bearing
touches the back of the blade A. Repeat for the
other thrust bearing.
Note: The blade guides must remain at least 1/32” behind
the blade teeth to prevent damage to the blade as shown E.
LEFT SIDE
I
G
RIGHT SIDE
H
J
CHANGING SPEEDS
1. Lower the arm into the horizontal position and loos-
en the jam nut and bolt K with a 12 mm wrench.
2. Loosen the jam nuts L and bolts M with a 12 mm
wrench until the base of the motor can move.
3. Open the pulley cover and change the speed (refer to the chart in the manual or the sticker inside
the pulley cover).
Note: if there is not enough slack to move the belt, loosen
tension bolts M as needed.
4. Retighten bolts M alternating until the belt tension
is properly adjusted, then secure the motor in position by tightening jam nuts L and jam nut and bolt
K. Close the pulley cover.
K
L
M
TIP: CHECK TENSION BY PUSHING THE BELT WITH YOUR FINGER. THE BELT SHOULD NOT MOVE MORE THAN 1/2”.
17
AA
B
C
D
AA
B
C
D
POULIE DE L’ARBRE
POULIE DU MOTEUR
SPINDLE PULLEY
MOTOR PULLEY
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
SPEED SELECTION CHART
BELT SPEED (fpm)
BLADE SPEEDS
A
B
C
D
260
178
132
86
CUTTING FEED RATE/ SAW ARM TENSION
A hydraulic cylinder allows adjustments to the downfeed speed of the arm to control cutting speed.
Note: The valve must be open in order to adjust the cutting feed rate.
A
VALVE OPENED
VALVE CLOSED
- Turn the knob A clockwise to increase the cutting
feed rate.
- Turn the knob A counterclockwise to reduce the
cutting feed rate.
Note: Forcing the blade into the workpiece increases the
risk of blade breakage and can affect the quality of the cut
(burrs, chips, etc.).
USING THE COOLANT PUMP
The switch A allows you to turn the coolant system pump
on or off. You can also stop the flow of the liquid coolant
by closing the valve B.
Make sure that the level of liquid coolant in the tanklocated under the work table is between 3 liters (minimum) and 5 liters (maximum).
Don’t start the pump during vertical cuts.
Note: To reduce the risk of blade breakage and obtain
cleaner cuts, always use the coolant system except for vertical cuts.
A tension spring helps lift the arm into the the vertical
position and slows down its descent. If too little tension
makes it difficult to raise the arm, proceed as follow:
1. Loosen the jam nut B and tighten bolt C a few turns.
2. Repeat as needed until the desired tension is
achieved and then retighten the jam nut B.
Note: For less tension, loosen bolt C.
A B
B C
VALVE OPENED
VALVE CLOSED
18
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
IMMOBILIZING THE MACHINE
Machine vibration during operation may cause the
machine to move, particularly when installed on uneven surfaces.
The bolt-down tab and anchor bolt A can be used to
help keep the machine immobilized by either lowering the bolt against the floor to act as another point of
contact with the floor, or for permanent installations, by
drilling into the floor and bolting the machine in place.
A
OPERATING INSTRUCTIONS
CHECKLIST BEFORE STARTING
VERIFY ALL CHECK POINTS BEFORE STARTING. FAILURE TO COMPLY CAN RESULT IN SERIOUS INJURIES.
1. Make sure you and any assistants are wearing safe and appropriate workshop attire.
2. To reduce the risk of damage to the machine, as well as potential for personal injury, after initial set-up as well
as before each use, make sure that everything is securely installed and that all fasteners and moving parts on
this machine are locked in place before starting the machine.
3. Make sure to have on safety glasses as well as hearing or/and respiratory protection at all times when using the
machine.
4. Check the level of coolant in the tank and fill it as necessary. The level should be between 3 liters (minimum)
and 5 liters (maximum).
5. Use only recommended parts and accessories. The use of parts or accessories NOT recommended by
GENERAL® INTERNATIONAL may result in a risk of injury or damage to the machine.
6.
Be sure that adjusting wrenches, tools, drinks and other clutter are removed from the machine and/or the
table surface before operating.
OPERATIONS STEP-BY-STEP
NEVER USE THE SAW WITHOUT ALL GUARDS AND COVERS IN PLACE BEFORE STARTING THE SAW. BE SURE THAT THE
BLADE IS NOT ALREADY IN CONTACT WITH THE WORKPIECE.
For horizontal cuts
1. Raise the saw arm by the handle and lock it in position by shutting off the hydraulic downfeed control valve.
2. Trace the cutting line on your workpiece with a pencil and clamp the material firmly in the vise to ensure a
straight cut through the material. Make sure the workpiece is properly secured in the vise. Refer to the chart
below for proper stock placement in the vise.
Note: Use the workpiece stop to make repeat cuts to the same length.
3. Adjust the blade guards as close as possible to the workpiece.
4. Start the machine.
5. Allow the blade to come to full speed, then begin the cut by opening the hydraulic downfeed control valve
and letting the head down slowly onto the workpiece. Re-adjust the cutting feed rate if needed.
Note: Do not drop or force the head onto the workpiece.
6. Wait for the automatic shutdown of the saw before carefully removing the workpiece from the vise.
BURN DANGER: DO NOT USE BARE HANDS TO TOUCH THE WORKPIECE AT THE CUT LOCATION UNTIL IT HAS COOLED.
19
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
MAINTENANCE
CLEANING
After using your bandsaw, sweep up and discard any
excess metal chips and debris. Follow this maintenance
schedule and refer to any specific instructions given in
this section.
Daily:
• Check for loose mounting bolts.
• Check the blade for damage.
• Check for worn or damaged electrical wires.
• Check for any other unsafe conditions.
• Clean the metal blade brush.
Monthly:
• Inspect V-belt tension, damage, or wear.
• Clean the vise screw with compressed air and lubricate as shown with an all-purpose oil.
LUBRICATION
Periodically clean the filter and the recovery tray. Fill
the tank so that the liquid coolant level is between 3
and 5 liters. Machine gears are mounted in an oil-bath.
You don’t need to fill it up, except in case of gear box
leak or overheating.
Change the oil once a year by replacing it with a
80W/90 oil as follows:
1. Remove bolts A with a 10 mm wrench and then re-
move the gear box cover to drain the gear box.
2. Re-install the cover and then remove plug B. Fill the
gear box with until it reaches the hole and then reinstall the plug B.
A
B
CHANGING THE BELT & ALIGNING THE PULLEYS
A
D
B
C
E
1. Lower the arm into the horizontal position and loosen the jam nut and bolt A with a 12 mm wrench.
2. Loosen jam nuts B and bolts C with a 12 mm wrench until the motor base can be moved.
3. Open the pulley cover and change the belt.
Note: If there is not enough slack to move the belt, loosen tension bolts C as needed.
4. Place a straight edge on the two pulleys to verify their alignment. If the pulleys are not aligned, loosen the four
bolts D and E located on the motor mounting plate, and then reposition the motor along the slotted mounting
holes so that the pulleys are aligned.
5. With the pulleys aligned, retighten the four bolts D and E.
6. Retighten the two bolts C alternating one turn at a time until the belt is tensioned properly. Then secure the
motor in position by tightening the jam nuts B and the jam nut and bolt A. Close the pulley cover.
Note: check the tension by pushing the belt with your finger. The belt should not move more than 1/2”.
20
TROUBLE SHOOTING
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
Workpiece loose in vise Tighten the vise
Incorrect feed speed Adjust feed speed
Blade teeth space too large Replace the blade
EXCESSIVE BLADE BREAKAGE
MOTOR OVERHEATING
Material too coarse Use a blade of slow speed and
Incorrect blade tension Tension the blade
Teeth in contact with workpiece before saw is turned on
Blade rubs on wheel flange Adjust wheel aliignment
Misaligned guide bearing Adjust guide bearing
Blade too thick Use thinner blade
Blade cracking at weld Weld again
Blade tension too high Reduce blade tension
Motor belt tension too high Reduce belt tension
Blade is too coarse for work Use finer blade
Blade is too thin to work Use thicker blade
improperly aligned gears
Binding blade Reduce feed pressure
Gears need lubrication Check oil level
Feed pressure too high Reduce feed pressure
small teeth spacing
Place the blade in contact with
blade after turning on the machine
Adjust gears so that worm is in center of gear
BAD CUT (CROOKED)
BAD CUT (ROUGH)
Guide bearings not adjusted Adjust guide bearings
Inadequate blade tension Tension the blade
Dull blade Replace the blade
Speed incorrect Adjust speed
Blade guide too far from blade Adjust guide spacing
Blade guide loosens Re-tighten lock knobs
Blade tracks too far from wheel
shoulder
Blade or feed speed too high Reduce blade or speed feed
Blade is too thick Replace with thinner blade
Blade tension insufficient Tension the blade
Binding blade Reduce feed pressure
Blade tension too high Reduce blade tension
Adjust blade tracking
2121
TROUBLE SHOOTING
MAKE SURE THE MACHINE HAS BEEN TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE OR ADJUSTMENTS.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
Blade teeth too coarse Use finer tooth blade
Speed too high Reduce speed
Feed pressure too high Reduce feed pressure with cylinder
PREMATURE BLADE DULLING
BLADE IS TWISTING
BROKEN TEETH
Hard spots or scale on material
Hardening of material
Blade twists
Insufficient blade tension Tension the blade
Blade slides Tension the blade
Bending blade Reduce feed pressure
Blade tension too high Reduce blade tension
Blade teeth too coarse Use finer tooth blade
Pressure too high or speed too slow Reduce pressure, increase speed
Vibrating workpiece Clamp the workpiece properly
Excessive chips
Reduce speed, increase feed pressure
Increase feed pressure by tightening the cylinder lock knob
Replace the blade and adjust its
tension
Use thicker tooth blade or brush regularly to remove chips
NOTES
22
DIAGRAM
23
DIAGRAM
24
PARTS LIST
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
PART # DESCRIPTION SPECIFICATIONS QTY
90725-01 RECOVERY TRAY 1
90725-02 LEFT SUPPORT 1
90725-03 RIGHT SUPPORT 1
90725-04 FRONT PANEL 1
90725-05 LOWER TRAY 1
90725-06 SWITCH BOX 1
90725-07 HEX HEAD BOLT 5
90725-08 TERMINAL STRIP 1
90725-09 TRANSFORMER 1
90725-10 MAGNETIC SWITCH 1
90725-13 HEX HEAD BOLT 5/16 X 3/4” 8
90725-14 LOCK WASHER 5/16” 8
90725-15 WASHER 5/16” 8
90725-16 LOCK WASHER 5/16” 8
90725-17 NUT 5/16” 8
90725-18 HEX HEAD BOLT 5/16” X 1/2” 6
90725-19 NUT 5/16” 6
90725-20 CYLINDER 1
90725-21 CAP SCREW M10 X 40 1
90725-22 WASHER 3/8” 1
90725-23 LOCK WASHER M10 1
90725-24 NUT M10 1
90725-25 HEX HEAD BOLT 3/8” X 1” 2
90725-26 LOCK WASHER 3/8” 2
90725-27 PIN 1
90725-28 SET SCREW 1/4” X 3/8” 1
90725-29 LOWER CYLINDER SUPPORT 1
90725-33 WASHER 5/8” 4
90725-34 WHEEL 5” 4
90725-35 WHEEL AXLE 2
90725-36 COTTER PIN 4
90725-38 ELECTRIC CORD ASSEMBLY 1
90725-39 TABLE 1
90725-40 HEX HEAD BOLT 5/16” X 1” 5
90725-41 WASHER 5/16” 5
90725-42 LOCK WASHER 5/16” 5
90725-43 NUT 5/16” 5
90725-44 FILTER 1
90725-45 SCREW 3/16” X 3/8” 2
90725-46 COVER 1
90725-46-1 SCREW 3/16” X 1/2” 2
90725-47 HANDWHEEL 1
90725-48 SET SCREW 5/16” X 3/8” 1
90725-49 KEY 5” X 20” 1
90725-50 LEAD SCREW 1
90725-51 NUT SEAT 1
90725-52 ACME NUT 1
90725-53 BUTTON 1
90725-54 RETAINER 1
90725-55 LOCK WASHER M5 1
25
PARTS LIST
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
PART # DESCRIPTION SPECIFICATIONS QTY
90725-56 SCREW M5 X 8 1
90725-57 HEX HEAD BOLT 5/16” X 5/8” 2
90725-58 LOCK WASHER 5/16” 2
90725-59 SUPPORT PLATE 1
90725-60 STOP PIN 1
90725-61 NUT 5/16” 2
90725-62 HEX HEAD BOLT 3/8” X 1” 1
90725-63 NUT 3/8” 1
90725-64 90° SUPPORT 1
90725-65 NUT 3/8” 2
90725-66 LOCK WASHER 3/8” 2
90725-67 LIMIT SWITCH 1
90725-68 LIMIT SWITCH PLATE 1
90725-69 SCREW 5/32” X 1” 2
90725-70 HEX HEAD BOLT 2
90725-71 HEX HEAD BOLT 5/16 X 3/4” 1
90725-72 THUMBSCREW 1
90725-73 WORKPIECE STOP 1
90725-74 STOP SHAFT 1
90725-75N NYLOCK 1/2” 2
90725-76 WASHER 1/2” 2
90725-78 RUBBER COVER 1
90725-79 WASHER 5/32” 2
90725-80N SUPPORT SHAFT 22 MM 1
90725-81 PIVOT ARM 1
90725-84 PLATE 1
90725-85 LOCK WASHER 3/8” 2
90725-86 HEX HEAD BOLT 3/8” X 1 1/2” 2
90725-87 SPRING 1
90725-88 SPRING ADJUSTING ROD 1
90725-89 SPRING BRACKET 1
90725-90 HEX HEAD BOLT 5/16” X 1” 1
90725-91 NUT 3/8” 2
90725-92 LOCK WASHER 5/16” 1
90725-93 NUT 5/16” 1
90725-94 FRONT VISE 1
90725-95 REAR VISE 1
90725-96 VISE HANDLE 1
90725-96-1 LOCK WASHER 3/8” 2
90725-96-2 WASHER 3/8” 1
90725-97 HEX HEAD BOLT 3/8” X 1 1/2” 1
90725-98 HEX HEAD BOLT 1/2” X 1 1/2” 1
90725-98-1 LOCK WASHER 1/2” 2
90725-98-2 WASHER 1/2” 1
90725-99 HEX HEAD BOLT 1/2 X 1 1/4” 1
90725-100 SCALE 1
90725-101 CAP SCREW 3/8” X 1 3/4” 1
90725-101-1 NUT 3/8” 1
90725-102 HOSE 1” 1
90725-103 PUMP 1
26
PARTS LIST
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
PART # DESCRIPTION SPECIFICATIONS QTY
90725-104 HEX HEAD BOLT 1/4” X 1/2” 4
90725-105 STRAIN RELIEF 1
90725-107 COOLANT TANK 1
90725-108 HOSE FITTING 1
90725-109 HOSE CLAMP 13 MM 1
90725-110 HOSE 5/16” 1
90725-111 SAW ARM 1
90725-112N SELF-TAPPING SCREW 6 X 20 4
90725-113 PLUG 1
90725-114N GEAR BOX COVER 1
90725-115N GEAR BOX GASKET 1
90725-116 WORM GEAR 1
90725-117 KEY 6 X 20 1
90725-118 BALL BEARING 6005 3
90725-119 HEX HEAD BOLT 3/8” X 1” 1
90725-119-1 LOCK WASHER 3/8” 1
90725-119-2 WASHER 3/8” X 35 X 4 1
90725-120 OIL SEAL 25.47.7 1
90725-121N GEAR BOX 1
90725-122 LOCK WASHER 5/16” 4
90725-123 HEX HEAD BOLT 5/16” X 1 1/4” 4
90725-123-1 SET SCREW 1/4” X 3/8” 2
90725-124 BLADE WHEEL (REAR) 1
90725-125 BEARING BUSHING 1
90725-126 CAP SCREW 3/16” X 5/8” 3
90725-127 BLADE 1
90725-128 BLADE BACK COVER 1
90725-129 WHEEL COVER 1
90725-130 LOCK KNOB 1/4” X 1/2” 2
90725-130-1 WASHER 1/4” 2
90725-131 GUIDE ADJUSTABLE KNOB 2
90725-132 ADJUSTABLE BRACKET (REAR) 1
90725-133 THRUST BEARING 608 ZZ 2
90725-134 BLADE ADJUSTABLE SEAT (REAR) 1
90725-134N BLADE ADJUSTABLE SEAT (FRONT) 1
90725-135 PIN 2
90725-136 ECCENTRIC SHAFT ASSEMBLY 2
90725-136-1 CENTER SHAFT ASSEMBLY 2
90725-137 NUT 3/8” X 24UNF 4
90725-137-1 LOCK WASHER 3/8” 4
90725-138 WASHER 5/16” 2
90725-139 LOCK WASHER 5/16” 2
90725-140 CAP SCREW 5/16” X 1 1/8” 1
90725-141 SCREW 1/4” X 1/2” 2
90725-142 BEARING GUARD 1
90725-143 SCREW 4
90725-144 SCREW 3/8” X 1 1/4” 2
90725-145 TOP SUPPORT 1
90725-146 LOCK WASHER 3/8” 2
90725-147 NUT 3/8” 2
27
PARTS LIST
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
PART # DESCRIPTION SPECIFICATIONS QTY
90725-148 SCREW 1/4” X 1/2” 2
90725-149 WASHER 1/4” 2
90725-150 BRUSH HOLDER 1
90725-151 HEX HEAD BOLT 5/16” X 2 1/2” 2
90725-152 NUT 5/16” 2
90725-153 BRUSH 1
90725-154 HEX HEAD BOLT 5/16 X 5/8” 3
90725-154-1 LOCK WASHER 5/16” 3
90725-155 CONTROL PANEL 1
90725-156 VALVE COCK 1
90725-157 SET SCREW 1/4” X 1/4” 1
90725-158 VALVE COCK SUPPORT 1
90725-159 VALVE 1
90725-160 SCREW 3/16” X 3/8” 2
90725-161 CAP SCREW 5/16” X 1 1/8” 1
90725-161-1 LOCK WASHER 5/16” 1
90725-162 LIMIT SWITCH 1
90725-163 ADJUSTMENT BRACKET (FRONT) 1
90725-164 BLADE GUARD 1
90725-164-1 SCREW 3/16” 1/4” 2
90725-165 HEX HEAD BOLT 1/4” X 1/2” 4
90725-166 SLIDING GUIDE PLATE 2
90725-167 SET SCREW 5/16 X 3/4” 1
90725-168 HEX HEAD BOLT 5/16” X 1 1/2” 2
90725-169 BLADE TENSION SLIDING BLOCK 1
90725-170 HEX HEAD BOLT 1/4” X 1/2” 1
90725-170-1 LOCK WASHER 1/4” 1
90725-170-2 WASHER 1/4” 1
90725-171 SLIDING DRAW BLOCK 1
90725-172 BRACKET 1
90725-173 BEARING BUSHING (FRONT) 1
90725-173-1 BEARING BUSHING (REAR) 1
90725-174 BEARING 6203 ZZ 2
90725-175 BLADE WHEEL (FRONT) 1
90725-176 WASHER 5/16” 1
90725-176-1 LOCK WASHER 5/16” 1
90725-177 HEX HEAD BOLT 5/16 X 3/4” 1
90725-178 SCREW 1/4” X 1/2” 4
90725-179 WASHER 1/4” 4
90725-180 WASHER 3/8” 1
90725-181 BLADE TENSION ADJUSTMENT HANDLE 1
90725-182 LIMIT SWITCH BRACKET 1
90725-182-1 CAP SCREW 3/16” X 3/8” 2
90725-183 BELT 3V - 270 1
90725-184 PULLEY 1
90725-185 MOTOR PULLEY 1
90725-186 SET SCREW 5/16” X 3/8” 3
90725-187 HEX HEAD BOLT 1/4” X 1/2” 2
90725-188 WASHER 1/4” 2
90725-189 PULLEY COVER 1
28
PARTS LIST
IMPORTANT: When ordering replacement parts, always give the model number, serial number of the
machine and part number. Also a brief description of each item and quantity desired.
PART # DESCRIPTION SPECIFICATIONS QTY
90725-190 PULLEY COVER LOCK KNOB 1
90725-191 KEY 5 MM 1
90725-192 MOTOR 1
90725-193 HEX HEAD BOLT 5/16” X 1” 4
90725-194 MOTOR MOUNTING PLATE 1
90725-195 WASHER 5/16” 4
90725-196 LOCK WASHER 5/16” 4
90725-197 NUT 5/16” 4
90725-198 RETENTION RING S-17 1
90725-199 BEARING 6003 3
90725-200 BLOCK PLATE 1
90725-201 OIL SEAL 17.35.7 1
90725-202 BEARING BUSHING 1
90725-203 GEAR SHAFT 1
90725-204 HEX HEAD BOLT 1/4” X 1/2” 2
90725-205 WASHER 1/4” 2
90725-206 SUPPORT PLATE 1
90725-207 LIMIT SWITCH RACK 1
90725-208 LIMIT SWITCH STOP PLATE 1
90725-209 CAP SCREW 3/16”X 3/8” 2
90725-210 SCREW 3/16” X 1 1/4” 2
90725-211 LOCK WASHER 1/4” 1
90725-212 HEX HEAD BOLT 1/4” X 1/2” 1
90725-213 NUT 1/4” 1
90725-214 HEX HEAD BOLT 1/4” X 1/2” 1
90725-215 WASHER 1/4” 1
90725-216 STRAIN RELIEF FITTING 1
90725-217 RETENTION RING R47 2
90725-218 HEX HEAD BOLT 5/16” X 1 1/4” 1
90725-219 NUT 5/16” 1
NOTES
29
8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3
Tel.: (514) 326-1161
Fax: (514) 326-5565 - Parts & Service / (514) 326-5555 - Order Desk
orderdesk@general.ca
www.general.ca
Follow us:
Loading...