|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
710 |
Professional |
||||||||||||||||||
PROSENSOR |
STUD |
||||||||||||||||||
FINDER |
IMPORTANT: READ BEFORE USING. SAVE THESE INSTRUCTIONS.
Operating/Safety Instructions
FRANKLIN SENSORS PROSENSOR 710
Congratulations on selecting the most advanced wall sensor on the market. Your ProSensor 710 incorporates advanced technology that precisely senses the surface in thirteen locations simultaneously, then instantly identifies the location(s) of hidden object(s). It is the easiest-to-use, fastest, and most accurate stud finder on the market.
SAFETY RULES FOR THE PROSENSOR 710
WARNING: Read all instructions before use. Failure to follow safety instructions may result in electric shock, fire, and/or serious injury and death.
SAVE THESE INSTRUCTIONS
WARNING: It is possible that there may be wood, metal, wiring, or other objects behind the surface that are not detected. It is also possible that the stud finder may detect pipes, wires, or other objects that the user may not want it to detect. The stud finder is designed to detect any inconsistency without identifying the nature of the inconsistency. The stud finder does not identify what type of object it detects. The illuminated LEDs may indicate the location of many different features including, but not limited to, studs, beams, water pipes, gas pipes, wires, an inconsistency in the surface material or
paint, etc.
WARNING: TURN OFF all gas, water, and electric power before using any drilling or penetrating devices or equipment including drills, saws, routers, hammers, nails, screws, etc.
WARNING: The stud finder alone should not be relied upon exclusively to locate objects behind a scanned surface. Use other sources of information to help locate objects. Other sources of information may include, but is not limited to, construction plans, visible points of entry of pipes, location of switches and outlets, and standard 16" and 24" stud spacing practices.
FAILURE TO TAKE THESE AND OTHER NECESSARY PRECAUTIONS COULD RESULT IN ELECTRIC SHOCK, FIRE, AND/OR SERIOUS INJURY AND DEATH.
Clean
Before turning on, ensure that the stud finder is clean and dry. If necessary, wipe the stud finder dry using a clean cloth. If the detector is wet or dirty it may not operate properly.
Temperature
If the stud finder is subject to a significant temperature change, allow it adjust to the ambient temperature before using. The entire area of the sensor board should be at a similar temperature for best operation.
|
|
|
|
|
|
|
|
|
|
|
|
OPERATING INSTRUCTIONS |
|
|
|
|
|
|
|
|
|
WARRANTY |
|
1 |
3 |
6 |
|
|
STICKERS / DECALS |
|
|
|
Franklin Sensors warrants this product to be free |
||
|
|
|
|
|
|
|
|
||||
|
|
|
1. LED Lights |
|
Do not place decals or stickers, especially metal |
from defects in material and workmanship for |
|||||
2 |
|
|
2. Ergonomic Handle |
|
decals or stickers on the sensor board, or on the |
one year. This LIMITED WARRANTY does not |
|||||
|
|
|
stud finder in any place. |
|
|
|
cover products that are improperly used, abused, |
||||
|
|
3. “On” Button |
|
|
|
|
|||||
|
|
|
|
DISASSEMBLY / TEFLON PADS |
|
or altered. Defective products will be replaced or |
|||||
|
|
|
4. Battery Cover |
|
|
repaired. If a product is found to be defective |
|||||
|
|
|
5. Detector Housing |
|
Do not disassemble the stud finder or remove |
within the warranty period, Franklin Sensors will, |
|||||
|
|
|
6. Sensor Board |
|
the teflon pads that are on the bottom. The stud |
at its sole discretion, either repair or replace the |
|||||
|
|
|
|
finder will not operate correctly without the |
defective product. This limited warranty does not |
||||||
5 |
|
4 |
|
|
|||||||
|
|
|
teflon pads properly in place. |
|
|
|
apply to products that are subjected to freight |
||||
|
|
|
|
|
|
|
|
||||
|
|
|
|
|
|
BATTERIES |
|
|
|
damage, accident, abuse, alteration, misuse, |
|
TO OPERATE: |
|
|
SENSING THROUGH DIFFERENT MATERIALS: |
|
|
|
improper repair, etc. Franklin Sensors and |
||||
|
|
The ProSensor 710 uses 2 AA batteries. Use |
Franklin Sensors’ authorized distributors shall |
||||||||
|
|
|
|
|
|
alkaline batteries only; do not use rechargeable |
bear no other liability or obligation under |
||||
|
|
|
Moisture |
|
batteries. Replace both batteries at the |
|
this warranty. |
||||
|
|
|
The scanned surface should be clean and dry. |
same time. |
|
|
|
|
|
||
|
|
|
Paint and wallpaper need to be completely dry |
REPLACING THE BATTERIES |
|
Franklin Sensors does not authorize any person or |
|||||
|
|
|
before scanning for studs. It may take up to |
|
representative to assume or grant any other |
||||||
|
|
|
2 weeks for wallpaper to dry enough to |
|
• Remove battery cover, |
|
|
|
warranty or obligation with the sale of this |
||
|
|
|
detect studs. |
|
|
|
|
product. Franklin Sensors’ limited warranty is |
|||
|
|
|
|
|
|
by sliding the cover to |
|
|
|
valid only if you retain proof of purchase from |
|
|
|
|
Curved Surfaces |
|
the left and lifting. |
|
|
|
Franklin Sensors or a Franklin Sensors authorized |
||
|
|
|
There is a minor degree of curvature in the walls |
Remove batteries and |
|
|
|
dealer for this product. If you purchase this |
|||
|
|
|
of most homes and buildings. The curvature is |
dispose of the |
|
|
|
product from any other source, your purchase is |
|||
|
|
|
small enough that it may not be noticed. The |
batteries properly. Please recycle. |
|
“AS IS,” which means Franklin Sensors grants |
|||||
|
|
|
ProSensor 710 can detect objects through |
• Replace with 2 new AA alkaline batteries. |
you no warranty, and that you, not Franklin |
||||||
• Hold the stud finder by the handle. Do not |
|
curved surfaces because the ProSensor 710 has a |
Sensors, assume the entire risk of the quality and |
||||||||
touch the detector outside of the handle area |
|
sensor board that bends slightly to match the |
• Replace battery cover. Close battery cover |
performance of this product. The warranty |
|||||||
while scanning. |
|
|
contour of most walls. Press the stud finder firmly |
period for any replaced and/or repaired part |
|||||||
|
|
|
against the surface and the sensor board will |
by sliding the cover to the right until it snaps |
under this warranty shall expire at the end of the |
||||||
• Place the ProSensor 710 firmly against the |
|
match the contour of the surface, and provide |
into place. |
|
|
|
original warranty period. |
||||
surface and press the “on” button. Continue to |
|
the best reading. |
|
STORAGE |
|
|
|
|
|
||
hold the “on” button down. |
|
|
|
|
|
|
|
|
ALL EXPRESS AND IMPLIED WARRANTIES FOR |
||
|
|
|
Foil-Backed Insulation |
|
Store the stud finder in a clean, dry place at |
THIS PRODUCT, ARE LIMITED IN DURATION TO |
|||||
• LED lights will immediately display the location |
|
Although foil covered insulation is not very |
room temperature. Protect against direct sunlight |
THE WARRANTY PERIOD, AND NO |
|||||||
of any hidden objects. |
|
|
common, metal foil can cause inconsistent |
and moisture. |
|
|
|
WARRANTIES, WHETHER EXPRESS OR |
|||
|
|
|
readings with all electronic stud finders, |
|
ENVIRONMENTAL CONDITIONS |
|
IMPLIED, WILL APPLY AFTER THIS PERIOD. THIS |
||||
• The “on” button may be pressed before or |
|
including the ProSensor 710. |
|
|
WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL |
||||||
after placing the stud finder on the surface to |
|
|
|
|
Storage Temperature |
0°F to 120°F |
OTHER OBLIGATIONS, LIABILITIES OR |
||||
be scanned. The stud finder will detect studs |
|
Metallic Content in Wallpaper |
|
WARRANTIES. In no event shall Franklin Sensors |
|||||||
without sliding the stud finder across the wall, |
|
Wallpaper with metallic content can block the |
|
(-18°C to 50°C) |
or its licensed distributors be liable or |
||||||
but will also operate correctly if it is slid across |
|
detector’s signals. |
|
Operating Temperature |
32°F to 110°F |
responsible for INCIDENTAL OR |
|||||
the wall. |
|
|
|
|
|
CONSEQUENTIAL DAMAGES or for any other |
|||||
|
|
|
Textured Walls and Acoustic Ceilings |
|
|
(0°C to 43°C) |
direct or indirect damage, loss, cost, expense or |
||||
|
|
|
The ProSensor 710 is capable of detecting studs |
Storage Humidity |
0% to 90% |
fee. Some states do not allow the exclusion or |
|||||
|
|
|
through many textured surfaces. The stud finder |
limitation of incidental or consequential |
|||||||
|
|
|
should be placed firmly against the surface for |
|
relative humidity |
damages, so this exclusion or limitation may not |
|||||
|
|
|
best results. |
|
|
(non-condensing) |
apply to you. This warranty gives you specific |
||||
|
|
|
Lath and Plaster |
|
Operating Humidity |
0% to 90% |
legal rights and you may also have other rights |
||||
|
|
|
|
that vary from state to state. |
|||||||
|
|
|
Irregularities in plaster thickness and variations in |
|
relative humidity |
|
|
||||
|
|
|
construction materials can make it difficult to |
|
(non-condensing) |
In the event of a product defect, please return |
|||||
|
|
|
locate studs behind lath and plaster walls. Also, |
DISPOSAL |
|
|
|
the product postage paid with proof of |
|||
|
|
|
if the plaster has a mesh reinforcement, the stud |
|
|
|
purchase to: |
||||
|
|
|
finder may not be able to detect through the |
Stud finders and packaging should be sorted |
|
|
|||||
|
|
|
metal mesh. Although many users have success |
for recycling. |
|
|
|
Franklin Sensors Inc. |
|||
|
|
|
with the ProSensor 710 on lath and plaster walls, |
|
|
|
|
Attn: Returns Department |
|||
• If more than one hidden object is present, the |
|
there is no guarantee the ProSensor 710 will |
FCC PART 15 CLASS B REGISTRATION |
13601 W. McMillan Road Suite 102 - 170 |
|||||||
stud finder will show the location of more than |
|
work on all lath and plaster walls. |
|
WARNING |
|
|
|
Boise, ID 83713 |
|||
one hidden object. |
|
|
Tile, Flooring, Roofing, and on the Outside |
This device complies with Part 15 of FCC rules. |
(208) 918-2403 |
||||||
|
|
|
Operation is subject to the following two |
returns@franklinsensors.com |
|||||||
|
|
|
of the House |
|
conditions: |
|
|
|
Hours of Operation: Monday-Friday, |
||
|
|
|
The ProSensor 710 works by measuring the |
1. This device may not cause harmful |
|
8 AM to 5 PM, |
|||||
|
|
|
density of material behind the sensors to |
interference, |
|
|
|
Mountain Time Zone |
|||
|
|
|
determine the location of studs. Due to the |
and |
|
|
|
|
|
||
|
|
|
variability in the density of materials in tile, |
2. This device must accept any interference |
US and Foreign Patents Pending. |
||||||
|
|
|
flooring, roofing, and on the outside of the |
received, including interference that may |
|
|
|||||
|
|
|
house, we do not recommend the ProSensor |
cause undesired operation. |
|
|
|
Rev. E1 |
|||
|
|
|
710 for use in these applications. |
|
|
|
|
|
|
|
|
|
|
|
TROUBLESHOOTINGI |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
CONDITION |
PROBABLE CAUSE |
|
|
SOLUTION |
|
|
||
• LED lights indicate the width of hidden |
|
No LED lights come on. |
|
Weak battery. |
|
|
|
Replace with 2 new AA alkaline batteries. |
|||
|
|
|
|
|
|
|
|
|
|
||
object(s). |
|
|
Stud finder only works momentarily. |
|
The “on” button isn’t being held down. |
|
|
Hold the “on” button down until you have completed your scan. |
|||
|
|
|
|
|
|
|
|
||||
|
|
|
The LED lights are indicating the location of pipes |
|
The ProSensor 710 indicates the location of inconsistencies. The |
|
Look for evenly placed studs on either side (16", 24", on center, etc.) Scan |
||||
|
|
|
and wires, not just studs. |
|
LED lights may indicate the location of a pipe, electrical wiring, |
|
above the location and below the location to confirm results. Use caution |
||||
|
|
|
|
|
other objects near the surface being scanned, or an inconsistency |
before penetrating wall. See the SAFETY RULES FOR THE PROSENSOR 710. |
|||||
|
|
|
|
|
in the surface material or paint, etc. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|||||
|
|
|
Difficulty starting a scan near doors and windows. |
Double studs, triple studs and solid headers are often present |
|
Begin the scan away from the window or door, then move the stud finder to the |
|||||
|
|
|
|
|
around doors and windows. The stud finder requires the presence |
area around the window or door. For best results, keep stud finder 3" away from |
|||||
|
|
|
|
|
of a region without studs to correctly identify studs. |
|
|
wood trim, outlets, switches, etc. |
|||
|
|
|
|
|
|
|
|
||||
|
|
|
Stud finder doesn’t work through new wall paper. |
|
The moisture in the wall after wall papering can block the stud |
|
Wait until the wallpaper is dry. It may take up to 2 weeks for the paper to dry |
||||
|
|
|
|
|
finder’s signal. |
|
|
|
sufficiently. |
|
|
|
|
|
|
|
|
|
|
||||
|
|
|
My house was built prior to about 1960. The walls |
|
Older houses that were built with lath and plaster, instead of |
|
Try using the stud finder at a higher point on the wall, or a lower point on |
||||
|
|
|
are lath and plaster. The stud finder doesn’t work |
|
sheet rock, often have too much inconsistency in the walls for the |
|
the wall. |
|
|
||
|
|
|
very well anywhere in my house. |
|
detector to work reliably. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
|
|
Inconsistent readings. |
|
Curved surface. |
|
|
|
Press the stud finder firmly against the wall so that the contour of the sensor |
||
|
|
|
|
|
|
|
|
|
board matches the slight contour of the wall. |
||
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
Anomaly in the surface material. |
|
|
Test at a higher location, or lower location on the wall. |
|||
• On some surfaces it may be helpful to slide the |
|
|
|
|
|
|
|||||
|
|
|
Sometimes after scanning the wall for a period of time the |
|
Release the button and press the button again. |
||||||
stud finder up and down to confirm the |
|
|
|
readings seem to be less consistent. |
|
|
|
|
|
||
location of a stud. |
|
|
When I put my hand in front of the sensor board, |
The stud finder is designed for detecting features in walls, |
|
Place the stud finder on the wall to detect hidden features. |
|||||
|
|
|
the readings are not what I would expect. |
|
not hands. |
|
|
|
|
|
|
|
|
|
The LED lights sometimes seem to light up |
|
Wires, pipes, or other construction inconsistencies can cause |
|
Test at points on the wall that are higher, or lower. The stud finder may also |
||||
|
|
|
sporadically or inconsistently. |
|
erratic or erroneous readings. Features on the opposite side of a |
|
work best if it is used more than 3 inches away from metal objects such as |
||||
|
|
|
|
|
wall may also be a source of |
|
|
outlets, light switches, etc. |
|||
|
|
|
|
|
inconsistent readings. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|